Navig[8]r NAVBIKE-GPS User Manual

USER MANUAL NAVBIKE-GPS
1 | P a g e
Please read carefully before use
USER MANUAL NAVBIKE-GPS
2 | P a g e
Table of Contents
USER MANUAL NAVBIKE-GPS
3 | P a g e
IMPORTANT SAFETY INSTRUCTIONS AND PRECAUTIONS
- Read all instructions carefully before use.
- Retain manuals for future reference.
- Use this product only in the manner described.
- Only use a water-dampened soft-cloth to clean the surface of this product.
- Only recommended batteries and accessories should be used with this product.
- If charging is required, it is recommended to thoroughly charge electronic devices for the first time overnight. Subsequent charges can be as needed. During charging, or extended use, the product may become warm.
- There are no user serviceable parts in this product.
- Un-authorized attempts to dismantle or repair this product will void product warranty.
- Do not use this product if you are in control of dangerous machinery such as a motor vehicle.
- Remove any power or data cords by pulling them from the plug and not the cord.
WHAT’S IN THE BOX
1 x NAVBIKE-GPS, 1 x CD software disc, 1 x charging cradle, 1 X bike mounting bracket with cable ties, 1 x user manual
Note: Please reset your watch before the first use
HOW TO RESET YOUR NAVBIKE-GPS
1.0 Reset the watch by pressing and holding all 4 (four) buttons of your NAVBIKE-GPS at once, until the screen resets. A beep indicator will be heard and all screen icons will flash together.
Note: This user manual is arranged in order of essential settings through to entry level and advanced user settings and features. By following the manual in this way, it will establish a better understanding of the product and an overall better product experience.
NAVIGATING THE SETTINGS SCREENS (ENTRY LEVEL)
2.0 Before using your NAVBIKE-GPS for the first time you must set your personal user information.
Note: Main screen settings menu options will automatically open within 3 seconds if you have not scrolled onto a different option. Although this may take some getting used to, this feature is
USER MANUAL NAVBIKE-GPS
4 | P a g e
designed to save the user time and to reduce the required button presses.
2.1 From the main time screen, use the MODE button to enter the main menu settings screen. Each press will move you past the following 7 options; > BIKE, CHRO (Timer / Chronograph), DATA, ALRM (Alarm), SET (User settings) and TIME
2.2 For the following example, you need to keep pressing the MODE button (from the main time screen) until SET appears on the screen. Then wait 3 seconds to enter this sub­ menu option.
2.3 Each subsequent press of the ST/STP/+ button will take you past the following 9 sub-menu options: > AUTO LAP, TIME, UNIT, USER, NIGHT, CONTRAST, CHIME, ALRM (Alarm) and ODO (Odometer)
Note 1: Although AUTO LAP is the first option; it will be discussed in the later section 11.0
SETTING YOUR USER INFORMATION - THE SET SCREEN
Setting the date and time
Note: This device has 2 separate settings for time (time zones)
3.0 Use the ST/STP/+ button to then move to the TIME screen in the sub-menu screen. Enter the screen by pressing VIEW/LAP. T1 (Time Zone 1) will appear. The “1” will be flashing.
3.1 Press the VIEW/LAP button to enter the T1 settings options.
Note: Each of the two time zone times, can either be set automatically via GPS or manually by the end user.
3.2 Use the ST/STP/+ button to toggle between MANUAL and GPS (the highlighted option will start flashing), then press the VIEW/LAP button to confirm
your choice.
3.2.0 Manual time setting: If selected the next screen to appear will be a time screen with “SET T1” at the bottom of the screen. The hour digit will begin flashing. The word “HOUR” will also be shown on the screen.
USER MANUAL NAVBIKE-GPS
5 | P a g e
3.2.1 Use a combination of the ST/STP/+ button to advance the digits, then the VIEW/LAP button to save the data and move to the next section.
3.2.2 The subsequent sections are: MINUTE, SECOND, YEAR, MONTH, DAY, 12/24H
(12 or 24 hour time format) then lastly D-M (Day then Month format) or M-D (Month then Day) format setting.
Note: As you scroll through these options, each number will start to flash and the name of the section will appear at the bottom of the screen. eg. Hour, minute, second etc
3.2.3 The next press of the VIEW/LAP button from this screen will take you back to the
TIME setting sub-menu.
3.2.4 To set the T2 (Time zone 2 field) press the VIEW/LAP button again to move back into the same TIME screen sub menu. T1 will appear again with the number “1 flashing. Press the ST/STP/+ button to toggle to Time Zone 2 (T2). T2 will be displayed with the “2” now flashing.
Note: Below the T2 on this screen, you will also see 3 (three) letters representing a city code. This is a unique feature to the T2 time option. We will discuss this in the next section GPS time setting.
3.2.5 To adjust the time for T2, following the points above (3.1 to 3.2.3)
Note: The below section 3.3.0 follows from point 3.2 above.
3.3.0 GPS time setting: If selected the next screen to appear will be the city screen, with three city code letters flashing. You have 36 city codes to choose from. Using the ST/STP/+ button scroll through the codes and use the VIEW/LAP button to confirm your choice.
Note 1: Only one main city (code) is represented for each time zone. If you can not find your specific city code, refer to the time zone numbers (eg. 2H, -5H) and make your selection in this fashion. These time zones are referred to as UTC. A table containing the numbers for Australia is supplied at the end of this document. Note 2: The time will be updated via GPS once the GPS feature is turned on. It does not update immediately after setting this option.
USER MANUAL NAVBIKE-GPS
6 | P a g e
3.3.1 Adjust the subsequent sections which are: DST ON /OFF (Daylight Savings Time), 12/24H (12 or 24 hour time format) then lastly D-M / M-D (Day then Month format or Month then Day) format setting.
3.3.2 Press the VIEW/LAP button again to return to the beginning TIME sub-main screen.
Note1: The below section 4.0 follows from point 3.0 above. Note2: Press the ST/STP/+ button to move to the UNIT settings.
Unit of Measure
4.0 Use the ST/STP/+ button to then move to the UNIT screen. Enter the screen by pressing VIEW/LAP. KM (Kilometres) will appear on the screen. (This is the default setting)
4.1 By pressing the ST/STP/+ button you can change the default to MI (Miles). Press the VIEW/LAP button to confirm your choice. The screen will move back to the UNIT main screen.
Note: The below section 5.0 follows from point 4.0 above. Note: Press the ST/STP/+ button to move to the USER settings.
User Details
5.0 Use the ST/STP/+ button to then move to the USER screen. Enter the screen by pressing VIEW/LAP. GENDER will appear on the screen.
5.1 Use the ST/STP/+ button to toggle between FEMALE and MALE. Use the VIEW/LAP button to confirm your choice
5.2 Use a combination of the ST/STP/+ button to adjust values and the VIEW/LAP button to save and move through the next screens.
5.3 The subsequent sections are: AGE, WEIGHT KG and HEIGHT CM
5.4 Press the VIEW/LAP button a last time to return to the main USER screen.
Note: The below section 6.0 follows from point 5.0 above. Note: Press the ST/STP/+ button to move to the NIGHT settings.
USER MANUAL NAVBIKE-GPS
7 | P a g e
Night (Backlight)
6.0 Use the ST/STP/+ button to then move to the NIGHT screen. Enter the screen by pressing VIEW/LAP.
6.1 Press the ST/STP/+ button to toggle the three options 10 SEC, 20 SEC and ON. Confirm your choice by pressing the VIEW/LAP button.
6.1.0 As the name suggests, each time the LIGHT/SET/- button is pressed the screen will illuminate for either 10 or 20 seconds where selected.
6.1.1 If ON if selected you can select certain times that the backlight will automatically turn on and off.
6.1.2 Once ON is selected, START TIME will appear.
6.1.3 After 3 seconds, a time screen will then automatically appear.
6.1.4 Use the ST/STP/+ button to adjust the hours noting AM/PM or 12/24 hour times. Press the VIEW/LAP button to move across to minutes and again use the ST/STP/+ button to adjust the minutes. Press the VIEW/LAP button to save and return to the START menu.
Note: Once you return back to the START menu screen you must press the ST/STP/+ button within 3 seconds to toggle to the END time screen, otherwise it will automatically enter back into the START screen. If this happens simply, press the MODE button to get back out of the START screen options and return back to the main START screen – then quickly press the ST/STP/+ button to then show END on the screen.
6.1.5 Move to the END screen. END will be shown on the screen. Wait 3 seconds to auto enter into the screen.
6.1.6 Adjust the time in the same manner as described in 6.1.2
Note: The below section 7.0 follows from point 6.0 above. Note: Press the ST/STP/+ button to move to the CONTRAST settings.
Contrast
7.0 Use the ST/STP/+ button to then move to the CONTRAST screen. Enter the screen by pressing VIEW/LAP. CONT will
appear on the screen.
7.1 A percentage number will be flashing (Usually 60% by default)
7.2 Repeatedly press the ST/STP/+ button to scroll through the
USER MANUAL NAVBIKE-GPS
8 | P a g e
values 10% to 100% for the CONTRAST value. The screen contrast will take a few seconds to adjust once you begin scrolling.
7.3 Press the VIEW/LAP button to confirm your choice and to return back to the CONTRAST screen.
Note: The below section 8.0 follows from point 7.0 above. Note: Press the ST/STP/+ button to move to the CHIME settings.
Chime
8.0 Use the ST/STP/+ button to then move to the CHIME screen. Enter the screen by pressing VIEW/LAP. CHIME will appear on the screen.
8.1 The word OFF or ON will be flashing. Use the ST/STP/+ button to toggle between ON and OFF. Press the VIEW/LAP button to confirm your choice. You will then be returned to the main CHIME screen.
Note 1: When CHIME is turned ON, an hourly chime will sound as well as a key tone each time a button is pressed. A chime bell icon will also appear on the screen as an indicator. Note 2: The below section 9.0 follows from point 8.0 above. Note 3: Press the ST/STP/+ button to move to the ALARM settings.
Alarm
Note: This device has 5 separate alarm settings. Navigate each screen using the ST/STP/+ button to change values and the VIEW/LAP button to save the value and to progress to the next value.
9.0 Use the ST/STP/+ button to then move to the ALARM screen. Enter the screen by pressing VIEW/LAP. T1 AL1 (or 1 to 5) will appear on the screen.
9.1 The number “1” in AL1 will be flashing. (To move to the next alarm press the ST/STP/+ button to change the value)
9.2 For this example lets set the time for AL1. While the number one in AL1 is flashing press the VIEW/LAP button to enter the alarm settings and to begin adjustment.
9.3 The hour digits will now be flashing. Use the ST/STP/+ and VIEW/LAP buttons to change and save the values, then move to the next sections.
9.4 Set the values for MINUTES, TIME ZONE and finally whether to turn the alarm ON or
USER MANUAL NAVBIKE-GPS
9 | P a g e
OFF.
9.5 Then, repeat the above steps from 9.1 to move to and set the alarms for each of the 5 alarm settings as needed. Then press the MODE button to return back the sub-menu ALRM screen
Note 1: When the alarm sounds it will sound for 20 seconds. Press any button to stop the alarm. This will stop the alarm without activating any other functions. Note 2: When any alarm is set, an alarm icon will appear on the display. Note 3: The below section 10.0 follows from point 9.0 above. Note: Press the ST/STP/+ button to move to the ODO settings.
ODO (Odometer)
10.0 Use the ST/STP/+ button to then move to the ODO screen. Enter the screen by pressing VIEW/LAP. A 5 digit number will appear with the far right digit flashing.
10.1 Use the ST/STP/+ button to advance this number (from 0 to 9) or the LIGHT/SET/- button to subtract the number (from 0 to 9)
10.2 Press the VIEW/LAP button to move to the next field (to the left) and repeat the process to change each number. Press the MODE button when finished and to return to the main ODO screen.
Note 1: The below section 11.0 follows from point 10.0 above. Note 2: Press the ST/STP/+ button to move to the AUTOLAP settings.
Setting AutoLap (Distances)
Note: Use this feature to use GPS tracking (discussed later in this user manual) to measure predetermined (race track) distances.
11.0 Use the ST/STP/+ button to then move to the AUTOLAP screen. Enter the screen by pressing VIEW/LAP.
11.1 Use the ST/STP/+ button to toggle between the following popular track lengths:
0.4, 1, 2, 3, 4, and 5 KM and OFF. Press VIEW/LAP to confirm your choice. Then use the ST/STP/+ button to select whether to turn the alert ON or OFF.
11.2 Press the VIEW/LAP button to confirm your choice and to return back the main AUTOLAP screen.
USER MANUAL NAVBIKE-GPS
10 | P a g e
Note: The above alert consists of an audio (‘Beep’) and visual reminder (the screen will illuminate temporarily)
Short Cuts
12.0 Press the LIGHT/SET/- button to either go the reverse way in menu options or use it in any screen to turn the backlight for the pre-determined amount of time.
12.1 From the main time screen, press and hold the LIGHT/SET/- button to access a shortlist of key menu settings from the main settings menu. These are TIME, NIGHT, CONTRAST, and CHIME. These features are set in the same methods as explained previously and are simply short cut links to the original settings menus.
12.2 From the main time screen, press and hold the VIEW/LAP button to swap the main screen time display from T1 to T2 and vice versa. Press and hold the VIEW/LAP button until the change has been made. (This can be up to 4 seconds.)
12.3 Press and hold the MODE button to turn the GPS search (and co-ordinates saving) ON or OFF.
Note 1: T1 (Time Zone 1) does not show a city code (after you have entered the time setting using the GPS option). Only T2 will show the city code.
Note 2: This concludes the ENTRY LEVEL USER features. Before we move onto the ADVANCED USER section, we will discuss some further GENERAL USER features. These features are accessed via the MAIN MENU and are either related to SUB MENU features or have shared
common screens. These features are the main menu features TIME and ALRM.
SHARED MAIN-MENU OPTIONS
13.0 TIME: This feature only has one function. It is to return you back to the main time screen after you have viewed, used or adjusted features or functions
13.1.1 Simply, press MODE button until TIME (from the main menu) appears on the screen, then wait 3 seconds to be returned back to the main time screen.
13.1 ALRM: From the main time screen, use the MODE button to scroll to the ALRM screen. By pressing the VIEW/LAP button you can toggle between each of the 5 alarms and use the ST/STP/+ to switch each alarm ON or OFF
TRACK AND FIELD FEATURES (ADVANCED USERS)
Note 1: The advanced user settings are BIKE, CHRO, and DATA Note 2: BIKE and CHRO (Chronograph) modes are both timer features and share the same time counter system. When the CHRO is started or stopped, the same time will appear in the BIKE mode.
USER MANUAL NAVBIKE-GPS
11 | P a g e
NOTE 3: BEFORE MOVING TO OTHER TIMER BASED SCREENS OR BEFORE TRYING TO ADJUST USER SETTINGS RELATING TO TIMERS, ALL CURRENT TIME RECORDS NEED TO BE RESET AND SAVED. IF THIS IS NOT DONE, YOU WILL BE LOCKED OUT OF ASSOCIATED SCREENS. AS TIMER SCREENS ARE SHARED, SIMPLY ENTER ANY TIMER SCREEN, STOP, RESET AND SAVE THE ACTIVE FILE TO PROCEED.
Note 4: Aside from the DATA feature, the BIKE and CHRO features although similar looking at first glace, are fundamentally different. Essentially both functions measure time but in different ways - put simply: a) The BIKE feature is a singular running timer with on screen statistics. b) The CHRO feature is a multiple lap timer without on screen statistics.
BIKE
14.0 From the main time screen, use the MODE button to toggle to BIKE. Wait 3 seconds to enter the option.
14.1 The screen will then display GPS and INDOOR. To set up the GPS section, press the VIEW/LAP button while GPS is flashing, alternatively toggle to INDOOR using the ST/STP/+ button and confirm your choice
Note 1: INDOOR means no GPS data will be recorded. Note 2: Aside from the initial GPS specific setup screens, the general operation of all time recording screens are the same under GPS as with INDOOR. The GPS signal is simply turned on or off before entering through to the later time screens. The GPS location data is not shown but tracked and stored for later viewing using the PC software only.
14.1.0 GPS: After pressing the VIEW/LAP button to select GPS, the SEARCH GPS screen will appear. Once GPS signal has been located, the screen will display GPS GO. (If indoor is selected, this step will not be shown) Press ST/STP/+ to begin tracking. A timer will begin rolling on the screen.
14.1.1 During operation there are two lower read outs that users can modify, to view different combinations of statistics. The SPEED however always remain at the top. a) Press the VIEW/LAP button to toggle the bottom section. The name of the setting chosen will flash momentarily before the feature begins results are shown working. These features are: DISTANCE , SPEED, CAL (Calories), CLOCK, ODO and CHRONO b) Press and hold the VIEW/LAP button to toggle the middle section (top section) in the same fashion as described above.
USER MANUAL NAVBIKE-GPS
12 | P a g e
14.1.2 Press the ST/STP/+ button to pause the timer (the screen will display STOP) and again to un-pause the timer.
14.1.3 From the STOP screen press the VIEW/LAP button to review your data before saving. The screen view combinations are as follows: a) CHRONO / ODO /
CALORIES, b) CALORIE / AVE PACE / MAX PACE and c) DISTANCE / CHRONO / STOP . Once paused, press and hold the ST/STP/+ to automatically reset and
save the file. (“Hold To Reset“ will be displayed during this operation, finally by the file number the record was saved to. You can then release the button)
Note 2: If the auto lap function is set, the watch will take lap recordings automatically based on the auto lap settings. A beep will sound on each lap if the ALERT feature is turned on from the settings menu. Turn the auto-lap feature off if it is not required.
CHRO (Chronograpgh)
Note: If AUTO LAP is switched on, the watch will take LAP times automatically based on your settings. Further depending on your CHIME setting, and audible beep will sound at the end of each lap.
15.0 From the main time screen, use the MODE button to toggle to CHRO. Wait 3
seconds to enter the option.
15.1 Select either GPS or the INDOOR setting.
15.2 The screen will then scroll through a battery capacity reminder screen (% of battery life left) as well as a memory reminder screen (how many hours of memory left to record)
15.3 Press the ST/STP/+ button to start the timer. Then press the VIEW/LAP button to start recording individual laps. Each lap time will be displayed for 10 seconds together with the memory number for that lap. As each lap is recorded, the total elapsed time will appear at the bottom and the current lap time above.
15.4 To pause and un-pause the timer, press the ST/STP/+ button. (STOP will appear on the screen when paused)
15.5 From the STOP screen screen press the VIEW/LAP button to review your data before
USER MANUAL NAVBIKE-GPS
13 | P a g e
saving. The screen view combinations are as follows: a) CHRONO / ODO / CALORIES, b) CALORIE / AVE PACE / MAX PACE and c) DISTANCE / CHRONO / STOP Once paused, press and hold the ST/STP/+ to automatically reset and save the file. (“Hold To Reset“ will be displayed
during this operation, finally by the file number the record was saved to)
GPS HINTS AND TIPS
16.0 Acquire satellite signals; To get the correct time of day and begin using your GPS watch, you have to acquire GPS signals. It may take a few seconds to a minute depending on your geographical location. Go outside to an open area away from tall buildings and trees. Orient the GPS antenna towards the sky for best reception. The antenna is located at the 6 o’clock position. For the first GPS sync, it is best that you stand still and do not move until completed.
16.1 Lost GPS Signal; If GPS signal is lost while in use, LOST GPS SIGNAL will appear on screen. An audible beep will also sound.
16.2 If no GPS signal has been received in 15 minutes the screen will revert back to the main time screen. The GPS search feature will also turn off.
16.3 While CHRONO is running or stopped, you can turn the GPS signal ON/OFF. The CHRONO timer however will not stop running.
DATA MODE
17.0 From the main time screen, use the MODE button to toggle to DATA.
17.1 Use the ST/STP/+ button to choose between the data records for the RUN feature. Each record has its own flashing record number. Press the VIEW/LAP button to confirm your choice.
17.2 After entering a record press ST/STP/+ button again to scroll through the following screen views. (Press the MODE button to exit when ready)
i) Start Time / End Time / Distance ii) Chrono / Distance / Calorie iii) Chrono/ Ave Speed / Max Speed v) Lap 1 / Lap Distance / Lap time vi) VIEW (Return back to memory screen) / DEL / DEL ALL
Note: To delete one file or all files, highlight the option and press and hold the VIEW/LAP button.
USER MANUAL NAVBIKE-GPS
14 | P a g e
Note: If no data is recoded, “DATA - - - -“ will be displayed.
17.3 The recorded files referenced on the main data screen data are shown in the following format:
D05 Total number of files (in this case 5) 05 The current file 08 Month (in this case August) 01 Day (in this case Wednesday)
- 1 Recorded in either T1 or T2 time zone 04 File number of the day (in this case 4) G or H G - data with GPS, H - data without GPS
CHARGING THE BATTERY
18.0 Charge the unit overnight before using for the first time. Repeat charging times will depend on usage. It is recommended to regularly re-charge your battery every 1-2 months even if it is not it use to maintain good battery condition.
CONNECTING THE USB CABLE TO YOUR WATCH AND COMPUTER
19.0 With the 4 gold plated pins at the top of both cradle and NAVBIKE-GPS, slide the NAVBIKE-GPS into the cradle. This should require little to no force. (Note: The pins on
the cradle are spring loaded so they should all depress once the clip has attached, ensuring a firm connection. You will also hear a firm “click” sound once inserted correctly)
USER MANUAL NAVBIKE-GPS
15 | P a g e
19.1 The watch will display CHARGE and the percentage charge level of the battery when connected to a USB power source. There is also a scrolling line in the middle of the screen to indicate charging has begun. 100% will appear on the screen once fully charged.
19.2 Once software and drivers have been installed and when connected to a computer, PC LINK will appear on screen.
Note 1: Please thoroughly dry the charging contacts and surrounding area to ensure proper electrical contact and to prevent corrosion. Note 2: You cannot turn the GPS function on when the battery is too low. The watch will display LOW BATT accordingly. You need to recharge the battery in order to use the GPS function again. If the battery is too low and you are exercising, your data may not be saved. Please make sure the battery has enough battery power before beginning your exercise in order not to lose your data. When the battery level becomes too low, the watch display will automatically turn OFF so as to not drain the battery further.
USING THE PC LINK SOFTWARE (QUICK START GUIDE)
20.0 This watch comes with PC software to provide communication between your watch and your PC – easily and conveniently.
20.1 Please install the driver and software onto your PC using the CD provided
20.2 Run the software (usually by double clicking the icon produced on the desktop, pending your software and installation selections)
20.3 Connect your NAVBIKE-GPS to the cradle then connect to opposite USB end to your PC
20.4 Click the download button from the main screen, to begin the download and confirm your choice by clicking the following “DOWNLOAD DATA” window.
20.5 Once the download is completed, you will be prompted to delete the recorded files from your watch. This option is at the user discretion.
20.6 Press the ENTER button to view the data.
20.7 The home page for the software will then appear, allowing you to access recorded files through to user settings.
20.8 When a recorded file is selected, the software main page will appear, giving you access to such features as Lap, Week and Monthly data, Google mapping and way points through to Deleting and backing up files, recovering files and user settings.
USER MANUAL NAVBIKE-GPS
16 | P a g e
Time Zone Table
FAQ
Q. I cannot get a GPS signal
A. Take your NAVBIKE-GPS outdoors and away from trees and tall buildings. Remain stationary and try acquiring the GPS signal again. Initially, try and ensure the antenna is pointing towards the sky for better signal reception.
Q. Can I reset the NAVBIKE-GPS?
A. You can reset your NAVBIKE-GPS watch by pressing all 4 buttons at once until the reset screen is displayed.
Q. Will my data and personal settings be lost after reset?
A. Your data and personal settings are saved in the flash memory and will not be lost after resetting.
Q. The battery indicator does not seem to be accurate
A.
Allow your
NAVBIKE
-
GPS
to fully discharge
and then fully charge it without interruption. It is recommended to regularly re-charge your battery every 1-2 months even if it is not used to maintain good battery condition.
For further product information and instruction please visit our product web page at
www.laserco.net or email support@laserco.com.au
USER MANUAL NAVBIKE-GPS
17 | P a g e
Please note: As continual improvements are made to this product, slight operational differences may occur. For the most up-to-date user manual, please visit our web site.
Warranty Against Defects
Laser Corporation Pty Ltd (“Laser”) warrants your new product to be free from defects in materials and workmanship for 12 months, from the date of purchase, provided that the product is used in accordance with accompanying recommendations or instructions where provided. The benefit of this warranty is in addition to your rights under the Australian Consumer Law and to other rights and remedies of the consumer under a law in relation to the goods or services to which the warranty relates. Through a network of retailers and resellers, Laser will provide you with your choice of a refund, repair or exchange (where possible) for this product if it becomes defective within the warranty period. This warranty will no longer apply where the defect is a result of alteration, accident, misuse, abuse, normal wear and tear, neglect or improper storage. Please retain your receipt as proof of purchase How to make a product warranty claim: Step 1: Find your receipt which proves the date of purchase. Where the date of purchase cannot be verified, your place of purchase or Laser will make an assessment based on the date of manufacture, the condition of the Laser Product and the type of defect. Step 2a): Contact your place of purchase. They will assess the nature of the fault and refund or replace the product as per their store refund or warranty policy. Step 2b): If your place of purchase cannot be contacted, then you can contact Laser . Customer Service with details of your defective Laser Product: Phone: (02) 9870 3355; or Email: service@laserco.com.au or online www.laserco.net/support/warranty (click on “Consumers (End Users)”). Our business address is at 1/6-8 Byfield Street, North Ryde, NSW 2113 Step 3: Laser . will issue you with a Return Authorisation (RA) number within 48 hours. When requested, send us the defective Product and a copy of your receipt. Laser will cover the cost of the return delivery. Step 4: Wait for us to contact you. Once we have received your defective Laser Product for inspection, we will inform you of our assessment of your claim within 7 days. When we contact you, we will firstly let you know whether you have a valid claim under this Warranty, and if so, we will inform you whether your defective Laser Product will be replaced or repaired, together with the number of days you can expect to wait to receive your replaced or repaired Laser Product. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Loading...