NavRoad NR430BT User Manual

Download

NR430BT

User’s manual

www.navroad.com

The product and the information contained herein may be changed at an

y time without prior notification. This manual or any parts of it may not be reproduced, tr

ansmitted in any form either electronically or mechanically(including photo copying) without the express written consent of NavRoad.

Table of Contents

1. Safety Information

1.1 Caution

1.2 Normal Care

2. Product Information

2.1 Package Contents

2.2 Installing to the Vehicle

3. Basic Operations

3.1 Getting Start

3.2 Main Screen

3.3 Phone

3.4 Music

3.5 Photos

3.6 Movies

3.7 Settings

4. Service & Support

4.1 Technical Support

4.2 Registration

4.3 Maintenance & Troubleshooting Info.

4.4 Warranty Statement

5. Fact Sheet

5.1 Product Specification

1.1 Caution…

Before starting installing or operating your navigation system, Please be familiar with this Manual Completely for your safety. Your unsuitable installation or operation of this device may cause injury or death.

Safety Precautions

1. Use the car charger included with the package, using power adapters other than the one provided will result in malfunction and could prove dangerous.

2. Do not use the car charger in a wet environment. When hands and fee

t are wet, do not touch the car charger.

4. While using the car charger ensure that

the area is well ventilated. Do not let paper or other material cover the power adaptor, as this will interfere with cooling. Do not use the power

adaptor whilst it is in a bag.

Chapter 1 Safety Information

5. Do not attempt to repair the device. If device is damaged or is in a wet environment, replace the device immediately.

6. About the battery

- Use only the original factory approved charger.

- A Lithium battery is built in to the device. To prevent fire or s

kin burns, do not disassemble, pierce, impact, or expose the battery to fire. The battery will crack, explode, or release dangerous chemicals if placed in a fire.

7. Important instructions

- Note : Replacing with an incorrect battery may result in an explosion

. When disposing of the battery, follow the instructions. The repl

acement battery must be original factory approved.

- Regulations must be observed when recy

cling or disposing of

batteries.

- The battery should only be used in this device.

1.2 Normal Care

The NavRoad NR430BT is constructed of high quality materials and does not require user maintenance other than cleaning.

Cleaning the Unit

Clean the unit’s outer casing using a cloth dampened with a mild det

ergent solution and the wipe dry. Avoid chemical cleaners

and solvents that can damage plastic components.

Caring for the Touch Screen

The touch screen is intended to be operated with a finger. Never use a hard or sh

arp object to operate the touch screen or damage may result. Though a PDA stylus can also be used to operate the touch screen, never attempt this while operating a vehicle.

Clean the touch screen using a soft, clean, lint-free cloth. Use water, isopropyl alcohol, or eyeglass cleaner if needed. Apply the liquid to the cloth and gently wipe the touch screen.

Protecting your NavRoad NR430BT

- Do not expose the unit to water or other forms of moisture; the NavRoad NR430BT is not waterproof.

- Do not store the unit where prolonged exposure to extreme temperat

ures can occur (such as in the trunk of a car), as

permanent damage may result.

- To avoid theft, do not leave your NR430B

T in plain sight when

you leave your vehicle.

2.1 Package Contents

Please check the contents in the Box.

Manual

SD card with navigation software

and maps

Chapter 2 Product Information

*depends on version

2.2 Installing to the Vehicle

Take care when mounting the NavRoad NR430BT in your vehicle, whether using the windshield mount or other mount, that it does not obstruct the driver’s view of the road. Make sure that the placement of the NAVROAD NR430BT and cable does not interfere with the operation of vehicle safety devices, such as air bags. You assume the risks associated with damage to your vehicle or vehicle’s occupants as a result of how you choose to mount the NavRoad NR430BT.

1. Attach the windshield mount to the back of the docking cradle.

2. Press the windshield mount to the glass and slide the locking lever toward

the glass.

3. Insert the NavRoad NR430BT onto the docking cradle.

4. Plug the power cable into rear dc input of the docking cradle as show

5. Plug the car charger into your vehicles cigarette lighter or 12 vol

t receptacle.

6. Installation is complete, and you are ready to turn the Nav

Road NR430BT on and go.

3.1 Getting Start

Performing the initial Start Up

Slide the Battery ON/OFF switch the ON position. Note : Always leave the Battery ON/OFF Switch in the ON Position for normal operation.

Power ON/OFF

Your device turns on when pull down the bar switch to Power.

Chapter 3 Basic Operations

Follow the instructions on the Installation Poster to dock your NavRoad NR430BT in your car. The first time you turn on your NavRoad NR430BT, it may take up to 10 seconds to start. To power off your NavRoad NR430BT, pull down the bar switch.

Locating your current position

Your NavRoad NR430BT must be outside to locate your current position. The first time you start your NavRoad, it can take up to 5 minutes to find your current position. If it takes longer than 5 minutes, make sure that you are in an open place without tall buildings or trees around you. In the future, your position will be found much faster, normally wi

thin a few seconds. Once your NavRoad has located your current position, the Driv

ing View is shown in full color and shows your position on

the map.

Note: Some vehicles have a heat reflective shield embedded in the windshield that may prevent NavRoad NR430BT from locating your current position. If this is a problem in your vehicle, use the NavRoad NR430BT External Antenna Kit (available as an accessory).

Understanding Hardware Components

1. Main Unit

Front, Left and Top Side Components.

Ref

Component Description

1 Menu Button

Display each menu screen and r

eturn to the previous mode. For Hold function, please press R

eturn key more than 2 seconds.

2 5 Way Joystick

This is 5 way joysticks for na

vigation and select menu.

3 Volume Control Adjusts the volume level

4 Touch Screen

Tap the screen with your fingertip t

o select menu commands.

5 Charge Indicator

Glows in bright Red to indicate t

hat the battery is charging, and turns green when the battery is fully charged

6 MIC This is for receiving voice

7 Hand String Hole Hand string attaches to this hole

Headphone Conne

ctor

Connects to stereo headphones

Mini-USB Conne

ctor

Connects to the USB cable for home charging or Sync.

10 Speaker Sends out sounds and voice

11 GPS Antenna

Receives signals from the GPS s

atellites overhead.

12 Stylus Pen

Using this stylus pen for tap the screen and

to select menu.

Rear, Right and Bottom, Side Components.

Ref Component Description

1 Power Button Turns on and off the device.

2 SD Slot Accepts a SD card for accessing

date such as MP3 music.

3 External Antenna

Connector

This Connector(under rubber dust cover) allows use of an optional external GPS antenna with magnetic mount, which may be positioned on top of the car for better GPS signal reception in areas with poor reception.

4 Reset Button Restarts your device(soft reset)

5 Docking Port This port should be connected with

docking cradle.

2. Docking Cradle

Front, Rear and Inner Side Components.

Ref Component Description

1 Docking Port This port should be connected

the NavRoad device

2 Push Button This button is working for

disconnect with NavRoad Device

3 DC Input DC 5V input

4 TMC Connector The TMC(Traffic Message

Channel) module for receiving TMC information.

5 Audio out External Sound output

6 External MIC

Connector

External MIC input for better voice receiving in hand-free calling.

3.2 Main Screen

3.3 Phone

3.3.1 About Phone

Phone Menu allows you to use your device as a hands-free

device for a mobile phone supporting Bluetooth connection. You can tap your device to place and receive phone calls instead of picking up the mobile phone.

3.3.2 Pairing with a Mobile Phone

1. Tap the Phone button on the main screen and the Pair Mode button. Bluetooth radio turns on.

If this is the first time you use the program, your device will switch to Pair Mode and wait for the pairing action from your mobile phone maximum for 4 minutes. The connection will be established as long as you initiate the pairing process.

If prompted to enter the pincode (or passkey) on your mobile phone, tap the passkey specified by the NavRoad NR430BT (dhe default is 1234) and tap OK.

4. You will see the Phone main screen after the pairing is

completed. The status bar at the bottom shows the name of the mobile phone connected.

The next time you run the Phone program, your device will automatically search and pair with one of the last connected mobile phones.

NOTE:

• Your device must be in Pair Mode for the mobile phone to discover your device. If you need to manually set your device to Pair Mode, tap Pair Mode on the Phone main screen.

• Some mobile phones can automatically connect the handsfree service.

• Up to 5 sets of paired mobile phones can be stored. A 6th paired mobile phone will replace the oldest one.

• The Phone program cannot access the data such as the phone book and call history stored in a connected mobile phone.

3.3.3 Placing a Call

After pairing with your mobile phone, you can place a call using any of the four buttons (Call, Call History, and Redial) on the Phone main screen.

By tapping the Call button on the Phone main screen, you can enter the telephone number with the onscreen keypad. After

entering the telephone number, tap

to place the call.

NOTE:

• To delete the last digit entered, tap the Backspace

button.

• The other two buttons allow you to switch to Home and Call History screens

Call History

Tap the Call History button on the Phone main screen to display the recent incoming, outgoing, or missed calls together with information such as date, time, and duration of each call.

Tap the respective button (incoming, outgoing, or missed ) to view the last 20 calls of the selected type.

With an item selected, you can tap

to dial the number,

to delete the item. To clear all items in the current list, tap

Redial

Tap the Redial button on

the Phone main screen

to dial the last number you called or received.

3.3.4 Operations During a Call

During a call, four functions are available:

• If you need to input other numbers, such as an extension

number, tap to open the keypad and tap the digits. The keypad will close when you tap the button again or when there has been no input for 5 seconds.

• Tap

to mute your sound so that the other party cannot hear you. To end the mute mode, tap the same button again.

• Tap

to end the call.

• Tap to switch the call to your mobile phone.

To switch back to your device, tap the same button again.

3.3.5 Receiving a Call

When you have a call after pairing with a mobile phone, the device rings and displays the Incoming Call screen.

To accept the call, tap .

To reject the call, tap

To mute the ring tone before receiving or rejecting, tap

3.3.6 Connecting Devices

Connect

By tapping the Connect button on the Phone main screen, you can manually search the last paired mobile phones for an available connection.

NOTE: To use the service of a remote device with Bluetooth capability, make sure that the remote device is in discoverable mode.

1. Tap Connect from Pho

ne main screen to search for

nearby devices.

The device list appears on the screen. Tap the target

device from the list of the devices.

Tap the device you want to use as a Hands-

Free

or a Headset .

4. When prompted to ente

r the passkey in your mobile

phone, Please, input the passkey requested by the NavRoad and tap OK.

Viewing Active Connections

After starting Phone menu, tap Connect to view the active

connections. After you tap an item, you can tap

disconnect the selected device.

3.3.7 Pair Mode

By tapping the Pair Mode button on the Phone main screen, you can manually set your device to Pair Mode. Within the duration for 4 minutes, you can initiate the pairing process on your mobile phone to discover your device as a hands-free device or a Headset.

3.3.8 About Preference

Your device incorporates Bluetooth wireless communications technology. Devices with Bluetooth capabilities can exchange information over a distance of bout 10 meters (30 feet) without requiring a physical connection. Preference allows you to configure and use the Bluetooth capabilities of your device.

Starting and Exiting Preference

1. Tap the Phone button on the Main Screen and then the Preference button.

2. When the Phone screen appears, tab Preference

3. The Preference screen appears as shown below.

To exit the program, tap . You will be back to the Phone screen.

Turning On/Off Bluetooth Radio

Whenever you start Preference, Bluetooth radio is turned on.

Exiting Preference doesn’t turn off Bluetooth radio. To turn off Blu

etooth radio, tap in the Preference screen.

Configuring Preference

After starting Preference, tap to configure Hands Free settings.

The available options are:

• Home Numbe

r : Allows you to edit the your home

number.

• Aut

o-Answer : You can tell your NR430BT to answer

every call automatically after a

certa

in time.

• Ring-

Tone : You can select one ring tone from 3 kinds of

ring tone which like to hear

3.4 Music

3.4.1 Starting and Exiting Music Player

Music turns your device into a Music player. It features:

Playb

ack of MP3 files

asic Playback controls such as play, pause, stop, next and

layback includes single selection playback, repeat, single

repeat, normal sequence and random sequence.

Tap the Music button on the Main menu to start the program. The control panel appears on the screen where you can easily control the player by tapping the control buttons.

To exit the program, tap

3.4.2 Preparing the MP3 Files for Your Device

Before using the program, have the MP3 files ready on a storage card.

3.4.3 Playing MP3 Files

1. If your files are in a storage card, insert the card into your device.

2. Tap the Mus

ic button on the Home screen to start the

program.

3. The program will search for the MP3 files in your device and in th

e storage card. When MP3 files are detected, they will be

showed to the play list.

4. To start the playback, tap Sele

ct button from the MP3 file

list . To control the playback, use the control buttons as described later.

3.4.4 MP3 Playback Controls

Control Button Name Description

Play/Pause Play or

paus

e the

playback.

Stop Stop the

ayback.

RWD/F.FWD Play

Rewi

nd or Fast Forward

Previous/Next Play the

ious or

next file.

Volume -/+ Increase or

decrease the v

olume. The indicator on the panel shows the current volume level.

Exit Close the

pro

gram and return to the Home screen.

Playback

Mode

Cycle through the following modes:

Repeated pl

ayback of the all files in the folder

Single pl

ayback of the current folder

Repeated pl

ayback of current file

Repeated pl

ayback of all files in random order

3.5 Photos

3.5.1 Starting and Exiting Photos

Photos allows you to view pictures in JPEG, GIF and BMP formats and view the Tap the Photos button on the Main menu to start the program.

3.5.2 Preparing the Pictures for Your Device

Before using the program, have the JPEG/GIF/BMP files ready on a storage card.

3.5.3 Viewing Pictures in List View

1. If your files are in a storage card, insert the card into

your device.

2. Tap t

he Photos button on the Main menu to start the

program.

. The program will search the matching files in the specific

folder on a storage card. It then displays the pictures in the list view. You can press the Up or Down arrow button to go to next or previous page.

3.5.4 Viewing a Picture in Full Screen

When you tap or a picture once in the list view, the picture is displayed in full screen. To go back to the list view, tap anywhere on the screen to display the P

icture list view screen.

3.5.6 Viewing the Slideshow

To view the slideshow of all your pictures, use one of the following ways:

1. When

in the list view, tap

to start the

slideshow.

2. When in f

ull screen, tap anywhere on the picture to

return in the list view screen.

3. Sets

the length of time each slide is displayed before

moving on to the next slide. Tap the button to switch to the next available option.

3.5.7 Rotating the picture

To rotate the picture, tap or in your favorites direction.

3.6 Movie

3.6.1 Starting and Exiting Movie Player

Movie turns your device into a Movie player. It features:

Playb

ack of Movie files

asic Playback controls such as play, pause, stop, next and

Tap the Movie

button on the Main menu to start the program. The control panel appears on the screen where you can easily control the player by tapping the control buttons.

To exit the program, tap

3.6.2 Preparing the Movie Files for Your Device

Before using the program, have the Movie files ready on a storage card.

3.6.3 Playing Movie Files

1. If your files are in a storage card, insert the card into

your device.

2. Tap t

he Movie button on the Main menu to start the

program.

. The program will search for the Movie files in the storage card. When Movie files are detected, they will be added to the Movie list.

. To start the movie, tap Select button. To control the playback, use the control buttons as described later.

3.6.4 Playing a Movie in Full Screen

When you tap or Movie screen once in the Movie player view, the Movie is played in full screen.

To go back to the Movie screen, t

ap anywhere on the screen to

display the Movie player list

view screen.

3.6.5 Movie Playback Controls

Control Button Name Description

Play/Pause Play or

paus

e the

playback.

Stop Stop the

ayback.

RWD/F.FWD Play

Rewi

nd or Fast Forward

Previous/Next Play the

ious or

next file.

Volume -/+ Increase or

dec

rease the volume. The indicator on the panel shows the current volume level.

Exit Close the

pro

gram and return to the Home screen.

3.7 Settings

3.7.1 Starting and Exiting Settings

You can customize the system settings such as backlight brightness, volume, and language. Once you change them again. Tap the Settings button on the Home screen. The Settings menu appears as shown

To exit Settings, tap . The following sections describe the various buttons and their functions.

3.7.2 Information

1. Tap the Settings button on the Main menu.

2. Tap t

he Information button.

3.7.3 Start Settings

1. Tap the Settings button on the Main menu.

2. Tap the Start Settings button.

To select the application which will run when swithing on the device, tap Start with Specific Application. You can choose from standard applications by tapping their appropriate icon.

You can select other application on the device or SD card by

apping

Then you can select the application from the list and tap OK to confirm.

. Move the knob along the track bar to adjust the volume. To decrease the volume, move the knob to the left. To increase the volume, move the knob to the right.

3.7.4 Default Settings

1. Tap the Settings button on the Main menu.

2. Tap t

he Default Settings button.

3. You can se

t default to your device in this option and if you click ‘Set Default’, your device will be back to default. Please, take care of use this option.

3.7.5 Brightness

1. Tap the Settings button on the Main menu.

2. Tap t

he Brightness button.

Click + or - to adjust the brightness of the backlight. To

darken the backlight, move the knob to the left. To lighten the backlight, move the knob to the right.

3.7.6 Change Language

NOTE: To change the language of the Map navigation software, use Map settings.

1. Tap t

he Settings button on the Main menu.

2. Tap t

he Language button.

Tap the Up/Down arrow button to select the desired

language.

. Tap OK the button for the new setting to take effect(Re-

booting).

3.7.7 Energy

To check the remaining power level of your battery and/or set up the power saving feature:

1. Tap t

he Settings button on the Main menu.

2. Tap t

he Energy button.

. The screen shows the remaining power of your battery.

You can set a timer to:

- automatically turn off your devic

e when it is idle for a set

period of time.

- automatically dim the LCD display when it is idle for a set p

eriod of time.

3.7.8 Touch Screen

You can calibrate the touch screen if it is not responding accurately to your taps.

1. Tap t

he Settings button on the Main menu.

2. Tap t

he Calibration button.

. Tap to start the calibration.

. Tap and hold the centre of the target.

5. When the target moves to another position, tap and hold

the center of the new target. Repeat each time to complete the calibration process.

6. When compl

eted within 5 seconds, tap no. 6.

3.7.9 Date/Time settings

To set Date, Time and Timezone tap the time display at the upper right corner of the display.

Set all required information and tap OK to con

firm.

4.1 Technical Support

If you need technical assistance or “how-to” help, or if you have a technical question about the functionality of your NAVROAD product, please contact us on the Internet at

www.navroad.com

On this web page you can find Frequently Asked Questions and the

ir answers and contact form.

Our Technical Support is available Monday through Friday, 10:00 a.m. to 4:00 p

.m. CET. After hours, you may leave a message by

contact form that will be returned within the next business day.

4.2 Registration

Please make sure to register your NAVROAD NR430BT at

www.navroad.com

. By registering, you will be informed of the

NavRoad NR430BT User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual