NASdeluxe
NDL-2400R-R
NDL-2400R-S
iSCSI/NAS System
User’s Manual
Copyright and Trademark Notice
NASdeluxe and other names of NASdeluxe products are registered trademarks.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft
Corporation. Apple, iTunes and Apple OS X are registered trademarks of Apple
Computers, Inc. All other trademarks and brand names are the property of their
respective owners. Specifications are subject to change without notice.
Copyright © 2008 NASdeluxe. All rights reserved.
About This Manual
All information in this manual has been carefully v erified to en sure its correctness.
In case of an error, please provide us with your feedback. NASdeluxe reserves
the right to modify the contents of this manual without notice.
Product name: NASdeluxe NDL-2400R
Manual Version: 1.1
Release Date: April 2008
Limited Warranty
NASdeluxe guarantees all components of NASdeluxe NDL-2400R are thoroughly
tested before they leave the factory and should function normally under general
usage. In case of any system malfunctions, NASdeluxe and its local
representatives and dealers are responsible for repair without cost to the
customer if the product fails within the warranty period and under normal usage.
NASdeluxe is not responsible for any damage or loss of data deemed to be
caused by its products. It is highly recommended that users conduct necessary
back-up practices.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 4
Safety Warnings
For your safety, please read and follow the following safety warnings:
Read this manual thoroughly before attempting to set up your NDL-2400R.
Your NDL-2400R is a complicated electronic device. DO NOT attempt to
repair it under any circumstances. In the case of malfunction, turn off the
power immediately and have it repaired at a qualified service center.
Contact your vendor for details.
DO NOT allow anything to rest on the power cord and DO NOT place the
power cord in an area where it can be stepped on. Carefully place
connecting cables to avoid stepping or tripping on them.
Your NDL-2400R can operate normally under temperatures between 0°C
and 40°C, with relative humidity of 20% – 85%. Using the NDL-2400R
under extreme environmental conditions could damage the unit.
Ensure that the NDL-2400R is provided with the correct supply voltage (AC
100V ~ 240V, 50/60 Hz, 3A). Plugging the NDL-2400R to an incorrect
power source could damage the unit.
Do NOT expose the NDL-2400R to dampness, dust, or corrosive liquids.
Do NOT place the NDL-2400R on any uneven surfaces.
DO NOT place the NDL-2400R in direct sunlight or expose it to other heat
sources.
DO NOT use chemicals or aerosols to clean the NDL-2400R. Unplug the
power cord and all connected cables before cleaning.
DO NOT place any objects on the NDL-2400R or obstruct its ventilation
slots to avoid overheating the unit.
Keep packaging out of the reach of children.
If disposing of the device, please follow your local regulations for the safe
disposal of electronic products to protect the environment.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 5
Table of Content s
User’s Manual .................................................. 1
Copyright and Trademark Notice ................................................... 3
About This Manual ......................................................................... 3
Limited Warranty ........................................................................... 3
Safety Warnings ............................................................................ 4
Table of Contents .......................................................................... 5
Chapter 1: Introduction ................................................................. 9
Overview ............................................................................................... 9
Product Highlights ................................................................................. 9
File Server ........................................................................................... 9
FTP Server ........................................................................................... 9
Backup Server ..................................................................................... 9
Printer Server ...................................................................................... 9
Redundant Power Supply (NDL-2400R-R) ............................................... 10
Package Contents ................................................................................ 10
Front Panel .......................................................................................... 10
Hard Disk Trays ................................................................................... 11
Rear Panel ........................................................................................... 11
NDL-2400R-R ..................................................................................... 11
NDL-2400R-S ..................................................................................... 11
Chapter 2: Hardware Installation ................................................ 13
Overview ............................................................................................. 13
Before You Begin ................................................................................. 13
Hard Disk Installation ......................................................................... 13
Cable Connections ............................................................................... 13
Checking System Status ...................................................................... 14
System Status Normal ......................................................................... 14
Chapter 3: First Time Setup ......................................................... 15
Overview ............................................................................................. 15
NASdeluxe Setup Wizard ..................................................................... 15
LCD Operation ..................................................................................... 17
LCD Controls ...................................................................................... 17
Display Mode ..................................................................................... 18
USB Copy ................................................................................................. 18
Management Mode ............................................................................. 18
Typical Setup Procedure ...................................................................... 19
Step 1: Network Setup ........................................................................ 19
Step 2: RAID Creation ......................................................................... 19
Step 3: Create Local Users or Setup Authentication ................................. 19
Step 4: Create Folders and Set Up ACLs ................................................ 19
Step 5: Start Services ......................................................................... 20
Chapter 4: System Management .................................................. 21
Overview ............................................................................................. 21
Web Administration Interface ............................................................. 21
Menu Bar .......................................................................................... 22
Language Selection ............................................................................. 22
Status Menu ........................................................................................ 23
Product Information ............................................................................ 23
System/Service Status ........................................................................ 23
System Information ............................................................................ 24
Printer Status ..................................................................................... 24
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 6
UPS Settings ...................................................................................... 25
Wake-Up On Lan (WOL) ...................................................................... 25
Power Management ............................................................................ 26
Storage Management .......................................................................... 27
Disks Information ............................................................................... 27
S.M.A.R.T. Information ............................................................................... 27
RAID Information ............................................................................... 28
RAID Configuration ............................................................................. 29
RAID Level ............................................................................................... 29
RAID Settings ........................................................................................... 30
Creating a RAID ........................................................................................ 30
Expanding a RAID ..................................................................................... 31
Migrating a RAID ....................................................................................... 32
Deleting a RAID ........................................................................................ 32
Space Allocation ................................................................................. 33
Allocating Space for Target USB Volume ....................................................... 33
Allocating Space for iSCSI Volume ............................................................... 34
Stackable NAS ................................................................................... 35
Folder Management ............................................................................ 35
Adding Folders .......................................................................................... 36
Editing Folders .......................................................................................... 36
Deleting Folders ........................................................................................ 37
NFS Share ................................................................................................ 37
Folder Access Control List (ACL) .................................................................. 38
File System Check .............................................................................. 39
Network Management ......................................................................... 41
WAN Configuration ............................................................................. 41
LAN Configuration ............................................................................... 42
DHCP Configuration ............................................................................ 42
WLAN Configuration ............................................................................ 43
Web Services Configuration .................................................................. 44
AFP (Apple Network Setup) .................................................................. 44
NFS Setup ......................................................................................... 45
User and Group Management .............................................................. 45
Local User Configuration ...................................................................... 45
Adding Users ............................................................................................ 46
Modifying Users ......................................................................................... 47
Deleting Users .......................................................................................... 47
Local Groups Configuration .................................................................. 47
Adding Groups .......................................................................................... 48
Modifying Groups ...................................................................................... 48
Deleting Groups ........................................................................................ 48
Batch User and Group Creation ............................................................. 48
ADS/NT Configuration ......................................................................... 49
System Settings .................................................................................. 51
System Notifications ........................................................................... 51
System Logs ...................................................................................... 51
Time and Date Settings ....................................................................... 52
System Configuration Backup and Restore ............................................. 53
Reset to Factory Default Settings .......................................................... 53
Upgrading System Firmware ................................................................ 54
Change Administrator Password ............................................................ 54
Reboot and Shutdown System .............................................................. 55
Logout .............................................................................................. 55
Chapter 5: Additional Feature Setup ............................................ 57
Overview ............................................................................................. 57
FTP Server ........................................................................................... 57
Printer Server ...................................................................................... 58
Windows XP SP2 ................................................................................. 58
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 7
Windows Vista .................................................................................... 59
Chapter 6: Using the NDL-2400R ................................................. 63
Overview ............................................................................................. 63
Login Page ........................................................................................... 63
Using WebDisk .................................................................................... 63
Mapping a Client PC to the NDL-2400R ................................................ 64
Windows ........................................................................................... 64
Apple OS X ........................................................................................ 64
Mapping the NDL-2400R as an iSCSI Drive .......................................... 65
Windows 2000/XP ............................................................................... 65
Windows Vista .................................................................................... 69
File Backup .......................................................................................... 69
Nsync ............................................................................................... 69
Adding an Nsync Task ................................................................................ 70
Setting Up an Nsync Target on an Nsync Device ............................................. 70
Setting Up an Nsync Target on Another Device .............................................. 70
Designating NDL-2400R as an Nsync Target .................................................. 71
NASdeluxe Backup Utility ..................................................................... 71
Windows XP Data Backup .................................................................... 71
Windows XP Data Backup .................................................................... 72
Apple OS X Backup Utilities .................................................................. 72
Chapter 7: Tips and Tricks ........................................................... 73
USB and eSATA Storage Expansion ...................................................... 73
Adding a Spare Disk ............................................................................ 73
Target USB .......................................................................................... 73
Remote Administration ........................................................................ 74
Part I - Setup a DynDNS Account .......................................................... 74
Part II - Enable DDNS on the Router ..................................................... 74
Part III - Setting up Virtual Servers (HTTPS) .......................................... 74
Firewall Software Configuration .......................................................... 75
Replacing Damaged Hard Drives ......................................................... 75
Hard Drive Damage ............................................................................ 75
Replacing a Hard Drive ........................................................................ 75
RAID Auto-Rebuild .............................................................................. 75
Chapter 8: Troubleshooting ......................................................... 77
Forgot My Password ............................................................................ 77
Forgot My Network IP Address ............................................................ 77
Resetting NAS IP Address and Admin Password .................................. 77
Can't Map a Network Drive in Windows XP .......................................... 77
Restoring Factory Defaults .................................................................. 78
Problems with Time and Date Settings ................................................ 78
Appendix A: Product Specifications ............................................. 79
Hardware Specifications ...................................................................... 79
Software Specifications ....................................................................... 79
Appendix B: Customer Support .................................................... 81
Appendix C: RAID Basics ............................................................. 82
Overview ............................................................................................. 82
Benefits ............................................................................................... 82
Improved Performance ........................................................................ 82
Data Security ..................................................................................... 82
RAID Levels ......................................................................................... 82
RAID 0 .............................................................................................. 82
RAID 1 .............................................................................................. 82
RAID 5 .............................................................................................. 83
RAID 6 .............................................................................................. 83
RAID 10 ............................................................................................ 83
JBOD ................................................................................................ 83
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 8
Stripe Size ........................................................................................... 83
Disk Usage .......................................................................................... 83
Appendix D: Active Directory Basics ............................................ 85
Overview ............................................................................................. 85
What is Active Directory? .................................................................... 85
ADS Benefits........................................................................................ 85
Appendix E: UPS Compatibility List .............................................. 86
Appendix F: Licensing Information .............................................. 89
Overview ............................................................................................. 89
Source Code Availability ...................................................................... 89
CGIC License Terms ............................................................................. 90
GNU General Public License ................................................................. 90
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 9
Chapter 1: Introduction
Overview
Thank you for choosing the NASdeluxe NDL-2400R 1U Rackmount Storage Server.
The NASdeluxe NDL-2400R is an easy-to-use storage server that allows a
dedicated approach to storing and distributing data on a network. Data reliability
is ensured with RAID features that provide data security and recovery—over one
Terabyte of storage is available using RAID 5 and RAID 6. Gigabit Ethernet ports
enhance network efficiency, allowing the NDL-2400R to take over file
management functions, increase application and data sharing and provide faster
data response. The NDL-2400R offers data mobility with a disk roaming feature
that lets you hot swap working hard drives for use in another NDL-2400R,
securing the continuity of data in the event of hardware failure. The NDL-2400R
allows data consolidation and sharing between Windows (SMB/CIFS), UNIX/Linux,
and Apple OS X environments, and its user-friendly GUI supports multiple
languages. Take the time now to read through this user’s manual and get the
most out of your NDL-2400R.
Product Highlights
File Server
First and foremost, the NDL-2400R allows you to store and share files over an IP
network. With a Network Attached Storage (NAS) device, you can centralize your
files and share them easily over your network. With the easy-to-use web-based
interface, users on your network can access these files in a snap.
To learn about the Web User Interface, go to Chapter 6: Using the NDL-2400R
> Using WebDisk.
FTP Server
With the built-in FTP Server, friends, clients, and customers can upload and
download files to your NDL-2400R over the Internet with their favorite FTP
programs. You can create user accounts so that only authorized users have
access.
To set up the FTP Server, refer to Chapter 5: Additional Feature Setup > FTP
Server.
Backup Server
Don’t leave precious data to chance. With advanced backup capabilities, you can
easily upload mission critical files to the NDL-2400R, and even automate your
backup tasks for true peace-of-mind.
To find out how to backup your files with the NDL-2400R, refer to Chapter 6:
Using the NDL-2400R > File Backup.
Printer Server
With the NDL-2400R’s Printer Server, you can easily share an IPP printer with
other PCs connected to your network.
To set up the Printer Server, refer to Chapter 5: Additional Feature Setup >
Printer Server.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 10
Redundant Power Supply (NDL-2400R-R)
The redundant power supply included with the NDL-2400R-R ensures maximum
uptime in the event of a failure of one of the power supplies. This is
recommended for systems that require a high degree of fault tolerance.
Package Contents
Your NDL-2400R package should contain the following items:
QIG
CD-Title
Ethernet Cable
USB2.0 Cable Accessory
Screw Kit
Please check to see if your package is complete. If you find that some items are
missing, contact your dealer.
Front Panel
The NDL-2400R’s front panel displays the unit’s array of status LEDs, controls,
USB port, and LCD display. See the table below for a detailed explanation of each:
Escape Button PWR LED
Down Button LAN LED Power Button
Reset Button
Up Button USB Port
LCD Display WAN LED HDD Tray
Enter Button Busy LED
Front Panel
Item Description
WAN LED
• Solid green: network link
• Blinking green: network activity
LAN LED
• Solid green: network link
• Blinking green: network activity
Busy LED • Blinking orange: system startup or system maintenance; data
currently inaccessible
USB Port
• USB 2.0 port for compatible USB devices, such as digital
cameras, USB disks, and USB printers
Power Button • Power on/off NDL-2400R
• Solid blue: Device is powered on
• Blinking blue: eSATA hard disk is connected and active
Reset Button
• Resets the NDL-2400R
• Press for five seconds during boot process to reset I P address
and admin password
HDD Trays • Four 3.5” SATA HDD trays
• Locks are provi ded for added security
LCD Display • Displays current system status and warning messages
• Displays hostname, WAN/LAN IP address, RAID status, and
current time
Up Button
• Push to scroll up when using the LCD display
Down Button
• Push to scroll down when using the LCD display
Enter Button ↵
• Push to confirm information entered into the LCD display
Escape Button ESC • Push to leave the current LCD menu
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 11
Hard Disk Trays
Each of the NDL-2400R’s hard disk trays has a lock, a latch, and two LED
indicators:
Hard Disk Trays
Item Description
Lock • Use the lock to physically secure the hard di sk to the unit
Latch • Use to open and remove or close and secure the tray
HDD Power LED • Solid blue: hard disk i s powered on
HDD Access/Error
LED
• Blinking green: system is accessing data on the hard disk
• Blinking red: a hard disk error has occurred
Rear Panel
NDL-2400R-R
The rear panel of the NDL-2400R-R houses most of the USB and Ethernet
connections, as well as the eSATA port, system fan, and power connector. See
the table below for descriptions of each:
Power Connector Power Connector
Power Switch Power Switch USB Ports (A Type) LAN Port
Power LED Power LED System Fan eSATA Port Serial Port
USB Ports (B Type) WAN Port
NDL-2400R Back Panel
Item Description
eSATA Port • eSATA port for hi gh-speed storage expansion
USB Ports • USB 2.0 ports for compatible USB devices, such as digital
cameras, USB disks, and USB printers
WAN Port • WAN port for connecting to an Ethernet network through a
switch or router
LAN Port • LAN port that can be used for connection sharing
Power Switch • Switch for power supply
System Fan • System fan that exhausts heat from the unit
Serial Port • This port is for factory use only
Power Connector s • Connect the included power cords to these connectors
NDL-2400R-S
The rear panel of the NDL-2400R-S is similar to the NDL-2400R-R, but with a
single power connector:
Power Connector
Power Switch USB Ports (A Type) LAN Port
System Fan eSATA Port Serial Port
USB Ports (B Type) WAN Port
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 12
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 13
Chapter 2: Hardware Installation
Overview
Your NDL-2400R is designed for easy installation. To help you get started, the
following chapter will help you quickly get your NDL-2400R up and running.
Please read it carefully to prevent damaging your unit during installation.
Before You Begin
Before you begin, be sure to take the following precautions:
1. Read and understand the Safety Warnings outlined in the beginning of
the manual.
2. If possible, wear an anti-static wrist strap during installation to prevent
static discharge from damaging the sensitive electronic components on the
NDL-2400R.
3. Be careful not to use magnetized screwdrivers around the NDL-2400R’s
electronic components.
Hard Disk Installation
The NDL-2400R supports four standard 3.5” Serial ATA (SATA) hard disks. To
install a hard disk into the NDL-2400R, follow the steps below:
1. Remove a hard disk tray from the NDL-2400R.
2. Slide the new SATA hard disk into the tray and fasten the screws.
3. Insert the hard disk and tray back into the NDL-2400R until it snaps into
place and lock it with a key if desired.
4. The LED blinks green when the hard disk is accessed. If the Error LED
flashes red it signals a problem.
Cable Connections
To connect the NDL-2400R to your network, follow the steps below:
1. Connect an Ethernet cable from your network to the WAN port on the back
panel of the NDL-2400R.
NOTE
If your HDD was part of a RAID 1 or 5 array previously, it automatic ally rebuilds. If
you replace all the drives with higher capacity drives, you need to go to
Administrator login and format the drives.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 14
2. Connect the provided power cord into the universal power socket on the
back panel. Plug the other end of the cord into a surge protector socket.
Press the power supply switch to turn on the power supply.
3. Press the power button on the Front Panel to boot up the NDL-2400R.
Checking System Status
After making connections on the NDL-2400R and powering up, check whether the
system status is normal or has trouble by observing indicators on the front panel
and hard disk trays.
System Status Normal
The system status is normal if:
1. The WAN and LAN LEDs glow green (assuming both are connected).
2. The Power LED on the Front Panel glows blue.
3. The HDD Power LED on each HDD tray glows blue (assuming all disks are
installed).
4. The default IP address of the WAN port is 192.168.1.100.
NOTE
If you are installing the NDL-2400R-R, be sure to connect both power cables. If you
do not, the system will assume one power supply has failed, and an alarm will
sound. For more information, refer to Chapter 8: Troubleshootin g.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 15
Chapter 3: First Time Setup
Overview
Once the hardware is installed, physically connected to your network, and
powered on, you can configure the NDL-2400R so that it is accessible to your
network users. There are two ways to set up your NDL-2400R: using the
NASdeluxe Setup Wizard or the LCD display. Follow the steps below for initia l
software setup.
NASdeluxe Setup Wizard
The handy NASdeluxe Setup Wizard makes configuring NDL-2400R a snap. To
configure the NDL-2400R using the Setup Wizard, perform the following steps:
1. Insert the installation CD into your CD-ROM drive (t he host PC must be
connected to the network).
2. The Setup Wizard should launch automatically. If not, please browse your
CD-ROM drive and double click on Setup.exe.
3. The Setup Wizard will start and automatically detect all NASdeluxe storage
devices on your network. If none are found, please check your connection
and refer to Chapter 8: Troubleshooting for assistance.
4. Select the NDL-2400R that you like to configure.
NOTE
For MAC OS X users, double click on NASdeluxe Setup Wizard 1.1.6.dmg
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 16
5. Login with the administrator account and password. The default account
and password are both “admin”.
6. Name your NDL-2400R and configure the network IP address. If your
switch or router is configured as a DHCP Server, configuring th e NDL2400R to automatically obtain an IP address is recommended. You may
also use a static IP address and enter the DNS Server address manually.
7. Change the default administrator password.
8. Finished! Access the NDL-2400R Web Administrator Interface by pressing
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 17
the Start Browser button. You can also configure another NDL-2400R at
this point by clicking the Setup Other Device button. Press Exit to exit
the wizard.
LCD Operation
The NDL-2400R is equipped with an LCD on the front for easy status display and
setup. There are four buttons on the front panel to control the LCD functions.
LCD Controls
Use the Up (▲), Down (▼), Enter (↵) and Escape (ESC) keys to select various
configuration settings and menu options for NDL-2400R configuration.
The following table illustrates the keys on the front control panel:
LCD Controls
Icon Function Description
▲
Up Button Select the previous configuration settings option.
▼
Down Button Select the next configuration settings option.
↵
Enter Enter the selected menu option, sub-menu, or parameter setting.
ESC Escape Escape and return to the previous menu.
There are two modes of operation for the LCD: Display Mode and Management
Mode.
NOTE
The NASdeluxe Setup Wizard is designed for installation on systems
running Windows XP/2000 or Mac OSX or later. Users with other
operating systems will need to install the NASdeluxe Setup Wizard on a
host machine with one of these operating systems before using the
unit.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 18
Display Mode
During normal operation, the LCD will be in Display Mode.
Display Mode
Item Description
Host Name Current host name of the system.
WAN Current WAN IP setting.
LAN Current LAN IP setting.
Disk Info Current status of disk slot has been installedh
RAID Current RAID status.
System Fan Current system fan status.
CPU Fan Current CPU fan status
2006/06/16 12:00 Current system time.
The NDL-2400R will rotate these messages every one-tw o second s on the LCD
display.
USB Copy
The USB Copy function enables you to copy files stored on USB devices such as
USB disks and digital cameras to the NDL-2400R with a press of a button. To use
USB copy, follow the steps below:
1. Plug your USB device into an available USB port on the Front Panel.
2. In Display Mode, press the Down Button (▼).
3. The LCD will display “USB Copy?”
4. Press Enter (
↵) and the NDL-2400R will start copying USB disks
connected to the front USB port.
5. All of data will be copied into system folder named “USBcopy”.
Management Mode
During setup and configuration, the LCD will be in Management Mode.
To enter into Management Mode, press Enter (
↵) and an “Enter Password”
prompt will show on the LCD.
At this time, the administrator has to enter the correct LCD password. System will
check whether the correct LCD password has been entered. The default LCD
password is “0000”. If correct password is entered, you will enter into the
Management Mode menu.
Management Mode
Item Description
WAN Setting IP address and netmask of your WAN ports.
LAN Setting IP address and netmask of your LAN ports.
Link Agg. Setting Select Load Balance or Failover.
Change Admin Passwd Change administrator’s password for LCD operation.
Reset to Default Reset system to factory defaults.
Exit Exit Management Mode and return to Display Mode.
NOTE
You can also change your LCD password using the Web Administration
Interface by navigating to System > Administrator Password. For
more on the Web Administration Interface, see Chapter 4: System
Management.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 19
Typical Setup Procedure
From the Web Administration Interface, you can begin to setup your NDL-2400R
for use on your network. Setting up the NDL-2400R typically follows the five
steps outlined below.
For more on how to use the Web Administration Interface, see Chapter 4:
System Management > Web Administration Interface.
Step 1: Network Setup
From the Web Administration Interface, you can configure the network settings of
the NDL-2400R for your network. You can access the Network menu from the
menu bar.
For details on how to configure your network settings, refer to Chapter 4:
System Management > Network Management.
Step 2: RAID Creation
Next, administrators can configure their preferred RAID setting and build their
RAID volume. You can access RAID settings from the menu bar of the Web
Administration Interface by navigating to Storage > RAID.
For more information on configuring RAID, see Chapter 4: System
Management > RAID Configuration.
Don’t know which RAID level to use? Find out more about the different RAID
levels from Appendix C: RAID Basics.
Step 3: Create Local Users or Setup Authentication
Once the RAID is ready, you can begin to create local users for the NDL-2400R,
or choose to setup authentication protocols such as Active Directory (AD).
For more on managing users, go to Chapter 4: System Management > User
and Group Management.
For more information on configuring Active Directory, see Chapter 4: System
Management > User and Group Management > ADS/NT Confi guration.
For information about the benefits of Active Directory, see Appendix D: Active
Directory Basics.
Step 4: Create Folders and Set Up ACLs
Once users are introduced into your network, you can begin to create various
folders on the NDL-2400R and control user access to each using Folder Access
Control Lists.
More information on managing folders, see Chapter 4: System Management >
Folder Management.
To find out about configuring Folder Access Control Lists, see Chapter 4: System
Management > Folder Management > Folder Access Control List (ACL).
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 20
Step 5: Start Services
Finally, you can start to setup the different services of the NDL-2400R for the
users on your network. You can find out more about each of these services by
clicking below:
SMB/CIFS
Apple File Protocol (AFP)
Network File System (NFS)
File Transfer Protocol (FTP)
Printer Server
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 21
Chapter 4: System Management
Overview
The NDL-2400R provides an easily accessible Web Administration Interface.
With it, you can configure and monitor the NDL-2400R anywhere on the network.
Web Administration Interface
Make sure your network is connected to the Internet. To access the NDL-2400R
Web Administration Interface:
1. Type the NDL-2400R’s IP address into your browser. (Default IP address is
http://192.168.1.100)
2. Login to the system using the administrator user name and password. The
factory defaults are:
User Name: admin
Password: admin
If you changed your password in the setup wizard, use the new password.
Once you are logged in as an administrator, you will see the Web
Administration Interface. From here, you can configure and monitor virtually
every aspect of the NDL-2400R from anywhere on the network.
NOTE
Your computer’s network IP address must be on the same subnet as
the NDL-2400R. If the NDL-2400R has default IP address of
192.168.1.100, your managing PC IP address must be 192.168.1.x,
where x is a number between 1 and 254, but not 100.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 22
Menu Bar
The Menu Bar is where you will find all of the information screens and system
settings of the NDL-2400R. The various settings are placed in the following
groups on the menu bar:
Menu Bar
Item Description
Status Current system status of the NDL-2400R.
Storage Information and settings for storage devices installed into the
NDL-2400R.
Network Information and settings for network connections, as well as
various services of the NDL-2400R.
Accounts Allows configuration of users and groups.
System Various NDL-2400R system settings and information.
Language Choose your preferred language here.
Moving your cursor over any of these items will display the dropdown menu
selections for each group.
In the following sections, you will find det a iled explanations of each function, and
how to configure your NDL-2400R.
Language Selection
The NDL-2400R supports multiple languages,
including:
• English
• French
• German
• Italian
• Traditional Chin ese
• Simplified Chinese
• Japanese
• Korean
• Spanish
On the menu bar, click Language and the Change Language screen appears.
This screen allows you to select preferred language for the NDL-2400R.
Press Apply to confirm your selection.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 23
Status Menu
The Status Menu on the menu bar allows you to see various aspects of the NDL2400R. From here, you can discover the status of the NDL-2400R, and even find
out other details like firmware version and up time.
Product Information
Once you login, you will first see the basic
Product Information screen providing
Manufacturer, Product No., Firmware
Version, and Up Time information.
Product Information
Item Description
Manufacturer Displays the name of the system manufacturer.
Product No. Shows the model number of the system.
Firmware version Shows the current firmware version.
Up time Displays the total run time of the system.
To access this screen again, navigate to Status > About.
System/Service Status
From the Status menu, choose the System
item, and the System Status and Service
Status screens appear. These screens
provide basic system and service status
information.
System Status
Item Description
CPU Loading (%) Displays current CPU workload of the NDL-2400R.
CPU Fan Speed Displays current CPU fan status.
System Fan Speed Displays the current status of the system fan.
Up Time Shows how long the system has been running.
Service Status
Item Description
AFP Status The status of the Apple Filing Protocol server.
NFS Status The status of the Network File Service Server.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 24
SMB/CIFS Status The status of the SMB/CIFS server.
FTP Status The status of the FTP server.
Media Server The status of the Media Server
Nsync Status The status of the Nsync server.
UPnP Status The status of the UPnP service.
System Information
From Status menu, choose the Info
item, and the System Information
screen appears. You can change the
system information that appears on the
Login page by entering the new
information here and pressing Apply to
confirm.
System Information
Item Description
System Description Shows the system description that would also appear on the
Login page.
Printer Status
From the Status menu, choose the
Printer item, and the Printer
Information screen appears. This
screen provides the following
information about the USB printer
connected to the USB port.
Printer Status
Item Description
Manufacturer Displays the name of the USB printer manufacturer.
Model Displays the model of the USB printer.
Status Displays the status of the USB printer.
Remove document
from Queue
Click to remove all documents from printer queue
Restart Printer service Click to restart printer service
If a corrupt print job is sent to a printer, printing may suddenly fail. If your print
jobs seem to be locked up, pressing the Remove All Documents button to clear
the print queue may resolve the issue.
For information on how to set up the Printer Server, refer to Chapter 5:
Additional Feature Setup > Printer Server.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 25
UPS Settings
The NDL-2400R can also support various
uninterruptible power supply units,
providing extra data security and
accessibility in the case of a power failure.
From the Status menu, choose the UPS
item and the UPS Setting screen appears.
Make any changes you wish, and press
Apply to confirm changes. See the
following table for a detailed description of
each item.
UPS Settings
Item Description
UPS Monitoring Enable or disable UPS monitoring.
Manufacturer Choose the UPS manufacturer and model number
from the dropdowns.
Battery Status Current status of the UPS battery
Power Current status of the power being supplied to the
UPS
Seconds between power failure and
first notification
Delay between power failure and first notification
in seconds.
Seconds between subsequent power
failure notifications
Delay between subsequent notifications in
seconds.
Shutdown the system when the
battery charge is less than
Amount of UPS battery remaining before system
should auto-shutdown.
Apply Press Apply to save your changes.
For a list of supported UPS units, see Appendix E: UPS Compatibility List.
Wake-Up On Lan (WOL)
The NDL-2400R has the ability to be
awoken from sleep mode via WAN port.
From the Status menu, choose the WOL
item, and the Wake-up On Lan
Configuration screen appears. From here,
you can Enable or Disable.
Wake-up On Lan Configuration
Item Description
WOL Servic Enable or Disable WOL service
Apply Click Apply to save changes.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 26
Power Management
Using the NDL-2400R’s Power Management, you can save energy and money by
scheduling the NDL-2400R to turn itself on and off during certain times of the day.
From the Status menu, choose the
Power Mgmt item and the
Schedule Power On/Off screen
appears.
To designate a schedule for the NDL2400R to turn on and off, first enable
the feature by checking the Enable
Schedule Power On/Off checkbox.
Then, simply choose an on and off
time for each day of the week that
you would like to designate a
schedule by using the various
dropdowns.
Finally, click Apply to save your changes.
Example - Monday: On: 8:00; Off: 16:00
System will turn on at 8:00 AM on Monday, and off at 16:00 on Monday. System
will turn on for the rest of the week.
If you choose an on time, but do not assign an off time, the system will turn on
and remain on until a scheduled off time is reached, or if the unit is shutdown
manually.
Example - Monday: On: 8:00
System will turn on at 8:00 AM on Monday, and will not shut dow n unless
powered down manually.
You may also choose two on times or two off times on a particular day, and the
system will act accordingly.
Example - Monday: Off: 8:00; Off: 16:00
System will turn off at 8:00 AM on Monday. System will turn of f at 16:00 PM on
Monday, if it was on. If the system was already off at 16:00 PM on Monday,
system will stay off.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 27
Storage Management
The Storage Menu displays the status of storage devices installed in the NDL2400R, and includes storage configuration options such as RAID and disk settings,
folder configuration, and Nsync settings.
Disks Information
From the Storage menu, choose the Disks
item and the Disks Information screen
appears. From here, you can see various
items about installed SATA hard disks. Blank
lines indicate that a SATA hard disk is not
currently installed in that particular disk slot.
Disks Information
Item Description
Disk No. Indicates disk location.
Capacity Shows the SATA hard disk capacity.
Model Displays the SATA hard disk model name.
Firmware Shows the SATA hard disk firmware version.
Status Indicates the status of the disk. Can read OK, Warning, or
Failed.
Total Capacity Shows the total SATA hard disk capacity.
Disk Power
Management
The administrator can set the disk to power down after a period
of inactivity.
S.M.A.R.T. Information
On the Disks Information screen, the status
of each disk will be displayed in the Status
column. Clicking on an OK or Warning link
will display the S.M.A.R.T Information
window for that particular disk.
NOTE
When the Status shows Warning, it usually means there are bad sectors
on the hard disk. It is shown only as a precaution and you should
consider changing the drives.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 28
S.M.A.R.T. Information
Item Description
Tray Number Tray the hard disk is installed in.
Model Model name of the installed hard disk.
Power ON Hours Count of hours in power-on state. The raw value of this attribute
shows total count of hours (or minutes, or seconds, depending
on manufacturer) in power-on state.
Temperature Celsius The current temperature of the hard disk in degrees Celsius
Reallocated Sector
Count
Count of reallocated sectors. When the hard drive finds a
read/write/verification error, it marks this sector as "reallocated"
and transfers data to a special reserved area (spare area).
This process is also known as remapping and "reallocated"
sectors are called remaps. This is why, on a modern hard disks,
you can not see "bad blocks" while testing the surface - all bad
blocks are hidden in reallocated sectors. However, the more
sectors that are reallocated, the more a decrease (up to 10% or
more) can be noticed in disk read/write speeds.
Current Pending
Sector
Current count of unstable sectors (waiting for remapping). The
raw value of this attribute indicates the total number of sectors
waiting for remapping. Later, when some of these sectors are
read successfully, the value is decreased. If errors still occur
when reading sectors, the hard drive will try to restore the data,
transfer it to the reserved disk area (spare area), and mark this
sector as remapped. If this attribute value remains at zero, it
indicates that the quality of the corresponding surface area is
low.
Raw Read Error Rate This attribute val u e depends on read errors and disk surface
condition, and indicates the rate of hardware read errors that
occurred when reading data from a disk surface. Lower values
indicate that there is a problem with either the disk surface or
the read/write heads.
Seek Error Rate Rate of seek errors by the magnetic heads. If there is a failure
in the mechanical positioning system, servo damage or a
thermal widening of the hard disk, seek errors arise. More seek
errors indicates a worsening condition of a disk surface and the
disk mechanical subsystem.
Back Press Back to go back to the Disks Information screen.
RAID Information
From the Storage menu, choose the RAID
item and the RAID List screen appears.
This screen lists the RAID volumes currently
residing on the NDL-2400R. From this
screen, you can get information about the
status of your RAID volumes, as well as the
capacities allocated for data, USB target,
and iSCSI. There is also a graph which
represents how the RAID volume is
currently allocated.
To configure your RAID settings, press the
RAID Config button to go to the RAID Configurati on screen.
NOTE
If the Reallocated Sector Count or Current Pending Sector of a hard
disk drive is not zero, the status of the disk will show “Warning”. This
warning is only used to alert the system administrator that there are
bad sectors on the disk, and they should replace those disks as soo n as
possible.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 29
RAID Information
Item Description
Select Used to select the current RAID volume.
Master RAID The RAID volume currently designated as the Master RAID
volume.
ID ID of the current RAID volume.
NOTE: All RAID IDs must be unique.
RAID Level Shows the current RAID configuration.
Status Indicates status of the RAID. Can read either Healthy,
Degraded, or Damaged.
Disks Used Hard disks used to form the current RAID volume.
Total Capacity Total capacity of the current RAID.
Data Capacity Indicates the used capacity and total capacity used by user
data.
USB Capacity Indicates the capacity allocated to USB target mode.
iSCSI Capacity Indicates the capacity allocated to iSCSI.
RAID Config Press this to configure RAID volumes.
Space Allocation Press this to adjust the space allocated for data, USB target
mode, and iSCSI.
RAID Configuration
On the RAID List screen, press the RAID
Config button to go to the RAID
Configuration screen. In addition to RAID
disk information and status, this screen lets
you make RAID configuration settings.
For more information on RAID, see
Appendix C: RAID Basics.
RAID Level
You can set the storage volume as JBOD, RAID 0, RAID 1, RAID 5, RAID 6 or
RAID 10. RAID configuration is usually required only when you first set up the
device. A brief description of each RAID setting follows:
RAID Levels
Level Description
JBOD The storage volume is a single HDD with no RAID support. JBOD
requires a minimum of 1 disk.
RAID 0 Provides data striping but no redundancy. Improves
performance but not data safety. RAID 0 requires a minimum of
2 disks.
RAID 1 Offers disk mirroring. Provides twice the read rate of single
disks, but same write rate. RAID 1 requires a minimum of 2
disks.
RAID 5 Data striping and stripe error correction information provided.
RAID 5 requires a minimum of 3 disks. RAID 5 can sustain one
failed disk.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 30
RAID 6 Two independent parity computations must be used in order to
provide protection against double disk failure. Two different
algorithms are employed to achieve this purpose. RAID 6
requires a minimum of 4 disks. RAID 6 can sustain two failed
disks.
RAID 10 RAID 10 has high reliability and high performance. RAID 10 is
implemented as a striped array whose segments are RAID 1
arrays. It has the fault tolerance of RAID 1 and the performance
of RAID 0. RAID 10 requires 4 disks. RAID 10 can sustain two
failed disks.
RAID Settings
Using RAID Settings, you can select stripe size, choose which disks are RAID
disks or the Spare Disk, as well as enter a name for each disk.
RAID Settings
Item Description
RAID Check the boxes of the hard drives you wish to add to the
storage volume.
Master RAID Check a box to designate this as the Master RAID volume. See
the NOTE below for more information.
Disk No. Number assigned to the i n stalled hard disks.
Capacity (MB) Capacity of the installed hard disks.
Model Model number of the installed hard disks.
Status Status of the installed hard disks.
Member If this is checked, current hard disk is a part of a RAID volume.
Spare If this is checked, current hard disk is designated as a spare for
a RAID volume.
Stripe Size This sets the stripe size to maximize performance of sequential
files in a storage volume. Keep the 64K setting unless you
require a special file storage layout in the storage volume. A
larger stripe size is better for large files.
Used Percentage The percentage of the RAID volume that will be used to store
data.
Apply Press this button to configure a file system and create the RAID
storage volume.
Remove Click to remove the RAID volume. All user data, iSCSI, and
Target USB data will be removed.
Back Press this button to exit without saving changes.
Expand Press this button to configure a file system and create the RAID
storage volume.
Migration Press this button to migrate RAID level.
Creating a RAID
To create a RAID volume, follow the steps below:
1. On the RAID List screen, click New.
2. On the RAID Configuration screen, set the RAID storage space as JBOD,
RAID 0, RAID 1, RAID 5, RAID 6, or RAID 10 — see Appendix C:
RAID Basics for a detailed description of each.
3. Specify a RAID ID.
WARNING
If the administrator improperly removes a hard disk that should not be
removed when R AID status is Degraded, all data will be lost.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 31
4. If this RAID volume is meant to be the Master RAID volume, tick the
Master RAID checkbox.
5. Tick the checkboxes under the “member” heading of the hard disks you
wish to use to create a RAID.
6. Specify a stripe size — 64K is the default setting.
7. Specify the percentage allocated for user data. The remaining space will
be made available for target USB, iSCSI target.
8. Press Apply to build the RAID storage volume.
With a RAID 1, RAID 5, RAID 6, or RAID 10 volume, you can also add a spare
disk after the RAID is created. See Chapter 7: Tips and Tricks > Adding a
Spare Disk for details.
Expanding a RAID
To expand a RAID 1, RAID 5, RAID 6, or RAID 10 volume, follow the steps below:
1. Replace one of the hard drives in the RAID volume and allow it to
automatically rebuild.
2. Once rebuilt, you can continue to replace any remaining disks in the RAID
array.
3. When you are done replacing hard drives, log on to Web Management.
Navigate to Storage > RAID to open the RAID List screen.
4. On the RAID List screen, select the RAID volume by clicking on its radio
button, and click RAID Config to open the RAID Configuration screen.
5. On the RAID Configuration screen, click Expand.
NOTE
Building a RAID storage space may take time, depending on the size of
hard drives and RAID mode.
WARNING
Creating RAID destroys all data in the current RAID volume. The data is
unrecoverable.
NOTE
In a multiple RAID configuration, one RAID volume must be
designated as the Master RAID volume. The Master RAID volume will
store all installed modules. If the Master RAID is changed to another
location (i.e. assigning HDD 2 to be the Master RAID volume after
HDD 1 had been previously assigned), then all modules must be
reinstalled. In addition, all system folders that were contained on the
Master RAID vo lume will be invis ible. Reassigning this volume to be
the Master RAID will make these folders visible again.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 32
Migrating a RAID
Once a RAID volume has been created, you
may want to move it to other physical drives or
change the RAID array all together. To migrate
a RAID 0, RAID 1, or RAID 5 volume, follow
the steps below:
1. From the RAID Configuration screen,
click Migrate RAID.
2. A list of possible RAID migration
configurations will be listed. Select the
desired migration scheme and click OK.
3. The system will begin migrating the RAID volume.
Below is a table listing of possible RAID migration schemes:
To
From
RAID 0 RAID 5
RAID 0
[RAID 0] HDDx2 to [RAID 0] HDDx3
[RAID 0] HDDx2 to [RAID 0] HDDx4
[RAID 0] HDDx2 to [RAID 0] HDDx5
[RAID 0] HDDx3 to [RAID 0] HDDx4
[RAID 0] HDDx3 to [RAID 0] HDDx5
[RAID 0] HDDx4 to [RAID 0] HDDx5
[RAID 0] HDDx2 to [RAID 5] HDDx3
[RAID 0] HDDx2 to [RAID 5] HDDx4
[RAID 0] HDDx2 to [RAID 5] HDDx5
[RAID 0] HDDx3 to [RAID 5] HDDx4
[RAID 0] HDDx3 to [RAID 5] HDDx5
[RAID 0] HDDx4 to [RAID 5] HDDx5
RAID 1
[RAID 1] HDDx2 to [RAID 0] HDDx2
[RAID 1] HDDx2 to [RAID 0] HDDx3
[RAID 1] HDDx2 to [RAID 0] HDDx4
[RAID 1] HDDx2 to [RAID 0] HDDx5
[RAID 1] HDDx2 to [RAID 5] HDDx3
[RAID 1] HDDx2 to [RAID 5] HDDx4
[RAID 1] HDDx2 to [RAID 5] HDDx5
RAID 5 X
[RAID 5] HDDx3 to [RAID 5] HDDx4
[RAID 5] HDDx3 to [RAID 5] HDDx5
[RAID 5] HDDx4 to [RAID 5] HDDx5
Deleting a RAID
To delete a RAID volume, follow the steps below:
1. On the RAID List screen, select the RAID volume by clicking on its radio
button, and click RAID Config to open the RAID Configuration screen.
2. On the RAID Configuration screen, click Remove RAID.
3. The confirmation screen appear, you will have to input “Yes” with exactly
wording case to complete “Remove RAID” operation
WARNING
Removing RAID destroys all data in the current RAID volume. The data
is unrecoverable.
NOTE
Migrating a RAID volume could take several hours to complete
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 33
Space Allocation
You may specify the space allocated for both Target USB and iSCSI volumes.
To do this, under the Storage menu, click RAID and the RAID List window
appears. Select the RAID volume you wish to reallocate by clicking on its radio
button, and click Space Allocation. The RAID Information and Volume
Allocation List windows will appear.
The Volume Allocation List displays the space allocated for Target USB and
iSCSI volumes on the current RAID volume. The NDL-2400R supports up to 5
iSCSI volumes in each RAID volume.
Volume Allocation List
Item Description
Modify Click this to modify the allocated space.
Del Click this to delete the allocated space.
Type Type of volume. Can be either USB or iSCSI.
Name Name assigned to the volume.
Capacity Capacity of the allocated space.
Target USB Click to allocate space to Target USB volume.
iSCSI Target Click to allocate space to iSCSI volume.
Allocating Space for Target USB Volume
To allocate space for a Target USB volume on the current RAID volume, follow
the steps below:
1. Under the Volume Allocation List,
click Target USB.
The Create Target USB Volume
screen appears.
Create Target USB Volume
Item Description
RAID ID ID of current RAID volume.
Unused Percentage and amount of unused space on current RAID
volume.
Allocation Percentage and amount of space allocated to Target USB
volume.
OK Click OK to save changes.
Back Click Back to exit without saving.
2. Designate the percentage that should be allocated to the Target USB
volume by selecting the appropriate percentage from the Allocation
dropdown.
3. Click OK to create the Target USB volume.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 34
Allocating Space for iSCSI Volume
To allocate space for an iSCSI volume on the current RAID volume, follow the
steps below:
1. Under the Volume Allocation List, click iSCSI Target.
The Create iSCSI Volume screen appears.
Create iSCSI Volume
Item Description
RAID ID ID of current RAID volume.
Unused Percentage and amount of unused space on current RAID
volume.
Allocation Percentage and amount of space allocated to Target USB
volume.
iSCSI Target Service Enable or Disable the iSCSI Target service.
Authentication You may choose CHAP authentication or choose None.
Target Name Name of the iSCSI Target. This name will be used by the
Stackable NAS function to identify this export share.
Year Select the current year from the dropdown.
Month Select the current month from the dropdown.
Username Enter a username.
Password Enter a password.
Password Confirm Reenter the chosen password
IQN The iSCSI Qualified Name
Initiator Information Shows the name and status of iSCSI initiators logged on
the system
OK Click OK to save changes.
Back Click Back to exit without saving.
2. Designate the percentage to be allocated from the Allocation dropdown.
3. Enable the iSCSI Target Service by selecting Enable.
4. Choose to enable CHAP authentication or choose None.
5. Enter a Target Name. This will be used by the Stackable NAS function
to identify this export share.
6. Choose the current year from the Year dropdown.
7. Choose the current month from the Month dropdown.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 35
8. If you’ve enabled CHAP authentication, enter a username and a
password. Confirm your chosen password be reentering it in the
Password Confirm box.
9. Click OK to create the iSCSI volume.
Stackable NAS
The NDL-2400R’s capacity can be expanded even further using the stackable
function. With it, users can expand the capacity of their network storage systems
with up to 5 other stack target volumes which are located in different systems.
These can be stacked through single network access like SMB or AFP acting as a
share folder type.
For detailed instructions on how to use this feature, please refer to the Stackable
User Guide.
Folder Management
From the Storage menu, choose Folder,
and the Folder screen appears. This screen
allows you to create and configure folders on
the NDL-2400R volume.
Folder
Item Description
Folder name Displays the name of the folder.
Description Provides a description of the folder.
NFS Share Press NFS Share to configure which hosts on the network are
allowed to access this folder using NFS.
ACL Press ACL (Access Control List) to configure which users have
access to this folder.
Edit Press Edit to enter the Edit screen and modify the folder’s
name and description.
Del Press Del to delete the folder. A prompt appears asking to
confirm the deletion.
Add Press Add to enter the Add Folder screen.
NOTE
Nsync folders will be created once the RAID is created. Nsync folder is
used by Nsync server. It will be used for files backed up by Nsync.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 36
Adding Folders
On the Folder screen, press the Add button
and the Add Folder screen appears. This
screen allows you to add a folder. After
entering the information, press Apply to
create new folder. Press Back to return to
the Folder screen.
Add Folder
Item Description
RAID ID RAID volume where the new folder will reside.
Folder Name Enter the name of the folder.
Description Provide a description the folder.
Browseable Enable or disable users from browsing the folder contents. If
Yes is selected, then the share folder will be browseable.
Public Admit or deny public access to this folder. If Yes is selected,
then users do not need to have access permission to write to
this folder. When accessing a public folder via FTP, the behavior
is similar to anonymous FTP. Anonymous users can
upload/download a file to the folder, but they cannot delete a
file from the folder.
Share Folder Limit Enter the maximum size of the folder in Gigabytes (GB). The
folder cannot grow beyond this limit. You can enter a 0 to turn
off the share folder limit.
Apply Press Apply to create the folder.
Back Press Back to return to the Folder screen.
Editing Folders
On the Folder screen, press the Edit button and the Edit Folder screen appears.
This screen allows you to change folder information. After entering the
information, press Submit to apply the changes. Press Back to return to the
Folder screen.
Edit Folder
Item Description
Share Name Enter the name of the (Share) folder.
Comment Provide a description the folder.
Browseable Enable or disable users from browsing the folder contents. This
setting will only apply while access via SMB/CIFS and web disk.
Public Admit or deny public access to this folder.
Share Limit Enter the maximum size of the folder. The folder will not grow
beyond this limit. You can enter a 0 to turn off the share folder
limit.
Submit Press Submit to save your changes.
Back Press Back to return to the Folder screen.
NOTE
Folder names are limited to 60 characters. Systems running Windows
98 or earlier may not support file names longer than 15 characters.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 37
Deleting Folders
To delete a folder, press the Del button from the specified folder row. The system
will confirm folder deletion. Press OK to delete the folder permanently or Cancel
to go back to the folder list.
NFS Share
To allow NFS access to the share folder, enable the NFS Service, and then set up
hosts with access rights by clicking Add.
Use the following command to mount NFS shares:
mount <ip_address>:/<RAID_ID>/data/<folder_name> /<linux_path>
The share path is shown in the "Config NFS share" dialog as mount point.
For example: "mount 192.168.1.2:/raid0/data/public /home/NDL-public/"
NFS Share
Item Description
Hostname Enter the name or IP address of the host
Privilege Host has either read only or writeable access to the folder.
Guest System Support There are two selections available:
• Unix / Linux System
• AIX (Allow source port > 1024)
Choose the one which best fits your needs.
IO Mapping There are three selections available:
• Guest system root account will have full access to this
share (root:root).
• Guest system root account will be mapped to
anonymous user (nobody:nogroup) on NAS.
• All user on guest system will be mapped to anonymous
user (nobody:nogroup) on NAS.
Choose the one which best fits your needs.
Apply Click to save your changes.
Back Click to abandon changes.
WARNING
All the data stored in the folder will be deleted once the folder is
deleted. The data will not be recoverable.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 38
Folder Access Control List (ACL)
On the Folder screen, press the ACL button,
and the Access Control List screen
appears. This screen allows you to configure
access to the specific folder for users and
groups. Select a user or a group from the
left hand column and then choose Deny,
Read Only, or Writable to configure their
access level. Press the Submit button to
confirm your settings.
Access Control List
Item Description
Deny Denies access to users or groups who are displayed in this
column.
Read Only Provides Read Only access to users or groups who are displayed
in this column.
Writable Provides Write access to users or groups who are displayed in
this column.
Remove Removes the selected user or group from the column in order to
reset their access privileges.
Sync AD account Press this button when there is no list from ADS/PDC or more
ADS user has been added but yet appear from list.
Submit Submits and confirms settings.
Reset Cancel your settings and return to the Folder screen.
To configure folder access, follow the steps below:
1. On the ACL screen, all network groups and users are listed in the left hand
column. Select a group or user from this list.
2. With the group or user selected, press one of the buttons from the three
access level columns at the top. The group or user then appears in that
column and has that level of access to the folder.
3. Continue selecting groups and users and assigning them access levels
using the column buttons.
4. To remove a group or user from an access level column, press the
Remove button in that column.
5. When you are finished, press Submit to submit and confirm your ACL
settings.
NOTE
If one user has belonged to more than one group but different privilege
than the priority Deny > Read Only > Writable
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 39
The ACL screen also allows you to search for a particular user. To do this, follow
the steps below:
1. In the blank, enter the name of the user
you would like to find.
2. From the drop down select the group you
would like to search for the user in.
3. Click Search.
File System Check
The File System Check allows you to perform a
check on the integrity of your disks’ file system.
Under the Storage menu, click Filesystm Check
and the File System Check prompt appears.
To perform a file system check, click Apply.
Once clicked, the following prompt will appear:
Click Yes to reboot the system.
Once the system has rebooted, you will be returned to the File System Check
prompt. There you will see the available RAID volumes to run the file system
check on. Check the desired RAID volumes and click Next to proceed with the file
system check. Click Reboot to reboot without running the check.
Once you click Next, you will see the following screen:
NOTE
The system will list up to 1,000 users from the chosen category. To
narrow your search, enter a search term in the blank provided.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 40
Click Start to begin the file system check. Click Back to return to the previous
screen. Click Reboot to reboot the system.
When the file system check is run, the system will show 20 lines of information
until it is complete. Once complete, the results will be shown at the bottom.
NOTE
The system must be rebooted before the NDL-2400R can function
normally.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 41
Network Management
Use the Network menu to make network configuration settings as well as service
support settings.
WAN Configuration
From the Network menu, choose WAN,
and the WAN Configuration screen
appears. This screen displays the network
parameters of the WAN connection. You may
change any of these items and press Apply
to confirm your settings. See a description
of each item in the following table:
WAN Configuration
Item Description
Host name Host name that identifies the NDL-2400R on the network.
Domain name Specifies the domain name of the NDL-2400 R.
MAC Address MAC address of the network interface.
Jumbo Frame Support Enable or disabl e Jumbo Frame Support of the WAN interface on
your NDL-2400R.
DHCP Enable or disable the NDL-2400R from obtaining in IP address
via DHCP server. If you require a static IP, disable this feature
and input your network configuration.
IP IP address of the WAN interface.
Netmask
Network mask, which is generally: 255.255.255.0
Gateway Default Gateway IP address.
DNS Server Domain Name Service (DNS) server IP address.
IP Sharing Mode When enabled, PCs connected to the LAN port will be able to
access the WAN. Default is Enabled.
Link Aggregation Specifies whether WAN and LAN ports will be aggregated and
act as one port.
Failover: When one port fails, the other one will take over.
Load Balance: Ethernet traffic will flow alternative between two
Ethernet ports.
802.3ad: Linkage two Ethernet ports in parallel to increase
throughput.
NOTE
• Only use Jumbo Frame settings when operating in a Gigabit
environment where all other clients have Jumbo Frame Setting
enabled.
• Enabling DHCP automatically turns on UPnP—see the Service
Support Screen.
• If you are only using the WAN port, we suggest that you disable IP
Sharing Mode. This wi ll r es u lt in h ig h er t h ro ughput.
• A correct DNS setting is vital to networks services, such as SMTP
and NTP.
• To use the Link Aggregation with “802.3ad selected” feature,
please make sure the networking equipment on the other end of
Ethernet cable also supports 802.3ad protocol.
WARNING
Most Fast Ethernet (10/100) Switches/Routers do not support Jumbo
Frame and you will not be able to connect to your NDL-2400R after
Jumbo Frame is turned on. If this happens, turn off the NDL-2400R.
Then, power on the NDL-2400R and immediately press and hold the
Reset button on the back of the unit for 10 seconds. This will reset
your network settings, password, and turn off Jumbo Frame Support.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 42
LAN Configuration
The NDL-2400R supports two Gigabit
Ethernet ports for higher service availability.
To configure these ports, choose LAN from
the Network menu, and the LAN
Configuration screen appears. Press Apply
to save your changes.
LAN Configuration
Item Description
MAC Address Displays the MAC address of the LAN interface.
IP Specifies the IP address of the LAN interface.
Netmask Specifies the Network Mask of the LAN interface.
Jumbo Frame Support Enable or disable Jumbo Frame Support on the LAN interface.
DHCP Configuration
A DHCP server can be configured to assign IP addresses to devices connected to
the LAN port. To configure these ports, choose LAN from the Network menu.
DHCP Configuration
Item Description
DHCP Server Enable or disable the DHCP server to automatically assign IP
address to PCs connected to the LAN interface.
Start IP Specifies the starting IP address of the DHCP range.
End IP Specifies the ending IP address of the DHCP range.
DNS Server Displayed the DNS server IP address.
NOTE
Before enabling Jumbo Frame Support, please make sure your network
equipment supports Jumbo Frame. If your equipment is incompatible,
you might not be able to connect to your NDL-2400R. In this case, you
have to reset the system back to default by the holding down front
panel reset button for 5 seconds during boot up process.
NOTE
The IP Segment of WAN and LAN should not overlap.
WARNING
The IP address of the LAN interface should not be in th e range of the
Start IP address and End IP address.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 43
WLAN Configuration
When a compatible wireless USB dongle is
installed on the NDL-2400R, the NDL-2400R
will become an access point, and the
Network dropdown menu will contain a
WLAN menu item. From the Network menu,
choose WLAN, and the WLAN
Configuration screen appears. This screen
displays the wireless network parameters of
the system. You can change any of these
items and press Apply to confirm your
settings.
WLAN Configuration
Item Description
MAC Address Displays the MAC Address of the USB wireless dongle.
IP Specifies the IP address of the network connection.
Netmask
Specifies the network mask, which is generally: 255.255.255.0
ESSID The ESSID (Extended Service Set Identification) is the
identifying name of a wireless network.
ESSID Broadcast Specifies whether the ESSID will be broadcasted by the NDL-
2400R. This will prevent the Access Point from broadcasting the
ESSID. The NDL-2400R will still respond to a wireless device
that wants to communicate if it sends a matching ESSID.
Channel The channel that the NDL-2400R uses to communicate with
client devices.
Auth Mode Authentication mode used by the NDL-2400R.
Shared: Shared key authentication
Open: Open key authentication
WEP Enable Specifies whether to use encryption for transmission or not.
Key Length Key length specifies the level of encryption used by the NDL-
2400R.
64 bit: 10 characters from 0 ~ 9 and A ~ F.
128 bit: 26 characters from 0 ~ 9 and A ~ F.
WEP KEY 1 Input up to 4 WEP keys, and select the one you wish to use.
When connecting, be sure to enter the same key and select the
same index number on each client machine.
WEP KEY 2
WEP KEY 3
WEP KEY 4
A DHCP server can be configured to assign IP addresses to devices connected to
LAN ports.
WLAN DHCP Configuration
Item Description
DHCP Server Select to enable or disable DHCP server.
Start IP Specifies the starting IP address of the DHCP range.
End IP Specifies the ending IP address of the DHCP range.
DNS Server Specifies the DNS server IP address.
NOTE
• Currently supported USB
wireless dongles are: 3Com
3CRUSB10075, Zyxel G220USB,
PCI GW-US54mini.
• USB dongles have to be
connected before NDL-2400R is
powered up.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 44
Web Services Configuration
From the Network menu, choose the
Service item, and the Web Service screen
appears. This screen displays the service
support parameters of the system. You can
change any of these items and press Apply
to confirm your settings. A description of
each item follows:
Web Service
Item Description
HTTP (WebDisk)
Support
Enable or disable WebDisk support. Enter the port number if this
option is enabled. The port number
HTTPs (Secure
WebDisk) Support
Enable or disable secure WebDisk support. Enter the port if this
option is enabled.
SMB/CIFS Enable or Disable SMB/CIFS protocol for Windows, Apple, Unix
drive mapping.
UPnP Enable or disable Universal Plug and Play protocol. UPnP helps to
find the IP address of the NDL-2400R.
AFP (Apple Network Setup)
From the Network menu, choose the AFP
item, and the AFP Configuration screen
appears. This screen displays the
configuration items for the Apple Filing
Protocol. You can change any of these items
and press Apply to confirm your settings. A
description of each item follows:
NOTE
• Disable HTTP support and
Enable Secure HTTP support
to guarantee secure access.
• In some environments, due to
security concerns, you may
wish to disable SMB/CIFS as a
precaution against computer
viruses.
NOTE
The IP Segment of WLAN, WAN and LAN should not overlap.
NOTE
Users should obey the international RF regulatory rules as they set up
the wireless RF channel on the NDL-2400R. The RF operating
channels for different regions have been specified as following.
NASdeluxe has no responsibility for users attempting to violate the
international RF regulation.
11 N. America
14 Japan
13 Europe (ETSI)
2 Spain
4 France
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 45
Apple Network Configuration
Item Description
AFP Server Enable or disable Apple File Service to use the NDL-2400R with
MAC OS-based systems.
Zone Specifies Zone for Applet Talk service.
If your AppleTalk network uses extended networks and is
assigned with multiple zones, assign a zone name to the NDL2400R. If you do not want to assign a network zone, enter an
asterisk (*) to use the default setting.
NFS Setup
From the Network menu, choose the NFS
item, and the NFS Server Setting screen
appears. The NDL-2400R can act as an NFS
server, enabling users to download and
upload files with the favorite NFS clients.
Press Apply to confirm your settings. A
description of each item follows:
NFS Server Setting
Item Description
NFS Enable or Disable NFS support.
Apply Click Apply to save your changes.
Cancel Click Cancel to abandon your changes.
User and Group Management
The NDL-2400R has built-in user database that allows administrators to manage
user access using different group policies. From the Accounts menu, you can
create, modify, and delete users, and assign them to groups that you designate.
Local User Configuration
From the Accounts menu, choose the
Users item, and the Local User
Configuration screen appears. This screen
allows you to Add, Modify, and Delete
local users.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 46
Local User Configuration
Item Description
Add Press the Add button to add a user to the list of local users.
Modify Press the Modify button to modify a local user.
Delete Press the Delete button to delete a selected user from the
system.
Adding Users
1. Click on the Add button on Local
User Configuration screen, and
Local User Setting screen appears.
2. On the Local User Setting screen,
enter a name in the User Name box.
3. Enter a User ID number. If left
blank, the system will automatically
assign one.
4. Enter a password in the Password
box and re-enter the password in the
Confirm box.
5. Select which group the user will belong to. Group Members is a list of
groups this user belongs to. Group List is a list of groups this user does
not belong to. Use the << or >> buttons to have this user join or leave a
group.
6. Press the Apply button and the user is created.
NOTE
All users are automatically assigned to the ‘users’ group.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 47
Modifying Users
1. Select an existing user from the Local User Configuration screen.
2. Click on the Modify button, and Local User Setting screen appears.
3. From here, you can enter a new password and re-enter to confirm, or use
the << or >> buttons to have this user join or leave a group. Click the
Apply button to save your changes.
Deleting Users
1. Select an existing user from the Local User Configuration screen.
2. Click on Delete button and the user is deleted from the system.
Local Groups Configuration
From the Accounts menu, choose the
Groups item, and the Local Groups
Configuration screen appears. This screen
allows you to Add, Modify, and Delete
local groups.
Local Groups Configuration
Item Description
Add Press the Add button to add a user to the list of local groups.
Modify Press the Modify button to delete a selected group from the
system.
Delete Press the Delete button to delete a selected group from the
system.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 48
Adding Groups
1. On the Local Group Configuration screen, click on the Add button.
2. The Local Group Setting screen appears.
3. Enter a Group Name.
4. Enter a Group ID number. If left blank, the system will automatically
assign one.
5. Select users to be in this group from
the Users List by adding them to
the Members List using the <<
button.
6. Click the Apply button to save your
changes.
Modifying Groups
1. On the Local Group Configuration
screen, select a group name from
the list.
2. Press the Modify button to modify
the members in a group.
3. To add a user into a group, select the user from the Users List, and press
the << button to move the user into the Members List.
4. To remove a user from a group, select the user from Members List, and
press the >> button.
5. Click the Apply button to save your changes.
Deleting Groups
1. On the Local Group Configuration screen, select a group name from the
list.
2. Press Delete to delete the group from the system.
Batch User and Group Creation
The NDL-2400R can also add users and
groups in batch mode. This enables you to
conveniently add numerous users and
groups automatically by importing a simple
comma-separated plain text (*.txt) file.
From the Accounts menu, click Batch
Mgmt and the Batch Create Users and
Groups dialogue will appear. To import
your list of users and groups, follow these
steps:
1. Click Browse… to locate your
comma-separated text file.
The information in the text file should follow this format:
[USERNAME], [PASSWORD], [GROUP]
2. Click Open.
3. Click Import to begin the user list import.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 49
ADS/NT Configuration
If you have a Windows Active Directory
Server (ADS) or Windows NT server to
handle the domain security in your network,
you can simply enable the ADS/NT support
feature; the NDL-2400R will connect with
the ADS/NT server and get all the
information of the domain users and groups
automatically. From the Accounts menu,
choose Authentication item and the
ADS/NT Support screen appears. You can
to change any of these items and press
Apply to confirm your settings. A
description of each item follows:
ADS/NT Support
Item Description
WINS Server Specifies the WINS server if necessary.
Work Group / Domain
Name
Specifies the SMB/CIFS Work Group / ADS Domain Name (e.g.
NDL-2400R).
ADS/NT Support Select Disable to disable authentication through Windows Active
Directory Server or Windows NT.
Authentication Method Select ADS for Windows Active Directory Server, or select NT for
Windows NT
ADS/NT Server Name Specifies the ADS/NT server name (e.g. adservername).
ADS/NT Realm Specifies the ADS/NT realm (e.g. example.com).
Administrator ID Enter the administrators ID of Windows Active Directory or
Windows NT, which is required for NDL-2400R to join domain.
Administrator
Password
Enter the ADS/NT Administrator password.
Confirm Password For re-entering password to confirm.
To join an AD domain, you can refer the figure and use the example below to
configure the NDL-2400R for
associated filed input:
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 50
AD Domain Example
Item Information
Work Group / Domain
Name
domain
ADS Support
Enable
ADS Server Name
Computer1
ADS/NT Realm
Domain.local
Administrator ID
Administrator
Administrator
Password
***********
Confirm Password
***********
NOTE
• The DNS server specified in the WAN configuration page should be
able to correctly resolve the ADS server name.
• The time zone setting between NDL-2400R and ADS should be
identical.
• The system time difference between NDL-2400R and ADS should be
less than five minutes.
• The Administrator Password field is for the password of ADS (Active
Directory Server) not NDL-2400R.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 51
System Settings
The System menu gives you a wealth of settings that you can use to configure
your NDL-2400R’s system administration functions. You can set up system
notifications, view system logs, and even upgrade firmware from this menu.
System Notifications
From the System menu, choose the
Notification item, and the Notification
Configuration screen appears. This screen
lets you have the NDL-2400R notify you in
case of any system malfunction. Press
Apply to confirm all settings. See following
table for a detailed description of each item.
Notification Configuration
Item Description
Beep Notification Enable or disable the system beeper that beeps when a problem
occurs.
Email Notification Enable or disable email notifications of system problems.
SMTP Server Specifies the hostname/IP address of the SMTP server.
Port Specifies the port to send outgoing notification emails.
Auth Type Select the SMTP Server account authentication type.
SMTP Account ID Set the SMTP Server Email account ID.
Account Password Enter a new password.
Confirm Account
Password
Confirm a new password.
Receiver’s E-mail
Address
Add one or more recipient’s email addresses to receive email
notifications.
Test E-Mail Click to send out a test e-mail to make sure the settings are
correct.
System Logs
From the System menu, choose the Logs
item and the System Logs screen appears.
This screen shows a history of system usage
and important events such as disk status,
network information, and system booting.
See the following table for a detailed
description of each item:
NOTE
Consult with your mail server
administrator for email server
information.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 52
System Logs
Item Description
Truncate All Log File Clear all log files.
|<< < > >>| Use the forward ( > >>| ) and backward ( |<< < ) buttons
to browse the log pages.
INFO Provides all log information including warning messages and
error messages.
WARN Shows all warning messages and error messages.
ERROR Shows only error messages.
GO Specify the number of lines per page and press Go.
Ascending Shows logs by date in ascending order.
Descending Shows logs by date in descending order.
Download All Log File Export all logs to an external file.
Time and Date Settings
From the System menu, choose the Time
item and the Time screen appears. Set the
desired Date, Time, and Time Zone. You
can also elect to synchronize the system
time on the NDL-2400R with an NTP
(Network Time Protocol) Server. You
can change any of these items and press
Apply to confirm your settings.
See the following table for a detailed
description of each item:
Time
Item Description
Date Sets the system date.
Time Sets the system time.
Time Zone Sets the system time zone.
NTP Server Select Yes to allow the NDL-2400R to synchronize with the NTP
server shown below.
Select Manually to allow the NDL-2400R to synchronize with an
NTP server of your choice.
Select No to not have the NDL-2400R to synchronize with an
NTP server.
WARNING
If an NTP server is selected, please make sure your NDL-2400R’s
network has been setup to access the NTP server.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 53
System Configuration Backup and Restore
From the System menu, choose the Config
Mgmt item and the System Configuration
Download/Upload screen appears. From
here, you can download or upload stored
system configurations. See the following
table for a detailed description of each item.
System Configuration Download/Upload
Item Description
Download Save and export the current system configuration.
Upload Import a saved configuration file to overwrite current system
configuration.
Reset to Factory Default Settings
From the System menu, choose the
Factory Default item and the Reset to
Factory Default screen appears. Press
Apply to reset the NDL-2400R to factory
default settings. Press Cancel to go back to
the main menu.
NOTE
Backing up your system configuration is a great way to ensure that you
can revert to a working configuration when you are experimenting with
new system settings.
The system configuration you have backup can be only restore in same
firmware version. And the backup details have excluded user/group
accounts.
WARNING
Resetting to factory defaults will not erase the data stored in the hard
disks, but WILL revert all the settings to the factory default values.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 54
Upgrading System Firmware
From the System menu, choose the
Firmware Upgrade item and the
Firmware Upgrade screen appears.
Follow the steps below to upgrade your
firmware:
1. Use the Browse button to find the
firmware file.
2. Press Apply.
3. The beeper beeps and the Busy LED
blinks until the upgrade is complete.
Change Administrator Password
From the System menu, choose the
Administrator Password item and the
Change Administrator Password screen
appears. Enter a new password in the New
Password box and confirm your new
password in the Confirm Password box.
Press Apply to confirm password changes.
See the following table for a detailed
description of each item.
Change Administrator Password
Item Description
New Password Type in a new administrator password.
Confirm Password Type the new password again to confirm.
Apply Press this to save your changes.
NOTE
• The beeper only beeps if it is enabled in the System Notification
menu.
• Check NASdeluxe website for the latest firmware release and release
notes.
WARNING
Do NOT turn off the system during the firmware upgrade process. This
will lead to a catastrophic result that may render the system inoperable.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 55
Reboot and Shutdown System
From the System menu, choose Reboot &
Shutdown item, and the
Shutdown/Reboot System screen
appears. Press Reboot to restart the system
or Shutdown to turn the system off.
Logout
To logout of the Web Administration Interface, navigate to System > Logout.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 56
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 57
Chapter 5: Additional Feature Setup
Overview
The NDL-2400R can also act as an FTP Server, allowing employees and clients to
transfer files using their favorite FTP programs. The integrated Print Server allows
you to share a single USB printer will all users on the network. The following
section shows you how.
FTP Server
NDL-2400R can act as a FTP server, enabling
users to download and upload files with their
favorite FTP programs. From the Network
menu, choose the FTP item, and the FTP
screen appears. You can change any of these
items and press Apply to confirm your
settings. A description of each item follows:
FTP
Item Description
FTP Enable FTP Service on the NDL-2400R.
FTP ENCODE If your FTP client or operating system does not support Unicode
(e.g. Windows® 95/98/ME or MAC OS9/8), select the same
encoding as your OS here in order to properly view the files and
directories on the server. Available options are BIG5, HZ,
GB2312, GB18030, ISO, EUC-JP, SHIFT-JIS and UTF-8.
To access the share folder on the NDL-2400R, use the appropriate user login and
password set up on the Users page (Accounts > Users). Access control to each
share folder is set up on the ACL page (Storage > Folder > ACL).
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 58
Printer Server
You can configure the NDL-2400R to act as
a printer server. That way, all PCs
connected to the network can utilize the
same printer.
Windows XP SP2
To set up the Printer Server in Windows XP
SP2, follow the steps below:
1. Connect the USB printer to one of
the USB ports (preferably the rear
USB ports; front USB ports can be
used for external HDD enclosures).
2. Go to Start > Printers and Faxes.
3. Click on File > Add Printer.
4. The Add Printer Wizard appears on your screen. Click Next.
5. Select the “A network printer, or a printer attached to another
computer” option.
6. Select “Connect to a printer on the Internet or on a home or office
network”, and enter “http://NDL2400R_IP_ADDRESS:631/printers/usb-printer” into the URL field.
7. Your Windows system will ask you to install drivers for your printer. Select
correct driver for your printer.
8. Your Windows system will ask you if you want to set this printer as
“Default Printer”. Select Yes and all your print jobs will be submitted to
this printer by default. Click Next.
9. Click Finish.
NOTE
• Not all USB printers are supported. Please check NASdeluxe website
for a list of supported printers.
• Note that if a multi-function (all-in-one) printer is attached to the
NDL-2400R, usually only the printing and fax functions will work.
Other features, such as scanning, will probably not function.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 59
Windows Vista
To set up the Printer Server in Windows Vista, follow the steps below:
1. Open Printer Folder from the Control Panel.
2. Click the right mouse button in anywhere on the Printers folder and then
select Add Printer.
3. Select Add a network, wireless or Bluetooth printer.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 60
4. Select The printer that I want isn’t listed.
You can press The printer that I want isn’t listed to go into next page
without waiting for Searching for available printers to finish.
5. Click Select a shared printer by name.
Type http://<NASdeluxe_NAS>:631/printers/usb-printer in the box,
where <NASdeluxe_NAS_IP> is the IP address of the NDL-2400R. Click
Next.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 61
6. Select or install a printer and then press OK.
If your printer model is not listed, please contact your printer
manufacturer for help.
7. Windows will attempt to connect to the printer.
8. You can choose to set this printer as the default printer by checking the
Set as the default printer box. Click Next to continue.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 62
9. Done! Click Finish.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 63
Chapter 6: Using the NDL-2400R
Overview
Once the NDL-2400R is setup and operating, users on the network may manage
all varieties of digital music, photos, or files by simply using their web browsers.
To manage your personal files or access public files on the NDL-2400R, just enter
its IP address into your browser (default IP address is http://192.168.1.100),
and you will be taken to the NDL-2400R Login page.
Login Page
To login to the system, enter your user name and password, and click Login to
log into the system. You will be taken to the WebDisk interface.
Using WebDisk
The NDL-2400R provides a WebDisk function that allows you to access the
system over the Internet from any browser.
1. In the Login page, type in the User ID and password that were previously
set for you in the Accounts menu. See Chapter 4: System Management
> User and Group Management > Local User Configuration.
2. The WebDisk page appears showing folders made currently available to
you via the Access Control List (ACL).
3. Click on a folder name to enter the folder.
4. The folder’s page appears displaying files and folders. Click on a file to
download the file.
Folder Page
Item Description
Name Displays the names of folders and files.
Size Shows the size of folders and files.
Type Displays the type of folders and files.
Modified Date Shows the time of most recent modification of folders and files.
5. Buttons on the folder page allow you to create a new folder, upload files
and delete files in the folder.
Folder Page Buttons
Button Description
Up Goes to the previous folder level.
New folder Creates a new folder.
New file (upload) Uploads a file from your computer to the current folder.
Delete Selected Items Deletes selected files and folders.
6. To create a new folder within the current folder, press the New folder
button. When the screen appears enter a name for the folder. Press OK to
create the folder.
NOTE
Before proceeding, make sure that WebDisk Support or Secure
WebDisk Support is enabled in the Service Support screen in the
system’s Network menu. See Service Support in Chapter 4: System
Management > Network Management > Web Services Configuration.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 64
7. To upload a file from your computer to the current folder, press the New
file (upload) button. When the screen appears, press Browse and locate
the file to upload. Press OK and the file is uploaded to the current folder.
8. To delete a file or folder, select the file or folder’s check box. Press the
Delete selected items button. You can also check the check box as the red
circle indicates to select all files and folders in this folder.
To access folders with access control, you must first login with a local user
account.
For more information on how to setup user rights to the folders, please check
Chapter 4: System Management > Folder Management > Folder Access
Control List (ACL).
Mapping a Client PC to the NDL-2400R
You can map share folders on the NDL-2400R so that you can access them as if
they were drives on your computer. You can connect to the shared network
folders on the NDL-2400R as follows:
Windows
1. Go to the My Computer folder in Windows.
2. In the menu bar, select Tools and then Map Network Drive…
3. The Map Network Drive window appears.
4. Assign a drive letter for the share folder.
5. Click the Browse button to find the folder over your network. Alternatively,
you may enter the folder name you wish to connect to or enter its IP
address. (i.e. \\192.168.1.100\share)
6. Click Finish. When the Connect As… window appears, enter your user
name and password.
7. Click OK. The share folder appears as the drive you assigned. You can now
access this folder as though it were a drive on your computer.
Apple OS X
On an Apple computer, you can connect to shared computers and servers using a
network address.
1. Choose Go > Connect to Server…
2. Enter the network address for the server in the Server Address text box.
When connecting using SMB/CIFS protocol, type:
smb://192.168.1.100/Folder1
When connecting using AFP protocol, type:
afp://192.168.1.100/Folder1
Click Connect.
3. When MAC OS X is trying to connect NDL-2400R, it will ask for a User
Name and Password which has access to the folder.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 65
4. When MAC OS X has connected to the NDL-2400R successfully, an icon
representing the folder will appear on the MAC OS X desktop. You can
access the folder by double clicking on the icon.
Mapping the NDL-2400R as an iSCSI Drive
With the NDL-2400R, you are able to map it as an iSCSI drive. With iSCSI, you
can remotely access the NDL-2400R at great speeds, as if it were installed as a
local drive in your computer.
To do this, simply follow the steps below:
Windows 2000/XP
1. First, download the iSCSI Initiator from the Microsoft website
(http://www.microsoft.com). You can find this software by entering iSCSI
Initiator into the search box on their homepage.
2. Once the download is complete, install the iSCSI Initiator by doubleclicking the EXE file. You may be presented with the following security
warning. Click Run to continue.
3. You will now install the iSCSI Initiat o r using the Setup Wizard. Click Next
to continue.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 66
4. Leave the default selections and click Next.
5. Read the license agreement. To continue with the installation, click I
Agree and then click Next.
6. The iSCSI Initiator will now install automatically. Click Finish once
completed.
7. Start the iSCSI Initiator by double-clicking its icon on the desktop. The
iSCSI Initiator properties window will appear.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 67
8. Select the Discovery tab. Under Target Portals, click Add.
9. Enter the IP address of the NDL-2400R. Click OK.
10. On the iSCSI Initiator Properties window, select the Targets tab. With
the iSCSI target highlighted, click Log On. The Log On to Target
dialogue will appear.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 68
11. If you have not enabled CHAP, click OK to continue.
If you have enabled CHAP, click Advanced. Under Advanced Settings,
check the CHAP login information checkbox and enter your username
and password. Click OK.
12. Right click My Computer on the desktop and select Manage.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 69
13. Click on Disk Management and you will see a new hard disk listed.
14. Initialize the new hard disk and you will then be able to use the iSCSI
target as a local drive.
Windows Vista
Because Windows Vista has the Microsoft iSCSI Initiator pre-installed, you will not
have to install this piece of software. Instead, start the iSCSI Initiator and follow
steps 8-14 to map the NDL-2400R as an iSCSI drive.
File Backup
There are a number of ways to back up data with the NDL-2400R.
Nsync
You can backup a share folder to another NDL-2400R (Nsync Target) or any FTP
server for safe keeping as long as you have appropriate access right on that
target. When using Nsync between two NDL-2400R-S, you have the option to
transmit files securely between two NDL-2400R-S.
If the files on your NDL-2400R are lost for any reason, you can restore those files
from the target NDL-2400R. To backup files regularly, you can set up a scheduled
task to run only once, daily, weekly, or monthly. You can also limit the bandwidth
of your Nsync tasks, so other users on the network can share the bandwidth
equally.
Under the Storage menu, click Nsync and the Nsync window appears. Below is
a description of each field:
Nsync
Item Description
Task name The name of your Nsync task.
Server The IP address of your target server
Share folder The share folder you would want to backup.
Last Time The time when the last Nsync task was executed.
Last Status The status of your last Nsync task.
Action Administrator can run or stop an Nsync task by pressing the
action button.
Bandwidth Setting Bandwidth control on Nsync tasks.
Add Click to add a Nsync task
Modify Click to modify an Nsync task.
Restore Restore share folder from an Nsync target.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 70
Delete Click to delete an Nsync task. Backup files on Nsync target is
also deleted.
Adding an Nsync Task
From the Nsync Information screen, click Add to display the Add Nsync Task
screen.
Add Nsync Task
Item Description
Task Name The name of your Nsync task.
Manufacturer Select whether the target is a NASdeluxe Product (e.g. NDL-
2400R) or FTP server.
Target Server IP
Address
The IP address of your target server.
Source Folder The share folder you want to backup.
Nsync Task Name The name of your Nsync task.
Authorized Username
on Target Server
The account name on the target server.
Password on Target
Server
The password for the username on the target server.
Test Connection Click to check the connection to the Target Server.
Schedule Schedule backup of your share folders.
Time The time when the Nsync task will run.
Type Select whether to run the Nsync task daily, weekly, or monthly.
Daily: input the time of day to execute Nsync task.
Weekly: input which day of the week to execute the task.
Monthly: decide which day of the month to execute the task.
Apply Click to submit the task.
Setting Up an Nsync Target on an Nsync Device
On the Nsync target server, the administrator of that server has to set up a user
account with a folder named “nsync” and grant write access.
1. On the Nsync server, add a user for Nsync source (ex. nsyncsource1). For
instructions on how to add a user on the NDL-2400R, see Chapter 4:
System Management > User and Groups Management > Local User
Configuration > Adding Users.
2. On the Nsync server, grant that user (ex. nsyncsource1) write access to
the nsync folder. For instructions on how to set up a folder’s ACL, see
Chapter 4: System Management > Folder Management > Folder
Access Control List (ACL).
3. Once this is done, the target server will start accepting Nsync tasks from
server using that ID and password.
Setting Up an Nsync Target on Another Device
If you selected “Other Device” when setting up your Nsync task, the NDL-2400R
will use the FTP protocol to back up the share folder. On the external storage
device, make sure there is a folder named “nsync”, and the Auth ID has writable
permission in that folder.
NOTE
Before starting an Nsync Task, make sure the target server’s Nsync
Server (or FTP Server) is enabled.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 71
Designating NDL-2400R as an Nsync Target
The NDL-2400R can act as an Nsync server, enabling another Nsync-equipped
NASdeluxe NAS at a remote location backup their files to this NDL-2400R. From
the Network menu, choose the Nsync Target item, and the Nsync Target
Server Setting screen appears.
Nsync Target Server Setting
Item Description
Nsync Target Server Enable or Disable Nsync Target support.
NASdeluxe Backup Utility
The NASdeluxe Backup Utility is on your Installation CD. When you click on the
CD, the Backup Utility will be installed under Program Groups > NASdeluxe >
NASdeluxe Backup Utility. If it is not installed, you can copy the file
(NASdeluxe Backup Utility.exe) to a convenient location on your hard disk and
double click to execute it.
When you execute this utility for the first time, it will ask you whether to create a
DB file. Click Yes.
1. Click Add to create a Backup task. The Add New Task dialog box appears.
Add New Task
Item Description
Task Specifies a name for the current task.
Source Click to specify the source folder/file location.
Incremental Click to specify whether the backup will be incremental.
If unchecked, the backup will be a full backup.
Destination Click to specify the destination folder/file location.
Excluded extensions Files with these file name extensions will be skipped and not
back up to the destination.
Comments If you wish, enter comments here for your records.
2. To schedule the task to run at regular intervals, click on the Schedule
icon for that task. You can schedule the task to run Monthly or Weekly.
3. To check the log for that task, click on the Log icon for that task.
NOTE
If you can not find NASdeluxe Backup Utility on your CD, please
download it from the NASdeluxe website (http://www.NASdeluxe.com).
NOTE
NASdeluxe Backup Utility also supports MAC OS X. Just copy the
NASdeluxe Backup Utility.dmg to your MAC OS X machine and double
click to execute it.
NOTE
To enable Nsync task to go thru firewall, you have to open port
TCP/1194 on your firewall in both directions.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 72
Windows XP Data Backup
If you use Windows XP Professional, you can also use the Wind ows Backup Utility
(Ntbackup.exe) to backup your files.
If you use Windows XP Home Edition, follow these steps to install the utility:
1. Insert the Windows XP CD into a drive and double-click the CD icon in My
Computer.
2. When the Welcome to Microsoft Windows XP screen appears, click
Perform Additional Tasks.
3. Click Browse this CD.
4. In Windows Explorer, navigate to ValueAdd > Msft > Ntbackup.
5. Double-click Ntbackup.msi to install the backup ut ility.
Once installed, you can use the Windows Backup Utility by followin g the steps
below:
1. Click Start, and point to All Programs > Accessories > System Tools
> Backup to start the wizard.
2. Click Next to skip past the opening page. Choose Backup files and
settings from the second page, and then click Next.
3. Select which option you want to back up.
4. Click Next and in the Backup Type, Destination, and Name page, specify a
back up location using the Browse button.
5. Find and select the drive that specifies your NDL-2400R as your backup
destination and click Next.
6. Click Next to display the wizard’s final page and click Finish to start
backing up.
Apple OS X Backup Utilities
Mac OS X does not include any backup software. However, there are a number of
backup solutions available for the Mac OS X, including: iBackup, Psyncx, iMSafe,
Rsyncx, Folder Synchronizer X, Tri-BACKUP, Impression, Intego Personal Backup,
SilverKeeper, and Apple's dotMac Backup utility to name just a few. To find even
more freeware and shareware backup utilities to choose from, go to
VersionTracker or MacUpdate and search on "backup".
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 73
Chapter 7: Tip s and Tricks
USB and eSATA Storage Expansion
The NDL-2400R supports external USB hard disks through its three USB ports.
Once a USB hard disk has successfully mounted, the entire volume will be copied
automatically to the default USB HDD folder. The NDL-2400R supports up to 6
USB external storage devices. All file names on the USB disk volume are case
sensitive.
The NDL-2400R also supports eSATA hard disks with its eSATA port.
Before attaching an eSATA or USB disk drive to NDL-2400R, you have to partition
and format it on a desktop computer or a notebook first. The attached device will
be located at \\192.168.1.100\usbhdd\sdf1 where 192.168.1.100 means the
IP address of NDL-2400R and sdf1 stands for the first partition on disk #6, the
eSATA or USB disk drive. If it is an NTFS partition, NAS users can open or copy
files from \\192.168.1.100\usbhdd\sdf1 but cannot add new files or modify
existing files.
Adding a Spare Disk
With a RAID 1, RAID 5, RAID 6, or RAID 10 volume, you can add a spare disk
after the initial RAID is setup. To add a spare disk, follow the steps below:
1. On the RAID Configuration Screen, tick the checkbox of the hard disk
you wish to designate as a spare disk.
2. Click Add Spare. The disk will be configured as a spare disk. The system
automatically rebuilds the spare disk when one of the disks in the RAID set
fails.
Target USB
NDL-2400R can operate in dual mode. When connecting to a regular USB disk or
thumb drive, NDL-2400R is acting as USB host. When connecting to a PC thru its
USB Type B connector on the back panel, NDL-2400R can act as a USB disk. This
feature allows user to transfer files without using network connection.
When you create RAID, you can assign a portion of space on the RAID to be used
as USB disk. When connecting NDL-2400R to a PC using the supplied USB A to B
cable, the PC will recognize this space as an unformatted disk. At this point, the
PC can format this portion of disk and create file system on it. Since this disk is
created on the RAID, it will be protected by the RAID level you select.
NOTE
If you want to write to an USB storage device, the file system must be
FAT32.
USB Storage
FAT32 Partition NTFS Partition
Read OK OK
Write OK -
WARNING
When RAID is removed or damaged, all the data on the Target USB
device will be deleted.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 74
Remote Administration
You can set up your NDL-2400R for remote administration. With remote
administration, you can access your NDL-2400R over the Internet, even if your
NDL-2400R is behind a router. This is especially useful if you are traveling and
suddenly need a file from your NDL-2400R.
Setting up remote administration is a three-part process, and will require the
following equipment:
• NASdeluxe NDL-2400R NAS device
• Cable/DSL Router with Dynamic DNS support
• Home PC
• Internet Connectio n
Part I - Setup a DynDNS Account
1. Go to http://www.dyndns.org from your home PC.
2. Click on the Sign Up Now link.
3. Check the Check boxes, select a user name (i.e.: NDL-2400R), enter your
email address (i.e.: xxx@example.com), check Enable Wildcard, and
create a password (i.e.: xxxx).
4. Wait for an email from www.dyndns.org.
5. Open the email and click on the link to activate your account
Part II - Enable DDNS on the Router
1. Go to the router setup screen and select IP Config > Miscellaneous
DDNS Setting from your Home PC.
2. Click on Yes for Enable the DDNS Client?
3. Select www.dyndns.org.
4. Go to router setup screen, and enter the following information:
a. User Name or E-mail Address: xxx@example.com
b. Password or DDNS Key: xxxx
c. Host Name: www.NDL-2400R.dyndns.org
d. Enable wildcard? Select Yes
e. Update Manually: Click Update
Part III - Setting up Virtual Servers (HTTPS)
1. Navigate to NAT Setting > Virtual Server.
2. For Enable Virtual Server?, select Yes
3. Setup the HTTPS Server
a. Well-Known Applications: Select User Defined
b. Local IP: Enter 192.168.1.100
c. Port Range: 443 (the default HTTPS port setting on the NDL-
2400R)
d. Protocol: select TCP
e. Click Add.
f. Click Apply.
4. Test the HTTPS connection from another computer on the Internet
a. From a remote computer, open your browser and enter
NOTE
Router setup will differ slightly depending on router used. For this
example, we will use the Asus WL500g because it has support for
Dynamic DNS. Contact your router hardware vendor for setup help.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 75
https://www.NDL-2400R.dyndns.org
b. You should see the login page of NDL-2400R.
Firewall Software Configuration
If you are using a software firewall (i.e. Norton Internet Security) and are having
trouble connecting to the NDL-2400R, you can try the following steps:
1. Double click the NIS icon on system tray, and then configure the
Personal Firewall.
2. On the Programs page, find the SetupWizard.exe and change its
permission to "Permit All". If it's not in the program list, use the Add or
Program Scan buttons to find it.
3. On the Networking page, manually add NDL-2400R IP address (i.e.
192.168.1.100) to the Trusted list.
Replacing Damaged Hard Drives
If you are using RAID 1, RAID 5, RAID 6, or RAID 10, you can easily replace a
damaged hard drive in the NASdeluxe NDL-2400R while keeping your data secure
with the system’s automatic data recovery.
Hard Drive Damage
When a hard drive is damaged and data in the RAID volume, the system LCD will
display warning message also the system beeps.
Replacing a Hard Drive
To replace a hard disk drive in the NDL-2400R:
1. Remove the tray with the damaged hard disk.
2. Unscrew the damaged hard disk and remove it from the tray.
3. Slide a new hard disk into the tray and fasten the screws.
4. Insert the hard disk tray back into the NDL-2400R until it snaps into place.
You can also lock it with a key if desired.
5. The LED blinks green when the HDD is accessed.
RAID Auto-Rebuild
When using RAID 1, 5, 6, or 10 on the NDL-2400R, you can use the auto-rebuild
function when an error is detected.
1. When a hard disk fails the system beeps and/or an email notification is
sent to specified receivers.
2. Check the LCD to see which disk has failed.
3. Follow the steps mentioned above to replace the failed hard disk.
4. The system automatically recognizes the new hard disk and starts the
auto-rebuild sequence to resume its status before the hard disk crash.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 76
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 77
Chapter 8: Troubleshooting
Forgot My Password
If you forget your password, you can reset the unit to use the defaul t password.
To do this, press the reset button on the front panel after system is booted, and
NDL-2400R will be reset. WAN IP address will become 192.168.1.100 and admin
password will be admin.
Forgot My Network IP Address
If you forget your network IP address and have no physical access to the system,
you can find out the IP address by either looking directly onto the NDL-2400R’s
LCD panel, or by using the setup wizard to retrieve the IP of your NDL-2400R.
1. Start the Setup Wizard, and it will automatically detect all NASdeluxe IP
storage products on your network.
2. You should be able to find the IP address of the NDL-2400R which you
have forgotten in the Device Discovery screen.
Resetting NAS IP Address and Admin Password
In case you changed the NDL-2400R IP address and then forgot it, or forgot the
administration password, follow the steps below to reset to default settings:
1. Power on the NDL-2400R till system ready and press the Reset button
while buzzer with long beeping approximately 3-5 seconds. (The reset
button is right below power button)
2. This resets the NDL-2400R to its default IP address and password settings.
Default IP: 192.168.1.100 for WAN and 192.168.2.100 for LAN
Default admin password: admin
Jumbo Frame support: disabled
HTTP Port: 80, HTTPs:443
Can't Map a Network Drive in Windows XP
You may have problems mapping a network drive under the following conditions:
1. The network folder is currently mapped using a different user name and
password. To connect using a different user name and password, first
disconnect any existing mappings to this network share.
2. The mapped network drive could not be created because the following
error has occurred: Multiple connections to a server or shared
resource by the same user, using more than one user name, are
not allowed. Disconnect all previous connections to the server or shared
resource and try again.
To check out existing network connections, type net use under the DOS prompt.
You may refer the URL below for more network mapping information.
http://www.NASdeluxe.com
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 78
Restoring Factory Defaults
From the System menu, choose the Factory Default item and the Reset to
Factory Default screen appears. Press Apply to reset the NDL-2400R to factory
default settings.
Problems with Time and Date Settings
The administrator is able to select an NTP Server to keep the NDL-2400R’s time
synchronized. However, if the NDL-2400R can not access the Internet, you may
encounter a problem when setting the Time and Time Zone. If this happens:
1. Login to the Web Administration Interface.
2. Navigate to System > Time.
3. Under NTP Server, select No.
4. Set the Date, Time, and Time Zone.
5. Click Apply.
In addition, if the NDL-2400R is able to access the Internet and you want to keep
the NTP Server clock.isc.org by default, please make sure the DNS Server is
correctly entered, thereby allowing the NTP Server name to correctly resolve.
(See Network > WAN > DNS Server)
WARNING
Resetting to factory defaults will not erase the data stored in the hard
disks, but WILL revert all the settings to the factory default values.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 79
Appendix A: Product Specifications
Hardware Specifications
Product Model NDL-2400R-R NDL-2400R-S
Core Processors / Memory
Processor Intel® Celeron™ M 1.5GHz
Memory 512MB standard
Network Interfaces
LAN 1 Gigabit RJ-45 connector
LAN 2 Gigabit RJ-45 connector
Storage
HDD Bays 4 x 3.5” SATA II HDD, hot-swappable
HDD Support SATA II HDDs up to 1000GB
eSATA 1 x eSATA connector for capacity expansion
I/O Interfaces
USB Ports 3 x USB type A ports (Host mode)
1 x USB type B ports (Client mode)
System Information
LCD Control Panel For basic configurations and status display
System LED Display 4 x LED (System Busy, Power, Network Activity x 2)
Physical
Form Factor 1U rackmount
Height 44.0 mm
Width 430.5 mm
Depth 567.6 mm
Power Supply 250W redundant power
supply
100~240V AC, 50/60Hz
200W power supply
100~240V AC, 50/60Hz
Environment
Temperature 0 ~ 40°C
Humidity 20 ~ 85% relative humidity (non-condensing)
Certifications CE, FCC, BSMI, C-Tick, RoHS Compliant
Software Specifications
Network File Protocols Microsoft Networks (CIFS/SMB)
Apple Filing Protocol (AFP 3.1)
Network File System (NFS v3)
File Transfer Protocol (FTP)
Hyper Text Transfer Protocol (HTTP)
Secure Hyper Text Transfer Protocol (HTTPs)
Authentication Local User Account
Microsoft NT Domain Controller (PDC)*
Microsoft Active Directory Authentication (AD)*
Network Client Type Microsoft Windows NT/2000/XP/2003/Vista
Unix/Linux/BSD
MAC OS X/9/8.6
Network Configuration Fixed IP address
Dynamic IP address
802.3ad based failover and link aggregation
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 80
Disk Management Disk status monitoring (S.M.A.R.T.)
Disk idle spin-down
RAID RAID 0, 1, 5, 6, 10, and JBOD
Supports multiple RAID modes – users can create
multiple RAID volumes with different RAID levels in
one system
Auto rebuild
Hot swappable
Hot spare
Disk roaming
RAID level migration
RAID expansion
iSCSI Target Supports:
Microsoft iSCSI Initiator v2.0.4
StarPort Initiator V3.5.2
MAC OS: globalSAN iSCSI initiator version 3.0
(1150)
Linux: open-iscsi 2.0-865
Folder Management Share folder level permission
File level permission
Public folder
Quota Management Share folder quota control
Backup NASdeluxe Backup Utility (Windows XP/2000 and
MAC OS X)
NASdeluxe Nsync
System Management Web GUI
Multilingual support (English, French, German,
Italian, Traditional Chinese, Simplified Chinese,
Japanese, Korean, and Spanish)
NTP support
Wake-on-LAN
Scheduled Power On/Off
Event Notification Email notification
Buzzer notification
LCD
UPS Support UPS monitoring via RS-232 and system shutdown
on low battery
Printer Server USB Printer (IPP support)
Supported USB Devices USB Printer
External HDD/flash disk
USB IEEE 802.11 b/g dongle w/AP mode support**
Setup Utility Windows 2000/XP/2003
MAC OS X
*PDC/AD support: Works as a client member in a Microsoft NT 4.0 domain/Active
Directory domain, allowing the NDL-2400R to utilize the domain users and groups
setting for authentication to the system and authorization to the share folders.
**For supported USB dongles, please contact http://www.NASdeluxe.com
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 81
Appendix B: Customer Support
If your NDL-2400R is not working properly, we encourage you to check out
Chapter 8: Troubleshooting, located in this manual. You can also try to ensure
that you are using the latest firmware version for your NDL-2400R. NASdeluxe is
committed to providing free firmware upgrades to our customers. Our newest
firmware is available on our Download Center:
http://www.NASdeluxe.com
If you are still experiencing problems with your NDL-2500T, or requ ire a Return
Merchandise Authorization (RMA), feel free to contact technical support via our
Website.
Thank you for choosing
NASdeluxe!
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 82
Appendix C: RAID Basics
Overview
A Redundant Array of Independent Disks (RAID) is an array of several hard disks
that provide data security and high performance. A RAID system accesses several
hard disks simultaneously, which improves I/O performance over a single hard
disk. Data security is enhanced by a RAID, since data loss due to a hard disk
failure is minimized by regenerating redundant data from the other RAID hard
disks.
Benefits
RAID improves I/O performance, and increases data security through fault
tolerance and redundant data storage.
Improved Performance
RAID provides access to several hard disk drives simultaneously, which greatly
increases I/O performance.
Data Security
Hard disk drive failure unfortunately is a common occurrence. A RAID helps
prevent against the loss of data due to hard disk failure. A RAID offers additional
hard disk drives that can avert data loss from a hard disk drive failure. If a hard
drive fails, the RAID volume can regenerate data from the data and parity stored
on its other hard disk drives.
RAID Levels
The NASdeluxe NDL-2400R supports standard RAID levels 0, 1, 5, 6, 10, and
JBOD. You choose a RAID level when you create a system volume. The factors for
selecting a RAID level are:
• Your requirements for performance
• Your need for data security
• Number of hard disk drives in the system, capacity of hard disk drives in
the system
The following is a description of each RAID level:
RAID 0
RAID 0 is best suited for applications that need high bandwidth but do not require
a high level of data security. The RAID 0 level provides the best performance of
all the RAID levels, but it does not provide data redundancy.
RAID 0 uses disk striping and breaking up data into blocks to write across all hard
drives in the volume. The system can then use multiple hard drives for faster
read and write. The stripe size parameter that was set when the RAID was
created determines the size of each block. No parity calculations complicate the
write operation.
RAID 1
RAID 1 mirrors all data from one hard disk drive to a second one hard disk drive,
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 83
thus providing complete data redundancy. However, the cost of data storage
capacity is doubled.
This is excellent for complete data security.
RAID 5
RAID 5 offers data security and it is best suited for networks that perform many
small I/O transactions at the same time, as well as applications that require data
security such as office automation and online customer service. Use it also for
applications with high read requests but low write requests.
RAID 5 includes disk striping at the byte level and parity information is written to
several hard disk drives. If a hard disk fails the system uses parity stored on each
of the other hard disks to recreate all missing information.
RAID 6
RAID 6 is essentially an extension of RAID level 5 which allows for additional fault
tolerance by using a second independent distributed parity scheme (dual parity)
Data is striped on a block level across a set of drives, just like in RAID 5, and a
second set of parity is calculated and written across all the drives; RAID 6
provides for an extremely high data fault tolerance and can sustain two
simultaneous drive failures.
This is a perfect solution for mission critical applications.
RAID 10
RAID 10 is implemented as a striped array whose segments are RAID 1 arrays.
RAID 10 has the same fault tolerance as RAID level 1.
RAID 10 has the same overhead for fault-tolerance as mirroring alone. High I/O
rates are achieved by striping RAID 1 segments.
Under certain circumstances, RAID 10 array can sustain up to 2 simultaneous
drive failures
Excellent solution for applications that would have otherwise gone with RAID 1
but need an additional performance boost.
JBOD
Although a concatenation of disks (also called JBOD, or "Just a Bunch of Disks") is
not one of the numbered RAID levels, it is a popular method for combining
multiple physical disk drives into a single virtual one. As the name implies, disk s
are merely concatenated together, end to beginning, so they appear to be a
single large disk.
As the data on JBOD is not protected, one drive failure could result t otal data loss.
Stripe Size
The length of the data segments being written across multiple hard disks. Data is
written in stripes across the multiple hard disks of a RAID. Since multip le disks
are accessed at the same time, disk striping enhances performance. The stripes
can vary in size.
Disk Usage
When all 5 disks are of the same size, and used in RAID, NDL-2400R disk usage
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 84
percentage is listed below:
RAID Level Percentage Used
RAID 0 100%
RAID 1 20%
RAID 5 80%
RAID 6 60%
RAID 10 50%
JBOD 100%
NOTE
RAID 10 allows only 4 disks and one as spare disk.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 85
Appendix D: Active Directory Basics
Overview
With Windows 2000, Microsoft introduced Active Directory (ADS), which is a large
database/information store. Prior to Active Directory the Windows OS could not
store additional information in its domain database. Active Directory also solved
the problem of locating resources; which previously relied on Network
Neighborhood, and was slow. Managing users and groups were among other
issues Active Directory solved.
What is Active Directory?
Active Directory was built as a scalable, extensible directory service that was
designed to meet corporate needs. A repository for storing user information,
accounts, passwords, printers, computers, network information and other data,
Microsoft calls Active Directory a "namespace" where names can be resolved.
ADS Benefits
ADS lets the NDL-2400R integrate itself with the existing ADS in an office
environment. This means the NDL-2400R is able to recognize your office users
and passwords on the ADS server. Other major benefits ADS support provides
include:
1. Easy integration of the NDL-2400R into the existing office IT infrastructure
The NDL-2400R acts as a member of the ADS. This feature significantly
lowers the overhead of the system administrator. For example, corporate
security policies and user privileges on an ADS server can be enforced
automatically on the NDL-2400R.
2. Centralized user/password database
The NDL-2400R does not maintain its own copy of the user/password
database. This avoids data inconsistency between the NDL-2400R and
other servers. For example, without ADS support, an administrator might
need to remove a specific user privilege on the NDL-2400R and each
individual server. With ADS support, the change on an ADS server is
known to all of its ADS members.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 86
Appendix E: UPS Compatibility List
Brand Series Model Notes
Ablerex MS-RT
ActivePower 1400VA
AEC
MiniGuard UPS 700 M2501
cable
APC
Back-UPS Pro
Matrix-UPS
Smart-UPS
Back-UPS 940-0095A/ C cables, 940-0020B/C cables, 940-0023A cable
Back-UPS Office 940-0119A cable
Masterswitch Not a UPS - 9400020 cable
Back-UPS RS 500 custom nonUSB cable
Belkin
Regulator Pro serial
Resource
Home Office F6H350-SER, F6H500-SER, F6H650-SER
Universal UPS F6C800-UNV, F6C120-UNV, F6C1100-UNV, F6H500ukUNV
Best Power
Fortress (newer)
Fortress Telecom
Axxium Rackmount
Patriot Pro
Patriot Pro II
Patriot INT51 cable
Micro-Ferrups
Fortress/Ferrups f-command
support
Centralion Blazer
Clary ST-800
Compaq T1500h
Cyber Power
Systems
320AVR, 500AVR, 650AVR, 700AVR, 800AVR
850AVR, 900AVR, 1250AVR,. 1500AVR, Power99
550SL, 725SL, CPS825VA, 1100AVR, 1500AVR-HO
Deltec PowerRite Pro II
Dynex 975AVR
Effekta MI/MT/MH 2502 cable
Energy Sistem (various)
ETA mini+UPS WinNT/Upsoft cable
ETA
mini+UPS PRO UPS Explorer
cable
Ever UPS
NET *-DPC
AP *-PRO
Ever-Power 625/1000
Exide NetUPS SE
Fenton
Technologies
PowerPal P-series
PowerPal L-series
PowerOn
PowerPure
Fairstone L525/L625/L750
Fideltronik
Ares 700 and larger
Other Ares models
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 87
Brand Series Model Notes
Fiskars
PowerRite MAX
PowerServer 10, 30
Gamatronic
All models with alarm interface
MP110/210
MS-T
MS
µPS3/1
Gemini UPS625/UPS1000
HP
R3000 XR
R5500 XR
INELT Monolith 1000LT
Infosec iPEL 350, 500, 750, 1000
Ippon (various)
Liebert
UPStation GXT2 contact-closure
cable
Masterguard (various)
Meta System
HF Line 1..4 boards, /2 5..8 boards
HF Millennium 810, 820
HF TOP Line 910, 920, 930, 940, 950, 960, 970, 980
ECO Network
750, M1000, M1050, M1500, M1800
M2000, M2100, M2500, M3000
ECO 305, 308, 311, 511, 516, 519, 522
ally HF 800, 1000, 1250, 1600, 2000, 2500
Megaline 1250, 2500, 3750, 5000, 6250, 7500, 8750, 10000
MGE UPS
SYSTEMS
NOVA AVR 600 Serial
NOVA AVR 1100 Serial
Pulsar Ellipse USBS Serial cable, S, Premium USBS Serial cable, Premium S
Ellipse Office
600 Serial cable, 750 Serial cable, 1000 Serial cable, 1500 Serial
cable
Pulsar EXtreme C / EX RT
Comet EX RT Serial port, 3:1 Serial port
Pulsar Esprit
Evolution S 1250, 1750, 2500, 3000 Serial Port
Pulsar M 2200, 3000, 3000 XL Serial Port
Pulsar
700, 1000, 1500, 1000 RT2U, 1500 RT2U, MX 4000 RT, MX 5000
RT
Serial Port
Evolution, EXtreme C, ES+, ESV+, SV, ESV, EX, EXL, PSX, SX,
Extreme
Comet EXtreme
Comet / Galaxy (Serial) Utalk Serial Card (ref 66060), HID COM Serial Card (ref 66066)
MicroDowell B.Box BP 500, 750, 1000, 1500
Microsol
Solis 1.0 1000VA, 1.5 1500VA, 2.0 2000VA, 3.0 3000VA
Rhino 6.0 6000VA, 7.5 7500VA, 10.0 10000VA, 20.0 20000VA
Mustek
Various
Powermust
400VA Plus, 600VA Plus, 800VA Pro
1000VA Plus, 1400VA Plus, 2000VA USB
Nitram Elite 500, 2002
Oneac
EG/ON Series advanced
interface
Online P-Series
OnLite AQUA 50
Orvaldi various not 400 or 600
Powercom
SMK-800A
ULT-1000
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 88
Brand Series Model Notes
Powercom
TrustTrust 425/625
BNT-1000AP
Advice Partner/King Pr750
BNT-2000AP
PowerGuard PG-600
PowerKinetics 9001
PowerTech Comp1000 DTR cable power
Power Walker Line-Interactive VI1000
Powerware
3110, 3115, 5119, 5125, 5119 RM, PW5115
PW5125PW9120, PW9125, 9120, 9150, 9305
Powerwell
PM525A/-625A/-800A/-1000A/1250A
Repotec
RPF525/625/800/1000
RPT-800A
RPT-162A
SMS (Brazil) Manager III
SOLA 325, 520, 610, 620, 330
SOLA/BASIC
Mexico
various ISBMEX protocol
Socomec
Sicon
Egys 420 VA
Soltec Winmate 525/625/800/1000
Soyntec Sekury C 500, 800
SquareOne
Power
QP1000
SuperPower HP360, Hope-550
Sweex
500/1000 smart - shipped with
SafeNet
500/1000 contact closure shipped with UPSmart
BC100060 800VA
Sysgration UPGUARDS Pro650
Tecnoware Easy Power 1200
Tripp-Lite
SmartUPS
SmartOnline
(various) Lan 2.2 interface black 73-0844 cable
Trust
UPS 1000 Management PW4105
UNITEK Alpha 500 IC, 1000is, 500 ipE
UPSonic
LAN Saver 600
Power Guardian
Victron/IMV
(various)
Lite crack cable
NOTE
• The UPSes marked Blue have been tested and work well
• If your UPS is not in the support list, be sure that the UPS supports
one of following protocols:
o SEC protocol
o Generic RUPS model
o Generic RUPS 2000 (Megatec M2501 cable)
o PhoenixTec protocol
o Safenet software
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 89
Appendix F: Licensing Information
Overview
This product included copyrighted third-party software licensed under the terms
of GNU General Public License. Please see THE GNU General Public License for
extra terms and conditions of this license.
Source Code Availability
NASdeluxe Technology Corp. has exposed the full source code of the GPL licensed
software. For more information on how you can obtain our source code, please
visit our web site, http://www.NASdeluxe.com.
Copyrights
• This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com).
• This product includes software developed by Mark Murray.
• This product includes software developed by Eric Young
(eay@cryptsoft.com).
• This product includes software developed by the OpenSSL Project for use in
the OpenSSL Toolkit (http://www.openssl.org/).
• This product includes PHP, freely available from (http://www.php.net/).
• This product includes software developed by the Un iversity of California,
Berkeley and its contributors.
• This product includes software developed by Winning Strategies, Inc.
• This product includes software developed by the Apache Group for use in
the Apache HTTP server project (http://www.apache.org/).
• This product includes software developed by Softweyr LLC, the University
of California, Berkeley, and its contributors.
• This product includes software developed by Bodo Moeller.
• This product includes software developed by Greg Roelofs and contributors
for the book, "PNG: The Definitive Guide," published by O'Reilly and
Associates.
• This product includes software developed by the NetBSD Foundation, Inc.
and its contributors.
• This product includes software developed by Yen Yen Lim and North Dakota
State University.
• This product includes software developed by the Computer Systems
Engineering Group at Lawrence Berkeley Laboratory.
• This product includes software developed by the Kungliga Tekniska
Högskolan and its contributors.
• This product includes software developed by the Nick Simicich.
• This product includes software written by Tim Hudson (tjh@cryptsoft.com).
• This product includes software developed by Christopher G. Demetriou for
the NetBSD Project.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 90
CGIC License Terms
Basic License
CGIC, copyright 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 by
Thomas Boutell and Boutell.Com, Inc.
Permission is granted to use CGIC in any application, commercial or
noncommercial, at no cost. HOWEVER, this copyright paragraph must appear on
a "credits" page accessible in the public online and offline documentation of the
program. Modified versions of the CGIC library should not be distributed without
the attachment of a clear statement regarding the author of the modifications,
and this notice may in no case be removed. Modifications may also be submitted
to the author for inclusion in the main CGIC distribution.
GNU General Public License
Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.
PREAMBLE
The licenses for most software are designed to take away your freedom to share
and change it. By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change free software--to make sure the
software is free for all its users. This General Public License applies to most of
the Free Software
Foundation's software and to any other program whose authors commit to using
it. (Some other Free Software Foundation software is covered by the GNU Library
General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our
General Public Licenses are designed to make sure that you have the freedom to
distribute copies of free software (and charge for this service if you wish), that
you receive source code or can get it if you want it, that you can change the
software or use pieces of it in new free programs; and that you know you can do
these things.
To protect your rights, we need to make restrictions that forbid anyone to deny
you these rights or to ask you to surrender the rights. These restrictions translate
to certain responsibilities for you if you distribute copies of the software, or if you
modify it.
For example, if you distribute copies of such a program, whether gratis or for a
fee, you must give the recipients all the rights that you have. You must make
sure that they, too, receive or can get the source code. And you must show them
these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer
you this license which gives you legal permission to copy, distribute and/or
modify the software.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 91
Also, for each author's protection and ours, we want to make certain that
everyone understands that there is no warranty for this free software. If the
software is modified by someone else and passed on, we want its recipients to
know that what they have is not the original, so that any problems introduced by
others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish
to avoid the danger that redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary. To prevent this, we
have made it clear that any patent must be licensed for everyone's free use or
not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice
placed by the copyright holder saying it may be distributed under the terms of
this General Public License. The "Program", below, refers to any such
program or work, and a "work based on the Program" means either the
Program or any derivative work under copyright law: that is to say, a work
containing the Program or a portion of it, either verbatim or with modifications
and/or translated into another language. (Hereinafter, translation is included
without limitation in the term "modification". ) Each licensee is addressed as
"you".
Activities other than copying, distribution and modification are not covered by
this License; they are outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered only if its contents
constitute a work based on the Program (independent of having been made
by running the Program).
Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as
you receive it, in any medium, provided that you conspicuou sly and
appropriately publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer to this License
and to the absence of any warranty; and give any other recipients of the
Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may
at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus
forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you
also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that
you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in
part contains or is derived from the Program or any part thereof, to be
licensed as a whole at no charge to all third parties under the terms of this
License.
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 92
c) If the modified program normally reads commands interactively when run,
you must cause it, when started running for such interactive use in the
most ordinary way, to print or display an announcement including an
appropriate copyright notice and a notice that there is no warranty (or else,
saying that you provide a warranty) and that users may redistribute the
program under these conditions, and telling the user how to view a copy of
this License. (Exception: if the Program itself is interactive but does not
normally print such an announcement, your work based on the Program is
not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves, then
this License, and its terms, do not apply to those sections when you distribute
them as separate works. But when you distribute the same sections as part
of a whole which is a work based on the Program, the distribution of the whole
must be on the terms of this License, whose permissions for other licensees
extend to the entire whole, and thus to each and every part regardless of who
wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to
work written entirely by you; rather, the intent is to exercise the right to
control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with
the Program (or with a work based on the Program) on a volume of a storage
or distribution medium does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work based on it, under
Section 2) in object code or executable form under the terms of Sections 1
and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source
code, which must be distributed under the terms of Sections 1 and 2 above on
a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give
any third party, for a charge no more than your cost of physically performing
source distribution, a complete machine-readable copy of the corresponding
source code, to be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as t o the off er to
distribute corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object
code or executable form with such an offer, in accord with Subsection b
above.)
The source code for a work means the preferred form of the work for making
modifications to it. For an executable work, complete source code means all
the source code for all modules it contains, plus any associated interface
definition files, plus the scripts used to control compilation and installation of
the executable. However, as a special exception, the source code distributed
need not include anything that is normally distributed (in either source or
binary form) with the major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless that component itself
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 93
accompanies the executable.
If distribution of executable or object code is made by offering access to copy
from a designated place, then offering equivalent access to copy the source
code from the same place counts as distribution of the source code, even
though third parties are not compelled to copy the source along with the
object code.
4. You may not copy, modify, sublicense, or distribute the Program except as
expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate
your rights under this License. However, parties who have received copies, or
rights, from you under this License will not have their licenses terminated so
long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it.
However, nothing else grants you permission to modify or distribute the
Program or its derivative works. These actions are prohibited by law if you do
not accept this License. Therefore, by modifying or distributing the Program
(or any work based on the Program), you indicate your acceptance of this
License to do so, and all its terms and conditions for copying, distributing or
modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program),
the recipient automatically receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms and conditions. You
may not impose any further restrictions on the recipients' exercise of the
rights granted herein. You are not responsible for enforcing compliance by
third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement
or for any other reason (not limited to patent issues), conditions are imposed
on you (whether by court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from the con ditions of this
License. If you cannot distribute so as to satisfy simultaneously your
obligations under this License and any other pertinent obligations, then as a
consequence you may not distribute the Program at all. For example, if a
patent license would not permit royalty-free redistribution of the Program by
all those who receive copies directly or indirectly through you, then the only
way you could satisfy both it and this License would be to refrain entirely from
distribution of the Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or
other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software
distribution system, which is implemented by public license practices. Many
people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee cannot impose
that choice.
This section is intended to make thoroughly clear what is believed to be a
NASdeluxe NDL-2400R iSCSI/NAS System - Manual
www.NASdeluxe.com
Page 94
consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries
either by patents or by copyrighted interfaces, the original copyright holder
who places the Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the
General Public License from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to address new problems
or concerns.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and "any later
version", you have the option of following the terms and conditions either of
that version or of any later version published by the Free Software Found ation.
If the Program does not specify a version number of this License, you may
choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs
whose distribution conditions are different, write to the author to ask for
permission. For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we sometimes make
exceptions for this. Our decision will be guided by the two goals of preserving
the free status of all derivatives of our free software and of promoting the
sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE
LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PAR TIES PROVIDE THE PROGRAM "AS IS"
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH
YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF
ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN
WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY
MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED
BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
Loading...