Napoleon GD82NT-T, GD82PT-T, GD82PT-PA, GD82NT-PA Installation And Operating Instructions Manual

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

GD82NT-T

SAFETY INFORMATION

!

WARNING

If the information in these instructions
are not followed exactly, a fi re or
explosion may result causing property
damage, personal injury or loss of life.

NATURAL GAS

GD82PT-T

PROPANE

1

- Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any
other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use
any phone in your building.

• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call the
fi re department.

- Installation and service must be performed by a

qualifi ed installer, service agency or the supplier.

This appliance may be installed as an OEM
installation in manufactured home (USA only) or
mobile home and must be installed in accordance
with the manufacturer’s instructions and the
Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280, in the United
States or the Standard for Installation in Mobile
Homes, CAN/CSA Z240 MH, in Canada.

This appliance is only for use with the type(s) of
gas indicated on the rating plate. A conversion kit
is supplied with the appliance.

!

WARNING

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone [phone] • Fax [phone] • www.napoleonfi replaces.com • [e-mail]

$10.00

1.28A

W415-0769 / A / 12.10.10

2

TABLE OF CONTENTS

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

2.1 DIMENSIONS 5

2.2 GENERAL INSTRUCTIONS 5

2.3 GENERAL INFORMATION 7

2.4 RATING PLATE INFORMATION 7

3.0 VENTING 8

3.1 VENTING LENGTHS AND COMPONENTS 9

3.2 TYPICAL VENT INSTALLATION 10

3.3 SPECIAL VENT INSTALLATIONS 11

3.3.1 PERISCOPE TERMINATION 11

3.4 MINIMUM AIR TERMINAL LOCATION CLEARANCES 12

3.5 VENTING APPLICATION FLOW CHART 13

3.6 DEFINITIONS 13

3.7 ELBOW VENT LENGTH VALUES 13

3.8 HORIZONTAL TERMINATION 14

3.9 VERTICAL TERMINATION 16

4.0 INSTALLATION 18

4.1 WALL AND CEILING PROTECTION 18

4.1.1 HORIZONTAL INSTALLATION 19

4.1.2 VERTICAL INSTALLATION 19

4.2 USING FLEXIBLE VENTING COMPONENTS 20

4.2.1 HORIZONTAL AIR TERMINAL INSTALLATION 20

4.2.2 VERTICAL AIR TERMINAL INSTALLATION 21

4.2.3 APPLIANCE VENT CONNECTION 22

4.3 USING RIGID VENT COMPONENTS 22

4.3.1 HORIZONTAL AIR TERMINAL INSTALLATION 22

4.3.2 EXTENDED HORIZONTAL AIR TERMINAL INSTALLATION 22

4.3.3 VERTICAL AIR TERMINAL INSTALLATION 23

4.4 GAS INSTALLATION 24

4.5 MOBILE HOME INSTALLATION 25

5.0 FRAMING 26

5.1 MINIMUM CLEARANCE TO COMBUSTIBLES 28

5.2 MINIMUM CLEARANCE TO COMBUSTIBLE ENCLOSURES 29

5.3 MINIMUM MANTEL CLEARANCES 31

6.0 FINISHING 32

6.1 DOOR REMOVAL / INSTALLATION 32

6.2 SHIPPING BRACKET 33

6.3 BOWL, MESH AND ROCK PLACEMENT 33

6.4 AFK82/RFK82 FACING KIT INSTALLATION 34

7.0 WIRING DIAGRAM / ELECTRICAL INFORMATION 35

7.1 ELECTRICAL CONNECTION 35

7.1.1 HARD WIRING CONNECTION 35

7.1.2 SCHEMATIC 35

8.0 OPERATION 36

8.1 GENERAL TRANSMITTER LAYOUT 36

8.2 APPLIANCE OPERATION 36

8.3 HAND HELD REMOTE OPERATIONS 36

8.4 TEMPERATURE DISPLAY 37

8.5 ROOM THERMOSTAT 37

8.6 SMART THERMOSTAT 37

8.7 FLAME HEIGHT 37

8.8 FAN SPEED 38

8.9 CHILD PROOF FUNCTION 38

8.10 REMOTE AUXILIARY OUTLET 38

8.11 LOW BATTERY / MANUAL BYPASS 39

8.12 IN THE EVENT OF A POWER FAILURE 39

8.13 FAN CONTROL MODULE 39

8.14 TIMED BLOWER 39

9.0 OPERATING INSTRUCTIONS 40

10.0 ADJUSTMENTS 41

10.1 RESTRICTING VERTICAL VENTS 41

10.2 PILOT BURNER ADJUSTMENT 41

10.3 VENTURI ADJUSTMENT 42

10.4 FLAME CHARACTERISTICS 42

11.0 MAINTENANCE 43

11.1 BOWL AND BURNER REMOVAL 43

11.2 DECORATIVE PANEL / BASE REMOVAL 44

11.3 SPARK MODULE BATTERY INSTALLATION 45

11.4 BLOWER REPLACEMENT 45

11.5 NIGHT LIGHT™ REPLACEMENT 46

11.6 GLASS / DOOR REPLACEMENT 46

11.7 CARE OF GLASS 47

11.8 CARE OF PLATED PARTS 47

12.0 REPLACEMENT PARTS 48

13.0 TROUBLE SHOOTING GUIDE 51

14.0 WARRANTY 54

15.0 SERVICE HISTORY 55

W415-0769 / A / 12.10.10

1.0 INSTALLATION OVERVIEW

See the section
“MINIMUM MANTEL
AND ENCLOSURE
CLEARANCES”

See the section
“FRAMING” and
“MINIMUM
MANTEL AND
ENCLOSURE
CLEARANCES”
for Drywall (or
other combustible
material)

See the section
“FRAMING” for
Non-combustible
material

3

See the section
“VENTING” and
“INSTALLATION”

See the section
“FRAMING”

See the section
“FRAMING”

Side
Wall

Rating plate, See “RATING
PLATE INFORMATION” section

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

W415-0769 / A / 12.10.10

4

2.0 INTRODUCTION

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES TO THIS APPLIANCE OR IT’S CONTROLS CAN BE DANGEROUS AND IS PROHIBITED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance
according to operating instructions could cause fi re or injury.

• Risk of fi re or asphyxiation do not operate appliance with fi xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be
sharp.

• Do not burn wood or other materials in this appliance.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or
clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep
toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other fl ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of traffi c and away from furniture and draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces.
These screens and guards must be fastened to the fl oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• The appliance is a vented gas-fi red appliance. Do not burn wood or other materials in the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance
and venting system are kept clean. The appliance and its venting system should be inspected before use and at least
annually by a qualifi ed service person. More frequent cleaning may be required due to excessive lint from carpeting,
bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other
fl ammable vapors and liquids.

• Under no circumstances should this appliance be modifi ed.

• This appliance must not be connected to a chimney fl ue pipe serving a separate solid fuel burning appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to inspect the
appliance and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done
by a licensed or qualifi ed service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust
fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these
openings can also cause the surrounding combustible materials to overheat and catch fi re.Only doors / optional fronts
certifi ed with the unit are to be installed on the appliance.

• Only doors / optional fronts certifi ed with the unit are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic
bags, these are not toys and should be kept away from children and infants.

• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as
having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated

temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a
T.V. or other electronic components.

• This appliance uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple supplied by
Wolf Steel Ltd.

!

WARNING

Toddlers,

3.1C

W415-0769 / A / 12.10.10

2.1 DIMENSIONS

37 5/8"

5"

46"

58"

5

17 3/4"

4" DIA.

7" DIA.

22 1/8"

21"

2"

7

/8"

13 7/8"

24"

28"

2.2 GENERAL INSTRUCTIONS

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT,

WITH THE GLASS DOOR OPENED OR REMOVED.

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” FROM THE

SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT

WHEN THE APPLIANCE IS OPERATING.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE

TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG.

8 7/8"

GAS INLET

!

WARNING

PROVIDE ADEQUA TE VENTILA TION.

FRONT FACE OF THE UNIT.

FIRE RISK. EXPLOSION HAZARD.

14"

28"

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.

USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING

COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.

THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to

conform with local codes. Installation practices vary from region to region and it is important to know the
specifi cs that apply to your area, for example in Massachusetts State:

• This product must be installed by a licensed plumber or gas fi tter when installed within the commonwealth
of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of a appliance
insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The fl exible connector must not be longer than 36 inches.

• A Carbon Monoxide detector is required in all rooms containing gas fi red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent
sealed combustion product.

W415-0769 / A / 12.10.10

6

A

A

The installation must conform with local codes or, in
absence of local codes, the National Gas and Propane
Installation Code CSA B149.1 in Canada, or the National
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United
States. Suitable for mobile home installation if installed in
accordance with the current standard CAN/CSA Z240MH
Series, for gas equipped mobile homes, in Canada or

NSI Z223.1 and NFPA 54 in the United States.

www.ncertied.org

s long as the required clearance to combustibles is
maintained, the most desirable and benefi cial location for an appliance is in the center of a building, thereby
allowing the most effi cient use of the heat created. The location of windows, doors and the traffi c fl ow in the
room where the appliance is to be located should be considered. If possible, you should choose a location
where the vent will pass through the house without cutting a fl oor or roof joist.

If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood
fl ooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.

Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must
be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian
Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.

We suggest that our gas
hearth products be installed
and serviced by professionals
who are certied in the U.S.
by the National Fireplace

®

Institute

(NFI) as NFI Gas

Specialists

4.1A

W415-0769 / A / 12.10.10

2.3 GENERAL INFORMATION

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEELMUST BE VENTED USING THE APPROPRIATE WOLF STEEL

GTS. SEE OWNERS INSTALLATION MANUAL FOR VENTING

SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARYSPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY

AFTER SERVICING THE VENT-AIR INTAKE SYSTAFTER SERVICING THE VENT-AIR INTAKE SYS

L'APPAREIL DOL'APPARE

D'EVACUD'EVAC

OU AUX ETATS-UNIS DE LA NORME DE SECURITE ET DE CONSTRUCTION DE MAISONS MANUFA

C

TCDV82PT

GD82

CDV82PT-TCDV82PT-T

H AIR FILTERS

S

/MBER /

:NO. DE SERIE:

FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND
QUALITY!

Altitude (FT) 0 - 4,500 0 - 4,500

Max. Input (BTU/HR) 26,000 26,000

Max. Output Steady State (BTU/HR) 16,150 16,150

Effi ciency (w/the fan on) 62% 62%

Min. Inlet Gas Supply Pressure 4.5” Water Column 11” Water Column

Max. Inlet Gas Supply Pressure 7” Water Column 13” Water Column

Manifold Pressure (Under Flow Conditions) 3.5” Water Column 10” Water Column

When the appliance is installed at elevations above 4,500ft, and in the absence of specifi c recommendations
from the local authority having jurisdiction, the certifi ed high altitude input rating shall be reduced at the rate of
4% for each additional 1,000ft.

This appliance is certifi ed to be installed in an aftermarket permanently located, manufactured (mobile) home,
where not prohibited by local codes.

7

APPLIANCE

NG LP

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certifi ed kit is used. No external electricity (110 volts or 24 volts)
is required for the gas system operation.

Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected.
Change in fl ame appearance from “HI” to “LO” is more evident in natural gas than in propane.

NOTE: The protective wrap on plated parts is best removed when the assembly is at room temperature
but this can be improved if the assembly is warmed, using a hair dryer or similar heat source.

2.4 RATING PLATE INFORMATION

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to
the model, venting and gas type of the appliance.

For rating plate location, see “INSTALLATION OVERVIEW” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

VENTED GAS FIREPLACE HEATER. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES,
IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES
AND COMMUNITIES, ANSI / NFPA 501A. FOYER DE CHAUFFAGE AU GAZ AVEC EVACUATION. HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE POUR INSTALLATION DANS UNE MAISON MOBILE SI SON INSTALLATION
CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU CANADA OU AUX ETATS-UNIS DE LA NORME DE SECURITE ET DE CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280. DANS LE
CAS OU CETTE NORME D'ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE REFERER A LA NORME RELATIVE AU CRITERE DE MESURES DE SECURITE CONTRE L'INCENDIEPOUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURES, LES SITES ET LES COMMUNAUTES, ANSI/NFPA 501A.

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA 2.33-2009, ANSI Z21.88-2009 VENTED GAS FIREPLACE HEATER / APPAREIL DE CHAUFFAGE ALIMENTE AU GAZ ET VENTILE

NATURAL PROPANE

GD82NT-T

CDV82NT

CDV82NT-T

PROPANE

GD82PT-T

GD82PT-T

CDV82PT

DV82P

CDV82PT-T

22 1/2”

THIS VENTED GAS FIREPLACE HEATER IS NOT FOR USE WITH AIR FILTERS

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEEL

VENT KITS. SEE OWNERS INSTALLATION MANUAL FOR VENTIN

VENT KITS. SEE OWNERS INSTALLATION MANUAL FOR VENTING

SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY

SERIAL NUMBER /

ERIAL NUMBER

AFTER SERVICING THE VENT-AIR INTAKE SYSTEM.

NO. DE SERIE:

NO. DE SERIE

L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L'ENSEMBLE
D'EVACUATION PROPRE A WOLF STEEL. REFERER AU MANUEL
D'INSTALLATION DE PROPRIETAIRE POUR L'EVACUATION PRECISE. IL EST
IMPORTANT DE BIEN REINSTALLER ET RESCELLER L'EVENT APRES AVOIR
ASSURE LE MAINTIEN DU SYSTEME DE PRISE D'AIR.

WOLF STEEL LTD.
24 Napoleon Rd. Barrie, Ontario L4M 4Y8 Canada

CE FOYER À GAZ VENTILÉS NE DOIT PAS ÊTRE UTILISÉ CONJOINTEMENT
AVEC DES FILTRES À AIR

W415-0769 / A / 12.10.10

W385-0348_G

22 1/2”

8

3.0 VENTING

RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.

IF VENTING IS INCLUDED WITH SPACERS THE VENT SYSTEM MUST BE SUPPORTED EVERY 3 FEET

FOR BOTH VERTICAL AND HORIZONTAL RUNS. USE SUPPORTS OR EQUIVALENT

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE REQUIRED CLEARANCE FROM

COMBUSTIBLES. USE WOLF STEEL LTD. SUPPORT RING ASSEMBLY W010-0370 OR EQUIVALENT

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE MINIMUM CLEARANCE TO COMBUSTIBLES

FOR BOTH VERTICAL AND HORIZONTAL RUNS. SPACERS ARE ATTACHED TO THE INNER PIPE AT

PREDETERMINED INTERVALS TO MAINTAIN AN EVEN AIR GAP TO THE OUTER PIPE. THIS GAP IS
REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED AT THE START, MIDDLE AND END OF

EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS MUST NOT BE REMOVED.

THIS APPLIANCE USES A 4” EXHAUST / 7” AIR INTAKE VENT PIPE SYSTEM.

For safe and proper operation of the appliance follow the venting instruction exactly. Deviation from the
minimum vertical vent length can create diffi culty in burner start-up and/or carboning. Under extreme vent
confi gurations, allow several minutes (5-15) for the fl ame to stabilize after ignition. Vent lengths that pass
through unheated spaces (attics, garages, crawl spaces) should be insulated with the insulation wrapped in
a protective sleeve to minimize condensation. Provide a means for visually checking the vent connection to
the appliance after the appliance is installed. Use a fi restop, vent pipe shield or attic insulation shield when
penetrating interior walls, fl oor or ceiling.

NOTE: If for any reason the vent air intake system is disassembled; reinstall per the instructions
provided for the initial installation.

!

WARNING

Refer to the section applicable to your installation.

7.1

W415-0769 / A / 12.10.10

3.1 VENTING LENGTHS AND COMPONENTS

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting
components. Minimum and maximum vent lengths, for both horizontal and vertical installations, and air terminal
locations for either system are set out in this manual and must be adhered to. For Simpson Dura-Vent, Selkirk Direct
Temp, American Metal Amerivent and Metal-Fab follow the installation procedure provided with the venting components.

A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

PART 4”/7” SUPPLIER WEBSITE

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SuperSeal 4DNA Metal-Fab www.mtlfab.com

For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the installation
procedure found on the website for your venting supplier.

For vent systems that provide seals on the inner exhaust fl ue, only the outer air intake joints must be sealed using a red
high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe
joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance fl ue collar which must
be sealed using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

9

When using Wolf Steel venting components, use only approved Wolf Steel rigid / fl exible components with the following

termination kits: wall terminal kit GD222R, or 1/12 to 7/12 pitch roof terminal kit GD110, 8/12 to 12/12 roof terminal kit
GD111, fl at roof terminal kit GD112 or periscope kit GD201 (for wall penetration below grade). With fl exible venting, in
conjunction with the various terminations, use either the 5 foot vent kit GD220 or the 10 foot vent kit GD330.

For optimum flame appearance and appliance performance, keep the vent length and number of elbows to a minimum.
The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that
it is unobstructed and undamaged.
Rigid and fl exible venting systems must not be combined. Different venting manufacturer components must not
be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20
feet. The maximum allowable vertical vent length is 40 feet. The maximum number of vent connections is two horizontally
or three vertically (excluding the appliance and the air terminal connections) when using fl exible venting.

Horizontal runs may have a 0” rise per foot however for optimum performance it is recommended that all horizontal
runs have a minimum 1” rise per foot using fl exible venting. For safe and proper operation of the appliance, follow the
venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family
dwellings and serves both dwellings. Local codes or regulations may require different clearances.
Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” air gap
all around between the inner liner and outer liner is required for safe operation.

8.7

W415-0769 / A / 12.10.10

10

3.2 TYPICAL VENT INSTALLATION

THE FIRST 2 FEET OF OUTER 7 “ DIAMETER VENT PIPE FROM THE APPLIANCE MUST BE WRAPPED

IN THE 1” THICK INSULATION SLEEVE (SUPPLIED). MAKE SURE THE INSULATION IS PULLED DOWN

TIGHT TO THE APPLIANCE WHEN INSTALLED. THERE AFTER, A 2” CLEARANCE ALL AROUND THE

VENT PIPE FROM COMBUSTIBLE MATERIALS ON ALL HORIZONTAL VENT SECTIONS IS REQUIRED.

!

WARNING

16” MINIMUM

3 FEET

* FIRST TWO

FEET

24” MAXIMUM

10” MINIMUM

56”

PLUS

RISE

46”

When venting, the horizontal run must be kept to a maximum of 20 feet. If a 20 foot horizontal run is required,
the appliance must have a minimum vertical rise immediately off the appliance of 57”. When terminating verti­cally, the vertical rise is a minimum 3 feet and a maximum 40 feet above the appliance.

REQUIRES

INSULATION

SLEEVE

46”

45.6

MINIMUM

40 FEET

MAXIMUM

W415-0769 / A / 12.10.10

3.3 SPECIAL VENT INSTALLATIONS

3.3.1 PERISCOPE TERMINATION

THE FIRST 2 FEET OF OUTER 7 “ DIAMETER VENT PIPE FROM THE APPLIANCE MUST BE
WRAPPED IN THE 1” THICK INSULATION SLEEVE (SUPPLIED). MAKE SURE THE INSULATION IS
PULLED DOWN TIGHT TO THE APPLIANCE WHEN INSTALLED. THERE AFTER, A 2” CLEARANCE

ALL AROUND THE VENT PIPE FROM COMBUSTIBLE MATERIALS ON ALL HORIZONTAL VENT

SECTIONS IS REQUIRED.

Use the periscope kit to locate the air termination above grade. The periscope
must be installed so that when fi nal grading is completed, the bottom air slot
is located a minimum 12” above grade. The maximum allowable vent length
(including both rise and run) is 10’.

!

WARNING

30” MINIMUM*

11

12”

MINIMUM

ABOVE
GRADE

* First two feet requires insulation sleeve

46”

9.3A

W415-0769 / A / 12.10.10

12

3.4 MINIMUM AIR TERMINAL LOCATION CLEARANCES

COVERED BALCONY APPLICATIONS

R

Q

M

G

P

Q

R

R

MIN

MAX

MAX

= 3 feet

= 2 x

Q

  feet

ACTUAL

INSTALLATIONS

CANADA U.S.A.
A 12” 12” Clearance above grade, veranda porch, deck or balcony.
B 12”

Δ

9”

Δ

Clearance to windows or doors that open.

C 12” * 12” * Clearance to permanently closed windows.

D 18” ** 18” **

Vertical clearance to ventilated soffi ts located above the terminal within a horizontal distance of 2’ from
the centerline of the terminal.

E 12” ** 12” ** Clearance to unventilated soffi t.
F 0” 0” Clearance to an outside corner wall.

0” *** 0” * ** Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

G

2” *** 2” *** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

H 3’ 3’ ****

Clearance to each side of the centerline extended above the meter / regulator assembly to a maximum
vertical distance of 15’.

I 3’ 3’ **** Clearance to a service regulator vent outlet.
J 12” 9” Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.
K 6’ 3’ Clearance to a mechanical air supply inlet.
L 7’ ‡ 7’ **** Clearance above a paved sidewalk or paved driveway located on public property.

M 12” †† 12” **** Clearance under a veranda, porch, deck or balcony.

N 16” 16” Clearance above the roof.
O 2’ †* 2’ †* Clearance from an adjacent wall including neighbouring buildings.
P 8’ 8’ Roof must be non-combustible without openings.
Q 3’ 3’ See chart for wider wall dimensions.

R 6’ 6’

The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

Δ

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to maximize the distance to vinyl clad soffi ts.

*** The periscope requires a minimum 18” clearance from an inside corner.

**** This is a recommended distance. For additional requirements check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the fl oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements check local codes.

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an open­ing between the terminal and the open side of the structure.

12.3B

W415-0769 / A / 12.10.10

3.5 VENTING APPLICATION FLOW CHART

TOP EXIT

13

Horizontal Termination

Vertical rise is equal

to or greater than

the horizontal run

Horizontal run +

vertical rise to

maximum of 40 feet

3.6 DEFINITIONS

For the following symbols used in the venting calculations and examples are:
> - greater than
> - equal to or greater than
< - less than
< - equal to or less than
HT - total of both horizontal vent lengths (Hr) and offsets (Ho) in feet
HR - combined horizontal vent lengths in feet
HO - offset factor: .03 (total degrees of offset - 90°*) in feet
VT - combined vertical vent lengths in feet

Vertical rise is less
than horizontal run

Horizontal run +

vertical rise to

maximum of 24.75

feet

4.2 times the

vertical rise equal to

or greater than the

horizontal run

Vertical Termination

Vertical rise is equal

to or greater than

the horizontal run

Horizontal run +

vertical rise to

maximum of 40 feet

Vertical rise is less
than horizontal run

Horizontal run +

vertical rise to

maximum of 40 feet

3 times the vertical

rise equal to or

greater than the

horizontal run

13.1

14.1

3.7 ELBOW VENT LENGTH VALUES

FEET INCHES

1° 0.03 0.5
15° 0.45 6.0
30° 0.9 11.0
45° 1.35 16.0
90°* 2.7 32.0

* The fi rst 90° offset has a zero value and is shown in the formula as - 90°

15.1

W415-0769 / A / 12.10.10

14

3.8 HORIZONTAL TERMINATION

(HT) < (VT)

Simple venting confi guration (only one 90° elbow)

See graph to determine the required vertical

rise VT for the required horizontal run HT.

40

39

30

REQUIRED

VERTICAL

20

RISE IN

FEET VT

10

0

2.5 5 7.5 10 12.5 15

HORIZONTAL VENT RUN PLUS OFFSET IN

FEET H

T

The shaded area within the lines represents

acceptable values for HT and V

For vent confi gurations requiring more than one 90° elbow, the following formulas apply:
Formula 1: HT < V

T

Formula 2: HT + VT < 40 feet

Example:
V

= 3 FT

1

V

= 8 FT

2

VT = V1 + V
H

= 2.5 FT

1

H

= 2 FT

2

HR = H1 + H
H

= .03 (three 90° elbows - 90°) = .03 (270° - 90°) = 5.4 FT

O

= HR + HO = 4.5 + 5.4 = 9.9 FT

H

T

HT + V

T

= 3 FT + 8 FT = 11 FT

2

= 2.5 + 2 = 4.5 FT

2

= 9.9 + 11 = 20.9 FT

90°

90°

90°

V

2

H

1

17.5 20

T

H

2

Formula 1: H

< V

T

T

9.9 < 11
Formula 2: HT + VT < 40 FT

20.9 < 40

Since both formulas are met, this vent confi guration is acceptable.

W415-0769 / A / 12.10.10

V

1

16.1A

15

V

V
V
V

(HT) > (VT)

Simple venting configuration (only one 90° elbow)

REQUIRED

See graph to determine the required vertical rise VT for the

required horizontal run H

150

147”

100

.

T

VERTICAL

RISE IN

INCHES V

T

57”

50

19 1/2”

0

515

2’

10

12.5’

19.5’

20

HORIZONTAL VENT RUN PLUS OFFSET IN FEET H

T

The shaded area within the lines represents acceptable

values for HT and VT

For vent configurations requiring more than one 90° elbow, the following formulas apply:

< 4.2 V

Formula 1:
Formula 2: HT + V

H

T

T

< 24.75 feet

T

90°

H

1

H

2

Example:

= VT = 6 FT

1

H

= 3 FT

1

H

= 5 FT

2

H

= H

+ H

R

H

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7 FT

O

H

= H

T

H

+ V

T

= 3 + 5 = 8 FT

1

2

+ H

= 8 + 2.7 = 10.7 FT

R

O

= 10.7 + 6 = 16.7 FT

T

V

1

90°

Formula 1: HT < 4.2 V

4.2 VT = 4.2 x 6 = 25.2 FT

10.7 < 25.2

Formula 2: HT + V

16.7 < 24.75

Since both formulas are met, this vent configuration is acceptable.

Example:

= 4 FT

1

= 1.5 FT

2

= V

+ V

T

H

= 2 FT

1

H

= 1 FT

2

H

= 1 FT

3

H

= 1.5 FT

4

H

= H

R

H

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT

O

H

= H

T

H

+ V

T

= 4 + 1.5 = 5.5 FT

1

2

+ H2 + H

1

+ H

R

= 13.6 + 5.5 = 19.1 FT

T

+ H4 = 2 + 1 + 1 + 1.5 = 5.5 FT

3

= 5.5 + 8.1 = 13.6 FT

O

Formula 1: HT < 4.2 V

4.2 VT = 4.2 x 5.5 = 23.1 FT

T

< 24.75 FT

T

T

90°

90°

90°

H

1

90°

V

1

V

2

H

H

2

3

H

4

13.6 < 23.1
Formula 2: HT + V

19.1 < 24.75

< 24.75 FT

T

Since both formulas are met, this vent configuration is acceptable.

16.1_2

W415-0769 / A / 12.10.10

16

3.9 VERTICAL TERMINATION

(HT) < (VT)

Simple venting configurations.

See graph to determine the required vertical rise V

required horizontal run H

40

30

REQUIRED

VERTICAL

20

RISE IN
FEET V

T

10

3

0

5101520

HORIZONTAL VENT RUN PLUS OFFSET IN FEET H

The shaded area within the lines represents acceptable

values for HT and VT

For vent configurations requiring one or more 90° elbows the following formulas apply:
Formula 1: H

Formula 2: HT + V

< V

T

T

< 40 feet

T

for the

.

T

T

T

Example:
V

= 5 FT

1

V

= 6 FT

2

V

= 10 FT

3

V

= V

+ V2 + V3 = 5 + 6 + 10 = 21 FT

T

1

H

= 8 FT

1

H

= 2.5 FT

2

H

= H

+ H

R

= .03 (four 90° elbows - 90°)

H

O

= .03 (360° - 90°) = 8.1 FT

H

= H

T

H

+ V

T

Formula 1: HT < V

18.6 < 21
Formula 2: HT + V

39.6 < 40

= 8 + 2.5 = 10.5 FT

1

2

+ H

= 10.5 + 8.1 = 18.6 FT

R

O

= 18.6 + 21 = 39.6 FT

T

T

T

< 40 FT

Since both formulas are met, this vent configuration is acceptable.

90°

V

3

90°

H

2

V

H

1

V

1

2

90°

90°

18.1

W415-0769 / A / 12.10.10

17

(HT) > (VT)

Simple venting configurations.

See graph to determine the required vertical rise V

required horizontal run H

20

19

REQUIRED

VERTICAL

RISE IN

FEET V

10

T

3

0

5101520

HORIZONTAL VENT RUN PLUS OFFSET IN FEET H
The shaded area within the lines represents acceptable

values for HT and VT

For vent configurations requiring more than two 90° elbows the following formulas apply:
Formula 1: H

Formula 2: HT + V

< 3V

T

T

< 40 feet

T

Example:
V

= 2 FT

1

V

= 1 FT

2

V

= 1.5 FT

3

V

= V

+ V2 + V3 = 2 + 1 + 1.5 = 4.5 FT

T

1

H

= 6 FT

1

H

= 2 FT

2

H

= H

+ H

R

H

= .03 (four 90° elbows - 90°)

O

= .03 (360° - 90°) = 8.1 FT

H

= H

T

H

+ V

T

= 6 + 2 = 8 FT

1

2

+ H

= 8 + 8.1 = 16.1 FT

R

O

= 16.1 + 4.5 = 20.6 FT

T

90°

H

V

1

1

90°

for the

.

T

H

V

2

T

25 30

V

2

3

90°

T

90°

Formula 1: HT < 3V
3VT = 3 x 4.5 = 13.5 FT

T

16.1 > 13.5
Since this formula is not met, this vent configuration is unacceptable.
Formula 2: HT + VT < 40 feet

20.6 < 40

Since only formula 2 is met, this vent configuration is unacceptable and a new fireplace location or vent configuration will
need to be established to satisfy both formulas.

18.1_2A

W415-0769 / A / 12.10.10