National Semiconductor LP3995 Technical data

August 2004
LP3995 Micropower 150mA CMOS Voltage Regulator with Active Shutdown
LP3995 Micropower 150mA CMOS Voltage Regulator with Active Shutdown

General Description

The LP3995 linear regulator is designed to meet the require­ments of portable battery-powered applications and will pro­vide an accurate output voltage with low noise and low quiescent current. Ideally suited for powering RF/Analog devices, this device will also be used to meet more general circuit needs in which a fast turn-off is essential.
For battery powered applications the low dropout and low ground current provided by the device allows the lifetime of the battery to be maximized. The Enable(/Disable) control allows the system to further extend the battery lifetime by reducing the power consumption to virtually zero.
The Enable(/Disable) function on the device incorporates an active discharge circuit on the output for faster device shut­down. Where the fast turn-off is not required the LP3999 linear regulator is recommended.
The LP3995 also features internal protection against short­circuit currents and over-temperature conditions.
The LP3995 is designed to be stable with small 1.0 µF ceramic capacitors. The small outline of the LP3995 micro SMD package with the required ceramic capacitors can realize a system application within minimal board area.
Performance is specified for a −40˚C to +125˚C temperature range.
The device is available in micro SMD package and LLP package. For other package options contact your local NSC sales office.
The device is available in fixed output voltages in the ranges
1.5V to 3.3V. For availability, please contact your local NSC sales office.

Key Specifications

n 2.5V to 6.0V Input Range n Accurate Output Voltage; n 60 mV Typical Dropout with 150 mA Load n Virtually Zero Quiescent Current when Disabled n Low Output Voltage Noise n Stable witha1µFOutput Capacitor n Guaranteed 150 mA Output Current n Fast Turn-on; 30 µs (Typ.) n Fast Turn-off; 175 µs (Typ.)
±
75mV / 2%

Features

n 5 pin micro SMD Package n 6 pin LLP Package n Stable with Ceramic Capacitor n Logic Controlled Enable n Fast Turn-on n Active Disable for Fast Turn-off. n Thermal-overload and Short-circuit Protection n −40 to +125˚C Junction Temperature Range for
Operation

Applications

n GSM Portable Phones n CDMA Cellular Handsets n Wideband CDMA Cellular Handsets n Bluetooth Devices n Portable Information Appliances

Typical Application Circuit

20034901
© 2004 National Semiconductor Corporation DS200349 www.national.com

Block Diagram

LP3995

Pin Description

5 pin micro SMD and LLP - 6

Pin No. Symbol Name and Function
micro
SMD
A1 3 V
B2 2 GND Common Ground
C1 6 V
C3 1 V
A3 4 C
LLP
EN
OUT
IN
BYPASS
5 N/C No internal connection. There should not be any board connection to this pin.
Pad GND Ground connection.
20034902
Enable Input; Disables the Regulator when 0.4V. Enables the regulator when 0.9V
Voltage output. Connect this output to the load circuit.
Voltage Supply Input
Bypass Capacitor connection. Connect a 0.01 µF capacitor for noise reduction.
Connect to ground plane for best thermal conduction.

Connection Diagrams

micro SMD, 5 Bump Package
Top View
See NS Package Number TLA05
www.national.com 2
20034903
Connection Diagrams (Continued)
LLP- 6 Package (SOT23 Footprint)
LP3995
Top View
See NS Package Number LDE06A
20034904
www.national.com3

Ordering Information

LP3995
Output Voltage
(V)
1.5 STD LP3995ITL-1.5 LP3995ITLX-1.5
1.6 STD LP3995ITL-1.6 LP3995ITLX-1.6
1.8 STD LP3995ITL-1.8 LP3995ITLX-1.8
1.9 STD LP3995ITL-1.9 LP3995ITLX-1.9
2.1 STD LP3995ITL-2.1 LP3995ITLX-2.1
2.5 STD LP3995ITL-2.5 LP3995ITLX-2.5
2.8 STD LP3995ITL-2.8 LP3995ITLX-2.8
2.85 STD LP3995ITL-2.85 LP3995ITLX-2.85
3.0 STD LP3995ITL-3.0 LP3995ITLX-3.0
Output Voltage
(V)
1.5 (Note 2) STD LP3995ITL-1.5 LP3995ITLX-1.5
1.6 (Note 2) STD LP3995ITL-1.6 LP3995ITLX-1.6
1.8 (Note 2) STD LP3995ITL-1.8 LP3995ITLX-1.8
1.9 (Note 2) STD LP3995ITL-1.9 LP3995ITLX-1.9
2.1 (Note 2) STD LP3995ITL-2.1 LP3995ITLX-2.1
2.5 (Note 2) STD LP3995ITL-2.5 LP3995ITLX-2.5
2.8 (Note 2) STD LP3995ITL-2.8 LP3995ITLX-2.8
3.0 (Note 2) STD LP3995ITL-3.0 LP3995ITLX-3.0

For micro SMD Package

Grade LP3995 Supplied as 250
Units, Tape and Reel

For micro SMD Package unleaded

Grade LP3995 Supplied as 250
Units, Tape and Reel
LP3995 Supplied as
3000 Units, Tape and
Reel
LP3995 Supplied as
3000 Units, Tape and
Reel
Package
Marking
Package
Marking

For LLP- 6 Package

Output Voltage
(V)
1.5 STD LP3995ILD-1.5 LP3995ILDX-1.5 LO20B
1.6 STD LP3995ILD-1.6 LP3995ILDX-1.6 LO21B
1.8 STD LP3995ILD-1.8 LP3995ILDX-1.8 LO22B
1.9 (Note 2) STD LP3995ILD-1.9 LP3995ILDX-1.9 LO23B
2.1 (Note 2) STD LP3995ILD-2.1 LP3995ILDX-2.1 LO24B
2.5 (Note 2) STD LP3995ILD-2.5 LP3995ILDX-2.5 LO25B
2.8 STD LP3995ILD-2.8 LP3995ILDX-2.8 LO26B
3.0 STD LP3995ILD-3.0 LP3995ILDX-3.0 LO30B
3.3 (Note 2) STD LP3995ILD-3.3 LP3995ILDX-3.3 LO31B
Note 1: Available in sample quantities only
Note 2: For availability contact your local sales office
Grade LP3995 Supplied as 1000
Units, Tape and Reel
LP3995 Supplied as
4500 Units, Tape and
Reel
Package
Marking
www.national.com 4
LP3995

Absolute Maximum Ratings

(Notes 3, 4)
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.
Input Voltage (V
Output Voltage −0.3 to (V
Enable Input Voltage −0.3 to 6.5V
Junction Temperature 150˚C
Lead/Pad Temperature (Note 5)
micro SMD 260˚C
) −0.3 to 6.5V
IN
+ 0.3V)
IN
to 6.5V (max)

Operating Ratings (Note 3)

Input Voltage (V
Enable Input Voltage 0 to 6.0V
Junction Temperature −40 to +125˚C
Ambient Temperature Range(Note 7)
IN

Thermal Properties(Note 8)

Junction to Ambient Thermal Resistance
θ
(LLP pkg.) 88˚C/W
JA
θ
(micro SMD pkg.) 255˚C/W
JA
LLP 235˚C
Storage Temperature −65 to +150˚C
Continuous Power
Internally Limited
Dissipation(Note 7)
ESD (Note 9)
Human Body Model 2 kV
Machine Model 200V

Electrical Characteristics

Unless otherwise noted, VEN= 1.5, VIN=V and limits appearing in normal type apply for T range for operation, −40 to +125˚C. (Notes 14, 15)
Symbol Parameter Conditions Typical
V
IN
DEVICE OUTPUT: 1.5 V
V
OUT
Input Voltage 2.5 6.0 V
<
1.8V
OUT
Output Voltage Tolerance I
Line Regulation Error V
micro SMD
Load Regulation Error
LLP
Load Regulation Error
PSRR Power Supply Rejection Ratio
(Note 11)
DEVICE OUTPUT: 1.8 V
V
OUT
Output Voltage Tolerance I
OUT
<
2.5V
microSMDLine Regulation Error V
LLP
Line Regulation Error
micro SMD
Load Regulation Error
LLP
Load Regulation Error
PSRR Power Supply Rejection Ratio
(Note 11)
+ 1.0V, CIN= 1 µF, I
OUT
= 25˚C. Limits appearing in boldface type apply over the full temperature
J
= 1 mA -50 50
OUT
=(V
IN
OUT(NOM)
=1mA
I
OUT
I
=1mAto150mA
OUT
=1mAto150mA
I
OUT
f = 1 kHz, I
f = 10 kHz, I
= 1 mA -50 50
OUT
=(V
IN
=1mA
I
OUT
V
=(V
IN
=1mA
I
OUT
I
=1mAto150mA
OUT
I
=1mAto150mA
OUT
f = 1 kHz, I
f = 10 kHz, I
=1mA 55
OUT
=1mA 53
OUT
OUT(NOM)
OUT(NOM)
=1mA 55
OUT
=1mA 50
OUT
= 1 mA, C
OUT
+1.0V) to 6.0V,
+1.0V) to 6.0V,
+1.0V) to 6.0V,
OUT
) 2.5 to 6.0V
-40 to 85˚C
= 1 µF, cBP= 0.01 µF. Typical values
Limit
Min Max
-75 75
Units
mV
-3.5 3.5 mV/V
10 75
70 125
µV/mA
µV/mA
dB
−75 75
mV
−2.5 2.5 mV/V
−3.5 3.5 mV/V
10 75
80 125
µV/mA
µV/mA
dB
www.national.com5
Loading...
+ 9 hidden pages