INSTINST
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
INST
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
INSTINST
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
CAN 1-2.1-M86, AND ANSI Z21.50-1996 RESPECTIVELY FOR GAS-FIRED VENTED ROOM HEATER AND VENTED DECORATIVE GAS APPLIANCE
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS,
GAS STOVEGAS STOVE
GAS STOVE
GAS STOVEGAS STOVE
INSTINST
ALLAALLA
INST
INSTINST
TION AND OPERATION AND OPERA
ALLA
TION AND OPERA
ALLAALLA
TION AND OPERATION AND OPERA
GAS-FIRED STOVEGAS-FIRED STOVE
GAS-FIRED STOVE
GAS-FIRED STOVEGAS-FIRED STOVE
TION INSTRUCTIONS FORTION INSTRUCTIONS FOR
TION INSTRUCTIONS FOR
TION INSTRUCTIONS FORTION INSTRUCTIONS FOR
GS3500 - NGS3500 - N
GS3500 - N
GS3500 - NGS3500 - N
GS3500 - PGS3500 - P
GS3500 - P
GS3500 - PGS3500 - P
WW
ARNING:ARNING:
W
ARNING:
WW
ARNING:ARNING:
NATURAL GAS MODEL
PROPANE GAS MODEL
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI / AGA / CGA METHODS
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to this manual. For assistance or additional
information consult a qualified installer, service agency or the gas supplier.
FOR YOUR SAFETYFOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETYFOR YOUR SAFETY
Do not store or use gasoline or other flammable vapours and liquids in the vicinity of
this or any other appliance.
WHAWHA
TT
T T
WHA
WHAWHA
• Turn off main gas supply.
• Open windows.
• Do not try to light any appliance.
• Do not touch any electrical switch; Do not use
any phone in your building.
O DO IF YOU SMELLO DO IF YOU SMELL
T
T
O DO IF YOU SMELL
TT
T T
O DO IF YOU SMELLO DO IF YOU SMELL
• Extinguish any open flame.
• Immediately call your gas supplier from a
neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the
fire department.
GAS: GAS:
GAS:
GAS: GAS:
Wolf Steel Ltd., RR#1, 9 NAPOLEON RD.,
Barrie, ON., Canada L4M 4Y8 (705)721-1212
ISO 9002 CERTIFIED
Fax: (705)722-6031 Email: ASK@NAPOLEON.ON.CA
Web: WWW .NAPOLEON.ON.CA
R-2000
Registered Quality
System
RRRR
WORLD RECOGNITION FOR QUALITY
WS-415-55 / 11.10.97
2
PGPG
PG
PGPG
PLEASE RET AIN THIS MANUAL FOR FUTURE REFERENCE
2-42-4
INTRODUCTIONINTRODUCTION
2-4
INTRODUCTION
2-42-4
INTRODUCTIONINTRODUCTION
Warranty
General Instructions
General Information
Care of Glass, Enamelled & Plated Parts
5-65-6
VENTINGVENTING
5-6
VENTING
5-65-6
VENTINGVENTING
Location
Chimney Installation
Installing "B" Vent
Adding Vent Sections
Flashing & Storm Collar Installation
Combustion Air
66
GAS INSTGAS INST
6
GAS INST
66
GAS INSTGAS INST
77
OPTIONAL BLOWER INSTOPTIONAL BLOWER INST
7
OPTIONAL BLOWER INST
77
OPTIONAL BLOWER INSTOPTIONAL BLOWER INST
ALLAALLA
ALLA
ALLAALLA
TIONTION
TION
TIONTION
TT
ABLE ABLE
T
ABLE
TT
ABLE ABLE
ALLAALLA
ALLA
ALLAALLA
ofof
CONTENTS CONTENTS
of
CONTENTS
ofof
CONTENTS CONTENTS
PGPG
PG
PGPG
TIONTION
TION
TIONTION
88
8
88
9-109-10
9-10
9-109-10
1111
11
1111
11-1211-12
11-12
11-1211-12
13-1413-14
13-14
13-1413-14
FINISHINGFINISHING
FINISHING
FINISHINGFINISHING
Ornamental Trivet
Log Placement / Charcoal Embers
OPERAOPERA
OPERA
OPERAOPERA
ADJUSTMENTSADJUSTMENTS
ADJUSTMENTS
ADJUSTMENTSADJUSTMENTS
REPLACEMENTSREPLACEMENTS
REPLACEMENTS
REPLACEMENTSREPLACEMENTS
TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TION / MAINTENANCETION / MAINTENANCE
TION / MAINTENANCE
TION / MAINTENANCETION / MAINTENANCE
Spill Switch
Venting Action Check
Operating Instructions
Maintenance
Pilot Burner Adjustment
Venturi Adjustment
Ordering Replacement Parts
Replacement Parts
Accessories
PURGE ALL GAS LINES WITH THE GLASS DOOR OF THE STOVE REMOVED. ASSURE THAPURGE ALL GAS LINES WITH THE GLASS DOOR OF THE STOVE REMOVED. ASSURE THA
PURGE ALL GAS LINES WITH THE GLASS DOOR OF THE STOVE REMOVED. ASSURE THA
PURGE ALL GAS LINES WITH THE GLASS DOOR OF THE STOVE REMOVED. ASSURE THAPURGE ALL GAS LINES WITH THE GLASS DOOR OF THE STOVE REMOVED. ASSURE THA
THE BURNER BEFORE INSTTHE BURNER BEFORE INST
THE BURNER BEFORE INST
THE BURNER BEFORE INSTTHE BURNER BEFORE INST
UNDER EXTREME VENT CONFIGURAUNDER EXTREME VENT CONFIGURA
UNDER EXTREME VENT CONFIGURA
UNDER EXTREME VENT CONFIGURAUNDER EXTREME VENT CONFIGURA
• Do not burn wood or other materials in this stove.
• Adults and especially children should be alerted to the hazards of high surface temperatures and should stay away to
avoid burns or clothing ignition. Supervise young children when they are in the same room as the stove.
• Due to high temperatures, the stove should be located out of traffic and away from furniture and draperies.
• Clothing or other flammable material should not be placed on or near the stove.
• Any safety screen or guard removed for servicing must be replaced prior to operating the stove.
• It is imperative that the control compartments, burners and circulating blower and its passageway in the stove and venting
system are kept clean. The stove and its venting system should be inspected before use and at least annually by a qualified
service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The
stove area must be kept clear and free from combustible materials, gasoline and other flammable vapours and liquids.
• Under no circumstances should this stove be modified.
• This stove must not be connected to a chimney flue pipe serving a separate solid fuel burning appliance.
• Do not use this stove if any part has been under water. Immediately call a qualified service technician to inspect the stove
and to replace any part of the control system and any gas control which has been under water.
• Do not operate the stove with the glass door removed, cracked or broken. Replacement of the glass should be done by a
licensed or qualified service person.
• Do not strike or slam shut the stove glass door.
WS-415-55 / 11.10.97
TIONS, ALLOW SEVERAL MINUTES (5-15) FOR THE FLAME TO STTIONS, ALLOW SEVERAL MINUTES (5-15) FOR THE FLAME TO ST
TIONS, ALLOW SEVERAL MINUTES (5-15) FOR THE FLAME TO ST
TIONS, ALLOW SEVERAL MINUTES (5-15) FOR THE FLAME TO STTIONS, ALLOW SEVERAL MINUTES (5-15) FOR THE FLAME TO ST
WARNINGWARNING
WARNING
WARNINGWARNING
ALLING THE DOOR.ALLING THE DOOR.
ALLING THE DOOR.
ALLING THE DOOR.ALLING THE DOOR.
T A CONTINUOUS GAS FLOW IS AT A CONTINUOUS GAS FLOW IS A
T A CONTINUOUS GAS FLOW IS A
T A CONTINUOUS GAS FLOW IS AT A CONTINUOUS GAS FLOW IS A
ABILIZE AFTER IGNITION.ABILIZE AFTER IGNITION.
ABILIZE AFTER IGNITION.
ABILIZE AFTER IGNITION.ABILIZE AFTER IGNITION.
TT
T
TT
NAPOLEON gas fireplaces are manufactured under the strict Standard of the world recognized
ISO9002 Quality Assurance Certificate.
NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen who
take great pride in their work. The burner and valve assembly are leak and test-fired at a quality test station. The
complete fireplace is thoroughly inspected by a qualified technician before packaging to ensure that you, the customer, receives the quality product that you expect from NAPOLEON.
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTYNAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTYNAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
3
The following materials and workmanship in your new The following materials and workmanship in your new
The following materials and workmanship in your new
The following materials and workmanship in your new The following materials and workmanship in your new
ranted against defects for as long as you own the fireplace. This covers: combustion chamber,ranted against defects for as long as you own the fireplace. This covers: combustion chamber,
ranted against defects for as long as you own the fireplace. This covers: combustion chamber,
ranted against defects for as long as you own the fireplace. This covers: combustion chamber,ranted against defects for as long as you own the fireplace. This covers: combustion chamber,
heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-
heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-
heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal break-heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal breakage only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-age only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-
age only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-
age only), gold plated parts against tarnishing, porcelainized enamelled components and alumi-age only), gold plated parts against tarnishing, porcelainized enamelled components and aluminum extrusion trims.num extrusion trims.
num extrusion trims.
num extrusion trims.num extrusion trims.
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly arethermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly arethermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
covered and covered and
covered and
covered and covered and
of the limited warranty.of the limited warranty.
of the limited warranty.
of the limited warranty.of the limited warranty.
Labour related to warranty repair is covered free of charge during the first year. RepairLabour related to warranty repair is covered free of charge during the first year. Repair
Labour related to warranty repair is covered free of charge during the first year. Repair
Labour related to warranty repair is covered free of charge during the first year. RepairLabour related to warranty repair is covered free of charge during the first year. Repair
work, however, requires the prior approval of an authorized company official. Labour costs towork, however, requires the prior approval of an authorized company official. Labour costs to
work, however, requires the prior approval of an authorized company official. Labour costs to
work, however, requires the prior approval of an authorized company official. Labour costs towork, however, requires the prior approval of an authorized company official. Labour costs to
the account of the account of
the account of
the account of the account of
must be done through an authorized must be done through an authorized
must be done through an authorized
must be done through an authorized must be done through an authorized
All specifications and designs are subject to change without prior notice due to on-going product improvements. Napoleon® is a registered trademark of wolf steel ltd. Patents
u.s. 5.303.693.801 - can. 2.073.411, 2.082.915. © wolf steel ltd.
NAPOLEON warrants its products against manufacturing defects to the original purchaser only -- i.e., the individual or legal entity (registered customer) whose name appears on the
warranty registration card filed with NAPOLEON -- provided that the purchase was made through an authorized NAPOLEON dealer and is subject to the following conditions and
limitations:
This factory warranty is nontransferable and may not be extended whatsoever by any of our representatives.
The gas fireplace must be installed by a licenced, authorized service technician or contractor. Installation must be done in accordance with the installation instructions included with
the product and all local and national building and fire codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from other manufacturers will nullify
this warranty.
This limited warranty further does not cover any scratches, dents, corrosion or discolouring caused by excessive heat, abrasive and chemical cleaners nor chipping on porcelain enamel
parts, mechanical breakage of PHAZER™ logs and embers, nor any venting components used in the installation of the fireplace.
NAPOLEON warrants its stainless steel burners against defects in workmanship and material for life, subject to the following conditions: During the first 10 years NAPOLEON will
replace or repair the defective parts at our option free of charge. From 10 years to life, NAPOLEON will provide replacement burners at 50% of the current retail price.
In the first year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the product has been operated
in accordance with the operation instructions and under normal conditions.
After the first year, with respect to this President's Limited Lifetime Warranty , NAPOLEON may , at its discretion, fully discharge all obligations with respect to this warranty by refunding
to the original warranted purchaser the wholesale price of any warranted but defective part(s).
After the first year, NAPOLEON will not be responsible for installation, labour or any other costs or expenses related to the reinstallation of a warranted part, and such expenses are
not covered by this warranty.
Notwithstanding any provisions contained in this President's Limited Lifetime Warranty, NAPOLEON’S responsibility under this warranty is defined as above and it shall not in any
event extend to any incidental, consequential or indirect damages.
This warranty defines the obligations and liability of NAPOLEON with respect to the NAPOLEON gas fireplace and any other warranties expressed or implied with respect to this
product, its components or accessories are excluded.
NAPOLEON neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product. NAPOLEON will not be responsible
for: over-firing, downdrafts, spillage caused by environmental conditions such as rooftops, buildings, nearby trees, hills, mountains, inadequate vents or ventilation, excessive venting
configurations, insufficient makeup air, or negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc.
Any damages to fireplace, combustion chamber, heat exchanger, brass trim or other component due to water, weather damage, long periods of dampness, condensation, damaging
chemicals or cleaners will not be the responsibility of NAPOLEON.
The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized dealer. The warranty registration
card must be returned within fourteen days to register the warranty.
NAPOLEON reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim.
NAPOLEONNAPOLEON
NAPOLEON
NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON
NAPOLEONNAPOLEON
will provide replacement parts free of charge during the first yearwill provide replacement parts free of charge during the first year
will provide replacement parts free of charge during the first year
will provide replacement parts free of charge during the first yearwill provide replacement parts free of charge during the first year
are based on a predetermined rate schedule and any repair work are based on a predetermined rate schedule and any repair work
are based on a predetermined rate schedule and any repair work
are based on a predetermined rate schedule and any repair work are based on a predetermined rate schedule and any repair work
NAPOLEONNAPOLEON
NAPOLEON
NAPOLEONNAPOLEON
CONDITIONS AND LIMITCONDITIONS AND LIMIT
CONDITIONS AND LIMIT
CONDITIONS AND LIMITCONDITIONS AND LIMIT
dealer. dealer.
dealer.
dealer. dealer.
NAPOLEONNAPOLEON
NAPOLEON
NAPOLEONNAPOLEON
AA
TIONSTIONS
A
TIONS
AA
TIONSTIONS
gas fireplace are war- gas fireplace are war-
gas fireplace are war-
gas fireplace are war- gas fireplace are war-
WS-415-55 / 11.10.97
4
INTRODUCTION
GENERAL INSTRUCTIONSGENERAL INSTRUCTIONS
GENERAL INSTRUCTIONS
GENERAL INSTRUCTIONSGENERAL INSTRUCTIONS
THIS GAS STOVE SHOULD BE INST ALLED AND SERVICED BY A QUALIFIED INST ALLER to conform with local codes.
In absence of local codes, install to the current CAN1-B149 Installation Code in Canada or to the National Fuel Gas Code, ANSI
Z223.1-1988, and NFPA 54-1988 in the United States.
The stove and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing
of that system at test pressures in excess of 1/2 psig (3.5 kPa). The stove must be isolated from the gas supply piping system
by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures
equal to or less than 1/2 psig (3.5 kPa).
A 1/8 inch NPT plug, accessible for test gauge connection, must be installed immediately upstream of the gas supply connection to the stove.
This stove must be connected to either a 4" 'B' vent system or any accepted lined chimney system using a liner and vent
connector listed to ULC-S635M (in Canada) or UL-1777 (in USA). The venting connection must be in compliance with the vent
manufacturers installation instructions.
The stove, when installed with a blower, must be electrically connected and grounded in accordance with local codes. In the
absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the ANSI/NFPA 70-1990
NA TIONAL ELECTRICAL CODE in the United States. The blower power cord must be connected into a properly grounded
receptacle. The grounding prong must not be removed from the cord plug.
Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing and operating the
stove. Never obstruct the front opening of the stove.
GENERAL INFORMAGENERAL INFORMA
GENERAL INFORMA
GENERAL INFORMAGENERAL INFORMA
FOR YOUR SATISFACTION, THIS STOVE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND QUALITY!
Maximum input is 30,000 BTU/hr for natural gas and 24,000 BTU/hr for propane. When the fireplace is installed at elevations
above 4,500ft, and in the absense of specific recommendations from the local authority having jurisdiction, the certified high
altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft. Maximum output for natural gas is 22,500
BTU/hr at an efficiency of 75% with the fan on, 70% with the fan off; and 18,500 BTU/hr for propane at an efficiency of 77% with
the fan on, 72% with the fan off. The efficiency rating of the fireplace is a product thermal efficiency rating, determined independently of any installed system under continuous conditions and
applies to Canada only.
Where the stove has been factory equipped for hi-altitude using natural gas, the input has
been downrated by 10%. Hi-altitude downrating for propane is
not necessary.
Minimum inlet gas supply pressure is 4.5 inches water column
for natural gas and 11 inches
water column for propane. Maximum inlet gas pressure is 7
inches water column for natural
gas and 13 inches water column
for propane. Manifold pressure
under flow conditions is 3.5
inches water column for natural gas and 10 inches water column for propane.
NO EXTERNAL ELECTRICITY (110 VOL TS OR 24 VOL TS) IS REQUIRED FOR THE GAS SYSTEM OPERA TION. Change
in flame appearance from "HI" to "LO" is more evident in natural gas than in propane. Models GS 3500N and GS 3500P are
certified for bedroom and bed-sitting room installations. Expansion / contraction noises during heating up and cooling down
cycles are normal and to be expected.
CARE OF GLASS, PLACARE OF GLASS, PLA
CARE OF GLASS, PLA
CARE OF GLASS, PLACARE OF GLASS, PLA
Do not use abrasive cleaners to clean these parts. Buff lightly with a clean dry cloth. Porcelain enamelled components must
be handled with care. The baked-on finish is glass-like. If struck, it will chip! T ouch-up paint is available through your Napoleon
dealer.
The glass is 3/16" ceramic glass available from your Napoleon / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS.
Clean the glass after the first 10 hours of operation with a recommended glass cleaner specifically formulated for gas fireplaces or a non-abrasive, ammonia or vinegar-based glass cleaner. Thereafter clean as required. DO NOT CLEAN GLASS
WHEN HOT! If the glass is not kept clean permanent discolouration and / or blemishes may result.
TIONTION
TION
TIONTION
TED AND ENAMELLED PTED AND ENAMELLED P
TED AND ENAMELLED P
TED AND ENAMELLED PTED AND ENAMELLED P
ARAR
AR
ARAR
TSTS
TS
TSTS
WS-415-55 / 11.10.97
VENTING
LOCALOCA
TIONTION
LOCA
TION
LOCALOCA
TIONTION
The most desirable and benefical location for a Napoleon Stove is in the centre of a building, thereby allowing the most efficient
use of the heat created. The location of windows, doors and the traffic flow in the room where the stove is to be located should
be considered. If possible, you should choose a location where the chimney will pass through the house without cutting a floor
or roof joist.
MAINT AIN THESE MINIMUM CLEARANCES TO COMBUSTIBLES:
A. 8"
B. 5"
C. 1"
D. 1" 'B' vent or 6" single
wall vent connector
E. 7"
F. 11"
minimum 18" from stove top to ceiling
NO ADDITIONAL FLOOR PROTECTION IS REQUIRED.NO ADDITIONAL FLOOR PROTECTION IS REQUIRED.
NO ADDITIONAL FLOOR PROTECTION IS REQUIRED.
NO ADDITIONAL FLOOR PROTECTION IS REQUIRED.NO ADDITIONAL FLOOR PROTECTION IS REQUIRED.
5
CHIMNEY INSTCHIMNEY INST
CHIMNEY INST
CHIMNEY INSTCHIMNEY INST
ALLAALLA
TION TION
ALLA
ALLAALLA
A CHIMNEY VENTING THIS STOVE SHALL NOT VENT ANY SOLID FUEL BURNING APPLIANCE.
ALL HORIZONTALL HORIZONT
ALL HORIZONT
ALL HORIZONTALL HORIZONT
THREE TYPES OF CHIMNEY SYSTEMS MAY BE USED WITH THIS STOVE:
TION
TION TION
AL RUNS MUST HAAL RUNS MUST HA
AL RUNS MUST HA
AL RUNS MUST HAAL RUNS MUST HA
VE A 1/4 INCH RISE PER FOOTVE A 1/4 INCH RISE PER FOOT
VE A 1/4 INCH RISE PER FOOT
VE A 1/4 INCH RISE PER FOOTVE A 1/4 INCH RISE PER FOOT
FIGURE 1
..
.
..
INST ALLING 'B' VENT:
1.Move the stove into position. Try to center the exhaust of the stove,
midway between two joist to prevent having to cut them. Use a plumb
bob to line up the center.
2. Cut and frame an opening in the roof to provide a 1"
clearance between the outside of the 'B' vent and
any combustible material. DO NOT FILL THIS
SP ACE WITH ANY TYPE OF MATERIAL. Nail headers between the joist for extra support. Firestop spacers must be placed on the bottom of each framed
opening in any floor or on top of any framed opening
in any attic that the 'B' vent passes through. FIG-
URE 2.
3. Hold a plumb bob from the underside of the roof to
determine where the opening in the roof should be.
Cut and frame the roof opening to maintain proper 1"
clearances. FIGURE 3
For aesthetics, a 6" telescoping stove pipe may be
installed over the 4" vent connection or 'B' vent. Either use a Napoleon stove pipe adapter available from your Napoleon dealer
or cut approximately 2" from the crimped end of the 6" diameter chimney section to be inserted into the 6-1/4" canopy opening.
FIGURE 2
FIGURE 3
WS-415-55 / 11.10.97