NATIONAL CONTROLS TMM, TMM-0999M-461 User Manual
1-4
9.99S
99.9S
999S
99.9M
999M
D.O.M.
INTERVAL
D.O.B.
1-SHOT
REPEAT
RANGE
SELECT SELECT
FUNCTION
Logic Function
for D.C. Models
Polarity Shown is
3
NATIONAL CONTROLS
WEST CHICAGO,IL.60185
CORPORATION
MULTIPLE RA NGE
SOLID STATE TIMER
MODEL: TMM-0999M-461
RANGE: .01SEC.-999MIN.
TIME SELECT
7
8
9
10
11
1
2
3
4
5
6
Start
Switch
6
5
4
3
2
1 1
1
10
9
8
7
Input
PIN CONFIGURATION
Time Range Select
Time Select
Timing Light
3.70 Max
2.90
.19 Max
1.75
(2729-1)
Voltage
2.4
4
7
TIME DELAY RELAYS
Multi-Time Range/Function
TMM Series
FEATURES
100% functionally tested
●
Microprocessor controlled timing circuit
●
Five logic modes, user selectable
●
Five time ranges, user selectable
●
Easy 3-digit time cycle setting
●
●
±0.1% repeatability
●
Time cycles from 50 ms to over 16
hours
Timing light
●
Superior transient protection
●
Reinforced base locator pin
●
Flame-retardant polycarbonate housing
●
File #E59090
●
The TMM Series offers selectable multiple
time ranges and functional logic modes all
in one plug-in package.
Programming is accomplished by using
two 5-position rotary switches. One switch
selects one of five time ranges. The other
switch selects one of five operating logic
modes. A 3-digit push-button switch selects
the amount of time required for a timing
cycle.
SPECIFICATIONS
TIME DELAY
Adjustment: 3 digit push-button switch
Range: 50 ms to 999 minutes in 5 ranges
Repeatability: ±0.1%, ±.02 seconds over speci-
fied timing range
ACCURACIES
Delay On Make: ±1% of set time, plus fixed error
of 80 ms max. (40 ms typical including power-on
response time)
Interval, One shot: ±1% of set time, plus fixed
error of 35 ms max. (10 ms typical)
Delay On Break: ±1% of set time, plus fixed
error of 75 ms max. (10 ms typical)
Repeat Cycle, On Time: ±1% of set time, plus
fixed error of 35 ms max. (10 ms typical)
Repeat Cycle, Off Time: ±1% of set time, minus
error of 65 ms max. (10 ms typical)
INPUT
Operating Voltage: 24, 120, 240 VAC; 12, 24,
48 VDC ±10% (DC models have reverse polarity
protection. Unfiltered input voltage to them must
be full-wave rectified)
Power On Response: .05 sec. max.
Power Off Reset Time: .15 sec. min.
Start Switch Closure Time: .020 sec. to initiate
timing cycle; .050 sec. to reset delay during tim
-
ing cycle
Power Consumption: 2 VA max.
Frequency: 50/60 Hz
OUTPUT
Type: Relay DPDT (2 form C)
Rating: 10 A max. resistive at 240 VAC; 100 mA
at 5 VDC min. load current
Life:
Mechanical: 10,000,000 operations
Full Load: 500,000 operations
TIMING LIGHT LOGIC
Repeat Cycle: Flashing during ON time; Full On
during OFF time
Other Logic Modes: Flashing during timing; con
tinuously on after time out
PROTECTION
Transient Voltage: 12, 24, 48 V timers are pro-
tected by an 8.8 joule metal oxide varistor; 120,
240 V timers are protected by a 30 joule metal
oxide varistor
Dielectric Breakdown: 1500 VAC, RMS min. at
60 Hz between input and outputs and between
outputs
MECHANICAL
Termination: 11-pin plug
Mounting: Socket mount, part number
MSO-0011P-012
ENVIRONMENTAL
Storage Temperature: -23°C to 70°C
Operating Temperature: -23°C to 55°C
Humidity: 95% relative
TIMING
Selectable Time Ranges: .05 to 9.99 seconds;
.1 to 99.9 seconds; 1 to 999 seconds; .1 to 99.9
minutes; 1 to 999 minutes (times less than 50 ms
are not recommended due to the response time
of the mechanical relay)
Selectable Operating Logic Modes:
Repeat Cycle (50% fixed duty cycle)
Single Shot (1 shot)
Delay On Break (D.O.B.)
Interval (Intervl)
Delay On Make (D.O.M.)
PROGRAMMING
To program the timer, remove voltage from the
unit and select the operating logic mode and the
time range; use the digital switches to select the
required time (0 to 999)
Note: 1) Do not apply voltage or ground to the Start switch,
2) Switch leads should be shielded when running close to other
wires (Start switch suppled by customer)
-
ORDERING INFORMATION
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: 800-323-2593 • 630-231-5900 • FAX: 630-231-1377 • www.nationalcontrols.com
TIME RANGE 12 VDC 24 VDC 48 VDC 24 VAC 120 VAC 240 VAC
.05 sec. to 999 min. TMM-0999M-466 TMM-0999M-462 TMM-0999M-464 TMM-0999M-467 TMM-0999M-461 TMM-0999M-465
Loading...