Napoleon Cinema, Cinema NEFB27H, Cinema NEFB29H, Cinema NEFB24H Installation And Operation Manual

NEFB24H / NEFB27H / NEFB29H

MULTIPLE PRODUCT CODES (LEAVE BLANK IF N/A)

ENGLISH

FRENCH

PG. 27

INSTALLATION AND

ADD MANUAL TITLE

OPERATION MANUAL

Cinema™ Insert Series

(MUST use title from Price Book)

(IF MULTIPLE, _____ ILLUSTRATED)

ADD PRODUCT IMAGE

Product Name / Code

NEFB24H Illustrated

SAFETY INFORMATION

!

WARNING

FIRE OR EXPLOSION HAZARD

If the information in these instructions are
not followed exactly, a fi re or explosion may
result causing property damage, personal
injury, or loss of life.

- Do not store or use gasoline or other
fl ammable vapors and liquids in the vicinity of
this or any other appliance.

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone [phone] • www.napoleon.com • [e-mail]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA /

INTERTEK

LOGO

ADD BUTTON BATTERY WARNING IF APPLICABLE

This appliance has a remote that requires button

batteries that are hazardous to young children.

FOR INDOOR USE ONLY

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

CSA 22.2 NO. 46 / UL 2021

CSA 22.2 NO. 46 / UL 1278

$10.00

W415-1454 / G / 04.01.19

EN

safety information

WARNING

!

• If equipped with a heater, this appliance can be hot when operated and can cause severe
burns if contacted.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fi re or injury.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• All electric appliances have hot and arcing or sparking parts inside. Do not use it in areas where a gas
line, paint or fl ammable liquids are present.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance
are kept clean. The appliance should be inspected before use and at least annually by a qualifi ed service
person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material,
etc. The appliance area must be kept clear and free from combustible materials, gasoline and other
fl ammable vapors and liquids.

• Under no circumstances should this appliance be modifi ed.

• Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to
inspect the appliance and to replace any part of the control system which has been under water.

• If equipped with a glass door, do not operate the appliance with the glass door removed, cracked or
broken. Replacement of the glass should be done by a licensed or qualifi ed service person. Do not strike
or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been
dropped or damaged in any manner. Return appliance to authorized service facility for examination,
electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• When installing this appliance in a room where water is present, the installation must comply with codes
recognizing the increased hazard of electrical shock and electrocution.

note:

Insert appropriate “Bathroom Warning (Electric)” (see 3-Warnings template folder).

This appliance is NOT suitable for installation in a bathroom.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord
away from traffi c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fi re, or damage the appliance.

2

• It is normal for your electric appliance to produce noise, especially when installed in a quiet space such
as a bedroom.

W415-1454 / G / 04.01.19

safety information

WARNING

!

• To prevent a possible fi re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like
a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable
power tap (outlet/power strip).

• These appliances are tested and listed for use only with the optional accessories listed in these instructions.

Use of optional accessories not specifi cally tested for this appliance could void the warranty and/or result in
a safety hazard.

For appliances equipped with a heater:

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before
servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install
an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and
away from hot surfaces.

• Clothing or other fl ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of traffi c and away from furniture and draperies.

EN

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is off, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from
hot surfaces. These screens and guards must be fastened to the fl oor.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or
damage to decorations, a TV or other electronic components.

!

WARNING:

compounds, which are known to the State of California to cause cancer, and chemicals includ­ing BBP and DEHP, which are known to the State of California to cause birth defects or other
reproductive harm. For more information, go to www.P65Warnings.ca.gov.

This product can expose you to chemicals including lead and lead

W415-1454 / G / 04.01.19

3

EN

table of contents

1.0 general information 5

1.1 dimensions 5

1.2 listing approvals 6

1.3 general instructions 6

1.4 rating plate information 7

1.5 label location 7

2.0 locating appliance 8

2.1 unpacking and testing appliance 8

2.2 grounding the appliance 8

3.0 installation 9

3.1 minimum clearance to combustibles 9

3.2 minimum mantel clearances 9

3.3 framing 10

3.3.1 hard-wiring installation 11

3.3.2 appliance installation 12

4.0 operating instructions 13

4.1 operating control panel 13

4.2 operating by remote control 14

4.3 remote control battery installation 15

5.0 finishing 16

5.1 glass door removal and installation 16

5.2 log, grate, and ember bed assembly removal 16

5.3 brick panel installation and removal (NEFB29H only) 17

6.0 electrical information 18

6.1 wiring diagram 18

7.0 replacement parts 19

7.1 NEFB24H overview 20

7.2 NEFB27H overview 21

7.3 NEFB29H overview 22

8.0 troubleshooting 23

9.0 warranty 25

4

note:

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves
the right to change or modify any information within this manual at any time without notice. Changes, other than
editorial, are denoted by a vertical line in the margin.

W415-1454 / G / 04.01.19

1.1 dimensions

24"

610mm

1.0 general information

EN

533mm

14 5/8"
371mm

CEFB24H ILLUSTRATED

NEFB24H Illustrated

15 3/4"

399mm

CEFB27H ILLUSTRATED

NEFB27H Illustrated

21"

27"

24"

686mm

610mm

17 5/8"
448mm

11 5/8"

294mm

12 3/4"
323mm

18 5/8"

473mm

8 5/8"

9 1/2"

219mm

241mm

17"

432mm

18"

457mm

22 1/8"

25 1/8"

563mm

639mm

737mm

29"

17 1/4"

437mm

NEFB29H Illustrated

CEFB29H ILLUSTRATED

26"

660mm

20 1/8"
511mm

14 1/4"
361mm

9 1/2"

241mm

19 1/2"

495mm

27 1/4"

691mm

510mm

20 1/8"

W415-1454 / G / 04.01.19

5

EN

general information

1.2 listing approvals

This appliance has been tested in accordance with the CSA Standards for fi xed and location-dedicated electric
room appliances in the United States and Canada. If you need assistance during installation, please contact your
local dealer.

note:

This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local
codes, with the latest edition of the National Electrical Code ANSI/NFPA 70 in the United States or the Canadian
Electrical Code CSA C22.1 in Canada.

Model Number

Description

Voltage

Watts

Amps

Appliance Width

Appliance Height

Appliance Depth

Net Weight

Gross Weight (1A)

Gross Weight (3A)

NEFB24H NEFB27H NEFB29H

24" Electric

Appliance

Dedicated 15 AMP Grounded Circuit

24" (610mm) 27" (686mm) 29" (737m)

17 5/8"

(448mm)

8 5/8" (219mm) 9 1/2" (241mm) 9 1/2" (241mm)

29.1lbs (13.2kg) 33.6lbs (15.3kg) 33.7lbs (15.3kg)

33.1lbs (15kg) 37lbs (17.1kg) 38.5lbs (17.5kg)

35.1 lbs (16kg) 40.9lbs (18.6kg) 41.8lbs (19kg)

27" Electric

Appliance

120V AC

Max 1500W

18 5/8"

(473mm)

29" Electric

Appliance

20 1/8"

(511mm)

1.3 general instructions

• Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the outlet
are on.

• The appliance may emit a slight, harmless odour when fi rst used. This odour is normal and it is caused by
the initial heating of internal appliance elements and will not occur again.

• If your appliance does not emit heat when called for, consult the “operation” section of this manual for further
information.

• Use with a CSA or UL certifi ed surge protector.

• Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured
homes when installed according to these instructions.

As with most electronic devices, your new electric appliance has been designed to operate at temperatures
between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the appliance to reach room
temperature before turning it on.

6

W415-1454 / G / 04.01.19

1.4 rating plate information

SAMPLE

M

UNE SALLE DE BAIN ELLE DE BAIN

APPROPRIE POUR INSTALLATIONAPPROPRIE POUR INSTAL

MAISO

MAISON MO

V

VOLTAGE:

C120 VAC

TENSION:TENS

:FREQUENCY:

60Hz 60Hz

MODEL / MODÈLE:

HNEF

MASTER CONTRACT: 161746 CONTRACT: 16174

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 2021 /

HOMOLOGUÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 2021

general information

EN

ELECTRIC FIREPLACE. SUITABLE FOR
BEDROOM AND BED-SITTING ROOM
INSTALLATION. SUITABLE FOR MOBILE
HOME INSTALLATION.

WOLF STEEL LTD.

24 NAPOLEON ROAD,
BARRIE, ON, L4M 0G8 CANADA

For rating plate location, see “label location” section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

MASTER CONTRACT: 161746

MODEL / MODÈLE:

MODEL / MODÈLE:

VOLTAGE: 120 VAC TENSION: 120VCA

OLTAGE:

FREQUENCY

FREQUENCY: 60Hz FRÉQUENCE: 60Hz

POWER: 1500W PUISSANCE: 1500W

DATE CODE: XXXXX CODE DE DATE:

DESIGNED IN NORTH AMERICA

BY WOLF STEEL LTD.

MADE IN CHINA FABRIQUÉ EN CHINE

note:

The rating plate must remain with the appliance at all times. It must not be removed.

120 VA

SERIAL NUMBER/NO. DE SERIE:

FOYER À ÉLECTRIQUE. HOMOLOGUÉ POUR
INSTALLATION DANS UNE CHAMBRE À
COUCHER, UNE SALLE DE BAIN ET UN STUDIO.
APPROPRIE POUR INSTALLATION DANS UNE
MAISON MOBILE.

N MOBILE.

CONTRAT-CADRE: 161746

CONTRAT-CADRE: 161746

NEFB24H

NEFB24

DÉSIGNÉ AMÉRIQUE DU
NORD PAR WOLF STEEL LTD.

NEFB

1.5 label location

W385-2062 / A

F

G

A
B
C

D

Back View of Appliance

Ref. Part Number Label Description

A

B

C

D

E

F

G

H

I

W385-2017 * " Hot Surface"

W385-1946 * "Do Not Cover"

W385-2133 * "Attention"

W385-1943 "Warning"

W385-2003 ** Hard-Wiring

W385-2062 Rating Plate (NEFB24H)

W385-2061 Rating Plate (NEFB27H)

W385-2002 Rating Plate (NEFB29H)

W385-1944 "Warning"

W385-1945 "Caution"

W385-2009 Wiring Diagram

H

I

E

* Situated on the front
of the appliance.

** Situated on the side
of the appliance.

W415-1454 / G / 04.01.19

7

EN

2.0 locating appliance

WARNING

!

• Due to high temperatures, this electric appliance should be located out of traffi c. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes, and curtains at least 36" (91.4cm) from the front of the
appliance.

• Never locate this electric appliance where it may fall into a bathtub or other water container.

• Wear safety gloves and safety glasses for protection during installation and maintenance.

• To prevent contact with sagging or loose insulation, the electric appliance must not be installed against vapour
barrier or exposed insulation. Localized overheating could occur and a fi re could result.

• Do not expose the electric appliance to the elements (i.e. rain, snow, etc.).

2.1 unpacking and testing appliance

Carefully remove the appliance from the box and remove the support brackets. Prior to installing the appliance,
remove all packaging material and test to make sure the appliance operates properly by plugging the power
supply cord into a conveniently located 120V,15 Amp minimum grounded outlet.

2.2 grounding the appliance

This appliance is for use on 120 volts. The cord has a plug as shown in (A). An adapter as shown in (C) is available
for connecting three-blade grounding type plugs to two-slot receptacles, as shown in (B).
The green grounding plug extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove plug from outlet.

Grounding Methods

Not allowed in Canada

Metal Screw

Cover of

grounded

(A)

note:

Must be connected to a dedicated 15 amp circuit. The use of an extension cord is NOT permitted.

outlet box

Grounding Pin

(B)

(C)

Adapter

Grounding Means

8

W415-1454 / G / 04.01.19

3.0 installation

WARNING

!

• Risk of fi re! The power cord must not be pinched against a sharp edge. Secure cord to avoid tripping or
snagging to reduce the risk of fi re, electric shock, or personal injury. Do not run cord under carpeting. Do not
cover cord with throw rugs, runners, or similar items. Arrange cord away from traffi c areas and where it will not
be tripped over.

• Risk of fi re! To prevent a possible fi re, do not block air intake or exhaust in any manner. Do not use on soft
surfaces where openings may become blocked.

• Risk of fi re! Do not blow or place insulation against the appliance.

• This electric appliance is tested and listed for use only with the approved optional accessories. Use of optional
accessories not specifi cally tested for this electric appliance could void the warranty and/or result in a safety
hazard.

• If the information in these instructions is not followed exactly, a fi re or explosion may result causing property
damage, personal injury, or death. Do not store or use gasoline or other fl ammable vapors in the vicinity of this
or any other appliance.

• This appliance is heavy. It is highly recommended that two people install this appliance.

• If your appliance is equipped with a heater, ensure the heater vents cannot, in any way, be covered as it may
create a fi re hazard.

• Do not run the power cord horizontally, directly below the appliance.

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture, and high traffi c
areas.

note:

Follow all national and local electrical codes.

EN

3.1 minimum clearance to combustibles

Measurements are taken from the glass front.

Bottom 0" Top 0" to 2" (51mm) mantel
Sides 1/4" (6mm) Top 3" (76mm) to ceiling
Back 1/4" (6mm) Top 1/4" (6mm) to enclosure

note:

The control panel switch is located on the upper right hand side of the appliance. Always ensure this switch
remains accessible.

3.2 minimum mantel clearances

WARNING

!

• When using paint or lacquer to fi nish the mantel, the paint or lacquer must be heat resistant to prevent
discoloration.

3"

76mm

2"

51mm

1"

25mm

8"8"

6"

MANTEL

203mm

152mm

102mm

4"

51mm

2"

1/4"

6.3mm

TOP OF APPLIANCE

W415-1454 / G / 04.01.19

9

EN

installation

3.3 framing

Prepare rough in framing following the recommended dimensions in Figure 1. For the corner rough in framing,
follow the recommended dimension in Figure 2.

Select a location that is not prone to moisture and is located at least 36" (91.4cm) away from combustible
materials such as curtain drapes, furniture, bedding, paper etc.

Fig. 1

Fig. 2

K

B

FLOOR

(Or mantel base thickness)

F

A

Rough Framing

A. Once the rough opening has been prepared, and the power has been routed to the right side of the

recess, the appliance may be installed.

B. The electrical connection must be made prior to placing the appliance into position (see "hard-wiring

installation" section).

B

C

Rough Framing in a Corner

J

L

10

W415-1454 / G / 04.01.19

NEFB24H NEFB27H NEFB29H

A

(229mm)

B

(58.4cm)

17 1/4"

C

(43.8cm) + F

J

(104.1cm)

K

(73.6cm)

9"

23"

41"

29"

10"

(254mm)

26"

(66cm)

18 1/4"

(46.3cm) + F

44"

(111.8cm)

31 1/2"

(80cm)

10"

(254mm)

28"

(71.1cm)

19 3/4"

(50.2cm) + F

46"

(116.8cm)

32 1/2"

(82.6cm)

installation

GREEN

BLACK

WHITE

3.3.1 hard-wiring installation

WARNING

!

• Turn off the appliance completely and let cool before servicing. Only a qualifi ed service person should service
and repair this electric appliance.

HARD-WIRING CONNECTION

If it is necessary to hard-wire this appliance, a qualifi ed electrician must remove the cord connection and wire the
appliance directly to the household wiring. The wire and power supply breaker must rated for 120V minimum 15
Amps.

This appliance must be electrically connected and grounded in accordance with local codes, if hard-wired. In the
absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the current
ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

note:

There are 3 wires from the appliance junction: white (neutral), black (power L1), and green (ground) that connect
to 120V power suply (breaker panel). See below for details.

White, Green and

Black wires:

Connect to 120V

power supply.

EN

WHITE

BLACK

NEFB24H

Illustrated

GREEN

A. Remove the securing screw from the electrical cover plate, located on the right hand side of the

appliance.

B. Add an electrical box connector and feed the supply wires through the 7/8" (22mm) hole.
C. Separate the black, white, and green wires that have the wire nuts on them.
D. Remove the wire nuts and secure the black wire (power L1) to the black (power L1) lead of the power

supply. Connect the white wire from the appliance to the white (neutral) wire from the power supply.
Connect the green wire to the ground wire.

E. Resecure the cover plate.

'

+

*

6

3

/

&

$

1

5

­*

"

0

$

/

&

BLACK

WHITE

GREEN

(L1)

(N)

(G)

WIRE NUT

BLACK

WHITE

GREEN

4

1

6

0

1

8

1

&

-

3

:

W415-1454 / G / 04.01.19

11

EN

installation

3.3.2 appliance installation

note:

This appliance is equipped with nylon pads located on the bottom four corners. To prevent damaging the base
of the mantel, carefully lift the appliance into the mantel while avoiding contact from the front edge of the mantel
base.

A. With two people, lift the appliance up and insert into the opening, keeping a 3/8" (10mm) space between

the appliance and fl oor base in order to not scratch the fl oor surface. Do not push or slide the bottom of
the appliance on the fl oor base (Fig. 1).

B. Set the appliance down and into place (Fig. 2).
C. If the appliance does not sit fl at on the fl oor or mantel base, apply a shim (not supplied) under the nylon

pads and adjust until level.

Fig. 1

ÉTAPES 1: SOULEVER

APPLIANCE

APPAREIL

STEP 1: LIFT

1/4"

MANTEL

MANTEL

TABLETTE

STEP 2: INSERT

ÉTAPES 2: INSÉREZ

DO NOT SLIDE APPLIANCE

NE GLISSEZ PAS L'APPAREIL

Fig. 2

MANTEL

MANTEL

TABLETTE

APPLIANCE

APPAREIL

STEP 3: SET APPLIANCE

ÉTAPES 3: RÉGLÉ APPAREIL

!!

12

W415-1454 / G / 04.01.19

4.0 operating instructions

WARNING

!

• Ensure the house circuit breakers for the power supply are turned on. When initially connecting the appliance
into a power source, the appliance will perform an LED check. The appliance will fl ash on and off for 5 seconds.

Once the appliance has been plugged into a grounded electrical outlet or hard-wired to a dedicated 120V power
supply, it is ready to operate.

4.1 operating control panel

The Control Panel is located on the top front of the appliance.

EN

Power

Flame & Ember

Light Control

Heater

Control

Timer

Decorative Light

(NEFB27H &

NEFB29H only)

Turns the appliance on / off.

Controls fl ame brightness and ember light.

5 Settings: Flame & ember off (F0), ember on but fl ame off
(LL), small fl ame & ember (F1), medium fl ame & ember (F2),
brightest fl ame & ember (F3).

Turns the heater and blower on / off.

4 Settings: Heater & blower off (HO), blower on (BL), low
heat (H1), high heat (H2).

Timer can be programmed to run appliance for specifi c
lengths of time (30mins. minimum to 6hrs. maximum).

Controls decorative light settings.

4 Settings: Decorative light off (do), white colour (d1),
auto-cycle from white / orange / blue / orange-blue / white­orange / white-blue (d2), lock to desired colour (d3).

NOTE: It will take 8.5 seconds to switch between on d2
setting.

F° / C°

Switch

Heater

Lock

Temperature

Control

Control temperature format (Fahrenheit or Celsius).

Press and hold the fl ame button for 5 seconds.

Heater button can be locked or unlocked by holding the
heater button for 5 seconds.

Press and hold the timer button for 5 seconds. This will
change the buttom to Temperature Control, or vice versa.

7 Settings: 16°C (61°F), 18°C (64°F), 21°C (70°F), 24°C
(75°F), 27°C (81°F), 29°C (85°F) and OFF.

W415-1454 / G / 04.01.19

13

EN

operating instructions

4.2 operating by remote control

WARNING

!

• To avoid danger of suffocation, keep the packaging bag away from babies and children. Do not use in cribs,
beds, carriages, or play pens. This bag is not a toy. Knot before throwing away.

note:

When operating the remote control, it must be directed towards the front centre of the appliance. This remote
control must remain within 6 meters (20 feet) of the appliance to be effective.

Power

Flame & Ember

Light Control

Thermostat

Heater &

Blower

Turns the appliance on / off.

Controls fl ame brightness and ember light.

5 Settings: Flame & ember off (F0), ember on
but fl ame off (LL), small fl ame & ember (F1),
medium fl ame & ember (F2), brightest fl ame &
ember (F3).

Controls the thermostat.

7 Settings: 16°C (61°F), 18°C (64°F), 21°C
(70°F), 24°C (75°F), 27°C (81°F), 29°C (85°F)
and OFF.

NOTE: When the room temperature is 2 de­grees lower than the temperature setting, the
heater will turn on.

Controls the heater and blower.

4 Settings: Heater & blower off (HO), blower
on (BL), low heat (H1), high heat (H2).

14

Timer

Decorative Light

(NEFB27H &

NEFB29H only)

W415-1454 / G / 04.01.19

Timer can be programmed to run appliance for
specifi c lengths of time (30mins. minimum to
6hrs. maximum).

Controls decorative light settings.

4 Settings: Decorative light off (d0), white
colour (d1), auto-cycle from white / orange /
blue / orange-blue / white-orange / white-blue /
(d2), lock to desired colour (d3).

NOTE: It will take 8.5 seconds to switch be­tween on d2 setting.

NEFB27H & NEFB29H

Remote Control Illustrated

operating instructions

4.3 remote control battery installation

WARNING

!

• This remote control requires button batteries that are hazardous to young children.

• WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN.

• Swallowing may lead to serious injury or death in as little as 2 hours due to chemical
burns and potential perforation to the oesophagus.

• If you suspect your child has swallowed or inserted a button battery, immediately
seek urgent medical assistance.

• Examine devices and make sure the battery compartment is correctly secured (i.e.
that the screw or other mechanical fastener is tightened). Do not use if compartment is not secure.

• Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.

• Tell others about the risks associated with button batteries and how to keep their children safe.

EN

1. To replace the existing battery, remove the battery
holder.

2. To remove the battery holder, turn the remote onto its
front side. Slide the battery holder outwards.

3. Replace the existing battery holder with a new battery
(type CR 2025). Slide the battery holder back into
position.

4. The battery holder is secure onto the remote control
when a "CLICKING" noise is heard.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be
recycled, and may be accepted for disposal at your local recycling center. Check with your
municipality for recycling instructions.

Remote

Control

(Rear Side)

Battery (CR 2025)

Battery Holder

W415-1454 / G / 04.01.19

15

EN

5.0 fi nishing

WARNING

!

• Power supply service must be completed prior to fi nishing to avoid reconstruction.

• Heat vents and air openings cannot be covered under any circumstances.

5.1 glass door removal and installation

WARNING

!

• Facing and/or fi nishing materials must not interfere with air fl ow through air openings, louvre openings, operation
of louvres or doors, or access for service. Observe all clearances when applying combustible materials.

• Before door is removed, turn the appliance off and wait until appliance is cool to the touch. Doors are heavy and
fragile so handle with care.

A. Remove the 4 screws off the appliance (Fig. 5-1).
B. Remove the glass front and place on a soft non-abrasive

surface.

C. Reverse these steps to reinstall the glass front.

SCREW

Fig. 5-1

5.2 log, grate, and ember bed assembly removal

For Model NEFB24H and NEFB27H:

A. Remove the 4 screws securing the ember bed to the sides (and bottom, if applicable) of the appliance

(Fig. 5-2).

note:

Some models only have two screws.

B. Lift the log, grate and ember bed up from the appliance and remove.

For Model NEFB29H:

A. Remove the packaging materials holding the logs, grate and ember bed assembly to the appliance.
B. Pinch the back of the assembly and lift it up from the appliance.

Screw

Screw

(if applicable)

Screw

Screw

(if applicable)

16

NEFB27H Illustrated

Fig. 5-2

W415-1454 / G / 04.01.19