No part of this User’s Manual may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including photocopying recording ,for any purpose other
than the purchaser’s personal use, without the written permission of Compass Systems Corp.
Information in this User’s Manual is subject to change without notice. Compass Systems
Corp. reserves the right to change or improve or modify its products and to make changes to
the content without obligation to notify any person or organization of such changes.
Navibe is designed for outdoors navigation in the temperature range of -20°C~ 60°C.
Because of the built-in battery, please don’t heat or leave the receiver in high temperature environment or
direct sunshine for a long period of time.
Introduction section gives you a general overview of Navibe features.
Reference section tells how to operate the unit correctly and how to connect this unit to
your pocket PC step-by-step.
------
------
Navibe Bluetooth GPS Receiver!!
Navibe Bluetooth GPS Receiver
it can be your best friend!
it can be your best friend!
iv
If you find something missing or damaged with the reference to the standard package,
please contact the local dealer or retailer.
Chapter IIntroduction
i
Section 1Announcement
Section 2Warningsii
Section 3Cautioniii
Section 4Welcome to Navibeiv
Section 5Table of Contentsv
Chapter IIReference
Introduction
Section 1Hardware Description1
Section 2State Table of LED2
Section 3Operation 3-4
Section 4Packet PC Setup5-9
Section 5Pair GB337 to your Packet PC 10-14
Appendix FCC statement
v
Reference
Section 1..
Section 1
Hardware Description
Hardware Description
Hardware Description
1
Reference
Section 22. .
Section
GPS Status LED (
Battery Status LED ( Red and Orange )
State Table of LED
State Table of LED
Green)
Description
Looking for SatellitesGreen ON
Satellites lucked Green Flashing
Description
Low Power Red ON
ChargingOrange ON
Bluetooth Status LED (Blue)
Bluetooth ConnectedBlue Flashing
Wait for Bluetooth pairingBlue ON
Battery ChargedLED OFF
Description
2
Reference
Section 3. Operation --11
Section 3. Operation
To turn on the receiver, press the power buttons on
Turn on
Turn off
side for a few seconds until the GREEN GPS LED
& BLUE Bluetooth LED indicators switch on.
1) To turn off the receiver, press the power switch
on side for a few seconds until BLUE Bluetooth
LED indicators switch off.
2) Auto power-off if Bluetooth is not connected to
and host devices within 10 minutes for powersaving.
The receiver will look for satellites automatically
3
Satellite Status
once power on and indicate the status by LED
status.
Section 3. Operation --22
Section 3. Operation
You may start to pair the receiver to a Bluetooth device
when the LED indicator steady ON. When successfully
Reference
Bluetooth
Device
Low
Power
Charging
Quick Shut
Off
connected to a Bluetooth device, the Bluetooth indicator
will flash regularly.
Make sure your Pocket PCs are ready for Bluetooth
connections before device pairing.
When the power becomes low, the mini-USB power jack
allows you to connect the device to a power source to
recharge the internal battery. When fully charged, the
indicator will auto switch off.
To shut off the system rapidly when it responds slowly.
4
Reference
Section 4
Section 4
. Pocket PC Setup
. Pocket PC Setup
Pocket PC Setup
5
1. Tap the “Bluetooth” icon on screen.2. Select “Bluetooth Manager”
Section 4
Section 4
. Pocket PC Setup
. Pocket PC Setup
Reference
Note: :
Note
connecting to your Pocket PC..
connecting to your Pocket PC
Make sure
Make sure
Pocket PC Setup
BT receiver is in pairing mode
BT receiver is in pairing mode
before
before
3. Tap the “New” & “Connect!” in My
Shortcuts screen.
4. Select “Explore a Bluetooth device”
& tap “Next” in Connection Wizard
screen
6
Reference
Section 4
Section 4
. Pocket PC Setup
. Pocket PC Setup
Pocket PC Setup
7
5. Follow the instruction or await for a while.6. Tap “BT GPS V30” to continue.
Reference
Section 4
Section 4
. Pocket PC Setup
. Pocket PC Setup
Pocket PC Setup
7. Select “SPP Slave” service and tap “Next”.8. Tap “Finish” to close this program.
8
Reference
Section 4
Section 4
. Pocket PC Setup
. Pocket PC Setup
Pocket PC Setup
9
9. Tap “Connect” to activate the
connection in My Shortcuts screen.
10. Key in the Passkey “0000” then tap
“OK”
Section 5. Pair GB337 to your Pocket
Section 5. Pair GB337 to your Pocket
PC
PC
Pocket PC Setup
Note: :
Note
ON
ON
Make sure your
Make sure your
before device pairing.
before device pairing.
Pocket PC
Pocket PC
Bluetooth connection
Bluetooth connection
is
is
Reference
1. Tap the “Bluetooth” icon on main screen.2. Select “Bluetooth Manager”
10
Reference
Section 5. Pair GB337 to your Pocket
Section 5. Pair GB337 to your Pocket
PC
PC
Pocket PC Setup
11
3. Tap “Tools” then select “Paired
4. Tap “Add”
devices” in My Shortcuts screen.
Section 5. Pair GB337 to your Pocket
Section 5. Pair GB337 to your Pocket
PC
PC
Reference
3. Tap icon to look up Bluetooth
devices.
4. Tap the device ID name “BT GPS V30”
to continue.
12
Reference
Section 5. Pair GB337 to your Pocket
Section 5. Pair GB337 to your Pocket
PC
PC
13
5. Key in the passkey “
pairing.
0000” to start
6. Adding BT GPS V30 to device list.
Section 5. Pair GB337 to your Pocket
Section 5. Pair GB337 to your Pocket
PC
PC
Reference
7. You may find the BT GPS V30 in
the Paired devices screen.
14
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to
operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Compass Systems Corp. Tel: +886-2-8751-8598 Fax: +886-2-8797-3898 Email: