Nascom N1175600G-ST, N1175600W-STFB, N1175600W-ST2CR, N1175600W-ST, N1175600T-STFB Specsheet

...

N1175 600

3/8” RECESSED MINI CONTACT WITH NdFeB 0.600” DOUGHNUT MAGNET

DESCRIPTION

Nascom’s N1175 600 Series, mini 3/8” recessed contact with an NdFeB

0.600” doughnut magnet, protects all nonferrous (e.g. wood, aluminum and vinyl) doors and windows, in both residential and commercial settings.

The N1175 600 is the installer’s choice of contact conguration where drill

depth is critical and excellent air and side-to-side gap are required to prevent false alarms caused by shifting or warping doors and windows due.

FEATURES

• PRESS FIT - NO GLUE REQUIRED • ENCAPSULATED HERMETICALLY SEALED CONTACTS

• 12” 22AWG WIRE LEADS • POLYPROPYLENE HOUSINGS

• WIDE GAP - N35 NdFeB RARE EARTH MAGNET • LISTED TO UL634 STANDARD

ORDERING INFORMATION

CONTACT RATING

PART

NUMBER

COLOR

OPERATE

GAP

(in inches)

(Max DC/Peak AC Resistive)

SWITCHING CARRY

V I V I

CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:

N1175600B/ST N1175600G/ST N1175600W/ST

HIGH SECURITY, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:

N1175600B/STHS N1175600G/STHS N1175600W/STHS

BROWN GREY WHIITE

0.75 to 1.125 200 VDC 0.5 Amps 10vA 1.5 Amps 150 mOhms

0.1875 to 0.50 300 VDC

0.20

Amps

3vA 0.5 Amps

STATIC

CONTACT

RESISTANCE

(50mV, 100mA)

150 mOhms

initial

WIRING SCHEMATIC

SWITCH CONTACT

CLOSED LOOP, NORMALLY OPEN CONTACT

Royne Industries LLC, dba NASCOM

P: 800.843.5530

F: 800.727.4041

www.nascominc.com

DWG No. 131119-07 Rev. 1

.680

17.27

.030

0.76

.465

11.81

.355

9.02

FRONT VIEW

TOP VIEW

.300

x 82

.600

.125

82.00°

.010

TYP ALL EDGES

SECTION A-A

DIMENSIONS - IN [mm]

N1175 600

3/8” RECESSED MINI CONTACT WITH NdFeB 0.600” DOUGHNUT MAGNET

SWITCH

MAGNET

INSTALLATION INSTRUCTIONS

• Mark location for the switch on the door frame and mark the location for the magnet on the top edge of the door.

• Make sure switch and magnet hole locations are aligned.

• Using a square, transfer the marks on to the top edge of the door and the opposing door frame.

• Using a tape measure or graduations on the square, locate the center of the door edge and place an intersecting line with

the rst mark. Mount the donut magnet using the #4X1/2 athead screw provided.

• Repeat the above step to locate the hole position for the switch in the door frame. Drill a 3/8” hole in the door frame.

• Connect the switch leads to the alarm system. Caution! Hold wire leads, not the switch housing while cutting and

stripping to prevent damage to switch.

• Insert wire leads into hole followed by the switch and press the switch into the hole until the head is ush with the door

frame

• Test switch for correct operation and make sure gap performance is acceptable.

Royne Industries LLC, dba NASCOM

P: 800.843.5530

F: 800.727.4041

www.nascominc.com

DWG No. 131119-07 Rev. 1

+ 1 hidden pages