Napoleon grills BUILT-IN PF UNIT INSTRUCTION GUIDE

SERIAL #______________________
BUILT-IN PF UNIT INSTRUCTION GUIDE
Please use this manual in conjuction with your main manual to properly assemble your built-in grill. Refer to the main manual for operat­ing, cleaning, and maintenance instructions. The operating instructions are also located on the bottom of the side burner lid. This grill is designed for masonry, non-combustible enclosures only, and must be installed and serviced by a qualified installer to local codes.
BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane Installation Code in Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2" for rigid pipe, and 5/8" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with CAN B149.1. Propane Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States. If the enclo­sure is to house a propane cylinder, the tank portion of the enclosure must be ventilated according to local codes, and must not have communication with the cavity used to enclose the gas grill. The tank can not be stored below the gas grill.
BUILT IN NATURAL GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane Installation Code in Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2" for rigid pipe, and 3/4" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with CAN B149.1. Natural Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United S tates.
Built in units are supplied with a drip pan which holds only a minimal amount of grease. T oprevent grease fires, the panmust be cleaned after each use. Access must be provided to the inside of the enclosure to make gas connections.
OPENINGDIMENSIONS
34”
RECOMMENDED
8 ¼
20 e
7”
ELECTRICALWIREACCESS
OPENING(4”x4”)
8 f
55¾PF600 UNITS 46¾” PF450 UNITS
2”MIN
GASINLET OPENING
(4”x4”)
6”
4”
ELECTRICALBOX
OPENING
8 ¼
CENTEROF ELECTRICALBOX MUSTBE WITHIN3
FEETOF LEFTEDGE OFGAS GRILL
MINIMUM10 SQIN OFVENTILATION
REQUIREDON EACHENDOFCABINET
N415-0111/NOV29/05
BUILT -INACCESSORYOPENING DIMENSIONS
NOTE:ACCESSORYFRAMES OVERLAP
OPENINGBY 1½” ONALL 4SIDES
D
H
W
Part #
N370-0069 Flat vertical painted door
N370-0071
N370-0070
N370-0072
N370-0356SS Curved stainless steel door - 308 size
Flat vertical stainless steel door
Flat horizontal painted door
Flat horizontal stainless steel door
Description
Picture
OPENINGDIMENSION
WH
13¼”
18¼”
D
13¼” 18¼”
18¼” 13 ¼”
18¼” 13 ¼”
22½” 19 ¾”
N370-0357SS
N370-0358SS
N370-0361 PF style stainless steel door
N370-0359 PF style stainless steel single drawer
N370-0360 PF style stainless steel triple drawer
Curved stainless steel door - 450 size
Curved stainless steel double door - 600 size
27” 19 ¾”
35¼” 19
17”
23¼”
17¼” 6 ¾”
17¼” 22 ¾”
23
23
Loading...
+ 2 hidden pages