CRUISE LINER
™
SADDLEBAG
INSTALLATION INSTRUCTIONS SADDLE BAG FRAME
TO KAWASAKI VN800B CLASSIC
Installation Kit SB102
10-111102 12/98
NATIONAL CYCLE, INC.
PO Box 15 8
May woo d, IL 601 53- 015 8 USA
708 -34 3-0 400 Fa x:7 08- 343 -06 25
E- M ai l : i nf o @n a ti o n al c yc l e. c om
ht t p: / /w w w. na t io n al c yc l e .c o m
Quality Is Reflected In Our Name
INSTALLATION OF SADDLE BAG TO FRAME
R
est the stainless steel clips attached to the outside of the bag to the lower section of the frame.
Engage the quarter turn fastener to the frame.
Push in and turn clockwise one quarter turn. There
will be a slight spring pressure against the fastener,
turn until it stops. Grap the side of the bag, wiggle
it. The bag should be firmly set. If fastener is loose,
repeat installation of bag to frame.
Saddlebag Care: Washwith a mild soap or detergent and warm water. Use a soft cloth. To remove
tar use naphtha or turpentine.
Painting: Lightly sand the surface with 600 grit
sandpaper and spray lacquer, urathane or other
paint.
Replacement Parts: Contact National Cycle, Inc.
Not to exceed 11lbs (5kg) weight per bag. Do not
exceed 80 mph (129 kph) when saddlebags are
mounted.
On some motorcycles, additional accessories can
reduce a motorcycle’s stability and safe operationg
speed. Never ride a motrocycle that exhibiits any
unsafe handling characteristics. Remove all accessories and cargo at once. Have your dealer diagnose and solve the problem before remounting
your accessories.
Rest clip on lower
section of frame
Turn clockwise one
quarter turn.
Remove the two forward screws from one
Fender Strut (Wrench,10mm).
Leave Backrest Side Support in place (if
Backrest is to be installed).
Hold appropriate Saddlebag Frame (1) in place
at Fender Strut
Thread M8 x 55 Screw (2) through front bushing,
Fender Strut, and into Fender. Place washer be-
tween Fender Strut and front Frame Bracket
bushing if Backrest is used.
Thread M8 x 55 Screw through rear bushing,
Backrest Support (if used), Fender Strut, then
into Fender.
Tighten the Saddlebag Frame Mount screws to
22 ft/lbs (3.0m-kg) (Hex Key, 6mm)
Repeat on other side.
Tools Needed
Wrench, 10mm
Hex Key Wrench, 6mm
2
1
2
Parts List
Index Description Qty.
1 Saddle Bag Frame Mount, Right 1
Saddle Bag Frame Mount, Left 1
2 Screw, M8-1.25x55 Socket Head 4
R
emove the two forward screws from one
Fender Strut (Wrench,10mm).
Leave Backrest Side Support in place (if
Backrest is to be installed).
Hold appropriate Saddlebag Frame (1) in place
at Fender Strut
Thread M8 x 55 Screw (2) through front bushing,
Fender Strut, and into Fender. Place washer be-
tween Fender Strut and front Frame Bracket
bushing if Backrest is used.
Thread M8 x 55 Screw through rear bushing,
Backrest Support (if used), Fender Strut, then
into Fender.
Tighten the Saddlebag Frame Mount screws to
22 ft/lbs (3.0m-kg) (Hex Key, 6mm)
Repeat on other side.
Tools Needed
Wrench, 10mm
Hex Key Wrench, 6mm
2
1
2
Parts List
Index Description Qty.
1 Saddle Bag Frame Mount, Right 1
Saddle Bag Frame Mount, Left 1
2 Screw, M8-1.25x55 Socket Head 4
CRUISE LINER
™
SADDLEBAG
INSTALLATION INSTRUCTIONS SADDLE BAG FRAME
TO KAWASAKI VN800B CLASSIC
Installation Kit SB102
10-111102 12/98
NATIONAL CYCLE, INC.
PO Box 15 8
May woo d, IL 601 53- 015 8 USA
708 -34 3-0 400 Fa x:7 08- 343 -06 25
E- M ai l : i nf o @n a ti o n al c yc l e. c om
ht t p: / /w w w. na t io n al c yc l e .c o m
Quality Is Reflected In Our Name
INSTALLATION OF SADDLE BAG TO FRAME
Rest the stainless steel clips attached to the outside of the bag to the lower section of the frame.
Engage the quarter turn fastener to the frame.
Push in and turn clockwise one quarter turn. There
will be a slight spring pressure against the fastener,
turn until it stops. Grap the side of the bag, wiggle
it. The bag should be firmly set. If fastener is loose,
repeat installation of bag to frame.
Saddlebag Care: Washwith a mild soap or detergent and warm water. Use a soft cloth. To remove
tar use naphtha or turpentine.
Painting: Lightly sand the surface with 600 grit
sandpaper and spray lacquer, urathane or other
paint.
Replacement Parts: Contact National Cycle, Inc.
Not to exceed 11lbs (5kg) weight per bag. Do not
exceed 80 mph (129 kph) when saddlebags are
mounted.
On some motorcycles, additional accessories can
reduce a motorcycle’s stability and safe operationg
speed. Never ride a motrocycle that exhibiits any
unsafe handling characteristics. Remove all accessories and cargo at once. Have your dealer diagnose and solve the problem before remounting
your accessories.
Rest clip on lower
section of frame
Turn clockwise one
quarter turn.
Loading...