Napoleon Ascent X, GX36-1, GX42, GX70-1, GX36NTR-1 Owner's Manual

ENGLISH

FRENCH

PG. 25

OWNER’S MANUAL

Ascent X™ Series

(GX42 illustrated)

For indoor use only

SAFETY INFORMATION

!

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the supplier.

GX42 Only GX36-1 & GX70-1

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone [phone] • www.napoleonappliances.com • [e-mail]

W415-1853 / A / 08.17.18

EN

!

WARNING

safety information

• This appliance is hot when operated and can cause
severe burns if contacted.

• Any changes to this appliance or its control can be

dangerous and are prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure
to operate appliance according to operating
instructions could cause fi re or injury.

• Risk of fi re or asphyxiation do not operate appliance

with fi xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off

and cooled before servicing.

• Do not install damaged, incomplete or substitute

components.

• Risk of cuts and abrasions. Wear protective gloves
and safety glasses during installation. Sheet metal
edges may be sharp.

• Children and adults should be alerted to the

hazards of high surface temperature and should
stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised

when they are in the same room as the appliance.
Toddlers, young children, and others may be
susceptible to accidental contact burns. A
physical barrier is recommended if there are at
risk individuals in the house. To restrict access to
an appliance or stove, install an adjustable safety
gate to keep toddlers, young children and other at
risk individuals out of the room and away from hot
surfaces.

• Clothing or other fl ammable material should not be

placed on or near the appliance.

• Due to high temperatures, the appliance should be

located out of traffi c and away from furniture and
draperies.

• Ensure you have incorporated adequate safety
measure to protect infants/toddlers from touching
hot surfaces.

• Even after the appliance is out, the glass and/or

screen will remain hot for an extended period of
time.

• Check with your local hearth specialty dealer

for safety screens and hearth guards to protect
children from hot surfaces. These screens and
guards must be fastened to the fl oor.

• Any safety screen, guard or barrier removed for

servicing the appliance, must be replaced prior to
operating the appliance.

• The appliance is a vented gas-fi red appliance. Do

not burn wood or other materials in the appliance.

• The appliance area must be kept clear and free

from combustible materials, gasoline and other
fl ammable vapors and liquids.

• Under no circumstances should this appliance be
modifi ed.

• This appliance must not be connected to a chimney
fl ue pipe serving a separate solid fuel burning
appliance.

• Do not use this appliance if any part has been
under water. Immediately call a qualifi ed service
technician to inspect the appliance and to replace
any part of the control system and any gas control
which has been under water.

• Do not operate the appliance with the glass door
removed, cracked or broken. Replacement of the
glass should be done by a licensed or qualifi ed
service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they
must be kept closed while the appliance is
operating to prevent exhaust fumes containing
carbon monoxide, from entering into the home.
Temperatures of the exhaust escaping through
these openings can also cause the surrounding
combustible materials to overheat and catch fi re.

• Only doors / optional fronts certifi ed with the unit

are to be installed on the appliance.

• Keep the packaging material out of reach of
children and dispose of the material in a safe
manner. As with all plastic bags, these are not toys
and should be kept away from children and infants.

• As with any combustion appliance, we recommend
having your appliance regularly inspected and
serviced as well as having a carbon monoxide
detector installed in the same area to defend you
and your family against carbon monoxide.

• Ensure clearances to combustibles are maintained

when building a mantel or shelves above the
appliance. Elevated temperatures on the wall or
in the air above the appliance can cause melting,
discolouration or damage to decorations, a T.V. or
other electronic components.

• A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance
and shall be installed.

• If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this
appliance.

• Installation and repair should be done by a qualifi ed

service person. The appliance should be inspected
before use and at least annually by a professional
service person. More frequent cleaning may be
required due to excessive lint from carpeting,
bedding material, etc. It is imperative that control
compartments, burners and circulating air
passageways of the appliance be kept clean.

2

W415-1853 / A / 08.17.18

table of contents

!

WARNING:

Electric

This product can expose you to chemicals including lead and lead compounds,

Gas, Wood

which are known to the State of California to cause cancer, and chemicals including BBP and
DEHP, which are known to the State of California to cause birth defects or other reproductive
harm. For more information, go to www.P65Warnings.ca.gov.

!

AVERTISSEMENT:

Ce produit peut vous exposer à des substances chimiques incluant le

plomb et les composés de plomb qui, selon l’État de Californie, causeraient le cancer, et des
substances chimiques incluant le BBP et DEHP qui, selon d’État de Californie, causeraient des
malformations congénitales ou autres dangers pour la reproduction.
Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

!

ADVERTENICA:

Este producto puede exponerlo a productos químicos, entre ellos, plomo
y compuestos con plomo, que el Estado de California reconoce como causantes de cáncer, y
productos químicos, entre ellos, bencilbutilftalato (BBP, por sus siglas en inglés) y di(2-etilhex-
il) ftalato (DEHP, por sus siglas en inglés), que el Estado de California reconoce como caus-
antes de malformaciones congénitas u otros daños para la reproducción. Para obtener más
información, visite www.P65Warnings.ca.gov.

1.0 getting to know your appliance 5

1.1 control access 6

1.2 rating plate information 6

2.0 operating your appliance 7

2.1 using your appliance 7

2.2 on/off components 7

2.2.1 changing the batteries in the battery holder 8

2.2.2 turndown (GX36-1 & GX42 only) 9

3.0 clearances around appliance 10

4.0 maintenance 12

4.1 care of glass 13

4.2 care of plated parts 13

4.3 safety barrier removal 14

4.4 firebox glass door removal 14

5.0 replacement parts 15

6.0 GX36-1 accessories 16

7.0 GX42 accessories 18

8.0 GX70-1 accessories 19

9.0 troubleshooting 20

10.0 warranty 21

11.0 service history 22

EN

This owner’s manual is written for a complete series of appliances that have a variety of different features and
specifications. Before reading this manual, be sure you know which model of appliance that you have. This infor­mation will have been filled out by the installer on the following page and on the rating plate that is permanently
attached to the appliance (see “rating plate information” section).

This manual is for the:

• Ascent X Series (GX36-1, GX42 and GX70-1 models)

If required, more detailed technical information is included in the appliance installation manual.

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves
the right to change or modify any information within this manual at any time without notice.

Visit the Napoleon website for the most current version of your appliance’s manual.

Changes, other than editorial, are denoted by a vertical line in the margin.

!

which are known to the State of California to cause cancer, and chemicals including carbon
monoxide, which are known to the State of California to cause birth defects or other reproduc­tive harm. For more information, go to www.P65Warnings.ca.gov.

WARNING:

This product can expose you to chemicals including lead and lead compounds,

W415-1853 / A / 08.17.18

3

EN

welcome

congratulations!

Napoleon is proudly committed to your total home comfort. We are proud to say that our products continunously
surpass industry standards and our inspiration is you! More than anything, we want you to feel confident in
choosing Napoleon for your home. Our products are designed to provide that confidence and ensure that every
Napoleon product is beyond compare.

Napoleon products are designed with superior components and materials assembled by trained craftsmen who
take great pride in their work.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance for your
safety. This barrier must be installed.

Your Napoleon appliance has been thoroughly inspected by a qualified technician before packaging to ensure that
you, the customer, receives the quality product that you expect from Napoloen.

Dealer : Fill in your dealer information (or business card) and the appliance installation information
below.

Dealer Information

Name of Dealer:
Dealer Location:
Dealer Phone:
Dealer E-mail:

Customer:
Customer Address:
Date of Installation:
Location of the appliance:
Installer:

Dealer: Business card location

Serial Number:

Model:

Natural Gas: GX36NTR-1

GX36NTRE-1
GX42NTRE
GX70NTE-1

4

W415-1853 / A / 08.17.18

Propane: GX36PTR-1
GX36PTRE-1
GX42PTRE
GX70PTE-1

1.0 getting to know your appliance

DANGER

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

WARNING

The area above the appliance opening including the safety barrier, barrier frame and

the surface of the wall can get very hot during operation and should never be touched

until the appliance is off and completely cooled.

getting to know your appliance

!

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and shall be installed for the protection of children
and other at-risk individuals.

EN

Safety barrier Glass door

note:

Some features and locations may vary depending on the model.

Door trim Valve / rating

Burner

Pilot

plate / lighting

instructions /

battery back up /

anticondensation

W415-1853 / A / 08.17.18

5

EN

Certified to Canadian and American National Standards: CSA 2.22-2016 / ANSI Z21.50-2016 for Vented Decorative Gas Appliances
Certifié selon les normes Nationales Canadiennes et Américaines: CSA 2.22-2016 / ANSI Z21.50-2016 pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas fireplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current
standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance
must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier W565-0307. Follow installation instructions.
Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation
conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured
Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran W565-0307. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

GX42NTRE CX42NTRE CX42PTRE GX42PTRE

MODEL / MODÈLE

Altitude
Input
Reduced Input
P4

Élévation

Alimentation

Alimentation Réduite

P4
Manifold Pressure: 3.5” w.c. (NG)
Minimum Supply Pressure: 4.5” w.c. (NG)
Maximum Supply Pressure: 7”* w.c. (NG)
Pression au Collecteur: 3,5” d’une colonne d’eau (GN)
Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)
Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-4500ft (0-1370m)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and finishing
materials. For non-combustible framing and finishing materials,
see installation manual.
Top 0”
Floor 0”
Sides 0”
Back 0”
Vent top 3”
Vent sides & bottom 1”
Recessed depth 18 9/16”
*** Mantel 8” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de finition.

Dessus 0”
Plancher 0”

Côtés 0”
Arrière 0”

Dessus du conduit d’évent 3”

Côtés et dessous du conduit d’évent 1”
Profondeur d’encastré une face 18 9/16”
*** Tablette 8” de l’ouverture de l’appareil

WARNING

:

Do not add any material to the appliance which will come in contact with the

flames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT

:

N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les flammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension: 2”. See installation manual
for greater extensions, minimum vent lengths and maximum
vent lengths.

*** L’extension horizontale maximale: 2”. Référez au manuel d’installation

pour des extensions plus grandes, les longueurs d’évacuation minimaux et

maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation
manual for venting specifications. Proper reinstallation and resealing is necessary after servicing
the vent-air intake system.
L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au
manuel d’installation pour les spécifications d’évacuation. Il est nécessaire de bien réinstaller et
resceller l’évacuation après avoir executer l’entretien du système de prise d’air.
Optional fan kit: AUB / GZ600KT
Ensemble de ventilateur facultatif: AUB / GZ600KT

Serial Number / N° de Série:

W385-2246 / C

REFERENCE# 161746

GX42

51.27%

22,000

30,000

Electrical rating: 115V, 60HZ. Less than 12 amperes.
Spécifications électriques: 115V, 60HZ. Moins de 12 ampère.

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF
HEAT, NOT INTENDED FOR USE AS A HEATING APPLIANCE,
NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS
UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE
UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE
CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.
POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE
CERTIFIÉES AVEC L’APPAREIL.

24,000

CAUTION:

Hot while in operation. Do not touch. Severe

burns may result. Keep children, clothing,
furniture, gasoline and other liquids having

flammable vapors away.

ATTENTION:

L’appareil est chaud lorsqu’il fonctionne. Ne pas

toucher l’appareil. Risque de brûlures graves.

Surveiller les enfants. Garder les vêtements, les

meubles, l’essence ou autres liquides produisant

des vapeur inflammables loin de l’appareil.

S’assurer que le brûleur et

le compartiment des

commandes sont propres.

Voir les instructions

d’installation et
d’utilisation qui

accompagnent l’appareil.

Par mesure de sécurité,

cet appareil doit être

alimenté en air frais et

avec d’air

comburant et de

ventilation suffisant.

This appliance is only for use with the type of gas
indicated on the rating plate and may be installed
in an aftermarket, permanently located, manufac­tured home (USA only) or mobile home where not

prohibited by local codes. See owner’s manual
for details. This appliance is not convertible for

use with other gases, unless a certified kit is

used.

Cet appareil doit être utilisé uniquement avec le

type de gaz indiqué sur la plaque signalétique.

Cet appareil peut être installé dans une maison
préfabriquée ou mobile (É.U. seulement) installée
à demeure si les règlements locaux le permettent.

Voir la notice de l’utilisateur pour plus de
renseignements. Cet appareil ne peut pas être
utilisé avec d’autres gaz sauf si une trousse de

conversion certifiée est fournie.

FOR YOUR SAFETY:

Do not store or use gasoline or

other flammable vapors and liquids

in the vicinity of this or any other

appliance.

CAUTION:

Do not operate the appliance with

the glass removed, cracked or

broken.

Replacement of the glass should

be done by a licensed or qualified

person.

POUR VOTRE

SÉCURITÉ:

Ne pas entreposer ni utiliser

d’essence ni d’autres vapeurs ou

liquides inflammables dans le

voisinage de cet appareil ou de

tout autre appareil.

ATTENTION:

N’utiliser pas l’appareil si le
panneau frontal en verre est

enlevé, craqué ou brisé.

Remplacement du panneau frontal

en verre doit être fait par un

technicien agréé.

WARNING:

Improper installation,

adjustment, alteration,

service or maintenance can

cause property damage,

personal injury or loss of life.

Refer to owner’s manual.

Installation and service must

be performed by a qualified

installer, service agency or

the gas supplier.

AVERTISSEMENT:

Un installation

ou une modification

inappropriée du réglage, du

service et de l’entretien

pourraient être la cause de

dommages à la propriété de

blessures corporelles ou

même la mort. Consulter le

manuel d’information,

l’installation et le service

doivent être exécutés par un

installateur qualifié pour le

gaz, un entreprise de

service ou le fournisseur de

gaz seulement.

Keep burner and control
compartment clean. See

installation and

operating instructions

accompanying

appliance. Appliance
needs fresh air for safe
operation and must be

installed with adequate

provisions for

combustion and

ventilation air.

SAMPLE

getting to know your appliance

1.1 control access

Access to the control can be done by removing the safety barrier, glass door, door trim and control cover (see
“maintenance” section for instructions on how to remove these components).

VALVE

FLAME ADJUSTMENT

KNOB

1.2 rating plate information

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA 2.33b - 2008, ANSI Z21.88b- 2008 VENTED GAS FIREPLACE HEATER / APPAREIL DE CHAUFFAGE ALIMENTÉ
AU GAZ ET VENTILÉ

UN COMBUSTIBLE SOLIDE NE

VENTED GAS FIREPLACE HEATER. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE
CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24 CFR,

DOIT PAS ÊTRÉ UTILISÉ AVEC

PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A.

MODEL PROPANE

CET APPAREIL. UTILISER AVEC

FOYER DE CHAUFFAGE AU GAZ AVEC ÉVACUATION. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIÉ POUR INSTALLATION DANS UNE

LHD50PT

LES PORTES VITRÉES

MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉES AU GAZ, EN VIGUEUR AU CANADA OU AUX ÉTATS-UNIS DE LA
NORME DE SECURITÉ ET DE CONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ÉTATS-UNIS NE PEUT ÊTRE APPLIQUÉE, SE RÉFÉRER A LA NORME

REFERENCE #
W/N 16131

NOT FOR USE WITH
SOLID FUEL. FOR USE
WITH GLASS DOORS
CERTIFIED WITH THIS
UNIT ONLY.

DO NOT ADD ANY MATERIAL

:

WARNING

TO THE APPLIANCE, WHICH WILL COME
IN CONTACT WITH THE FLAMES, OTHER
THAN THAT SUPPLIED BY THE

MANUFACTURER WITH THE APPLIANCE.

MINIMUM CLEARANCE TO
COMBUSTIBLE MATERIALS:

TOP 0”
FLOOR 0”
RECESSED DEPTH ONE SIDED 23"
RECESSED DEPTH SEE THRU 13.5”
FRAMING (NOT INCLUDING
FACE MATERIAL)
SIDES 0”

VENT 2"
BACK 0”
MANTLE 15" *
TOP, SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING MATERIALS. FOR FINISHING MATERIALS
SEE OWNERS MANUAL
* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION
HORIZONTALE MAXIMALE: 2". SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS.
SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.

ELECTRICAL RATING: 115V 0.82AMP, 60HZ

MADE IN CANADA / FABRIQUÉ AU CANADA

WOLF STEEL LTD. BARRIE, ONTARIO, CANADA

6

note:

The rating plate must remain with the appliance at all times. It must not be removed.

W415-1853 / A / 08.17.18

HOMOLOGUÉES SEULEMENT

RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES SITES ET LES COMMUNAUTÉS, ANSI/NFPA 501A.

AVEC CETTE UNITÉ.

0-4500FT (0-1370M)

MODEL NATURAL GAS /

3.5" WATER COLUMN/D'UNE COLONNE D'EAU

4.5" WATER COLUMN/D'UNE COLONNE D'EAU

7.0" WATER COLUMN/D'UNE COLONNE D'EAU

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE
NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL
FOR VENTING SPECIFICS. PROPER REINSTALLATION AND
RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR

N'AJOUTEZ PAS A

GAZ NATURAL

30,000 BTU/H

AVERTISSEMENT:

LHD50NT

ALTITUDE / ÉLÉVATION

23,000 BTU/H

CET APPAREIL AUCUN MATÉRIAU DEVANT

INPUT / ALIMENTATION

0-4500FT (0-1370M)

#53

ENTRER EN CONTACT AVEC LES FLAMMES

30,000 BTU/H

REDUCED INPUT / ALIMENTATION RÉDUITE

10" WATER COLUMN/D'UNE COLONNE D'EAU

AUTRE QUE CELUI QUI EST FOURNI AVEC

ORIFICE / INJECTEUR

23,000 BTU/H

CET APPAREIL PAR LE FABRICANT.

#38

MANIFOLD PRESSURE /

DÉGAGEMENTS MINIMAUX DES

11" WATER COLUMN/D'UNE COLONNE D'EAU

PRESSION AU COLLECTEUR

MATÉRIAUX COMBUSTIBLES:

DESSUS 0”

MINIMUM SUPPLY PRESSURE /

13" WATER COLUMN/ D'UNE COLONNE D'EAU

PROFONDEUR D'ENCASTRÉ 25"

PRESSION D'ALIMENTATION MINIMALE

PLANCHER 0”

MAXIMUM SUPPLY PRESSURE /

ÉVENT 2"

PRESSION D'ALIMENTATION MAXIMALE

CÔTES 0”

L'APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT L'ENSEMBLE

MANTEAU 15" *

D'ÉVACUATION PROPRE A NAPOLEON. RÉFÉRER AU MANUEL

ARRIÉRE 0”
D'INSTALLATION DE PROPRIÉTAIRE POUR L'ÉVACUATION
PRÉCISE. IL EST IMPORTANT DE BIEN RÉINSTALLER ET
RESCELLER L'ÉVENT APRÈS AVOIR ASSURÉ LE MAINTIEN DU
SYSTÉME DE PRISE D'AIR.

INTAKE SYSTEM.

DESSUS, COTÉS & ARRIÈRE: SELON LES ESPACEURS DE DÉGAGEMENT POUR LES MATÉRIAUX D'OSSATURE
SELON LE MANUEL DE PROPRIÉTAIRE POUR LES MATÉRIAUX DE FINITION.
* L'EXTENSION HORIZONTALE MAXIMALE: 2". RÉFÉRER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS
PLUS GRANDES. RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTAIRE.

CLASSIFICATION: 115V 0.82AMP, 60HZ

W385-2007

SERIAL NUMBER/NO. DE SÉRIE: LV50

2.0 operating your appliance

When operating your appliance for the first time, there is a required burn-in process that cures materials used
to manufacture the appliance that may emit both vapors and an odor. These are normal when operating a new
appliance for the first time. Ensure adequate air circulation is provided during burn-in process, if this was not
completed by the installer during installation.

operating your appliance

2.1 using your appliance

To turn the appliance on:

A Turn the on/off switch on (see below).
B After 3-5 seconds, the control will start a spark at the pilot, light the pilot and then the burner. The spark

period will last 60 seconds, or until the pilot has lit.

C When used for the first time, if the burn-in process was not completed by the installer; run appliance

continuously for 4 hours (burn-in).

D Turn the appliance off. Wait until appliance is completely cool before moving to the next step.

E Remove the safety barrier and firebox glass door. Clean firebox glass door (see “maintenance” section).

Replace firebox glass door and safety barrier.

For more detailed information, see your installation manual or contact your authorized dealer.

2.2 on/off components

EN

| On/off switch | Battery holder | Battery holder (including switch) | Remote control

(Not supplied)

Batteries must be disposed of according to the local laws and regulations. Some batteries may be
recycled, and may be accepted for disposal at your local recycling center. Check with your
municipality for recycling instructions.

(Optional for GX36-1 and

GX42)

(Standard for GX70-1)

(Optional for GX36-1 and

GX42)

(Standard for GX70-1)

W415-1853 / A / 08.17.18

7

EN

operating your appliance

2.2.1 changing the batteries in the battery holder

WARNING

!

• Ensure the gas and electrical power to the appliance is turned off.

• Appliance may be hot, do not service until the appliance has cooled.

note:

In the event of a power failure, your appliance can be operated using the supplied battery back-up. If a power
failure occured, remove the batteries from the holder once the power has been restored.

A. Turn off the gas and disconnect the electrical power supply from the appliance.
B. Remove the safety barrier, control cover and door trim to easily access the control compartment (see

“maintenance” section for instructions on how to remove these components).

C. Locate the battery housing located near the control board (see illustration below).
D. Open the battery housing by sliding the back piece upwards and off of the battery housing. Remove the

four “AA” alkaline batteries and install four new “AA” alkaline batteries into the battery housing. Ensure the
positive and negative ends correspond with those identified on the holder.

E. Place the battery housing back into the control compartment, ensure that the battery housing is placed in

a clean and easily accessible location.

F. Reinstall the safety barrier. The safety barrier must be installed at all times during the appliance operation.
G. Turn the gas and electrical power back on to begin operating the appliance.

Red wire

Red wire

Control module

Control module

Black wire

Black wire

Battery housing

Battery housing

8

W415-1853 / A / 08.17.18

operating your appliance

2.2.2 turndown (GX36-1 & GX42 only)

Manual adjustments to your appliance must only be made when the appliance is off and completely
cool. Allow safety barrier to cool before making adjustment.

The GX36-1 and GX42 models are equipped with a manual gas control knob (located on the valve) that adjusts
the flame height to suit your preference. To access the gas control knob, remove your safety barrier, control cover
and door trim (see “maintenance” section for instructions on how to remove these components.

Use only your hand to turn the gas control knob (never use tools). If the knob will not turn by hand, do not try to
repair it. Contact a qualified technician.

O

L

Flame adjustment

H

I

EN

An optional remote control is available to turn the appliance on and off and to adjust the flame height without the
need to remove the safety barrier, refer to the instructions provided with the remote control.

W415-1853 / A / 08.17.18

9

EN

3.0 clearances around appliance

clearances around fireplace

WARNING

!

• Your appliance, gas/electrical connections, venting and various key components are hidden behind the wall. It is
critical that no screws penetrate these components. Failure to follow instructions may cause improper operation,
damage, personal injury or fire. Always use a stud finder and only screw into studs.

Without making adequate provisions to account for the heat, the temperatures above the appliance will be hot,
making it unsuitable for mounting a TV or other objects sensitive to heat without risk of damage.

Installing a mantel between this appliance and electronics or other materials that may be sensitive to heat will reduce
the effect of direct heat on them.

The size and material of the mantel will affect the allowable clearance above your appliance and incorrect placement
could become a fire hazard. Consult your installation manual and/or authorized dealer for more information before
mounting a mantel, a shelf or any other object above your appliance.

Your appliance, gas/electrical connections and vent are hidden directly behind the finished wall. Great care should be
taken to avoid screwing or nailing into these components. Always use a stud finder to determine stud location and
only screw into studs.

Do not screw into the area around the appliance opening as some of your appliance may be hidden behind the
finished wall. Refer to your installation manual and/or contact your local dealer for more information.

Fireplaces

generate radiant

heat. Do not put

objects in front

of the appliance

(minimum

distance of 4 feet

[1.21m]).

WARNING

!

The area above an appliance gets hot.

Combustible objects or materials must

never be placed in this area. For mini-

mum clearances, refer to installation

manual or your authorized dealer.

10

W415-1853 / A / 08.17.18

A

See “minimum clearance
to mantle” section
(installation manual).

Flush installation without mantel

TV bracket

clearances around fireplace

Partially recessed installation with mantel

6” min.

TV bracket

2.5” min.

2” min. (3” max. recommended)

EN

Enclosure

Top of
finishing
flange

Appliance

(fireplace
opening)

Recessed installation with protrusion

6” min.

TV bracket

2.5” min.

2” min. (3” max. recommended)

Enclosure

Top of finishing flange

(fireplace opening)

Appliance

Enclosure

Appliance

A

Top of finishing flange

(fireplace opening)

Flush installation with mantel

6” min.

TV bracket

2.5” min.

2” min. (3” max. recommended)

Enclosure

Appliance

A

Top of finishing flange

(fireplace opening)

note:

• These are recommended minimum clearances only and are in supplied in good faith and not a guarantee
of compliance with TV manufacturers’ maximum allowable operating temperatures. Always comply to TV
manufacturers’ requirements.

• TV temperatures must be validated at the time of installation as air flow characteristics within the
room can vary and maximum acceptable operating temperatures can vary from appliance to appliance.
TVs cannot be used where the TV temperature exceeds the manufacturer’s maximum allowable operating
temperatures (see TV manufacturer’s specifications).

• Mantel height and depth must conform to mantel clearance requirements specified in this manual, see
“minimum clearance to combustible mantel” section in installation manual.

• Dimension “A” the gap between the top of the finishing flange and the bottom of the TV are taken from the
top of the appliance opening.

• TV temperatures may be further reduced by increasing the horizontal distance between the front of the TV
and the front edge of the mantel or by increasing dimension “A”. However, increasing the gap between the
top of the mantel and the bottom of the TV beyond the maximum recommended figure, typically results in
higher temperatures. Minimum clearance between the mantel and bottom of the TV should be maintained to
allow air circulation below and behind the TV.

W415-1853 / A / 08.17.18

11

EN

maintenance4.0 maintenance

WARNING

!

• Turn off the gas and electrical power before servicing the appliance.

• Appliance may be hot. Do not service until appliance has cooled.

For qualified technicians only:

• Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous
operation. Verify proper operation after servicing.

• This appliance and its venting system should be inspected before use and at least annually by a qualified service
person.

• The flow of combustion and ventilation air must not be obstructed.

DOS

• Clean your safety barrier or regularly to prevent
the build up of excessive lint/dust from carpeting,
pet hair, etc. Simply vacuum using the brush
attachment.

• Always use ammonia-free glass cleaners.

• Service your appliance annually and/or as
required. Service must be conducted by a qualified
technician.

• Keep your appliance area clear and free of
combustible materials, gasoline, or other flammable
vapors and liquids.

• Check to see that the burner ignites completely
on all openings when turned on. A 5 to 10 second
total light-up period is satisfactory. Service as
required.

note:

For any questions and/or concerns regarding your appliance, maintenance and service, please contact your
authorized dealer.

DON’TS

• Attempt to service the electrical or gas
components. Contact a qualified technician.

• Use excessive force.

• Use abrasive cleaners on glass.

• Paint the pilot assembly.

• Place objects too close to the appliance opening.

12

W415-1853 / A / 08.17.18

maintenance

WARNING

If the appliance is equipped with plated parts, you must clean fi ngerprints or other marks from the plated surfaces

4.1 care of glass

!

• Do not clean glass when hot! Do not use abrasive cleaners to clean glass.

Buff lightly with a clean dry soft cloth to remove accumulated dust or fi ngerprints. Clean both sides of the glass
after the fi rst 10 hours of operation with an ammonia-free glass cleaner.

note:

Vinegar-based glass cleaners have demonstrated an ability to provide a clean, streak free glass surface.

Thereafter, clean as required. If the glass is not kept clean permanent discoloration and / or blemishes may
result. Contact you local authorized dealer / distributor for complete cleaning instructions.

Razor blades, steel wool, or other metallic objects must not be used on both surfaces of the glass. Doing so
can remove a thin layer of metal from the razor blades, steel wool, or other metallic objects that may then be
deposited onto the coating. This can result in a discoloured stain or scratch-like mark. More importantly, this can
scratch the glass surface, thereby reducing its strength.

Do not operate the appliance with broken glass, as leakage of fl ue gases may result.
Contact your local authorized dealer / distributor for complete cleaning instructions.
If the glass should ever crack or break while the fi re is burning, do not open the door until the fi re is out. Do not

operate the appliance until the glass has been replaced. Contact you local authorized dealer / distributor for
replacement parts. DO NOT SUBSTITUTE MATERIALS.

Replacement glass/frame assembly shall be replaced as a complete unit as supplied by the appliance
manufacturer.

EN

This appliance is factory equipped with 5mm ceramic glass. Use only replacement parts as supplied by the
appliance manufacturer. DO NOT SUBSTITUTE MATERIALS.

4.2 care of plated parts

before operating the appliance for the fi rst time. Use an ammonia-free or vinegar-based cleaner and a towel
to clean. If not cleaned properly before operating for the fi rst time, the marks can cause permanent blemishes
on the plating. After the plating is cured, the fi ngerprints and oils will not affect the fi nish and little maintenance
is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause
discolouration on plated parts.

note:

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can
be improved if the assembly is warmed (i.e. using a hair dryer or similar heat source).

W415-1853 / A / 08.17.18

13

EN

!

WARNING

maintenance

4.3 safety barrier removal

• Glass may be hot. Do not touch glass until cooled.

• If equipped with door latches that are part of a safety system, they must be properly engaged. Do not
operate the appliance with latches disengaged.

• Facing and/or fi nishing materials must not interfere with air fl ow through air openings, louvre openings,
operation of louvres, or doors/access for service. Observe all clearances when applying combustible
materials.

• Before door is removed, turn the appliance off and wait until appliance is cool to the touch. Doors are heavy
and fragile so handle with care.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the
appliance and must be installed.

Before the glass door can be removed, the safety screen must be removed. Lift the safety screen off the four
pins, tilt the top forward and remove from the appliance.

SAFETY SCREEN

SAFETY SCREEN

4.4 firebox glass door removal

Leave a hand on the glass door during entire door removal. The glass door is secured to the firebox with four
spring latches. Pull the handles of the latches forward, then lift the latches out from the door frame to release the
door. Next, lift the door up until the bottom edge clears the bottom shoulder screws of the appliance. Carefully
grip the top and bottom of the door lifting it off the appliance.

note:

These spring latches make up the spring relief system for
the appliance. Ensure the door opens freely and closes
sealed.

note:

When mounting the door, ensure there is equal space
on both the left and the right side. This allows for easy
installation of the front.

Reverse these steps to reinstall the door. Ensure safety screen
is installed correctly.

14

W415-1853 / A / 08.17.18

5.0 replacement parts

WARNING

replacements

!

• Failure to position the parts in accordance with this manual or failure to use only parts specifi cally approved
with this appliance may result in property damage or personal injury.

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can
be ordered through your Authorized dealer / distributor.

For warranty replacement parts, a photocopy of the original invoice will be required to honour the
claim.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

Parts, part numbers, and availability are subject to change without notice.
Parts identifi ed as stocked will be delivered within 2 to 5 business days for most delivery

destinations.
Parts not identifi ed as stocked will be delivered within a 2 to 4 week period, for most cases.
Parts identifi ed as ‘SO’ are special order and can take up to 90 days for delivery.

Consult your installation manual for replacement parts.

EN

W415-1853 / A / 08.17.18

15