Napoleon LV50N, LV50N2, LV50P2, LV50P Installation And Operating Instructions Manual

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: ANSI Z21.50 ● CSA 2.22 FOR VENTED GAS APPLIANCES.

CONFORMS TO AMERICAN NATIONAL STANDARDS: ANSI Z21.50, CERTIFIED TO CANADIAN CSA 2.22 FOR VENTED GAS FIREPLACES.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

SAFETY INFORMATION

WARNING

If the information in these instructions are not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

- Installation and service must be performed by a

qualiﬁ ed installer, service agency or the supplier.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

Decorative Product: Not for use as a heating appliance.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

LV50N / LV50N2

NATURAL GAS

LV50P / LV50P2

PROPANE

SAFETY BARRIER

SEE-THRU ILLUSTRATED

DANGER

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

FR PG 69

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonﬁ replaces.com • hearth@napoleonproducts.com

$10.00

BARRIER

1.22D

W415-1439 / A / 07.10.15

NOTE: The camera icon indicates video tutorials are available as additional reference, visit http://www.napoleonﬁ replaces.com/category/product-support/support-centre/

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

3.0 VENTING 9

4.0 INSTALLATION 18

5.0 FRAMING 24

6.0 FINISHING 37

7.0 ELECTRICAL CONNECTION 42

8.0 OPERATION 45

9.0 OPERATING INSTRUCTIONS 49

10.0 ADJUSTMENT 50

11.0 MAINTENANCE 52

12.0 REPLACEMENTS 58

13.0 OVERVIEW 59

14.0 BURNER 60

15.0 ACCESSORIES 61

16.0 TROUBLESHOOTING 62

17.0 WARRANTY 65

18.0 SERVICE HISTORY 66

19.0 NOTES 67

W415-1439 / A / 07.10.15

2.1 DIMENSIONS 5

2.2 GENERAL INSTRUCTIONS 6

2.3 GENERAL INFORMATION 7

2.4 RATING PLATE / LIGHTING INSTRUCTION LOCATION 8

3.1 VENTING LENGTHS AND COMPONENTS FOR DIRECT VENT INSTALLATIONS 9

3.2 TYPICAL VENT INSTALLATIONS 10

3.3 SPECIAL VENT INSTALLATION 11

3.3.1 PERISCOPE TERMINATION 11

3.4 MINIMUM AIR TERMINAL LOCATION CLEARANCES 12

3.5 VENT APPLICATION FLOW CHART 13

3.6 DEFINITIONS 13

3.7 ELBOW VENT LENGTH VALUES 13

3.8 HORIZONTAL TERMINATION 14

3.9 VERTICAL TERMINATION 16

4.1 WALL AND CEILING PROTECTION 18

4.1.1 HORIZONTAL INSTALLATION 19

4.1.2 VERTICAL INSTALLATION 19

4.2 USING FLEXIBLE VENT COMPONENTS 20

4.2.1 HORIZONTAL AIR TERMINAL INSTALLATION 20

4.2.2 VERTICAL AIR TERMINAL INSTALLATION 21

4.2.3 APPLIANCE VENT CONNECTION 22

4.3 MOBILE HOME INSTALLATION 22

4.4 GAS INSTALLATION 23

5.1 TWO SIDED APPLIANCE 26

5.2 ONE SIDE APPLIANCE 28

5.3 MINIMUM CLEARANCE TO COMBUSTIBLE ENCLOSURES 30

5.4 VENTILATION OPENINGS AND ENCLOSURE CLEARANCES 32

5.5 INSTALLING NON-COMBUSTIBLE BOARD 33

5.6 RECESSED INSTALLATION 35

5.7 MINIMUM COMBUSTIBLE MANTEL CLEARANCES 36

6.1 SAFETY SCREEN INSTALLATION / REMOVAL 38

6.2 DOOR INSTALLATION / REMOVAL 39

6.3 GLASS MEDIA INSTALLATION 40

6.4 OPTIONAL ROCK / DRIFTWOOD PLACEMENT 41

6.5 LOGO PLACEMENT 41

7.1 HARD WIRING CONNECTION 42

7.2 RECEPTACLE WIRING DIAGRAM 43

7.3 REMOTE RECEIVER INSTALLATION 43

7.4 SCHEMATIC 44

8.1 GENERAL TRANSMITTER LAYOUT 45

8.4 INITIALIZING THE TRANSMITTER/BATTERY HOLDER FOR THE FIRST TIME 46

8.2 TEMPERATURE DISPLAY 46

8.3 FLAME HEIGHT 46

8.5 LED ON/OFF LIGHT CONTROL 47

8.6 CONTINUOUS PILOT / INTERMITTENT PILOT (CPI / IPI) SELECTION 48

8.7 CHILD PROOF FUNCTION 48

8.8 LOW BATTERY / MANUAL BYPASS 48

8.9 IN THE EVENT OF A POWER FAILURE 48

8.10 TIMED BLOWER 49

10.1 RESTRICTING VERTICAL VENTS 50

10.2 PILOT BURNER ADJUSTMENT 50

10.3 VENTURI ADJUSTMENT 51

10.4 FLAME CHARACTERISTICS 51

11.1 ANNUAL MAINTENANCE 53

11.2 CONTROL ACCESS 53

11.3 VALVE REMOVAL 54

11.4 BURNER REMOVAL 55

11.5 CONTROL MODULE REMOVAL 55

11.6 LED REPLACEMENT 56

11.7 GLASS / DOOR REPLACEMENT 57

11.8 CARE OF GLASS 57

11.9 CARE OF PLATED PARTS 57

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INSTALLATION OVERVIEW

See the section “FRAMING MINIMUM MANTEL CLEARANCES”

See the section “FRAMING MINIMUM CLEARANCE TO COMBUSTIBLE ENCLOSURES” for drywall (or other combustible material)”

See the section “FRAMING”

See the section “RATING PLATE / LIGHTING INSTRUCTION LOCATION”

Side Wall

See the section “ANTI CONDENSATION CONTROL SWITCH”

See the section “VENTING - VENTING LENGTHS AND AIR TERMINAL LOCATIONS”

SAFETY BARRIER

See the section “FRAMING MINIMUM CLEARANCE TO COMBUSTIBLE ENSLOSURES” for noncombustible materials such as tile, marble, granite, etc. Important: Extra support may be required

See the section “CONTROL ACCESS” for the control box.

See the section “REMOTE RECEIVER INSTALLATION”.

NOTE: A ventilated enclosure is required. See “VENTILATION OPENINGS” section

W415-1439 / A / 07.10.15

2.0 INTRODUCTION

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND IS PROHIBITED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause ﬁ re or injury.

• Risk of ﬁ re or asphyxiation do not operate appliance with ﬁ xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to

avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to operating the appliance.

• The appliance is a vented gas-ﬁ red appliance. Do not burn wood or other materials in the appliance

• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance and venting system are kept clean. The appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these openings can also cause the surrounding combustible materials to overheat and catch ﬁ re.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these are not toys and should be kept away from children and infants.

• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage of decorations, a T.V. or other electronic components.

• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed.

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

WARNING

3.2C

W415-1439 / A / 07.10.15

2.1 DIMENSIONS

FRONT VIEW

SAFETY BARRIER

TOP VIEW

66 13/16"

1698mm

SIDE VIEW

52 5/16"

1329mm

17 1/4"

438mm

1270mm

50"

SEE-THRU

FRONT VIEW

SAFETY BARRIER

TOP VIEW

52 5/16"

1329mm

SIDE VIEW

50"

1270mm

22 13/16"

579mm

66 13/16"

1698mm

SINGLE SIDED

W415-1439 / A / 07.10.15

2.2 GENERAL INSTRUCTIONS

WARNING

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,

WITH THE GLASS DOOR OPENED OR REMOVED.

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

PROVIDE ADEQUA TE VENTILA TION.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” (1219mm) FROM

THE FRONT FACE OF THE APPLIANCE.

SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT

WHEN THE APPLIANCE IS OPERATING.

FIRE RISK. EXPLOSION HAZARD.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE

TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG (35 mb).

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.

USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING

COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.

THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for example in Massachusetts State:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (914mm).

• A Carbon Monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.

The installation must conform with local codes or, in absence of local codes, the National Gas and Propane Installation Code CSA B149.1 in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States. Suitable for mobile home installation if installed in accordance with the current standard CAN/CSA Z240MH Series, for gas equipped mobile homes, in Canada or

NSI Z223.1 and NFPA 54 in the United States.

s long as the required clearance to combustibles is maintained, the most desirable and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat created. The location of windows, doors and the trafﬁ c ﬂ ow in the room where the appliance is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or roof joist.

If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.

Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian

Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.

www.ncertied.org

We suggest that our gas hearth products be installed and serviced by professionals who are certied in the U.S. by the National Fireplace

Institute

(NFI) as NFI Gas

Specialists

4.1B

W415-1439 / A / 07.10.15

2.3 GENERAL INFORMATION

FOR YOUR SA TISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERA TION AND QUALITY!

LV50N LV50N2

Altitude (FT) 0-4,500 0-4500 0-4,500 0-4500

Max. Input (BTU/HR) 40,000 40,000 40,000 40,000

Min. Input (BTU/HR) 26,000 32,000 26,000 32,000

P4 49% 49% 54% 54%

NG LP NG LP

Min. Inlet Gas Supply Pressure

Max. Inlet Gas Supply Pressure

Manifold Pressure (Under Flow Conditions)

When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speciﬁ c recommendations from the local authority having jurisdiction, the certiﬁ ed high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft (305m). Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected. Change in ﬂ ame appearance from “HI” to “LO” is more evident in natural gas than in propane.

This appliance is approved for bathroom, bedroom and bed-sitting room installations and is certiﬁ ed for mobile home installation.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

There are two switches that control the function of the appliance. One on the receiver that must be placed in the middle position. The other is on the control module that must be in the “I” position, which denotes on. If these switches aren’t in these locations the appliance will not work, see “REMOTE RECEIVER INSTALLATION” and “CONTROL MODULE” section.

4.5" wc (11mb) 11" wc (27mb) 4.5" wc (11mb) 11" wc (27mb)

7" wc (17mb) 13" wc (32mb) 7" wc (17mb) 13" wc (32mb)

3.5" wc (9mb) 10" wc (25mb) 3.5" wc (9mb) 10" wc (25mb)

NOTE: The protective wrap on plated parts is best removed when the assembly is at room temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat source.

This appliance is equipped with a remote control system, which requires batteries to be installed. The transmitter takes 3 “AAA” batteries and in the case of a power failure the receiver takes 4 “AA” batteries.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance and must be installed.

W415-1439 / A / 07.10.15

40MH SERIES GAS EQUIPPED MOBILE HOMES,0MH SERIES GAS EQUIPPED MOBILE HOMES

PART 3280. WHEN THIS US STANDARD IS NOT ART 3280. WHEN THIS US STANDARD IS NOT

INSTALLATION CODES. ON CODES.

FOR USE WITH BARRIER W565-01USE WITH BARRIER W565

FOYFO

9700

LV50N LV50N

CLV

0-4500FT (00-4500F

404

0" RECESSED 0" RECESSED

0" RECESSE

5 INCHES W.C. (NG)

COLO

)COLONNE D'EA

4.5" W.C.(NG) 4.5" W

4.5" D'UNE4

COLONNE D'EAU (GN)COLONNE D'EAU (GN)

AX. SUPPLY PRESSURE:

X. SUPPLY PRESSURE:

) 7" W.C. (NG)

7" D'UNE

COLO

)COLONNE D'EAU (GN)

RACKED

EMENT OF

D BE DONE

ver

lisé uniquemen

qués sur la plaque

allé dans une

uée (É.-U. seulement) ou

le permettent.

oir la notice de

eur pour plus de renseignements. Une

appareil.»

VOT

AS ENTREPOSER NI UTILISER

ENCE NI D’AUTRES

APEURS

QUIDES INFLAMMABLES

E VOISINAGE DE CET

OU DE TAU

AREIL.

TISSE

ILISER

ANNEAU FRO

AS EN

2.4 RATING PLATE / LIGHTING INSTRUCTION LOCATION

WARNING

ALLOW THE APPLIANCE TO COOL BEFORE PERFORMING ANY MAINTENANCE OR CLEANING.

Both the rating plate and lighting instructions are attached to a key chain located on the left side of the control area near the valve. Remove the front to gain access to the control area, refer to the “SAFETY SCREEN INSTALLATION / REMOVAL” section for detailed removal instructions.

To replace, slide the instructions back into the control area and reinstall the safety screen assembly.

KEEP BURNER AND CONTROL

COMPARTMENT CLEAN. SEE

INSTALLATION AND OPERA TING

INSTRUCTIONS MANUAL.

APPLIANCE NEEDS FRESH

AIR FOR SAFE OPERATION

AND MUST BE INSTALLED

WITH ADEQUATE PROVISIONS

FOR COMBUSTION

AND VENTILATION AIR.

GARDEZ LE BRULEUR ET LE

COMPARTIMENT DES

CONTROLES PROPRES.

CONSULTEZ LE MANUEL

D’INFORMATION ET

D’INSTALLATION. PAR

MESURE DE SECURITE.

CET APPAREIL DOIT

ETRE ALIMENTE EN AIR

FRAIS ET AVEC SUFFISANT

D’AIR COMBURANTET

DE VENTILATION.

WARNING:

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE

CAN CAUSE PROPERTY DAMAGE,

PERSONAL INJURY OR LOSS OF

LIFE. REFER TO OWNER’S

MANUAL. INSTALLATION AND

SERVICE MUST BE PERFORMED

BY A QUALIFIED INSTALLER,

SERVICE AGENCY OR THE

GAS SUPPLIER.

ATTENTION:

UN INSTALLATION OU UNE

MODIFICATION INAPPROPRIEE DU REGLAGE, DU SERVICE ET DE L’ENTRETIEN POURRAIENT ETRE

LA CAUSE DE DOMMAGES A LA

PROPRIETE DE BLESSURES CORPORELLES OU MEME LA

MORT. CONSULTER LE MANUEL

D’INFORMATION, L’INSTALLATION

ET LE SERVICE DOIVENT

ETRE EXECUTES PAR UN

INSTALLATEUR QUALIFIE POUR

LE AZ, UNE ENTREPRISE DE

SERVICE OU LE FOURNISSEUR

DE GAZ SEULEMENT.

CAUTION:

HOT WHILE OPERATING. DO NOT TOUCH. KEEP CHILDREN, CLOTHING, FURNITURE,

GASOLINE OR OTHER FLAMMABLE VAPORS

AWAY.

AVERTISSEMENT:

L’APPAREIL EST CHAUD PENDANT SON FONCTIONNEMENT. LES ENFANTS, LES

VETEMENTS, LES MEUBLES, L’ESSENCE ET

AUTRES LIQUIDES QUI EMETTENT DES GAZ

VOLATILS INFLAMMABLES DOIVENT

ETRE TENUS ELOIGNES DE L’APPAREIL.

“This appliance is only for use with the type(s)

of gas indicated on the rating plate and may

be installed in an aftermarket, permanently

located, manufactured home (USA only) or mobile home, where not prohibited by local codes. See owner’s manual for details. This appliance is supplied with a conversion kit.”

«Cet appareil doit être utilisé uniquement

avec les types de gaz indiqués sur la plaque

signalétique et peut être installé dans une

maison préfabriquée (É.-U. seulement) ou

mobile installée à demeure si les règlements

locaux le permettent. Voir la notice de

l’utilisateur pour plus de renseignements. Une

trousse de conversion est fournie avec cet

appareil.»

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE

OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN VICINITY OF THIS

OR ANY OTHER APPLIANCE.

CAUTION: DO NOT OPERATE

THE FIREPLACE WITH THE GLASS REMOVED, CRACKED OR BROKEN.

REPLACEMENT OF THE GLASS

SHOULD BE DONE BY A LICENSED

OR QUALIFIED PERSON.

POUR VOTRE

SECURITE:

NE PAS ENTREPOSER NI UTILISER

D’ESSENCE NI D’AUTRES VAPEURS

OU LIQUIDES INFLAMMABLES

ANS LE VOISINAGE DE CET

APPAREIL OU DE TOUT AUTRE

APPAREIL.

AVERTISSEMENT: NE PAS

UTILISER L’APPAREIL SI LE

PANNEAU FRONTAL EN VERRE

N’EST PAS EN PLACE, EST CRAQUÉ

OU BRISÉ. CONFIEZ LE

REMPLACEMENT DU

PANNEAU À UN

TECHNICIEN

AGRÉÉ.

ATION IF INSTALLED IN ACCORDANCE WITH THE

IO. APPROPRIÉ POUR INSTALLATION DANS UNE

UN COMBUSTIBLE SOLIDE NE

S, SITES AND COMMUNITIES, ANSI / NFPA 501A.

N VIGUEUR AU CANADA OU AUX ÉTATS-UNIS DE LA

LES COMMUNAUTÉS, ANSI/NFPA 501A.

- 2008 VENTED GAS FIREPLACE HEATER / APPAREIL DE CHAUFFAGE ALIMENTÉ b

MODEL PROPANE

- 2008, ANSI Z21.88 b

GAZ NATURAL

MODEL NATURAL GAS /

VENTED GAS FIREPLACE HEATER. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALL CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24 CFR,

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA 2.33

PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATION

AU GAZ ET VENTILÉ

FOYER DE CHAUFFAGE AU GAZ AVEC ÉVACUATION. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE SALLE DE BAIN ET UN STUD

MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉES AU GAZ, E

NORME DE SECURITÉ ET DE CONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ÉTATS-UNIS NE PEUT ÊTRE APPLIQUÉE, SE RÉFÉRER A LA NORME RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES SITES ET

W/N 16131

REFERENCE #

NOT FOR USE WITH

SOLID FUEL. FOR USE

DOIT PAS ÊTRÉ UTILISÉ AVEC

LHD50PT

WITH GLASS DOORS

CET APPAREIL. UTILISER AVEC LES PORTES VITRÉES

HOMOLOGUÉES SEULEMENT

AVEC CETTE UNITÉ.

0-4500FT (0-1370M)

30,000 BTU/H

ALTITUDE / ÉLÉVATION INPUT / ALIMENTATION

REDUCED INPUT / ALIMENTATION RÉDUITE

30,000 BTU/H

23,000 BTU/H

0-4500FT (0-1370M)

LHD50NT

DO NOT ADD ANY MATERIAL

CERTIFIED WITH THIS UNIT ONLY.

WARNING

TO THE APPLIANCE, WHICH WILL COME

AVERTISSEMENT:

23,000 BTU/H #53

ORIFICE / INJECTEUR

#38

3.5" WATER COLUMN/D'UNE COLONNE D'EAU

IN CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE

N'AJOUTEZ PAS A

CET APPAREIL AUCUN MATÉRIAU DEVANT ENTRER EN CONTACT AVEC LES FLAMMES

10" WATER COLUMN/D'UNE COLONNE D'EAU

MANIFOLD PRESSURE / PRESSION AU COLLECTEUR

4.5" WATER COLUMN/D'UNE COLONNE D'EAU

MANUFACTURER WITH THE APPLIANCE.

MINIMUM CLEARANCE TO

AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT.

11" WATER COLUMN/D'UNE COLONNE D 'EAU

MINIMUM SUPPLY PRESSURE / PRESSION D'ALIMENTATION MINIMALE

COMBUSTIBLE MATERIALS:

TOP 0”

DÉGAGEMENTS MINIMAUX DES MATÉRIAUX COMBUSTIBLES:

DESSUS 0” PROFONDEUR D'ENCASTRÉ 25"

13" WATER COLUMN/ D'UNE COLONNE D'EAU

L'APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT L'ENSEMBLE

MAXIMUM SUPPLY PRESSURE / PRESSION D'ALIMENTATION MAXIMALE

7.0" WATER COLUMN/D'UNE COLONNE D'EAU THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE

FLOOR 0” RECESSED DEPTH ONE SIDED 23"

RECESSED DEPTH SEE THRU 13.5” FRAMING (NOT INCLUDING

DIRECT VENT, VENTED GAS FIREPLACES. APPROVED FOR BEDROOM, BA THROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A. THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH LOCAL CODES, IF ANY; IF NONE, FOLLOW THE CURRENT ANSI Z223.1, OR CSA B149, INSTALLATION CODES. FOR USE WITH BARRIER W565-0198.

FOLLOW THE INSTALLATION INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL.

MANIFOLD PRESSURE: 3.5 INCHES W.C. (NG)

W385-2007

PLANCHER 0” ÉVENT 2"

CÔTES 0” MANTEAU 15" *

ARRIÉRE 0”

CLASSIFICATION: 115V 0.82AMP, 60HZ

D'ÉVACUATION PROPRE A NAPOLEON. RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTAIRE POUR L'ÉVACUATION

PRÉCISE. IL EST IMPORTANT DE BIEN RÉINSTALLER ET

RESCELLER L'ÉVENT APRÈS AVOIR ASSURÉ LE MAINTIEN DU SYSTÉME DE PRISE D'AIR.

DESSUS, COTÉS & ARRIÈRE: SELON LES ESPACEURS DE DÉGAGEMENT POUR LES MATÉRIAUX D'OSSATURE SELON LE MANUEL DE PROPRIÉTAIRE POUR LES MATÉRIAUX DE FINITION.

* L'EXTENSION HORIZONTALE MAXIMALE: 2". RÉFÉRER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS

PLUS GRANDES. RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTAIRE.

LV50

INTAKE SYSTEM.

SERIAL NUMBER/NO. DE SÉRIE:

FOR VENTING SPECIFICS. PROPER REINSTALLATION AND NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL

RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR

FACE MATERIAL)

ELECTRICAL RATING: 115V 0.82AMP, 60HZ

SIDES 0”

MADE IN CANADA / FABRIQUÉ AU CANADA

VENT 2" BACK 0”

MANTLE 15" * TOP, SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING MATERIALS. FOR FINISHING MATERIALS

SEE OWNERS MANUAL

* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION HORIZONTALE MAXIMALE: 2". SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS.

WOLF STEEL LTD. BARRIE, ONTARIO, CANADA

SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.

PRESSION AU COLLECTEUR: 3.5" D'UNE

PRESSION D'ALIMENTATION MIN: 4.5" D'UNE

PRESSION D'ALIMENTATION MAX: 7" D'UNE

NOT FOR USE WITH SOLID FUEL. FOR USE WITH GLASS DOORS CERTIFIED WITH THIS UNIT ONLY.

WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN CONTACT WITH THE FLAMES,

OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE. MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS / DÉGAGEMENTS MINIMAUX DES MATÉRIAUX COMBUSTIBLES: TOP/ DESSUS 0" RECESSED DEPTH ONE SIDED/ PROFONDEUR D'ENCASTRE UNE FACE 22.5" FLOOR / PLANCHER 0" RECESSED DEPTH SEE THRU/ PROFONDEUR D'ENCASTRE TRAVERS 17.25" FRAMING (NOT INCLUDING FACE MATERIAL) / OSSATURE (MATÉRIAU DE FAÇON NON COMPRIS) SIDES / CÔTÉS 0" BACK / ARRIÈRE 0" VENT TOP / DESSUS DU CONDUIT D’ÉVENT 3" VENT SIDES & BOTTOM / CÔTÉS ET DESSOUS DU CONDUIT D'ÉVENT 2" VERTICAL VENT / CONDUIT D’ÉVENT VERTICAL 1" MANTLE / TABLETTE 18" * TOP, SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING MATERIALS. FOR FINISHING MATERIALS SEE OWNERS MANUAL DESSUS, COTÉS & ARRIÈRE: SELON LES ESPACEURS DE DÉGAGEMENT POUR LES MATÉRIAUX D'OSSATURE SELON LA MANUEL DE PROPRIÉTAIRE POUR LESMATÉRIAUX DE FINITION.

CONFORMS TO / CONFORME AUX: ANSI Z21.50-2014, CERTIFIED TO / CERTIFIE CSA 2.22-2014 VENTED GAS FIREPLACE / FOYER À GAZ VENTILÉ.

3.5" D'UNE

9700539 (WSL) 4001657 (NGZ)

COLONNE D'EAU(GN)

NNE D'EAU(GN

4001658 (NAC) 4001659 (WUSA)

MIN SUPPLY PRESSURE: 4.5" W.C.(NG)

LV50N CLV50N MODEL CLV50P LV50P

40,000 BTU/h INPUT / ALIMENTATION 40,000 BTU/h

MAX. SUPPLY PRESSURE: 7" W.C. (NG)

COLONNE D'EAU (GN)

7" W.C. (NG

7" D'UNE

NNE D'EAU (GN

COLONNE D'EAU (GN)

* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION HORIZONTALE MAXIMALE: 2". SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS. RÉFÉRER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS PLUS GRANDES. SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS. REFERER AU MANUEL D'INSTALLATION DE PROPRIETAIRE POUR LES LONGUEURS D'EVACUATION MINIMALE ET MAXIMALE.

WOLF STEEL LTD.

0-4500FT (0-1370m) ALTITUDE / ÉLÉVATION 0-4500FT (0-1370m)

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

REDUCED INPUT / ALIMENTATION RÉDUITE

26,000 BTU/h

FOYER À GAZ VENTILÉ. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIÉ POUR INSTALLATION DANS UNE MAISON MOBILE SI

SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉES AU GAZ, EN VIGUEUR AU CANADA OU AUX ÉTATS-UNIS DE LA NORME DE SECURITÉ ET DE CONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ÉTATS-UNIS NE PEUT ÊTRE APPLIQUÉE, SE RÉFÉRER A LA NORME RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES SITES ET LES COMMUNAUTÉS, ANSI/NFPA 501A. CODES. INSTALLER L’APPAREIL SELON LES CODES OU RÈGLEMENTS LOCAUX, OU EN L’ABSENCE DE TELS RÈGLEMENTS, SELON LES CODES D’INSTALLATION ANSI Z223.1 OU CSA-B149 EN VIGUER.

W565-0198

. SUIVEZ LES INSTRUCTIONS D'INSTALLATION SE TROUVENT DANS LE

BARRIÈRE

32,000 BTU/h

UN COMBUSTIBLE SOLIDE NE DOIT PAS ÊTRE UTILISÉ AVEC CET APPAREIL. UTILISER AVEC LES PORTES VITRÉES HOMOLOGUÉES SEULEMENT AVEC CETTE UNITÉ.

AVERTISSEMENT: N’AJOUTEZ PAS A CET APPAREIL AUCUN MATÉRIAU DEVANT ENTRER EN CONTACT

AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT.

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR INTAKE SYSTEM. / L'APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT L'ENSEMBLE D'ÉVACUATION PROPRE A NAPOLEON. RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTAIRE POUR L'ÉVACUATION PRÉCISE. IL EST IMPORTANT DE BIEN RÉINSTALLER ET RESCELLER L'ÉVENT APRES AVOIR ASSURÉ LE MAINTIEN DU SYSTÉME DE PRISE D'AIR.

ELECTRICAL RATING: 115V, 60HZ. LESS THAN 12 AMPERES SPÉCIFICATIONS ÉLECTRIQUES: 115V, 60HZ. MOINS DE 12 AMPÈRE

DECORATIVE PRODUCT: NOT FOR USE AS A HEATING APPLIANCE PRODUIT DÉCORATIF: NE PAS UTILISER COMME APPAREIL DE CHAUFFAGE

49%49%

SERIAL NUMBER/NO. DE SÉRIE: LV50

POUR UNE UTILISER AVEC

MANUEL D'INSTALLATION.

MANIFOLD PRESSURE: 10 INCHES W.C.(LP) PRESSION AU COLLECTEUR: 10" D'UNE

COLONNE D'EAU (P)

MIN SUPPLY PRESSURE: 11" W.C. (LP) PRESSION D'ALIMENTATION MIN: 11" D'UNE

COLONNE D'EAU (P)

MAX. SUPPLY PRESSURE: 13" W.C. (LP) PRESSION D'ALIMENTATION MAX: 13" D'UNE

COLONNE D'EAU (P)

W385-2007

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to the model, venting and gas type of the appliance.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

W415-1439 / A / 07.10.15

3.0 VENTING

WARNING

RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.

IF VENTING IS INCLUDED WITH SPACERS THE VENT SYSTEM MUST BE SUPPORTED EVERY 3FT

(0.9m) FOR BOTH VERTICAL AND HORIZONTAL RUNS. USE SUPPORTS OR EQUIVALENT

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE REQUIRED CLEARANCE FROM

COMBUSTIBLES. USE WOLF STEEL LTD. SUPPORT RING ASSEMBLY W010-0067 OR EQUIVALENT

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE MINIMUM CLEARANCE TO COMBUSTIBLES

FOR BOTH VERTICAL AND HORIZONTAL RUNS. SPACERS ARE ATTACHED TO THE INNER PIPE AT

PREDETERMINED INTERVALS TO MAINTAIN AN EVEN AIR GAP TO THE OUTER PIPE. THIS GAP IS REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED AT THE START, MIDDLE AND END OF

EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS MUST NOT BE REMOVED.

THIS APPLIANCE USES A 5” (127mm) EXHAUST / 8” (203.2mm) AIR INTAKE VENT PIPE SYSTEM.

Refer to the section applicable to your installation.

For safe and proper operation of the appliance follow the venting instruction exactly. Deviation from the minimum vertical vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes (5-15) for the ﬂ ame to stabilize after ignition. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

NOTE: If for any reason the vent air intake system is disassembled; reinstall per the instructions provided for the initial installation.

NOTE: This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate constructions such as a chimney as part of the vent system is not permitted.

7.2C

3.1 VENTING LENGTHS AND COMPONENTS FOR DIRECT VENT INSTALLATIONS

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components. Minimum and maximum vent lengths, for both horizontal and vertical installations, and air terminal locations for either system are set out in this manual and must be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the installation procedure provided with the venting components.

A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

PART 5”/8” SUPPLIER WEBSITE

Duravent W175-0170 Wolf Steel www.duravent.com

Amerivent 5DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 5DT-AA Selkirk www.selkirkcorp.com

SuperSeal 5DDA Metal-Fab www.mtlfab.com

For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the installation procedure found on the website for your venting supplier.

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed using the black high temperature sealant Mill Pac.

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following

W415-1439 / A / 07.10.15

kit GD411, ﬂ at roof terminal kit GD412 or periscope kit GD401 (for wall penetration below grade). With ﬂ exible venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD420 or the 10 foot (3.1m) vent kit

GD430. For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a

minimum. The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed and undamaged. Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20 feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

Horizontal runs may have a 0” (0mm) rise per foot/meter however for optimum performance it is recommended that all horizontal runs have a minimum 1/4” (6.4mm) rise per foot/meter using ﬂ exible venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings. Local codes or regulations may require different clearances. Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air gap all around between the inner liner and outer liner is required for safe operation.

8.3_1A

3.2 TYPICAL VENT INSTALLATIONS

40" (1016MM)

MAXIMUM

32 1/4" (819MM)

MINIMUM

16" (406MM)

MINIMUM

40 FT (12M)

MAXIMUM

3 FT (1M)

MINIMUM

33"

(838MM)

* See “VENTING” section.

W415-1439 / A / 07.10.15

65 1/4" (1657MM) MINIMUM

PLUS RISE*

33"

(838MM)

3.3 SPECIAL VENT INSTALLATION

3.3.1 PERISCOPE TERMINATION

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when ﬁ nal grading is completed, the bottom air slot is located a minimum 12” (305m) above grade. The maximum allowable vent length is 10’ (3m) for a ﬁ replace and 8’ (2m) for a stove.

12"

(305MM)

MIN TO GRADE

32 1/4" (819MM)

MINIMUM

33"

(838MM)

9.1B

W415-1439 / A / 07.10.15

3.4 MINIMUM AIR TERMINAL LOCATION CLEARANCES

COVERED BALCONY APPLICATIONS ††*

= 3 feet

MIN

(0.9m)

= 2 x

MAX

ACTUAL

INSTALLATIONS

CANADA U.S.A.

A 12” (305mm) 12” (305mm) Clearance above grade, veranda porch, deck or balcony.

B 12” (305mm)

9”

(229mm)

Clearance to windows or doors that open.

C 12” (305mm)* 12” (305mm) * Clearance to permanently closed windows.

18”

(457mm)**

18” (457mm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m) from the center line of the terminal.

E 12” (305mm)** 12” (305mm)** Clearance to unventilated sofﬁ t. F 0” (0mm) 0” (0mm) Clearance to an outside corner wall.

0” (0mm)***

2” (51mm)***

0”

(0mm)***

2”

(51mm)***

H 3’(0.9m) 3’ (0.9m)****

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum vertical distance of 15’ (4.6m).

I 3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J 12” (305mm) 9” (229mm)

Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

K 6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet. L 7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

12”

(305mm)††

12”

(305mm)****

Clearance under a veranda, porch or deck.

N 16” (406mm) 16” (406mm) Clearance above the roof. O 2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings. P 8’ (2.4m) 8’(2.4m) Roof must be non-combustible without openings. Q 3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R 6’ (1.8m) 6’ (1.8m)

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening between the terminal and the open side of the structure.

S 12” (305mm) 12” (305mm) Clearance under a covered balcony

The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

NOTE: Clearances are in accordance with local installation codes and the requirements of the gas supplier.

12.1D

MAX

IHHW

(4.6m)

W415-1439 / A / 07.10.15

3.5 VENT APPLICATION FLOW CHART

Horizontal Termination

Vertical rise is equal

to or greater than the horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

3.6 DEFINITIONS

For the following symbols used in the venting calculations and examples are: > - greater than > - equal to or greater than < - less than < - equal to or less than HT - total of both horizontal vent lengths (Hr) and offsets (Ho) in feet HR - combined horizontal vent lengths in feet HO - offset factor: .03 (total degrees of offset - 90°*) in feet VT - combined vertical vent lengths in feet

TOP EXIT

Vertical rise is less than horizontal run

Horizontal run +

vertical rise to

maximum of 24.75

feet (7.5m)

4.2 times the

vertical rise equal to

or greater than the

horizontal run

Vertical Termination

Vertical rise is equal

to or greater than

the horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

Vertical rise is less than horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

3 times the vertical

rise equal to or

greater than the

horizontal run

13.3A

14.1

3.7 ELBOW VENT LENGTH VALUES

FEET INCHES MILLIMETERS 1° 0.03 0.5 12.7 15° 0.45 6.0 152.4 30° 0.9 11.0 279.4 45° 1.35 16.0 406.4 90°* 2.7 32.0 812.8

* The ﬁ rst 90° offset has a zero value and is shown in the formula as - 90°

15.1A

W415-1439 / A / 07.10.15

3.8 HORIZONTAL TERMINATION

(HT) < (VT)

Simple venting conﬁ guration (only one 90° elbow)

See graph to determine the required vertical

rise VT for the required horizontal run HT.

40 (12.2)

39 (11.9)

REQUIRED

30 (9.1)

VERTICAL

RISE IN FEET

20 (6.1)

(METERS)VT

10 (3.1)

2.5

(0.8)5(1.5)

7.5

(2.3)

(3.1)

12.5 (3.8)15(4.6)

HORIZONTAL VENT RUN PLUS OFFSET IN

FEET (METERS) H

The shaded area within the lines represents

acceptable values for HT and V

For vent conﬁ gurations requiring more than one 90° elbow, the following formulas apply: Formula 1: HT < V

Formula 2: HT + VT < 40 feet (12.2m)

17.5 (5.3)20(6.1)

Example: V1 = 3 FT (0.9m)

V2 = 8 FT (2.4m) VT = V1 + V2= 3 FT (0.9m ) + 8 FT (2.4m) = 11 FT (3.4m) H1 = 2.5 FT (0.8m) H2 = 2 FT (0.6m) HR = H1 + H2 = 2.5 FT (0.8m) + 2 FT (0.6m) = 4.5 FT (1.4m) HO = .03 (three 90° elbows - 90°) = .03 (270° - 90°) = 5.4 FT (1.7m) HT = HR + HO = 4.5 FT (1.4m) + 5.4 FT (1.6m) = 9.9 FT (3m) HT + VT = 9.9 FT (3m) + 11 FT (3.4m) = 20.9 FT (6.4m)

Formula 1: HT < V

9.9 FT (3m) < 11 FT (3.4m) Formula 2: HT + VT < 40 FT (12.2m)

20.9 FT (6.4m) < 40 FT (12.2m) Since both formulas are met, this vent conﬁ guration is acceptable.

90°

16.1B

90°

W415-1439 / A / 07.10.15

V V V

(HT) > (VT)

Simple venting configuration (only one 90° elbow)

See graph to determine the required vertical rise VT for the

150 (3810)

147 (3733.8)

required horizontal run H

REQUIRED

VERTICAL RISE

100 (2540)

IN INCHES

(MILLIMETERS)V

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS)H

57 (1447.8)

15 (381)

50 (1270)

(1.5)

(0.6)

(3.1)

12.5

(3.8)

(4.6)

20 (6.1)

19.5 (5.9)

The shaded area within the lines represents acceptable

values for H

and VT

For vent configurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: Formula 2: HT + V

< 4.2 V

< 24.75 feet (7.5m)

90°

Example:

= VT = 6 FT (1.8m)

= 3 FT (0.9m)

= 5 FT (1.5m)

= H

+ H

= .03 (two 90° elbows - 90°)=.03 (180° - 90°) = 2.7FT (0.8m)

= H

+ V

= 3FT (0.9m) + 5FT (1.5m) = 8FT (2.4m)

+ HO = 8FT (2.4m) + 2.7FT (0.8m) = 10.7FT (3.3m)

= 10.7FT (3.3m) + 6FT (1.8m) = 16.7FT (5.1m)

90°

Formula 1: HT < 4.2 V

4.2 VT = 4.2FT (1.3m) x 6FT (1.8m) = 25.2FT (7.7m)

10.7FT (3.3m) < 25.2FT (7.7m)

Formula 2: HT + V

16.7FT (5.1m) < 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

Example:

= 4 FT (1.2m)

= 1.5 FT (0.5m)

= V

+ V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= H

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

+ H2 + H

+ H

= 13.6FT (4.2m) + 5.5FT (1.7m) = 19.1 FT (5.8m)

+ H4 = 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (0.5m) = 5.5FT (1.7m)

= 5.5FT (1.7m) + 8.1FT (2.5m) = 13.6FT (4.2m)

Formula 1: HT < 4.2 V

4.2 VT = 4.2FT (1.3m) x 5.5FT (1.7m) = 23.1FT (7m)

< 24.75 FT (7.5m)

90°

13.6FT (4.2m) < 23.1FT (7m) Formula 2: HT + V

19.1FT (5.8m) < 24.75 FT (7.5m)

< 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

16.4A

W415-1439 / A / 07.10.15

3.9 VERTICAL TERMINATION

(HT) < (VT)

Simple venting configurations.

See graph to determine the required vertical rise V

required horizontal run HT.

40 (12.2)

30 (9.1)

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

3 (0.9)

20 (6.1)

10 (3.1)

(1.5)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

The shaded area within the lines represents acceptable

values for HT and VT

For vent configurations requiring one or more 90° elbows the following formulas apply: Formula 1: H

Formula 2: HT + V

< V

< 40 feet (12.2m)

(3.1)

(4.6)

(6.1)

for the

Example: V

= 5 FT (1.5m)

= 6 FT (1.8m)

= 10 FT (3.1m)

= V

+ V2 + V3 = 5FT (1.5m) + 6FT (1.8m) + 10FT (3.1m) = 21FT (6.4m)

= 8 FT (2.4m)

= 2.5 FT (0.8m)

= H

+ H

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

Formula 1: HT < V

18.6FT (5.7m) < 21FT (6.4m) Formula 2: HT + V

39.6FT (12.1m) < 40FT (12.2m)

= 8FT (2.4m) + 2.5FT (0.8m) = 10.5 FT (3.2m)

+ H

= 10.5FT (3.2m) + 8.1FT (2.5m) = 18.6FT (5.7m)

= 18.6FT (5.7m) + 21FT (6.4m) = 39.6FT (12.1m)

< 40 FT (12.19m)

Since both formulas are met, this vent configuration is acceptable.

90°

18.1A

W415-1439 / A / 07.10.15

Simple venting configurations.

(HT) > (VT)

20 (6.1)

19 (5.8)

See graph to determine the required vertical rise V

required horizontal run H

for the

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

3 (0.9)

10 (3.1)

(1.5)

(3.1)

(4.6)

(6.1)

(7.6)

(9.1)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

The shaded area within the lines represents acceptable

values for H

and VT

For vent configurations requiring more than two 90° elbows the following formulas apply: Formula 1: H

Formula 2: HT + V

< 3V

< 40 feet (12.2m)

Example: V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= V1+V2+V3= 2FT (0.6m) + 1FT (0.3m) + 1.5FT (0.5m) = 4.5FT (1.4m)

= 6 FT (1.8m)

= 2 FT (0.6m)

= H

+ H

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

= 6FT (1.8m) + 2FT (0.6m) = 8 FT (2.4m)

+ H

= 8FT (2.4m) + 8.1FT (2.5m) = 16.1FT (4.9m)

= 16.1FT (4.9m) + 4.5FT (1.4m) = 20.6 FT (6.3m)

90°

Formula 1: HT < 3V 3VT = 3FT (0.9m) x 4.5FT (1.4m) = 13.5FT (4.1m)

16.1FT (4.9m) > 13.5FT (4.1m) Since this formula is not met, this vent configuration is unacceptable. Formula 2: HT + VT < 40 feet (12.2m)

20.6FT (6.3m) < 40 (12.2m)

Since only formula 2 is met, this vent configuration is unacceptable and a new appliance location or vent configuration will need to be established to satisfy both formulas.

18.1_2B

W415-1439 / A / 07.10.15

4.0 INSTALLATION

ENSURE TO UNPACK ALL LOOSE MATERIALS FROM INSIDE THE FIREBOX PRIOR TO HOOKING UP

IF YOUR APPLIANCE IS SUPPLIED WITH A REMOTE ENSURE THE REMOTE RECEIVER IS IN THE

“OFF” POSITION PRIOR TO HOOKING UP THE GAS AND ELECTRICAL SUPPLY TO THE APPLIANCE.

FOR SAFE AND PROPER OPERATION OF THE APPLIANCE, FOLLOW THE VENTING INSTRUCTIONS

ALL INNER EXHAUST AND OUTER INTAKE VENT PIPE JOINTS MAY BE SEALED USING EITHER RED

RTV HIGH TEMP SILICONE SEALANT W573-0002 (NOT SUPPLIED) OR BLACK HIGH TEMP MILL PAC

W573-0007 (NOT SUPPLIED) WITH THE EXCEPTION OF THE APPLIANCE EXHAUST FLUE COLLAR

IF USING PIPE CLAMPS TO CONNECT VENT COMPONENTS, 3 SCREWS MUST ALSO BE USED TO

RISK OF FIRE, EXPLOSION OR ASPHYXIATION. IMPROPER SUPPORT OF THE ENTIRE VENTING

SYSTEM MAY ALLOW VENT TO SAG AND SEPARATE. USE VENT RUN SUPPORTS AND CONNECT

WARNING

THE GAS AND ELECTRICAL SUPPLY.

EXACTLY.

WHICH MUST BE SEALED USING MILL PAC.

ENSURE THE CONNECTION CANNOT SLIP OFF.

DO NOT CLAMP THE FLEXIBLE VENT PIPE.

VENT SECTIONS PER INSTALLATION INSTRUCTIONS.

RISK OF FIRE, DO NOT ALLOW LOOSE MATERIALS OR INSULATION TO TOUCH THE VENT PIPE.

REMOVE INSULATION TO ALLOW FOR THE INSTALLATION OF THE ATTIC SHIELD AND TO

MAINTAIN CLEARANCES TO COMBUSTIBLES.

68.2B

4.1 WALL AND CEILING PROTECTION

WARNING

DO NOT FILL THE SPACE BETWEEN THE VENT PIPE AND ENCLOSURE WITH ANY TYPE OF

MATERIAL. DO NOT PACK INSULATION OR COMBUSTIBLES BETWEEN CEILING FIRESTOPS.

ALWAYS MAINTAIN SPECIFIED CLEARANCES AROUND VENTING AND FIRESTOP SYSTEMS.

INSTALL WALL SHIELDS AND FIRESTOPS AS SPECIFIED. FAILURE TO KEEP INSULATION OR

OTHER MATERIALS AWAY FROM VENT PIPE MAY CAUSE FIRE.

70.1

For optimum performance it is recommended that all horizontal runs have a minimum of 1/4" (6mm) rise per foot using ﬂ exible venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

W415-1439 / A / 07.10.15

4.1.1 HORIZONTAL INSTALLATION

WARNING

THE FIRESTOP ASSEMBLY MUST BE INSTALLED WITH THE VENT SHIELD TO THE TOP.

TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE

RETURN FLANGE OF THE MOUNTING PLATE.

This application occurs when venting through an exterior wall. Having determined the correct height for the air terminal location, cut and frame a hole in the exterior wall as illustrated to accommodate the ﬁ restop assembly. Dry ﬁ t the ﬁ restop assembly before proceeding to ensure the brackets on the rear surface ﬁ t to the inside surface of the horizontal framing.

The length of the vent shield may be cut shorter for combustible walls that are less than 8 1/2” (215.9mm) thick but the vent shield must extend the full depth of the combustible wall.

A. Apply a bead of caulking (not supplied) around the corner edge of the inside surface of the ﬁ restop assembly, ﬁ t the ﬁ restop assembly to the hole and secure using the 4 screws (supplied in your manual baggie).

B. Once the vent pipe is installed in its ﬁ nal position, apply high temperature sealant W573-0007 (not supplied) between the pipe and the ﬁ restop.

CAULKING

FIRESTOP

SPACER

VENT

SHIELD

DETERMINE THE CORRECT HEIGHT

FINISHING MATERIAL

20.2A

4.1.2 VERTICAL INSTALLATION

This application occurs when venting through a roof. Installation kits for various roof pitches are available from your authorized dealer / distributor. See accessories to order speciﬁ c kits required.

A. Determine the air terminal location, cut and frame a square opening as

illustrated in the ceiling and the roof to provide the minimum 1" (25mm) clearance between the vent pipe and any combustible material. Try to center the vent pipe location midway between two joists to prevent having to cut them. Use a plumb bob to line up the center of the openings. A vent pipe shield will prevent any materials such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe. Nail headers between the joist for extra support.

B. Apply a bead of caulking (not supplied) to the framework or to the Wolf Steel

vent pipe shield plate or equivalent (in the case of a ﬁ nished ceiling), and secure over the opening in the ceiling. A ﬁ restop must be placed on the bottom of each framed opening in a roof or ceiling that the venting system passes through. Apply a bead of caulking all around and place a ﬁ restop spacer over the vent shield to restrict cold air from being drawn into the room or around the ﬁ replace. Ensure that both spacer and shield maintain the required clearance to combustibles. Once the vent pipe is installed in its ﬁ nal position, apply sealant between the pipe and the ﬁ restop assembly.

C. In the attic, slide the vent pipe collar down to cover up the open end of the shield and

tighten. This will prevent any materials, such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

10 3/4"

(273mm)

FIRESTOP

UNDERSIDE OF

JOIST

VENT PIPE

SHIELD

21.1A

W415-1439 / A / 07.10.15

10 3/4"

(273mm)

CAULKING

VENT

PIPE

COLLAR

VENT

PIPE

4.2 USING FLEXIBLE VENT COMPONENTS

DO NOT ALLOW THE INNER FLEX PIPE TO BUNCH UP ON HORIZONTAL OR VERTICAL RUNS AND ELBOWS.

KEEP IT PULLED TIGHT.

SPACERS ARE ATTACHED TO THE INNER FLEX PIPE AT PREDETERMINED INTERVALS TO MAINTAIN AN EVEN AIR GAP TO THE OUTER FLEX PIPE. THIS GAP IS REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED

AT THE START, MIDDLE AND END OF EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS

MUST NOT BE REMOVED.

For safe and proper operation of the appliance, follow the venting instructions exactly. All inner ﬂ ex pipe and outer ﬂ ex pipe joints may be sealed using high

ELBOW

SPACERS

temperature sealant W573-0002 (not supplied) or the high temperature sealant W573-0007 Mill Pac (not supplied). However, the high temperature sealant W573-0007 Mill Pac (not supplied) must be used on the joint connecting the inner ﬂ ex pipe and the exhaust ﬂ ue collar.

Use only approved ﬂ exible vent pipe kits marked:

WARNING

“Wolf Steel Approved Venting” as identiﬁ ed by the stamp only on the outer ﬂ ex pipe.

4.2.1 HORIZONTAL AIR TERMINAL INSTALLATION

A. Stretch the inner ﬂ ex pipe to the required

length needed for the ﬁ nished wall surface. Apply a heavy bead of high temperature sealant W573-0007 Mill Pac (not supplied) to the inner sleeve of the air terminal. Slip the vent pipe a minimum of 2” (50.8mm) over the inner sleeve of the air terminal and secure with 3 #8 screws.

B. Using the outer ﬂ ex pipe, slide over the outer

combustion air sleeve of the air terminal and secure with 3 #8 screws. Seal using high temperature sealant W573-0002 (not supplied).

C. Insert the vent pipes through the ﬁ restop

maintaining the required clearance to combustibles. Holding the air terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing with caulking (not supplied).

#10x2"

SCREWS

HI-TEMP

SEALANT

22.1

OUTER FLEX

PIPE

CAULKING

INNER FLEX

PIPE

2" (50.8mm) OVERLAP

HI-TEMP

SEALANT

#8 X 1/2” SELF DRILLING

SCREWS

INNER COUPLER

OUTER COUPLER

D. If more vent pipe needs to be used to

reach the ﬁ replace, couple them together as illustrated. The vent system must be supported approximately every 3 feet (0.9mm) for both vertical and horizontal runs. Use noncombustible strapping to maintain the minimum 1” (25.4mm) clearance to combustibles.

The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the depth of its return ﬂ ange.

W415-1439 / A / 07.10.15

OUTER

FLEX PIPE

OUTER

FLEX PIPE INNER FLEX PIPE

23.3B

4.2.2 VERTICAL AIR TERMINAL INSTALLATION

WARNING

MAINTAIN A MINIMUM 2” (51mm) SPACE BETWEEN THE AIR INLET BASE AND THE STORM COLLAR.

A. Fasten the roof support to the roof using the screws provided. The

roof support is optional. In this case the venting is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the optional roof support.

B. Stretch the inner ﬂ ex pipe to the required length. Slip the

inner ﬂ ex pipe a minimum of 2” (51mm) over the inner pipe of the air terminal connector and secure with 3 #8 screws. Seal using a heavy bead of high temperature sealant W573-0007 (not supplied).

C. Repeat using the outer ﬂ ex pipe, using a heavy bead of

high temperature sealant W573-0002 (not supplied).

D. Thread the air terminal connector / vent pipe assembly down through

the roof. The air terminal must be positioned vertically and plumb. Attach the air terminal connector to the roof support, ensuring that the top of the air terminal is 16” (406mm) above the highest point that it penetrates the roof.

E. Remove nails from the shingles, above and to the sides of the air

terminal connector. Place the ﬂ ashing over the air terminal connector leaving a min. 3/4” (19mm) of the air terminal connector showing above the top of the ﬂ ashing. Slide the ﬂ ashing underneath the sides and upper edge of the shingles. Ensure that the air terminal connector is properly centred within the ﬂ ashing, giving a 3/4” (19mm) margin all around. Fasten to the roof. Do not nail through the lower portion of the ﬂ ashing. Make weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the ﬂ ashing with rooﬁ ng material.

F. Aligning the seams of the terminal and air terminal connector,

place the terminal over the air terminal connector making sure the vent pipe goes into the hole in the terminal. Secure with the three screws provided.

G. Apply a heavy bead of weatherproof caulking 2” (51mm) above

the ﬂ ashing. Install the storm collar around the air terminal and slide down to the caulking. Tighten to ensure that a weathertight seal between the air terminal and the collar is achieved.

ROOF SUPPORT

AIR

TERMINAL

CONNECTOR

2” (51mm)

INNER PIPE

HIGH TEMPERATURE SEALANT

INNER FLEX PIPE

OUTER FLEX PIPE

AIR I NL ET BASE

CAULKING

STORM COLLAR

WEA THER SEALANT

FLASHING

H. If more vent pipe needs to be used to reach the appliance see “HORIZONTAL

AIR TERMINAL INSTALLATION” section.

24.1A

W415-1439 / A / 07.10.15

4.2.3 APPLIANCE VENT CONNECTION

A. Install the inner exhaust ﬂ ue collar to the appliance. Secure

B. Install the outer ﬂ ex pipe to the appliance. Attach and seal the

with 3 screws. Seal the joint and screw holes using the high temperature sealant Mill-Pac W573-0007 (not supplied).

joints using a high temperature sealant.

4.3 MOBILE HOME INSTALLATION

This appliance is also certiﬁ ed to be installed as an OEM (Original Equipment Manufacturer) installation in a manufactured home (U.S. only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plate.

This Mobile/Manufactured Home Listed appliance comes factory equipped with a means to secure the unit. Built in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base. Use #10 hex head screws, inserted through the holes in the base to secure. For free standing products contact your local authorized dealer / distributor for the appropriate securing kit. For mobile home installations, the appliance must be fastened in place. It is recommended that the appliance be secured in all installations. Always turn off the pilot and the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the appliance, ensure that the logs are positioned correctly.

#8 X 1/2”

SELF

DRILLING

SCREWS

2” (50.8mm) OVERLAP

HIGH TEMP SEALANT

28.1C

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

conversion kit is supplied with the mobile home appliance.

Conversion Kits This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (LP). To convert from one gas to another consult your Authorized dealer/distributor.

29.1A

W415-1439 / A / 07.10.15

4.4 GAS INSTALLATION

RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS

SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT

WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE

PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT

THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND

ELECTRICAL LOCATIONS, SEE “DIMENSION” SECTION.

ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS

VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.

Installation and servicing to be done by a qualiﬁ ed installer. Do not use open ﬂ ame.

• Move the appliance into position and secure.

• If equipped with a ﬂ ex connector the appliance is designed to accept a 1/2” (13mm) gas supply. Without the connector it is designed to accept a 3/8” (9.5mm) gas supply. The appliance is equipped with a manual shut off valve to turn off the gas supply to the appliance.

• Connect the gas supply in accordance to local codes. In the absence of local codes, install to the current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States.

• When ﬂ exing any gas line, support the gas valve so that the lines are not bent or kinked.

• Check for gas leaks by brushing on a soap and water solution.

WARNING

SPARKS OR OPEN FLAMES.

LINE AT TEST PRESSURES ABOVE 1/2 PSIG.

30.1A

2" (51mm)

NOTE: Connect the gas supply to the 1/2" (13mm) shut off and ﬂ ex connector (supplied). Ensure gas supply is secured.

14" (356mm)

W415-1439 / A / 07.10.15

5.0 FRAMING

IN ORDER TO AVOID THE POSSIBILITY OF EXPOSED INSULATION OR VAPOUR BARRIER COMING

IN CONTACT WITH THE APPLIANCE BODY, IT IS RECOMMENDED THAT THE WALLS OF THE

APPLIANCE ENCLOSURE BE “FINISHED” (IE: DRYWALL / SHEETROCK), AS YOU WOULD FINISH

DO NOT NOTCH THE FRAMING AROUND THE APPLIANCE STAND-OFFS. FAILURE TO MAINTAIN

AIR SPACE CLEARANCE MAY CAUSE OVER HEATING AND FIRE. PREVENT CONTACT WITH

SAGGING OR LOOSE INSULATION OR FRAMING AND OTHER COMBUSTIBLE MATERIALS. BLOCK

OPENING INTO THE CHASE TO PREVENT ENTRY OF BLOWN-IN INSULATION. MAKE SURE

WHEN CONSTRUCTING THE ENCLOSURE ALLOW FOR FINISHING MATERIAL THICKNESS TO MAINTAIN CLEARANCES. FRAMING OR FINISHING MATERIAL CLOSER THAN THE MINIMUMS

LISTED MUST BE CONSTRUCTED ENTIRELY OF NON-COMBUSTIBLE MATERIALS. MATERIALS CONSISTING ENTIRELY OF STEEL, IRON, BRICK, TILE, CONCRETE, SLATE, GLASS OR PLASTERS, OR ANY COMBINATION THEREOF ARE SUITABLE. MATERIALS THAT ARE REPORTED AS PASSING

ASTM E 136, STANDARD TEST METHOD FOR BEHAVIOUR OF MATERIALS IN A VERTICAL TUBE

FURNACE AT 750°C/1382°F AND UL763 SHALL BE CONSIDERED NON-COMBUSTIBLE MATERIALS.

MINIMUM CLEARANCE TO COMBUSTIBLES MUST BE MAINTAINED OR A SERIOUS FIRE HAZARD

THE APPLIANCE REQUIRES A MINIMUM ENCLOSURE HEIGHT. MEASURE FROM THE APPLIANCE

WARNING

RISK OF FIRE!

ANY OTHER OUTSIDE WALL OF A HOME. THIS WILL ENSURE THAT CLEARANCE TO

COMBUSTIBLES IS MAINTAINED WITHIN THE CAVITY.

INSULATION AND OTHER MATERIALS ARE SECURED.

COULD RESULT.

BASE.

IF STEEL STUD FRAMING KITS WITH CEMENT BOARD ARE PROVIDED, THEY MUST BE

INSTALLED.

71.1

The LV50 is installed into a rectangular opening. It is best to frame your appliance after it is positioned and the vent system is installed. Use the steel stud frame provided.

Maintain these minimum clearances to combustibles from appliance and vent surfaces: Appliance framing:

Use steel stud framing provided.

Non- Combustible Appliance ﬁ nishing:

Front - 7" (177.8mm) to sides of appliance opening

- 26 1/2" (673.1mm) above appliance opening

Combustible Appliance ﬁ nishing:

- 52" (1320.8mm) from bottom of appliance to enclosure top

- 3" (76mm) to top of vent pipe*

- 2" (51mm) to sides and bottom of vent pipe*

Non-combustible ﬁ nishing material (ie. cement board, brick, stone, tile) must be used to ﬁ nish the front of the appliance.

*HORIZONTAL VENT SECTIONS: A minimum clearance of 3" (76mm) to the top and 2" (51mm) to the sides and bottom of the vent pipe on all horizontal runs to combustibles is required when passing through a wall. Use ﬁ restop spacer W010-2107 (supplied). Horizontal vent sections within enclosures require a minimum clearance of 6" (152mm) at the top of the vent pipe, see “MINIMUM CLEARANCE TO COMBUSTIBLE ENCLOSURES” section and 1" (25mm) to the sides of the vent pipe.

*VERTICAL VENT SECTIONS: A minimum of 1" (25mm) all around the vent pipe on all vertical runs to combustibles is required when passing through a ceiling. Use ﬁ restop spacer W500-0028 (not supplied).

W415-1439 / A / 07.10.15

25 5/8"

574.7mm

25 5/8"

574.7mm

25.4mm

65 3/8"

1660.5mm

73"

1854.2mm

65 3/8"

1660.5mm

65 3/8"

1660.5mm

110"

2794mm

W415-1439 / A / 07.10.15

5.1 TWO SIDED APPLIANCE

WARNING

EDGES ARE SHARP, ALWAYS WEAR GLOVES WHEN WORKING WITH SHEET METAL.

A. The steel frame is pre-assembled but must be secured to the appliance in 3 places for both sides, as

shown.

B. The steel frame supplied must be installed as shown.

NOTE: For heavier ﬁ nishing materials such as marble, we recommend adding extra support to the frame. Screw the metal studs in place. Ensure there is adequate ﬂ oor support for the appliance and ﬁ nishing material.

METAL STUD

W415-1439 / A / 07.10.15

WARNING

METAL STUDS REQUIRED TO ENSURE CLEARANCE TO COMBUSTIBLES.

IMPORTANT: Before ﬁ nishing in the appliance test the operation using the remote control, cycling it through all of its different modes, see “OPERATION” section. Should trouble shooting be required, access to the controls can be made through the pre-ﬁ nishing access panel.

75 1/4"

1911mm

MINIMUM

50"

1270mm MINIMUM

METAL STUDS (NOT MANDATORY)

65 3/8"

1661mm

NOTE: Power vent system available with reduced vent pipe clearances. Contact your authorized dealer / distributor for more information.

16 1/4"

413mm

W415-1439 / A / 07.10.15

5.2 ONE SIDE APPLIANCE

WARNING

EDGES ARE SHARP, ALWAYS WEAR GLOVES WHEN WORKING WITH SHEET METAL.

A. The steel frame is pre-assembled but must be secured to the appliance in 3 places for both sides, as

shown.

B. The steel frame supplied must be installed as shown.

METAL STUD

W415-1439 / A / 07.10.15

* When constructing the enclosure allow for ﬁ nishing material thickness to maintain clearances.

75 1/4"

1911mm MINIMUM

50"

1270mm MINIMUM

65 3/8"

1661mm

STAND OFF

51mm

22 5/8"

574.7mm *

W415-1439 / A / 07.10.15

5.3 MINIMUM CLEARANCE TO COMBUSTIBLE ENCLOSURES

THE FRONT OF THE APPLIANCE MUST BE FINISHED WITH ANY NON-COMBUSTIBLE MATERIALS

SUCH AS BRICK, MARBLE, GRANITE, ETC., AS LONG AS THESE MATERIALS NEVER OVERHANG

INTO THE APPLIANCE OPENING.

IMPORTANT: The LV50 requires a minimum inside enclosure height of 75 1/4" (1911.4mm), measured

from the bottom of the appliance. For temperature requirements, this area must be left unobstructed. It is recommended that the enclosure be ventilated at the top and bottom to circulate the hot air.

Before ﬁ nishing in the appliance test the operation using the remote control, cycling it through all of its different

modes, see “OPERATION” section. Check pressure readings, see “PILOT BURNER ADJUSTMENT” section.

Once ﬁ nished in, access to the control components can only be done through the inside of the appliance.

NOTE: JOINT COMPOUNDS AND TAPES THAT ARE RESILIENT TO HEAT AND CRACKING SHOULD BE USED WHEN TAPING AND MUDDING SEAMS.

STEEL STUD

FRAME

HEAT SHIELD

WARNING

TOP OF ENCLOSURE

152mm *

COMBUSTIBLE

NON-COMBUSTIBLE

0” IF NON-COMBUSTIBLE FINISHING IS USED SUCH AS BRICK AND STONE.

76mm

75 1/4"

1911mm

MINIMUM

ENCLOSURE

HEIGHT

26 1/2"

673mm

MINIMUM

TOP OF

APPLIANCE

OPENING

651mm

MINIMUM

25 5/8"

NON-COMBUSTIBLE

COMBUSTIBLE

MATERIAL

178mm

TO SIDEWALL

51mm

65 1/4"

1657mm

MINIMUM

PLUS RISE**

* Within the appliance enclosure a 6" (152mm) clearance between the top of the vent pipe and combustible materials is required. All other clearances within the enclosure, including where the vent pipe exits the enclosure are subject to 2" (51mm) to the sides and bottom and 3" (76mm) to the top for horizontal and 1" (25mm) for vertical.

** See venting section.

W415-1439 / A / 07.10.15

+ 106 hidden pages

Napoleon LV50N, LV50N2, LV50P2, LV50P Installation And Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual