2015 | nativetrails.net
PRODUCT INSTALLATION INSTRUCTIONS
TABLE OF CONTENTS
A. General Installation Notes
B. Drop-In and Raised Profile Sink Installation
C. Undermount Sink Installation
D. Vessel Sink Installation
E. Apron Front Sink Installation
F. Wall Mount Vanity Installation
G. Bathtub Installation
READ THIS FIRST
A. GENERAL INSTALLATION NOTES:
• All Native Trails products should be installed by a licensed contractor
• Observe and comply with all building and plumbing codes.
• As our basins are handcrafted and dimensions are approximate, we recommend
using the actual basin for the cutout.
• Use 100% Silicone (non-water based) for all installations.
• Ensure adequate space behind the basin for faucet and backsplash,
including the full range of motion for faucet handles and spouts.
• Make sure a watertight seal exists on all drain connections.
• Do not place basin directly on floor. After unpacking, place basin on protective
material such as packing materials.
• Remember to always use non-abrasive cleaners on Native Trails sinks and tubs.
Mild soap and water is recommended. Refer to Care and Maintenance Instructions
for further information.
• If unsure which instructions pertain to your product call our Customer Service
Department at 800.786.0862. You may also view Installation and Care and Maintenance
instructions at www.nativetrails.net.
• CAUTION: Risk of personal injury. Bath tubs, large sinks, and vanities can be extremely
heavy. Obtain sufficient help to carefully lift or move.
B. DROP-IN AND RAISED PROFILE SINK INSTALLATION:
If vanity top is pre-cut go to Step 4.
DROP-IN
1. Use actual basin as your template. Place it upside down on countertop and
mark countertop by tracing edge of basin. Be sure to allow clearance for faucet
and other accessories or fixtures. *See note below for Palisades
2. Measure inside edge of lip and mark countertop accordingly, inside of the first tracing made.
3. Cut countertop midway in-between the two lines.
4. Temporarily place basin in cut-out to verify proper fit.
5. Apply silicone around cut-out in countertop, and place basin in cut-out.
6. For Raised Profile Sinks: Use wood screws from underneath the countertop and
screw into wood blocks or use silicone on wood blocks to adhere/secure to countertop.
Make sure that the screws align with the wood blocks. If the screws are not placed
properly, damage to the copper may occur.
7. Use a level to ensure that the basin is sitting level in all directions, front to back
and side to side; while pressing down to seal.
8. Carefully remove any excess silicone.
9. Install the drain according to the drain’s installation instructions.
RAISED PROFILE
*Palisades: Before cutting the countertop, turn basin over and measure from the
bottom inner edge of the apron to the front edge of the basin (approx.2.5”)
This will provide the measurement for determining where to cut and place the
basin so the apron front extends properly over the edge of the countertop.
C. UNDERMOUNT SINK INSTALLATION:
If vanity top is pre-cut go to Step 4.
UNDERMOUNT
1. Use actual basin as your template. Place it upside down on countertop and mark
countertop by tracing edge of basin. Be sure to allow clearance for faucet and
other accessories or fixtures.
2. Measure inside edge of lip and mark countertop accordingly, inside of the first line.
3. Cut countertop on inside line.
4. Temporarily place basin in cut-out to verify proper fit.
5. Apply silicone around hole in underside of countertop, and position basin.
6. Use a level to make sure that the basin is sitting level in all directions,
front to back and side to side; while pressing down to seal.
7. Copper sinks: Mounting clip fasteners may be used to secure basin under countertop
if desired. NativeStone sinks: We recommend the “Sink Undermounter Kit” from Vance
Industries, available at www.vanceind.com.These rail systems are available in four
sizes: 23” (QN23UM), 25” (QN25UM), 36” (QN36UM) and 50” (QN50UM). Please
consult with your installer to determine which system would best fit your needs.
8. Carefully remove any excess silicone.
9. Install the drain according to the drain’s installation instructions.
D. VESSEL SINK INSTALLATION:
If vanity top is pre-cut go to Step 3.
VESSEL
1. Measure outside perimeter of drain opening and mark countertop.
2. Cut countertop for drain opening.
3. Place basin on top of countertop and verify that the drain flange sits down
inside of countertop so bottom of vessel is flush with the countertop.
4. Use a level to make sure that the basin is sitting level in all directions,
front to back and side to side.
5. Install the drain according to the drain’s installation instructions.
6. The hold down nut of the drain pipe will secure the basin to the
countertop. Depending on the size of the hole in the countertop,
a large washer may also be necessary.
7. A bead of clear silicone can be used to seal the vessel to the countertop, if desired.
E. APRON FRONT SINK INSTALLATION:
1. Make a template and cutout. For built-up mount, cut countertop along
the outside line of basin profile. After centering the basin and allowing for
faucets, handles and backsplashes, use a pencil to outline the basin as your
guide for the cut-out, allowing for any reveal (if desired) before the actual cutting.
Depending on the installation type, make proper cut-out in the countertop.
2. Create a custom support using 2x4’s that will adequately hold the weight
of the sink from underneath. We highly recommend using a professional
installer to install your Native Trails sink.
3. Place the sink on top of cabinet or into the cabinet front cut-out.
Apply silicone as a gasket between sink and cabinet.
4. Apply a bead of silicone around top edge of sink. Place countertop on the sink.
Make sure that it is centered properly. Remove any excess silicone from
the lip or any surfaces.
5. Install the drain according to the drain’s installation instructions. When cleaning
up after installation do not use abrasive cleaners, as they may scratch and
alter the sink surface and finish. Use warm water, a soft cloth and a non-abrasive
soap (such as dish soap) to clean the surface. Refer to Care and Maintenance
Instructions for further information.
F. WALL MOUNT VANITY INSTALLATION:
(Bordeaux, Halcyon, Harmony, etc.)
1. Check the specified height or determine desired height and determine where
studs are located in the wall. Wall mounting hardware can be found at any
major hardware store. (If no studs can be found, use heavy duty wall
mounting hardware to secure vanity to the wall.)
2. Drill holes for lag bolts that line up with wall studs and height of vanity
in the wooden French cleat provided. Make sure slanted edge will fit
correctly into the vanity.
3. Drill pilot holes in walls and through studs so that studs will not crack
when lag bolt is tightened.
4. Screw lag bolts through wooden French cleat and into the wall making
sure it is level and at the right height to support the vanity.
5. Hang vanity on the French cleat attached to the wall.
6. Install top, sink, and drain according to installation instructions.
7. For Harmony: Ensure drawers are flush and level, and that gaps are even
between drawer and vanity frame. To level drawers, adjust washer around front
screws on either side of drawer slides. Adjustments may be needed on both sides.
HARMONY SLIDES
G. BATHTUB INSTALLATION:
Before Installation:
• Unpack and inspect the tub for damage. Place on throw rug or other
protective floor covering to prevent damage to the bath or floor.
• Make sure the flooring offers adequate support for the tub, and verify
that the sub floor is flat and level.
• Ensure proper access to the final plumbing connections.
• For tub protection, position a clean drop cloth or similar material in the
bottom of the tub. Be careful not to scratch the surface of the tub.
BATHTUB INSTALLATION (CONT.):
Installation:
1. Place the tub onto an adequately supported level floor.
2. Install the drain to the bath according to the drain manufacturer’s instructions.
DO NOT connect the trap at this time.
3. With help, carefully move the tub into place.
4. Provide access to all plumbing connections to simplify future maintenance.
5. Insert the drain tailpiece into the trap.
6. Connect the trap to the drain according to the drain’s installation instructions.
7. Install the faucet valving according to the faucet manufacturer’s instructions.
8. Open the hot and cold water supplies and check all connections for leaks.
9. Fill the tub to the overflow and check for leaks.
BATHTUB INSTALLATION (CONT.):
After Installation:
• When cleaning up after installations, DO NOT USE ABRASIVE CLEANERS,
as they may scratch and change the tub surface.
• Use warm water, a soft cloth and a non-abrasive soap (such as dish soap) to clean the surface.
• Refer to the Care and Maintenance instructions for further information.
800.786.0862
Please visit nativetrails.net for more information
and to download product specifications
Loading...