Page 1
USER GUIDE AND SPECIFICATIONS
ni.com/manuals
DeutschFrançais
NI 6509
This document contains information about using the NI PCI-6509,
NI PXI-6509, and NI PCIe-6509 data acquisition devices with the
NI-DAQmx driver software.
Note For information about using the NI USB-6509 device, refer to the NI USB-6509
User Guide and Specifications document.
The NI 6509 is a 96-bit, high-drive digital input/output (DIO) device.
The NI 6509 features 96 TTL/CMOS-compatible digital I/O lines, 24 mA
high-drive output, digital filtering, programmable power-up states, change
detection, and a watchdog timer.
Contents
Configuration .......................................................................................... 3
Programming Devices in Software.................................................. 4
Functional Overview............................................................................... 5
Safety Information .................................................................................. 6
Electromagnetic Compatibility Guidelines............................................. 8
Related Documentation ........................................................................... 9
I/O Connector.......................................................................................... 9
Pin Assignments .............................................................................. 10
SH100-100-F Connector........................................................... 10
R1005050 Connector ................................................................ 12
Signal Descriptions.......................................................................... 13
Digital I/O ............................................................................................... 14
Static DIO on NI 6509 Devices ....................................................... 14
I/O Protection................................................................................... 14
I/O Pull-Up/Pull-Down Resistors (NI PCIe-6509 Only)................. 15
Signal Connections .......................................................................... 16
Page 2
Protecting Inductive Loads...............................................................16
Sinking and Sourcing Examples.......................................................17
Driving a Relay d 24 mA ..........................................................17
Driving a Relay > 24 mA..........................................................18
Driving an SSR..........................................................................19
Power Connections..................................................................................19
+5 V Power Available at I/O Connector ..........................................19
Disk Drive Power Connector (NI PCIe-6509 Only) ........................19
When to Use the Disk Drive Power Connector.........................19
Disk Drive Power Connector Installation .................................20
Industrial DIO Features ...........................................................................20
Digital Filtering ................................................................................20
Digital Filtering Example..........................................................21
Programmable Power-Up States.......................................................22
Change Detection .............................................................................22
Change Detection Example.......................................................23
Watchdog Timer...............................................................................23
Accessories ..............................................................................................24
Specifications...........................................................................................25
Power Requirements.........................................................................25
Digital I/O.........................................................................................25
Digital Logic Levels (NI PCI/PXI-6509).........................................26
Input Signals..............................................................................26
Output Signals (Vcc = 5 V).......................................................26
Digital Logic Levels (NI PCIe-6509)...............................................27
Input Signals..............................................................................27
Output Signals...........................................................................27
Physical Characteristics....................................................................28
Environmental ..................................................................................28
Operating Environment.............................................................28
Storage Environment.................................................................29
Shock and Vibration (NI PXI-6509 Only) ................................29
Safety................................................................................................29
Electromagnetic Compatibility.........................................................30
CE Compliance.................................................................................30
Online Product Certification.............................................................30
Environmental Management ............................................................31
Where to Go for Support .........................................................................32
NI 6509 User Guide and Specifications 2 ni.com
Page 3
Configuration
The NI PCI/PXI/PCIe-6509 devices are fully compliant with the PCI Local
Bus Specification Revision 2.2, the PXI Hardware Specification
Revision 2.1, and the PCI Express Electromechanical Specification
Revision 1.1, respectively. The PCI/PXI/PCIe system automatically
allocates all device resources, including the base address and interrupt
level. The device base address is mapped into PCI memory space. It is
not necessary to perform configuration steps after the system powers up.
Before installing the NI 6509 device, you must install the software you plan
to use with the device. Refer to the software documentation for
configuration instructions.
After you install the software and the NI 6509 device, the device appears
under the Devices and Interfaces branch of the Measurement &
Automation Explorer (MAX) configuration tree.
If the NI 6509 does not appear in MAX, use the following troubleshooting
guidelines:
•Verify that you are using the correct version of the NI-DAQmx driver
software (version 7.1 or later for the NI PCI/PXI-6509 and version 9.2
or later for the NI PCIe-6509). To download the most recent National
Instruments drivers, visit the NI Web site at
Download Software»Drivers and Updates.
ni.com and select
•Press <F5> to refresh the MAX window, or close and reopen MAX.
•Restart the computer.
•Power off and unplug the computer or chassis, and install the device
in a different slot. Refer to the DAQ Getting Started guides for
installation instructions and safety guidelines.
•
(NI PCI-6509 only) You must install the NI PCI-6509 into a slot that
provides 3.3 V. Check that the 3.3 V LED (reference designator
DS1—located on the visible edge of the underside of the installed
device) is lit. If not, check that the PC motherboard provides 3.3 V
to the PCI bus.
© National Instruments Corporation 3 NI 6509 User Guide and Specifications
Page 4
Programming Devices in Software
NI measurement devices are packaged with the NI-DAQmx driver
software, an extensive library of functions and VIs you can call from your
application software, such as LabVIEW or LabWindows
program all the features of your NI measurement devices. NI-DAQmx
provides an application programming interface (API), which is a library of
VIs, functions, classes, attributes, and properties for creating applications
for your device. NI-DAQmx also includes a collection of programming
examples to help you get started developing an application. You can
modify example code and save it in an application. You can use examples
to develop a new application or add example code to an existing
application. Refer to the DAQ Getting Started guides for more information
about NI-DAQmx.
The NI PCI/PXI-6509 uses NI-DAQmx 7.1 or later, whereas the
NI PCIe-6509 requires NI-DAQmx 9.2 or later.
To l oca te L ab VI EW an d La bWind ows/ CV I exam pl es , op en th e
NI Example Finder:
•In LabVIEW, select Help»Find Examples.
™
/CVI™, to
•In LabWindows/CVI, select Help»NI Example Finder.
Measurement Studio, Visual Basic, and ANSI C examples are in the
following directories:
•NI-DAQmx examples for Measurement Studio-supported languages
are in the following directories:
MeasurementStudio\VCNET\Examples\NIDaq
–
– MeasurementStudio\DotNET\Examples\NIDaq
•NI-DAQmx examples for ANSI C are in the NI-DAQ\Examples\
DAQmx ANSI C Dev
For additional examples, refer to the NI Developer Zone at
directory
zone.ni.com.
NI 6509 User Guide and Specifications 4 ni.com
Page 5
Functional Overview
Industrial Digital
I/O Control FPGA
I/O Connector
96 DIO 96 DIO
Flash
Memory
Configuration
Control
Data/Control
PCI/PXI/CompactPCI Bus
Port 0
Port 1
Port 2
Port 3
Port 4
Port 5
Port 6
Port 7
Port 8
Port 9
Port 10
Port 11
24 mA DIO
Transceivers
Data/Control
DIO Lines
Programmable
Power-Up States
Watchdog Timer
Digital Filtering
Change Detection
PCI Bus
Interface
10 MHz
Clock
Digital I/O
NI ASIC
Digital I/O
NI ASIC
DIO Lines
NI ASIC
48 DIO48 DIO
48 DIO
48 DIO
I/O Connector
PCI Express Bus
Watchdog Timer
Data/Control
Programmable
Power-Up States
Digital Filtering
Change Detection
EEPROM
100 MHz
Clock
DIO Lines
NI ASIC
Programmable
Power-Up States
Watchdog Timer
Digital Filtering
Change Detection
Data/Control
Figure 1 shows the key functional components of the NI PCI/PXI-6509.
Figure 2 shows the key functional components of the NI PCIe-6509.
© National Instruments Corporation 5 NI 6509 User Guide and Specifications
Figure 1. NI PCI/PXI-6509 Block Diagram
Figure 2. NI PCIe-6509 Block Diagram
Page 6
Safety Information
This section contains important safety information that you must follow
when installing and using National Instruments DIO devices.
Do not operate the device in a manner not specified in this document.
Misuse of the DIO device can result in a hazard. You can compromise
the safety protection built into the DIO device if it is damaged in any way.
If the DIO device is damaged, return it to NI for repair.
Do not substitute parts or modify the DIO device except as described in this
document. Use the DIO device only with the chassis, modules, accessories,
and cables specified in the installation instructions. You must have all
covers and filler panels installed during operation of the DIO device.
Do not operate the DIO device in an explosive atmosphere or where there
may be flammable gases or fumes.
If you need to clean the DIO device, use a soft, nonmetallic brush. Make
sure that the DIO device is completely dry and free from contaminants
before returning it to service.
Operate the DIO device only at or below Pollution Degree 2. Pollution is
foreign matter in a solid, liquid, or gaseous state that can reduce dielectric
strength or surface resistivity. The following is a description of pollution
degrees:
•Pollution Degree 1 means no pollution or only dry, nonconductive
pollution occurs. The pollution has no influence.
•Pollution Degree 2 means that only nonconductive pollution occurs in
most cases. Occasionally, however, a temporary conductivity caused
by condensation must be expected.
•Pollution Degree 3 means that conductive pollution occurs, or dry,
nonconductive pollution occurs that becomes conductive due to
condensation.
Yo u mu st in s u la te s ig na l c o n ne c t io ns f o r t h e ma xi mu m v o lt ag e f or w hi ch
the DIO device is rated. Do not exceed the maximum ratings for the DIO
device. Do not install wiring while the DIO device is live with electrical
signals. Do not remove or add connector blocks when power is connected
to the system. Avoid contact between your body and the connector block
signal when hot swapping modules. Remove power from signal lines
before connecting them to or disconnecting them from the DIO device.
NI 6509 User Guide and Specifications 6 ni.com
Page 7
Operate the DIO device at or below the measurement category1 marked
on the hardware label. Measurement circuits are subjected to working
2
voltages
and transient s t r esses (overvoltage) from t h e circuit to which they
are connected during measurement or test. Installation categories establish
standard impulse withstand voltage levels that commonly occur in
electrical distribution systems. The following is a description of installation
categories:
•Measurement Category I is for measurements performed on circuits
not directly connected to the electrical distribution system referred to
3
as MAINS
voltage. This category is for measurements of voltages
from specially protected secondary circuits. Such voltage
measurements include signal levels, special equipment, limited-energy
parts of equipment, circuits powered by regulated low-voltage sources,
and electronics.
•Measurement Category II is for measurements performed on circuits
directly connected to the electrical distribution system. This category
refers to local-level electrical distribution, such as that provided by a
standard wall outlet (for example, 115 V for U.S. or 230 V for Europe).
Examples of Measurement Category II are measurements performed
on household appliances, portable tools, and similar DIO devices.
•Measurement Category III is for measurements performed in the
building installation at the distribution level. This category refers to
measurements on hard-wired equipment such as equipment in fixed
installations, distribution boards, and circuit breakers. Other examples
are wiring, including cables, bus-bars, junction boxes, switches,
socket-outlets in the fixed installation, and stationary motors with
permanent connections to fixed installations.
•Measurement Category IV is for measurements performed at the
primary electrical supply installation (<1,000 V). Examples include
electricity meters and measurements on primary overcurrent
protection devices and on ripple control units.
1
Measurement categories, also referred to as installation categories, are defined in electrical safety standard IEC 61010-1.
2
Wor king vo ltage is t he hi ghes t rm s value of a n AC or DC volta ge th at c an oc cur acros s an y pa rti cular ins ulati on.
3
MAINS is defined as a hazardous live electrical supply system that powers equipment. Suitably rated measuring circuits may
be connected to the MAINS for measuring purposes.
© National Instruments Corporation 7 NI 6509 User Guide and Specifications
Page 8
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and
limits for electromagnetic compatibility (EMC) as stated in the product
specifications. These requirements and limits are designed to provide
reasonable protection against harmful interference when the product is
operated in its intended operational electromagnetic environment. There is
no guarantee that interference will not occur in a particular installation.
To minimize the potential for the product to cause interference to radio
and television reception or to experience unacceptable performance
degradation, install and use this product in strict accordance with the
instructions in the product documentation.
Caution The following statements contain important EMC information needed before
installing and using this product:
•This product is intended for use in industrial locations. As a result, this product may
cause interference if used in residential areas. Such use must be avoided unless the user
takes special measures to reduce electromagnetic emissions to prevent interference to
the reception of radio and television broadcasts.
•This product may become more sensitive to electromagnetic disturbances in the
operational environment when test leads are attached or when connected to a test
object.
•Emissions that exceed the regulatory requirements may occur when this product is
connected to a test object.
•Changes or modifications not expressly approved by National Instruments could void
the user’s authority to operate the hardware under the local regulatory rules.
•Operate this product only with shielded cables and accessories.
NI 6509 User Guide and Specifications 8 ni.com
Page 9
Related Documentation
The following documents contain information that you may find helpful as
you use this user guide:
• DAQ Getting Started guides—These guides describe how to install the
NI-DAQmx driver software, the DAQ device, and how to confirm that
the device is operating properly.
• NI-DAQmx Help—This help file contains information about using
NI-DAQmx to program NI devices. NI-DAQmx is the software you
use to communicate with and control National Instruments DAQ
devices.
• Measurement & Automation Explorer Help for NI-DAQmx—This
help file contains information about configuring and testing DAQ
devices using MAX for NI-DAQmx, and information about special
considerations for operating systems.
• DAQ Assistant Help—This help file contains information about
creating and configuring channels, tasks, and scales using the
DAQ Assistant.
Note Yo u ca n d ow n l oa d th e se d oc um e nt s fr o m ni.com/manuals.
I/O Connector
Caution This NI product must be operated with shielded cables and accessories to ensure
compliance with the Electromagnetic Compatibility (EMC) requirements defined in the
Specifications sectio n of this docum ent. Do not use unshielded cables or ac cessories unless
they are installed in a shielded enclosure with properly designed and shielded input/output
ports and connected to the NI product using a shielded cable. If unshielded cables or
accessories are not properly installed and shielded, the EMC specifications for the product
are no longer guaranteed.
The 100-pin high-density SCSI connector on the NI 6509 provides access
to 96 digital inputs and outputs. Use this connector to connect to external
devices, such as solid-state relays (SSRs) and LEDs. For easy connection
to the digital I/O connector, use the SH100-100-F shielded digital I/O cable
with the SCB-100 connector block, or use the R1005050 ribbon cable with
the CB-50 or CB-50LP connector block.
Caution Do not make connections to the digital I/O that exceed the maximum I/O
specifications. Doing so may permanently damage the NI 6509 device and the computer.
Refer to the Signal Descriptions and Specifications sections for information about the
maximum I/O specifications.
© National Instruments Corporation 9 NI 6509 User Guide and Specifications
Page 10
Pin Assignments
SH100-100-F Connector
Figure 3 shows the pin assignments for the SH100-100-F cable when you
connect it to the NI 6509 device. The naming convention for each pin is
PX.Y, where X is the port (P) number, and Y is the line number.
NI 6509 User Guide and Specifications 10 ni.com
Page 11
+5 V
P3.0
P0.0
P3.1
P0.1
P3.2
P0.2
P3.3
P0.3
P3.4
P0.4
P3.5
P0.5
P3.6
P0.6
P3.7
P0.7
P4.0
P1.0
P4.1
P1.1
P4.2
P1.2
P4.3
P1.3
P4.4
P1.4
P4.5
P1.5
P4.6
P1.6
P4.7
P1.7
P5.0
P2.0
P5.1
P2.1
P5.2
P2.2
P5.3
P2.3
P5.4
P2.4
P5.5
P2.5
P5.6
P2.6
P5.7
+5 V
P9.0
P6.0
P9.1
P6.1
P9.2
P6.2
P9.3
P6.3
P9.4
P6.4
P9.5
P6.5
P9.6
P6.6
P9.7
P6.7
P10.0
P7.0
P10.1
P7.1
P10.2
P7.2
P10.3
P7.3
P10.4
P7.4
P10.5
P7.5
P10.6
P7.6
P10.7
P7.7
P11.0
P8.0
P11.1
P8.1
P11.2
P8.2
P11.3
P8.3
P11.4
P8.4
P11.5
P8.5
P11.6
P8.6
P11.7
GND
P2.7
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
GND
P8.7
© National Instruments Corporation 11 NI 6509 User Guide and Specifications
Refer to the Signal Descriptions section for information about the signals
available on this connector.
Figure 3. SH100-100-F Connector Pinout
Page 12
R1005050 Connector
+5 V
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
GND
P3.1
P3.2
P3.4
P3.5
P3.6
P3.7
P3.0
P3.3
P4.0
P4.1
P4.2
P4.3
P4.4
P4.5
P4.6
P4.7
P5.0
P5.1
P5.2
P5.3
P5.4
P5.5
P5.6
P5.7
49 50
47 48
45 46
43 44
41 42
39 40
37 38
35 36
33 34
31 32
29 30
27 28
25 26
23 24
21 22
19 20
17 18
15 16
13 14
11 12
910
78
56
34
12
Positions 1 through 50
+5 V
P6.0
P6.1
P6.2
P6.3
P6.4
P6.5
P6.6
P6.7
P7.0
P7.1
P7.2
P7.3
P7.4
P7.5
P7.6
P7.7
P8.0
P8.1
P8.2
P8.3
P8.4
P8.5
P8.6
P8.7
GND
P9.1
P9.2
P9.4
P9.5
P9.6
P9.7
P9.0
P9.3
P10.0
P10.1
P10.2
P10.3
P10.4
P10.5
P10.6
P10.7
P11.0
P11.1
P11.2
P11.3
P11.4
P11.5
P11.6
P11.7
49 50
47 48
45 46
43 44
41 42
39 40
37 38
35 36
33 34
31 32
29 30
27 28
25 26
23 24
21 22
19 20
17 18
15 16
13 14
11 12
910
78
56
34
12
Positions 51 through 100
Figure 4 shows the pin assignments for the R1005050 cable when you
connect it to the NI 6509 device. The naming convention for each pin is
PX.Y, where X is the port (P) number, and Y is the line number or name.
NI 6509 User Guide and Specifications 12 ni.com
Refer to the Signal Descriptions section for information about the signals
available on this connector.
Figure 4. R1005050 Connector Pinout
Page 13
Signal Descriptions
Pin Signal Name Description MSB LSB
Table 1 lists the signals and descriptions for all signals available on the
NI 6509 device.
Table 1. NI 6509 Signal Descriptions
1, 3, 5, 7, 9, 11, 13, 15 P2.<7..0> Bi-directional data lines for
port 2
2, 4, 6, 8, 10, 12, 14, 16 P5.<7..0> Bi-directional data lines for
port 5
17, 19, 21, 23, 25, 27,
29, 31
18, 20, 22, 24, 26, 28,
30, 32
33, 35, 37, 39, 41, 43,
45, 47
34, 36, 38, 40, 42, 44,
46, 48
P1.<7..0> Bi-directional data lines for
port 1
P4.<7..0> Bi-directional data lines for
port 4
P0.<7..0> Bi-directional data lines for
port 0
P3.<7..0> Bi-directional data lines for
port 3
49, 99 +5 V supply +5 volts; provides +5 V power
source
50, 100 GND Ground; connected to the
computer ground signal
P2.7 P2.0
P5.7 P5.0
P1.7 P1.0
P4.7 P4.0
P0.7 P0.0
P3.7 P3.0
— —
— —
51, 53, 55, 57, 59, 61,
63, 65
52, 54, 56, 58, 60, 62,
64, 66
67, 69, 71, 73, 75, 77,
79, 81
68, 70, 72, 74, 76, 78,
80, 82
83, 85, 87, 89, 91, 93,
95, 97
84, 86, 88, 90, 92, 94,
96, 98
P8.<7..0> Bi-directional data lines for
port 8
P11.<7..0> Bi-directional data lines for
port 11
P7.<7..0> Bi-directional data lines for
port 7
P10.<7..0> Bi-directional data lines for
port 10
P6.<7..0> Bi-directional data lines for
port 6
P9.<7..0> Bi-directional data lines for
port 9
P8.7 P8.0
P11.7 P11.0
P7.7 P7.0
P10.7 P10.0
P6.7 P6.0
P9.7 P9.0
© National Instruments Corporation 13 NI 6509 User Guide and Specifications
Page 14
Digital I/O
Static DIO on NI 6509 Devices
The NI 6509 device provides 96 lines of bi-directional DIO signals,
P<0..11>.<0..7>. You can use each of the DIO lines as a static digital input
(DI) or digital output (DO) line. All samples of DI lines and updates of DO
lines are software-timed.
I/O Protection
Use the following guidelines to avoid electrostatic discharge (ESD) events
and fault conditions such as overvoltage, undervoltage, and overcurrent:
•If you configure a DIO line as an output, do not connect the line to any
external signal source, ground signal, or power supply.
•If you configure a DIO line as an output, understand the current
requirements of the load. Do not exceed the output limits of the
DAQ device. NI has several signal conditioning solutions for digital
applications that require high current drive.
•If you configure a DIO line as an input, do not drive the line with
voltages outside of the normal operating range.
•Treat the DAQ device as you would treat any static sensitive device.
Always properly ground yourself and the equipment when handling
the DAQ device or connecting to it.
NI 6509 User Guide and Specifications 14 ni.com
Page 15
I/O Pull-Up/Pull-Down Resistors (NI PCIe-6509 Only)
NI ASIC
Digital I/O Line
+5 V
GND
47 kΩ,
typical
4.7 kΩ, typical
Software Controlled
I/O Protection
The NI PCIe-6509 has user-configurable pull-up and pull-down resistors.
The DIO lines on the NI PCIe-6509 are connected to an NI ASIC that
contains a weak pull-down resistor (47 k:, typical), and each DIO line is
connected to a software-selectable strong pull-up resistor (4.7 k:, typical),
as Figure 5 shows.
Figure 5. NI PCIe-6509 Digital I/O Circuitry
If you set the software to pull-down, the weak pull-down resistor in the
NI ASIC pulls the DIO line low. If you set the software to pull-up, the
strong pull-up resistor pulls the DIO line high. The pull setting takes effect
regardless of the I/O direction, but the pull setting affects only the state of
the DIO lines that are configured for input.
To us e MA X t o co nfigu re t he I/ O pul l res is tor, s el ec t t he d evice a nd cl ic k
the Properties button. Refer to the software documentation for information
about how to program the pull setting using NI-DAQmx with LabVIEW or
other NI application development environments (ADEs).
© National Instruments Corporation 15 NI 6509 User Guide and Specifications
Page 16
Signal Connections
41
43
45
47
67
69
71
73
50, 100
NI 6509
+5 V
+5 V
LED
Port 7
P7<7..4>
Port 0
P0<3..0>
GND
TTL Signal
Figure 6 shows an example of signal connections for three typical
digital I/O applications. Port 0 is configured for digital output, and port 7
is configured for digital input.
Digital output applications include sending TTL signals and driving
external devices such as the LED shown in the figure. Digital input
applications include receiving TTL signals and sensing external device
states such as the state of the switch in the figure.
Protecting Inductive Loads
When inductive loads are connected to output lines, a large
counter-electromotive force may occur at switching time because of the
energy stored in the inductive load. These flyback voltages can damage
the outputs and/or the power supply.
Figure 6. NI 6509 Signal Connections
NI 6509 User Guide and Specifications 16 ni.com
Page 17
To l im it the se fly ba ck vol tag es at the inductive load, install a flyback diode
PX.Y
GND
Load
NI 6509
Flyback Diode for
Inductive Loads
PX.Y
GND
NI 6509
Vcc
across the inductive load. For best results, mount the flyback diode within
18 inches of the load. Figure 7 shows an example of using an external
flyback diode to protect inductive loads.
Figure 7. Limiting Flyback Voltages at the Inductive Load
Sinking and Sourcing Examples
The following sections provide examples of driving a relay with no more
than 24 mA, driving a relay with more than 24 mA, and driving a
solid-state relay (SSR).
Driving a Relay d 24 mA
Figures 8 and 9 show examples of connecting the NI 6509 to a relay that
does not require more than 24 mA of current.
Figure 8. NI 6509 Sinking Connection Example, d 24 mA
© National Instruments Corporation 17 NI 6509 User Guide and Specifications
Page 18
Figure 9. NI 6509 Sourcing Connection Example, d 24 mA
PX.
Y
GND
NI 6509
PX.
Y
GND
NI 6509
Vcc
PX.Y
GND
NI 6509
Vcc
Driving a Relay > 24 mA
Figures 10 and 11 are examples of connecting the NI 6509 to a relay that
requires more than 24 mA of current. These examples use an additional
transistor circuit.
Figure 10. NI 6509 Sinking Connection Example, > 24 mA
NI 6509 User Guide and Specifications 18 ni.com
Figure 11. NI 6509 Sourcing Connection Example, > 24 mA
Page 19
Driving an SSR
+
–
V
AC
SSR
PX.Y
GND
Load
Load
NI 6509
Figure 12 shows an example of connecting the NI 6509 to an SSR.
Figure 12. NI 6509 SSR Connection Example
Power Connections
+5 V Power Available at I/O Connector
Pins 49 and 99 supply +5 V power to the I/O connector. The I/O connector
power has a fuse for overcurrent protection. This fuse is not customer
replaceable. If the fuse is blown, return the device to NI for repair.
Caution Do not connect the +5 V power pin directly to ground or to any other voltage
source on any other device. Doing so may permanently damage the NI 6509 device and the
computer.
Disk Drive Power Connector (NI PCIe-6509 Only)
The disk drive power connector is a four-pin hard drive connector on the
NI PCIe-6509 that, when connected, increases the current the device can
supply on the +5 V terminal.
Note The disk drive power has a fuse for overcurrent protection. This fuse is not customer
replaceable. If the fuse is blown, the fuse LED (reference designator DS1—located on the
visible edge of the underside of the installed device) is lit. In this case, return the device to
NI for repair.
When to Use the Disk Drive Power Connector
You can install the disk drive power connector if you want to increase the
power supply on the +5 V terminal. However, it is not necessary to install
the disk drive power connector for most applications.
Refer to the Specifications section for more information about the power
requirements and power limits of the NI PCIe-6509.
© National Instruments Corporation 19 NI 6509 User Guide and Specifications
Page 20
Disk Drive Power Connector Installation
1
2
Before installing the disk drive power connector, you must install and set
up the NI PCIe-6509 as described in the DAQ Getting Started guides.
Complete the following steps to install the disk drive power connector:
1. Power off and unplug the computer.
2. Remove the computer cover.
3. Attach the PC disk drive power connector to the disk drive power
connector on the NI PCIe-6509, as Figure 13 shows.
1 Device Disk Drive Power Connector 2 PC Disk Drive Power Connector
Figure 13. Connecting to the Disk Drive Power Connector
Note
For example, consider using a disk drive power connector that is not in the same power
chain as the hard drive.
The power available on the disk drive power connectors in a computer can vary.
4. Replace the computer cover, and plug in and power on the computer.
Industrial DIO Features
The NI 6509 features digital filtering, programmable power-up states,
change detection, and a watchdog timer.
Digital Filtering
You can use the digital filtering option available on the NI 6509 to
eliminate glitches on input data. When used with change detection, digital
filtering can also reduce the number of changes to examine and process.
Yo u ca n co nfi gu re t he d ig it a l i np ut l i n es t o p as s t h ro ug h a d ig i ta l fi l te r an d
control the timing interval the filter uses. The filter blocks pulses that are
shorter than half of the specified timing interval and passes pulses that are
longer than the specified interval. Intermediate-length pulses—pulses
longer than half of the interval but less than the interval—may or may not
pass the filter.
NI 6509 User Guide and Specifications 20 ni.com
Page 21
Table 2 li st s t he p uls e wi dt hs th at th e NI 65 09 is c er tai n to pa ss a nd bl oc k.
External
Signal
Sampled
External
Signal
Filter
Clock
Sample Clock
Filtered
Signal
HHHHH
HLLHH
HLLHH
A
B
C
Table 2. NI 6509 Digital Filtering
Pulse Width Passed Pulse Width Blocked
Filter Interval
t
interval
Low Pulse High Pulse Low Pulse High Pulse
t
interval
t
interval
t
/2 t
interval
interval
/2
Yo u c a n e na bl e d ig it al f il te r in g o n a s m an y in pu t l in es a s n ec e ss a r y f o r y o u r
application. All filtered lines share the same timing interval, which ranges
from 400 ns to 200 ms on the NI PCI/PXI-6509. The NI PCIe-6509
supports only three timing intervals: 160 ns, 10.24 Ps, and 5.12 ms.
Internally, the digital filter uses two clocks: a sample clock and a filter
clock. The filter clock is generated by a counter and has a period equal to
one half of the specified timing interval. The NI 6509 samples the input
signal on each rising edge of the sample clock, but the NI 6509 recognizes
a change in the input signal only if the input signal maintains its new state
for at least two consecutive rising edges of the filter clock. The filter clock
is programmable and allows you to control how long a pulse must last to be
recognized by the NI 6509.
Digital Filtering Example
Figure 14 shows an example of digital filtering.
does not remain steadily high from one rising edge of the filter clock to the
next. In period C, the filter passes the transition because the external signal
In periods A and B, the filter blocks the glitches because the external signal
© National Instruments Corporation 21 NI 6509 User Guide and Specifications
remains steadily high. Depending on when the transition occurs, the filter
may require up to two filter clocks—one full filter interval—to pass a
Figure 14. Digital Filtering Example
Page 22
transition. The figure shows a rising (0 to 1) transition. The same filtering
applies to falling (1 to 0) transitions.
Programmable Power-Up States
You can program the DIO lines on the NI 6509 to power up at a predefined
state: input, high output, or low output. Programmable power-up states
ensure that the NI 6509 powers up in a known state.
Note On the NI PCIe-6509, the DIO lines can be pulled high or low. For more
information, refer to the I/O Pull-Up/Pull-Down Resistors (NI PCIe-6509 Only) section.
The typical response time of programmable power-up states is 400 ms for
the NI PCI/PXI-6509 and 500 ms for the NI PCIe-6509.
To us e MA X ( re co mm en ded ) to pr og ra m t he p ower- up st at es , sel ec t
the device and click the Properties button. Refer to the software
documentation for information about how to program the power-up states
using NI-DAQmx with LabVIEW or other NI application development
environments (ADEs).
Change Detection
Note Excessive change detections may affect system performance. Use digital filtering to
minimize the effects of noisy input lines.
You can program the NI 6509 to send an interrupt when a change occ urs on
any input line. The NI 6509 can monitor changes on selected input lines or
on all input lines. It can monitor for rising edges (0 to 1), falling edges
(1 to 0), or both.
When an input change occurs, the NI 6509 generates an interrupt and
notifies the software. However, the NI 6509 does not report which line
changed or if the line was rising or falling. After a change, you can read the
input lines to determine the current line states. The rate of change detection
is determined by the software response time, which varies from system to
system.
An overflow bit indicates that the NI 6509 detects an additional rising or
falling edge before the software processes the previous change.
Refer to the software documentation for information about how to set up
and implement the change detection feature.
NI 6509 User Guide and Specifications 22 ni.com
Page 23
Change Detection Example
Table 3 shows a change detection example for six bits of one port.
Table 3. Change Detection Example
Bit
7 6 5 4 3 2 1 0
Changes to detect — —
Enable rising-edge
detection
Enable falling-edge
detection
yes yes yes yes no no yes no
yes yes yes yes no no no yes
This example assumes the following line connections:
•Bits 7, 6, 5, and 4 are connected to data lines from a four-bit TTL
output device. The NI 6509 detects any change in the input data so
you can read the new data value.
•Bit 1 is connected to a limit sensor. The NI 6509 detects rising edges
on the sensor, which correspond to over-limit conditions.
•Bit 0 is connected to a switch. The NI 6509 reacts to any switch
closure, which is represented by a falling edge. If the switch closure is
noisy, enable digital filtering for this line.
In this example, the NI 6509 reports rising edges on only bit 1, falling edges
on only bit 0, and rising and falling edges on bits 7, 6, 5, and 4. The NI 6509
reports no changes for bits 3 and 2. After receiving notification of a change,
you can read the port to determine the current values of all eight lines.
However, you cannot read the lines that are confi gured for ch a n g e d etection
until a change detection interrupt occurs.
Watchdog Timer
The watchdog timer is a software-configurable feature that sets critical
output lines to predefined safe states in the event of a software failure, a
system crash, or any other loss of communication between the application
and the NI 6509.
© National Instruments Corporation 23 NI 6509 User Guide and Specifications
Page 24
After you enable the watchdog timer, if the NI 6509 does not receive
a watchdog reset software command within the time specified for the
watchdog timer, the output lines enter a user-defined safe state and remain
in that state until one of the following events occurs:
•The application disarms the watchdog timer and writes new values to
the output lines.
•The NI 6509 is reset.
•The computer is restarted.
The signal indicating an expired watchdog asserts continuously until the
application disarms the watchdog timer. After the watchdog timer expires,
the NI 6509 ignores any writes until the application disarms the watchdog
timer.
Note On the NI PCIe-6509, ports that are set to tristate cannot enter safe states of output
when the computer enters a fault condition.
Yo u ca n s et t he wa tc hd og ti me r t im eo ut p e ri o d t o s p e ci f y t he a m ou nt o f
time that elapses before the watchdog timer expires. The counter on the
32
watchdog timer is configurable up to (2
minutes) on the NI PCI/PXI-6509 and (2
– 1) u100 ns (about seven
32
– 1) u 3 2 ns (about t wo m i n utes)
on the NI PCIe-6509 before the watchdog timer expires.
Accessories
Caution This NI product must be operated with shielded cables and accessories to ensure
compliance with the Electromagnetic Compatibility (EMC) requirements defined in the
Specifications section of th is document. Do not use unshielded cables or accessori es unless
they are installed in a shielded enclosure with properly designed and shielded input/output
ports and connected to the NI product using a shielded cable. If unshielded cables or
accessories are not properly installed and shielded, the EMC specifications for the product
are no longer guaranteed.
NI offers the following products for use with the NI 6509.
Cable (Part Number) Accessory (Part Number)
SH100-100-F shielded cable (185095-xx) SCB-100 connector block (776990-01)
R1005050 ribbon cable (182762-xx) CB-50 connector block, DIN-rail mount (776164-90)
CB-50LP connector block, panel mount (777101-01)
For more information about optional equipment available from NI, refer to
the NI catalog or visit
NI 6509 User Guide and Specifications 24 ni.com
ni.com.
Page 25
Specifications
This section lists the specifications for the NI 6509. These specifications
are typical at 25 °C, unless otherwise noted.
Power Requirements
Current draw from bus during no-load condition
+5 V power available at
I/O connector (pins 49 and 99) .............. +4.0 V to +5.25 V;
Note The voltage at the I/O connector depends on the amount of current drawn from the
NI 6509.
Digital I/O
NI PCI/PXI-6509 ............................375 mA on +3.3 VDC, typical;
250 mA on +5 VDC, typical
NI PCIe-6509.................................. 550 mA on +3.3 VDC, typical
1A, maximum
Number of channels ............................... 96 I/O
Compatibility
NI PCI/PXI-6509 ............................ TTL/CMOS, single-ended GND
referenced
NI PCIe-6509.................................. TTL Schmitt Trigger/CMOS,
single-ended GND referenced
Power-on state
NI PCI/PXI-6509 ............................ Input high-Z (default),
output 1 or 0
NI PCIe-6509.................................. Input pulled up or down
(software-selectable),
output 1 or 0
Data transfers ......................................... Interrupts, programmed I/O
I/O connector.......................................... 100-pin female 0.050 series SCSI
Pull resistor (NI PCIe-6509 only)
Pull-up resistor................................ 4.7 k:, typical
Input voltage protection
(NI PCIe-6509 only) .............................. ±20 V on up to two pins,
© National Instruments Corporation 25 NI 6509 User Guide and Specifications
Pull-down resistor........................... 47 k:, typical
maximum
Page 26
Digital Logic Levels (NI PCI/PXI-6509)
250 mA
i 1=
j
¦
current sourced on channel i+
Input Signals
The maximum input logic high and output logic high voltages assume a
Vcc supply voltage of 5.0 V. Given a Vcc supply voltage of 5.0 V, the
absolute maximum voltage rating for each I/O line is – 0.5 V to 5.5 V with
respect to GND.
Level Min Max
Input voltage (Vin) 0 V Vcc
Input logic high voltage (VIH) 2 V —
Input logic low voltage (VIL) — 0.8 V
Output Signals (Vcc = 5 V)
Level Min Max
High-level output current (IOH) — –24 mA
Low-level output current (IOL) — 24 mA
Output voltage (V
Output high voltage (VOH), at –24 mA 3.7 V —
Output low voltage (VOL), at 24 mA — 0.55 V
The total current sinking/sourcing from one port cannot exceed 100 mA.
With a load, use the following equation to determine the power
consumption on a 5 V rail. In the equation, j is the number of channels
you are using to source current.
) 0 V Vcc
out
NI 6509 User Guide and Specifications 26 ni.com
Page 27
Digital Logic Levels (NI PCIe-6509)
Input Signals
Level Min Max
Input voltage (Vin) 0 V 5 V
Positive-going threshold (VT+) — 2.2 V
Negative-going threshold (VT) 0.8 V —
Delta VT hysteresis (VT+ VT) 0.2 V —
Input high current (IIH)
(V
=5V, resistors set to pull-up)
in
Input high current (IIH)
(V
=5V, resistors set to pull-down)
in
Input low current (IIL)
(V
=0V, resistors set to pull-up)
in
Input low current (IIL)
(V
=0V, resistors set to pull-down)
in
— 260 PA
— 260 PA
— –1250 PA
— 20 PA
Output Signals
Level Min Max
High-level output current (IOH) — –24 mA
Low-level output current (IOL) — 24 mA
Output voltage (V
Output high voltage (VOH), at –24 mA 3.4 V —
Output low voltage (VOL), at 24 mA — 0.78 V
The total current sinking/sourcing from one port cannot exceed 100 mA.
© National Instruments Corporation 27 NI 6509 User Guide and Specifications
) 0 V 5.5 V
out
Page 28
Without the disk drive power connector installed, the +5 V supply and the
DIO lines share the same power source. In this case, use the following
equation to determine the current available at the +5 V terminal. In the
equation, I
With the disk drive power connector installed, the current at the +5 V
terminal is supplied by an external power source. In this case, the current at
the +5 V terminal can be up to 1 A.
Physical Characteristics
Dimensions (without connectors)
NI PCI-6509 ....................................12.4 cm × 9.7 cm
NI PXI-6509 ....................................16.0 cm × 10.0 cm
NI PCIe-6509...................................14.2 cm × 10.4 cm
Weight
is the total current sourced on all DIO lines.
DIO
= 1.2 A I
I
+5V
DIO
(4.9 in. × 3.8 in.)
(6.3 in. × 3.9 in.)
(5.6 in. × 4.1 in.)
Environmental
NI PCI-6509 ....................................70.9 g (2.5 oz)
NI PXI-6509 ....................................172.9 g (6.1 oz)
NI PCIe-6509...................................95.7 g (3.4 oz)
The NI 6509 device is intended for indoor use only.
Operating Environment
Ambient temperature range ....................0 °C to 55 °C
(tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2)
Relative humidity range..........................10% to 90%, noncondensing
(tested in accordance with
IEC-60068-2-56)
Altitude ...................................................2,000 m (at 25 °C ambient
temperature)
NI 6509 User Guide and Specifications 28 ni.com
Page 29
Storage Environment
Ambient temperature range.................... –20 °C to 70 °C
(tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2)
Relative humidity range ......................... 5% to 95%, noncondensing
(tested in accordance with
IEC-60068-2-56)
Shock and Vibration (NI PXI-6509 Only)
Operational shock .................................. 30 g peak, half-sine, 11 ms pulse
(tested in accordance with
IEC-60068-2-27; test profile
developed in accordance with
MIL-PRF-28800F)
Random vibration
5 Hz to 500 Hz, 0.3 grms............... Operating
Safety
5 Hz to 500 Hz, 2.4 grms............... Nonoperating
Random vibration is tested in accordance with IEC-60068-2-64. The
nonoperating test profile exceeds the requirements of MIL-PRF-28800F,
Class 3. Random vibration is tested in accordance with IEC-60068-2-64.
The nonoperating test profile exceeds the requirements of
MIL-PRF-28800F, Class 3.
This product meets the requirements of the following standards of safety
for electrical equipment for measurement, control, and laboratory use:
•IEC 61010-1, EN 61010-1
•UL 61010-1, CSA 61010-1
Note For UL and other safety certifications, refer to the product label or the Online
Product Certification section.
© National Instruments Corporation 29 NI 6509 User Guide and Specifications
Page 30
Electromagnetic Compatibility
This product meets the requirements of the following EMC standards for
electrical equipment for measurement, control, and laboratory use:
•EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity
•EN 55011 (CISPR 11): Group 1, Class A emissions
•AS/NZS CISPR 11: Group 1, Class A emissions
•FCC 47 CFR Part 15B: Class A emissions
•ICES-001: Class A emissions
Note For the standards applied to assess the EMC of this product, refer to the Online
Product Certification section.
Note For EMC compliance, operate this device only with the SH100-100-F shielded
cable.
CE Compliance
This product meets the essential requirements of applicable European
Directives as follows:
•2006/95/EC; Low-Voltage Directive (safety)
•2004/108/EC; Electromagnetic Compatibility Directive (EMC)
Online Product Certification
To obtain product certifications and the DoC for this product, visit
ni.com/certification, search by model number or product line,
and click the appropriate link in the Certification column.
NI 6509 User Guide and Specifications 30 ni.com
Page 31
Environmental Management
⬉ᄤֵᙃѻક∵ᶧࠊㅵ⧚ࡲ⊩ ˄Ё
RoHS
˅
Ёᅶ᠋
National Instruments
ヺড়Ё⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ
(RoHS)
DŽ
݇Ѣ
National Instruments
Ё
RoHS
ড়㾘ᗻֵᙃˈ䇋ⱏᔩ
ni.com/environment/rohs_china
DŽ
(For information about China RoHS compliance, go to
ni.com/environment/rohs_china
.)
NI is committed to designing and manufacturing products in an
environmentally responsible manner. NI recognizes that eliminating
certain hazardous substances from our products is beneficial to the
environment and to NI customers.
For additional environmental information, refer to the NI and the
Environment Web page at
environmental regulations and directives with which NI complies, as well
as other environmental information not included in this document.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of the product life cycle, all products must be sent to a WEEE
recycling center. For more information about WEEE recycling centers, National
Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on
Waste E lect ric a l a n d E l ect r oni c Equ ipme n t, visi t
ni.com/environment. This page contains the
ni.com/environment/weee.
© National Instruments Corporation 31 NI 6509 User Guide and Specifications
Page 32
Where to Go for Support
The National Instruments Web site is your complete resource for technical
support. At
troubleshooting and application development self-help resources to email
and phone assistance from NI Application Engineers.
A Declaration of Conformity (DoC) is our claim of compliance with the
Council of the European Communities using the manufacturer’s
declaration of conformity. This system affords the user protection for
electromagnetic compatibility (EMC) and product safety. You can obtain
the DoC for your product by visiting
product supports calibration, you can obtain the calibration certificate for
your product at
National Instruments corporate headquarters is located at
11500 North Mopac Expressway, Austin, Texas, 78759-3504.
National Instruments also has offices located around the world to help
address your support needs. For telephone support in the United States,
create your service request at
instructions or dial 512 795 8248. For telephone support outside the United
States, contact your local branch office:
ni.com/support you have access to everything from
ni.com/certification. If your
ni.com/calibration.
ni.com/support and follow the calling
Australia 1800 300 800, Austria 43 662 457990-0,
Belgium 32 (0) 2 757 0020, Brazil 55 11 3262 3599,
Canada 800 433 3488, China 86 21 5050 9800,
Czech Republic 420 224 235 774, Denmark 45 45 76 26 00,
Finland 358 (0) 9 725 72511, France 01 57 66 24 24,
Germany 49 89 7413130, India 91 80 41190000, Israel 972 3 6393737,
Italy 39 02 41309277, Japan 0120-527196, Korea 82 02 3451 3400,
Lebanon 961 (0) 1 33 28 28, Malaysia 1800 887710,
Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466,
New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60,
Poland 48 22 328 90 10, Portugal 351 210 311 210,
Russia 7 495 783 6851, Singapore 1800 226 5886,
Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197,
Spain 34 91 640 0085, Sweden 46 (0) 8 587 895 00,
Switzerland 41 56 2005151, Taiwan 886 02 2377 2222,
Thailand 662 278 6777, Turkey 90 212 279 3031,
United Kingdom 44 (0) 1635 523545
CVI, LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the
Eagle logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at
ni.com/trademarks for other National Instruments trademarks. The mark LabWindows is used
under a license from Microsoft Corporation. Windows is a registered trademark of Microsoft
Corporation in the United States and other countries. Other product and company names mentioned
herein are trademarks or trade names of their respective companies. For patents covering
National Instruments products/technology, refer to the appropriate location: Help»Patents in your
software, the patents.txt file on your media, or the National Instruments Patent Notice
at ni.com/patents.
© 2006–2010 National Instruments Corporation. All rights reserved.
372117C-01 Jun10
Loading...