Nascom N1178TSHK-STDD, N1178GSHK-STHS, N1178WSHK-STSD, N1178WSHK-STHS, N1178WSHK-STFB Specsheet

...
N1178 SHK
1” RECESSED STUBBY DOOR CONTACT WITH SHARK MAGNET
DESCRIPTION
Nascom’s N1178 SHK Series is a 1” recessed stubby door contact couple with the patented SHARKTM magnet. The set is designed for residential, com­mercial and industrial steel and wood door applications.
The N1178 SHK is the installer’s choice of contact conguration because the
contact set is designed to cut installation times .. just a pinch of the springs in­stalls the SHARKTM magnet permanently and the powerful rare earth magnet helps to prevent false alarms caused by shifting or warping doors.
The N1178 SHK Series is designed for installation in every type of hinged door including wood doors.
FEATURES
TIME SAVING INSTALLATION NO SILICONE REQUIRED FOR MAGNET INSTALL
12” 22AWG WIRE LEADS POLYPROPYLENE SWITCH HOUSING
WIDE GAP - N35 NdFeB RARE EARTH MAGNET LISTED TO UL634 STANDARD
ORDERING INFORMATION
CONTACT RATING
PART
NUMBER
COLOR
OPERATE
GAP
(in inches)
(Max DC/Peak AC Resistive)
SWITCHING CARRY
V I V I
CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:
N1178BSHK/ST N1178GSHK/ST N1178TSHK/ST N1178WSHK/ST
BROWN GREY TAN WHITE
0.75 to 1.25 200 VDC 0.5 Amps 10vA 1.5 Amps 150 mOhms
DUAL CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:
N1178BSHK/ST2CR N1178GSHK/ST2CR N1178TSHK/ST2CR N1178WSHK/ST2CR
BROWN GREY TAN WHITE
0.75 to 1.25 200 VDC 0.5 Amps 10vA 1.5 Amps 150 mOhms
OPEN LOOP, NORMALLY CLOSED, 1FB, SWITCH/MAGNET SET:
N1178BSHK/STFB N1178GSHK/STFB N1178TSHK/STFB N1178WSHK/STFB
BROWN GREY TAN WHITE
0.75 to 1.25 30 VDC 0.2 Amps 3vA 0.5 Amps 150 mOhms
SINGLE POLE DOUBLE THROW, SWITCH/MAGNET SET:
N1178BSHK/STSD N1178GSHK/STSD N1178TSHK/STSD N1178WSHK/STSD
BROWN GREY TAN WHITE
0.75 to 1.25 30 VDC 0.2 Amps 3vA 0.5 Amps 150 mOhms
DOUBLE POLE DOUBLE THROW, SWITCH/MAGNET SET:
N1178B/STDD N1178G/STDD N1178T/STDD N1178W/STDD
BROWN GREY TAN WHITE
0.75 to 1.25 30 VDC 0.2 Amps 3vA 0.5 Amps 150 mOhms
HIGH SECURITY, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:
N1178BSHK/STHS N1178GSHK/STHS N1178TSHK/STHS N1178WSHK/STHS
BROWN GREY TAN WHITE
0.1875 to
0.5000
300 VDC
0.25
Amps
10vA
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
|
F: 800.727.4041
0.25
Amps
|
STATIC
CONTACT
RESISTANCE
(50mV, 100mA)
150 mOhms
initial
DWG No. 131123-09 Rev. 1
www.nascominc.com
1
.800
20.32
.060
1.52
.375
9.53
.480
12.19
.730
18.54
.910
23.11
FRONT VIEW
TOP VIEW
.375
9.53
1.600
40.64
1.507
38.27
1.119
28.42
WIRING SCHEMATIC
N1178 SHK
1” RECESSED STUBBY DOOR CONTACT WITH SHARK MAGNET
” RECESSED STUBBY DOOR CONTACT WITH SHARK MAGNET
SWITCH CONTACT
CLOSED LOOP, NORMALLY OPEN CONTACT
COMMON (BROWN)
COMMON (BROWN)
OPEN LOOP, NORMALLY CLOSED CONTACT
NC, OPEN LOOP (WHITE)
NO, CLOSED LOOP (RED) NC, OPEN LOOP (WHITE)
NC, OPEN LOOP (RED)
SWITCH CONTACT
COMMON (BROWN)
DUAL CLOSED LOOP, NORMALLY OPEN CONTACTS
DPDT, DOUBLE POLE DOUBLE THROW SPDT, SINGLE POLE DOUBLE THROW
DIMENSIONS - IN [mm]
NC, OPEN LOOP (WHITE)
NO, CLOSED LOOP (RED)
SWITCH
MAGNET
INSTALLATION INSTRUCTIONS
Mark location for the switch on the door frame.
Drill a hole for the switch using a 1” Hole Saw for steel doors or a Forstner bit for wood doors.
Connect the switch leads to the alarm circuit conductors. Hold the wire leads (not the switch housing) when cutting and stripping to prevent damage to the switch.
Feed the switch conductors into the hole and insert the switch housing pressing rmly until seated. Silicone may be used to secure the switch in wood doors.
Test switch for correct operation and make sure gap performance is acceptable.
Place a mark on the top edge of the door aligned with the center of the switch.
Press the springs inward on the sides of magnet.
Insert the magnet in u-channel in the top of the door centered with the alignment mark.
Release the springs to secure the magnet and complete the installation.
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
|
F: 800.727.4041
|
www.nascominc.com
DWG No. 131123-09 Rev. 1
2
Loading...
+ 1 hidden pages