National Datacomm 4010S01 Users manual

Your Installation Guide to

IEEE 802.11b USB Wireless LAN

Version: 2.01 — March 2001

1

Table of Contents

REGULATORY INFORMATION...........................................................................2

STEP BY STEP INSTALLATION GUIDE...........................................................3

1 Install the IEEE802.11b USB WLAN Utility / Driver..........................................4

2 Install the USB Adapter......................................................................................7

3 IEEE802.11B USB WLAN UTILITY......................................................................8

4 Remove your USB Adapter ...............................................................................16

5 Uninstall the IEEE802.11b USB WLAN Utility / Driver...................................17

Copyright Statement

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any
means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the
publisher.
Windows 95/98 and Windows 2000 are trademarks of Microsoft Corp.
Pentium is trademark of Intel.
All copyright is reserved.

1

Regulatory Information

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables when
connecting to computer or peripheral devices) any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator
& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

2

Step by step Installation Guide

This section will lead you through the installation of USB Adapter and IEEE802.11b USB WLAN
software in through details. You may wish to skip to quick start guide to wireless networking.

To establish your wireless network connection, the following steps should be executed.

1. Install the software using the installation CD.

2. Install the USB Wireless LAN Adapter.

3. Install the required network protocols to communicate with your network. Most likely, you will
need the TCP / IP protocol.

The product is designed to operate in Windows 98, Windows Me, and Windows 2000. And the
installation procedure is about the same. Please follow up the installation wizard that provided by
your system to install the software. The example here is based on the Windows 98SE.

3

1 Install the IEEE802.11b USB WLAN Utility / Driver

Please install the IEEE802.11b USB WLAN Utility / Driver first before inserting the

IEEE802.11b USB Wireless LAN.

1. Insert the IEEE802.11b USB Wireless LAN installation CD into your CD-ROM drive. The
setup program will then automatically start.

2. The setup program will start and the setup screen will appear on your monitor. Select
“ Next “ to go to the next screen.

3. Please select the applications you would like to install, and click “ Next “. If you select
“ Browse User Manual “, system will prompt a message to suggest you installing the
Acrobat Reader.

4