Nascom NC1010TW-STFB, NC1010TW-SW, NC1010TW-SWFB, NC1010TW-ST, NC1010TW-M Specsheet
...
NC1010T
MINI SCREW TERMINAL SWITCH AND MAGNET SET WITH SNAP ON COVERS
DESCRIPTION
Nascom’s NC1010T is a mini surface mount screw terminal wide gap switch and
magnet set set with breakoff screw hole mounting tabs.
The NC1010T is the installer’s choice of contact conguration because the contact
set is designed to cut installation times and helps to prevent false alarms caused
by shifting or warping doors and windows.
The NC1010T Series is designed for vinyl, wood or aluminum doors and windows.
FEATURES
• QUICK CONNECT, EASY TO INSTALL • 3M VHB (Very High Bond) DOUBLE SIDED TAPE
• SCREW TERMINALS • LOW PROFILE DESIGN
• WIDE GAP - N35 NdFeB RARE EARTH MAGNET • SNAP-ON COVERS
• BREAKAWAY FLANGE • LISTED TO UL634 STANDARD
ORDERING INFORMATION
CONTACT RATING
PART
NUMBER
COLOR
OPERATE
GAP
(in inches)
(Max DC/Peak AC Resistive)
SWITCHING CARRY
V I V I
CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:
NC1010TB/ST
NC1010TG/ST
NC1010TT/ST
NC1010TW/ST
BROWN
GREY
TAN
WHIITE
0.75 to
1.1125
200 VDC 0.5 Amps 10vA 1.5 Amps 150 mOhms
OPEN LOOP, NORMALLY CLOSED, 1FB, SWITCH/MAGNET SET:
NC1010TB/STFB
NC1010TG/STFB
NC1010TT/STFB
NC1010TW/STFB
BROWN
GREY
TAN
WHIITE
0.65 to 1.10 30 VDC 0.2 Amps 3vA 0.5 Amps 150 mOhms
WIRING SCHEMATIC
SWITCH
CONTACT
CLOSED LOOP,
NORMALLY OPEN CONTACT
OPEN LOOP,
NORMALLY CLOSED CONTACT
SWITCH
CONTACT
STATIC
CONTACT
RESISTANCE
(50mV, 100mA)
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
|
F: 800.727.4041
|
www.nascominc.com
DWG No. 120717-02 Rev. 1
1
1.96
TYP.
49.78
3M VHB TAPE
2X
.25
6.35
TOP
FRONT
.28
TYP.
7.11
.33
TYP.
8.38
3M VHB TAPE
.38
TYP.
9.53
1.75
TYP.
44.32
2X
.10
TYP.
2.41
TOP
FRONT
DIMENSIONS - IN [mm]
.34
8.64
.42
10.54
.15
3.81
.48
12.07
2.06
52.32
TOP
FRONT
NC1010T
MINI SCREW TERMINAL SWITCH AND MAGNET SET WITH SNAP ON COVERS
SWITCH
MAGNET
COVER
INSTALLATION INSTRUCTIONS
This switch and magnet set can be fastened using #4 round head wood screws or pan head sheet metal screws. The switch
and magnet housings feature a break away ange that can be removed if desired for tape mounting only. The installation
instructions refer to the more common mounting method using the supplied 3M VHB tape.
• Pre-t the switch and magnet in the desired location on the window. When mounting, be sure to allow enough clearance
between the switch and magnet for the snap on covers.
• Clean the mounting surface area for both switch and magnet with alcohol and let dry.
• Remove the liner from the tape on the back of the switch and carefully position the switch on the window frame as close
as possible to the movable part of the window.
• Remove the liner from the tape on the back of the magnet and carefully align the magnet parallel with the switch on the
movable part of the window.
• Apply rm pressure to the switch and magnet housing to ensure proper adhesion to the mounting surface.
• Test alarm system for correct operation.
• Snap the covers on the switch and magnet.
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
|
F: 800.727.4041
|
www.nascominc.com
DWG No. 120717-02 Rev. 1
2
Loading...