Napoleon Bayfield GDS25N-1, Bayfield GDS25P-1 Installation And Operation Manual

NATURAL GAS MODELS:

GDS25N-1

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

ENGLISH

PROPANE GAS MODELS:

SAFETY INFORMATION

!

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

GDS25P-1

FRENCH

PG. 51

INSTALLATION AND

ADD MANUAL TITLE

OPERATION MANUAL

PRODUCT NAME™

SAFETY BARRIER

ADD PRODUCT IMAGE

Bayﬁeld™

ADD ____ ILLUSTRATED

- Installation and service must be

performed by a qualiﬁ ed installer, service agency, or the supplier.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleonﬁ replaces.com • hearth@napoleonproducts.com

FOR INDOOR USE ONLY

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

CSA /

INTERTEK

LOGO

$10.00

W415-2207 / B / 02.05.18

• Under no circumstances should this appliance be modiﬁ ed.

DANGER

!

WARNING

EN

safety information

• This appliance is hot when operated and can cause severe burns if contacted.

• Any changes or alterations to this appliance or its controls can be dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure to operate appliance according to operating instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed

when lighting the pilot for the ﬁ rst time and when the gas supply has run out.

• Risk of ﬁ re or asphyxiation do not operate

appliance with ﬁ xed glass removed and never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 4 feet (1.22m) from the front face of the appliance.

• Do not connect 110 volts to the control valve,

with the exception of models; GSST8 and GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing

and operating the appliance. Never obstruct the front opening of the appliance.

• The appliance area must be kept clear and free from combustible materials, gasoline and other

ﬂ ammable vapors and liquids.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from

furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior

to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it

serviced. Keep burner and control compartment clean.

!

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

2

W415-2207 / B / 02.05.18

• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance and venting system are kept clean. The appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

!

WARNING

!

WARNING

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame patterns.

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these openings can also cause the surrounding combustible materials to overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people; pregnant women, persons with heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide.(Not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V. or other electronic components.

• For appliances equipped with a safety barrier; the barrier is designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed. If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

• For outdoor products only: this appliance must not be installed indoors or within any structure that prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple supplied by Wolf Steel Ltd.

safety information

EN

!

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

!

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

W415-2207 / B / 02.05.18

3

EN

table of contents

1.0 general information 5

1.1 rates and efﬁciencies 5

1.2 installation overview 6

1.3 rating plate information 8

1.4 mobile home installation 8

1.5 hardware list 9

1.6 dimensions 10

2.0 venting requirements 11

2.1 typical venting installation 13

2.2 special vent installations 14

2.2.1 periscope termination 14

2.2.2 corner termination 14

2.3 vent terminal clearances 15

2.4 horizontal termination 16

2.5 vertical termination 17

2.6 vertical through existing chimney 18

3.0 installation 19

3.1 horizontal installation 20

3.2 vertical installation 20

3.3 horizontal air terminal installation 21

3.4 extended horizontal and corner air terminal

installation 21

3.5 vertical air terminal Installation 22

3.6 appliance vent connection 23

3.7 gas installation 23

3.8 minimum clearance to combustibles 24

3.9 minimum mantel or shelf clearances 25

4.0 finishing 26

4.1 cast front installation and removal 26

4.2 safety barrier installation and removal 26

4.3 glass door installation and removal 27

4.4 log placement 27

4.5 logo placement 28

5.0 optional blower installation 29

6.0 wiring diagram 31

7.0 operation 32

7.1 general transmitter layout 33

7.2 initializing the transmitter / battery holder

for the ﬁrst time 33

7.3 temperature display 34

7.4 ﬂame height 34

7.5 blower speed 34

7.6 night light dimmer control 34

7.7 continuous pilot / intermittent pilot (CPI / IPI) selection 34

7.8 key lock 35

7.9 low battery / manual bypass 35

8.0 adjustment 36

8.1 restricting vertical vents 36

8.2 venturi adjustment 36

8.3 pilot burner adjustment 36

8.4 ﬂame characteristics 37

9.0 maintenance 38

9.1 annual maintenance 39

9.2 night light replacement 40

9.3 pilot injector and oriﬁce replacement 40

9.4 care of glass 41

9.5 care of plated parts 41

10.0 replacements 42

10.1 overview 43

10.2 valve train assembly 44

11.0 accessories 45

12.0 troubleshooting 46

13.0 warranty 49

4

note:

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves the right to change or modify any information within this manual at any time without notice. Changes, other than editorial, are denoted by a vertical line in the margin.

The camera icon indicates video tutorials are available as additional reference, visit http://www.napoleonﬁreplaces.com/category/product-support/support-centre/

W415-2207 / B / 02.05.18

Installer, please ﬁll out the following information:

Customer: Address: Date of Installation: Location of appliance: Installer: Dealer/Distributor contact number: Serial #:

Model:

standard checklist

EN

Natural Gas: GDS25N-1

Propane: GDS25P-1

1.0 general information

For elevations between 2,000ft (610m) and 4,500ft (1372m) above sea level, this appliance must be de-rated by 10% using the certiﬁed high altitude kit. When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speciﬁc recommendations from the local authority having jurisdiction, the certiﬁed high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft (305m).

Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

This appliance is approved for closet or recessed installations, as well as for bathroom, bedroom and bed-sitting room installations and is suitable for mobile home installations. The natural gas model can be installed in a mobile home that is permanently positioned on its site and fueled with natural gas.

note:

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance and must be installed.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat source.

This appliance is a decorative product. It is not a source of heat and not intended to burn solid fuel.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be recycled, and may be accepted for disposal at your local recycling center. Check with your municipality for recycling instructions.

1.1 rates and efﬁciencies

Altitude (FT) 0-2,000 0-2,000 Max. Input (BTU/HR) 24,500 23,000

Max. Output (BTU/HR) 19,000 16,000 Efﬁciency (w/the fan on) 80% 80% Min. Inlet Gas Supply Pressure 4.5" Water Column (11mb) 11" Water Column (27mb) Max. Inlet Gas Supply Pressure 13" Water Column (17mb) 13" Water Column (32mb) Manifold Pressure (Under Flow Conditions) 3.5" Water Column (9mb) 10" Water Column (25mb)

GDS25-1

NG P

W415-2207 / B / 02.05.18

5

EN

general information

1.2 installation overview

78

6

5

2

1

3

4

6

SAFETY BARRIER

Recommended installation steps:

1. Determine venting requirements before deciding the ﬁnal location of the appliance.

2. Place the appliance in its ﬁnal position.

3. Create hole for appliance venting.

4. Install appliance venting (refer to “venting requirements” and “installation” sections).

5. Install all electrical wirings (refer to “wiring diagram” section).

6. Install gas lines (refer to “gas installation” section).

7. Complete ﬁnishing (refer to “ﬁnishing” section).

8. Test appliance (refer to “gas installation” section).

W415-2207 / B / 02.05.18

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

general information

WARNING

!

• Always light the pilot whether for the ﬁrst time or if the gas supply has run out, with the glass door opened or removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of the appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when appliance is operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test pressures above 1/2 PISG (35mb). Close the manual shut-off valve before pressure testing gas line at test pressures equal to or less than 1/2 PISG (35mb).

• Use only Wolf Steel approved optional accessories and replacement parts with this appliance using nonlisted accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result in a safety hazard and will void the warranty and certiﬁcation.

• The appliance must not be operated at temperatures below freezing (32ºF/0ºC). Allow the appliance to warm to above freezing prior to operation.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for example in Massachusetts State:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.

The installation must conform with local codes or, in absence of local codes, the National Gas and Propane Installation Code CSA B149.1 in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States. Suitable for mobile home installation if installed in accordance with the current standard CAN/CSA Z240MH Series, for gas equipped mobile homes, in Canada or ANSI Z223.1 and NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (35 mb). The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

www.ncertied.org

We suggest that our gas hearth products be installed and serviced by professionals who are certied in the U.S. by the National Fireplace

®

Institute

(NFI) as NFI Gas

Specialists

EN

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

W415-2207 / B / 02.05.18

7

SAMPLE

EN

general information

1.3 rating plate information

CONFORMS TO / CONFORME AUX: ANSI Z21.50-2016, CERTIFIED TO / CERTIFIE CSA 2.22-2016 VENTED DECORATIVE GAS APPLIANCE / FOYER À GAZ VENTILÉ.

APPROVED FOR BEDROOM, BATHROOM & BEDSITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A. FOR

USE WITH BARRIER W010-3295. FOLLOW THE INSTALLATION INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL

9700539 (WSL) 4001657 (NGZ)

MANIFOLD PRESSURE: 3.5” W.C. (NG)

4001658 (NAC) 4001659 (WUSA)

PRESSION AU COLLECTEUR: 3.5" D'UNE

COLONNE D'EAU(GN) MIN SUPPLY PRESSURE: 4.5" W.C.(NG)

0-2000ft 2000-4500ft ALTITUDE / ELEVATION 0-2000ft 2000-4500ft

PRESSION D'ALIMENTATION MIN: 4.5" D'UNE COLONNE D'EAU (GN)

24,500 BTU/h 22,000 BTU/h INPUT / ALIMENTATION 23,000 BTU/h 20,000 BTU/h

MAX. SUPPLY PRESSURE: 7" W.C. (NG)

19,000 BTU/h 16,000 BTU/h REDUCED INPUT / 16,000 BTU/h 14,000 BTU/h

PRESSION D'ALIMENTATION MAX: 7"

ALIMENTATION REDUITE

D'UNE COLONNE D'EAU (GN) AFUE: 64%

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS UNIT ONLY. WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE. ELECTRICAL RATING: 115V 1.5AMP 60HZ THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS. SEE OWNERS INSTALLATION MANUAL FOR VENTING SPECIFICS. MINIMUM AND MAXIMUM VERTICAL VENT LENGTHS ARE 3 FEET AND 40 FEET RESPECTIVELY.

WOLF STEEL LTD. 24 NAPOLEON ROAD, BARRIE. ONTARIO L4M 0G8 CANADA

NOT FOR USE WITH SOLID FUEL

MINIMUM AND MAXIMUM HORIZONTAL VENT LENGTHS ARE 10 INCHES AND 20 FEET RESPECTIVELY. PROPER REINSTALLATION AND RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR INTAKE SYSTEM.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIAL:

A 4" B 2" C 2"

VENT TOP 2" TO CEILING FROM VENT BOTTOM 1" STOVE TOP 48” VENT SIDES 1"

GDS25N

MODEL

HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE POUR INSTALLATION DANS UNE MAISON MOBILE SI SON

INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU CANADA OU AUX ETATS-UNIS DE LA NORME DE SECURITE ET DE CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE REFERER A LA NORME RELATIVE AU CRITERE DE MESURES DE SECURITE CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURES, LES SITES ET LES COMMUNAUTES, ANSI/NFPA 501A. POUR UNE

UTILISER AVEC BARRIÈRE W010-3295. SUIVEZ LES INSTRUCTIONS D'INSTALLATION

GDS25P

UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILSE AVEC CET APPAREIL

UTILISER AVEC LES PORTES VITREES HOMOLOGUEES SEULEMENT AVEC CETTE UNITE. AVERTISSEMENT: N'AJOUTEZ PAS A CET APPAREIL AUCUN MATERIAU DEVANT ENTRER EN CONTACT AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT. CLASS.: 115V 1.5AMP 60HZ L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L'ENSEMBLE D'EVACUATION PROPRE A WOLF STEEL. REFERER AU MANUEL D'INSTALLATION DE PROPRIETAIRE POUR L'EVACUATION PRECISE. LES LONGUEURS VERTICALES MINIMALES ET MAXIMALES SONT3 PIEDS ET 40 PIEDS RESPECTIVEMENT.

SERIAL NUMBER / NO. DESERIE

SE TROUVENT DANS LE MANUEL D'INSTALLATION.

GDS25

MANIFOLD PRESSURE: 10” W.C. (LP)

PRESSION AU COLLECTEUR: 10" D'UNE

MIN SUPPLY PRESSURE: 11" W.C.(LP)

PRESSION D'ALIMENTATION MIN: 11"

D'UNE COLONNE D'EAU (P)

MAX. SUPPLY PRESSURE: 13" W.C. (LP)

PRESSION D'ALIMENTATION MAX: 13"

D'UNE COLONNE D'EAU (P)

LES LONGUEURS HORIZONTALES MINIMALES ET MAXIMALES SONT 10 POUCES ET 20 PIEDS RESPECTIVEMENT. IL EST IMPORTANT DE BIEN REINSTALLER ET RESCELLER L'EVENT APRES AVOIR ASSURE LE MAINTIEN DU SYSTEME DE PRISE D'AIR.

DEGAGEMENTS MINIMAUX DES MATERIAUX COMBUSTIBLES:

A 4" B 2" C 2"

EVENT SUPERIEUR 2" ENTRE LE DESSUS DU FOYER EVENT INFERIEUR 1" ET LE PLAFOND 48” COTES DE L'EVENT 1"

This illustration is for referece only. Refer to the rating plate on the appliance for accurate information.

note:

The rating plate must remain with the appliance at all times. It must not be removed.

COLONNE D'EAU(P)

AFUE: 64%

W385-1962 / A

1.4 mobile home installation

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plate.

This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. Built in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base. Use appropriate fasteners, inserted through the holes in the base to secure. For free standing products contact your local authorized dealer / distributor for the appropriate securing kit. For mobile home installations, the appliance must be fastened in place. It is recommended that the appliance be secured in all installations. Always turn off the pilot and the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the appliance, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

Conversion Kits

This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (P). To convert from one gas to another, consult your Authorized dealer/distributor.

note:

Conversion kits are not available for Vent Free appliances.

8

W415-2207 / B / 02.05.18

1.5 hardware list

general information

EN

1

Description Quantity

1/4” Hex Head Screw 3

1

1 3/4” Pan Head Screw 4

2

note:

Only fasteners supplied with the appliance are illustrated.

2

W415-2207 / B / 02.05.18

9

25 5/8"

651mm

23 5/8"

600mm

17 1/2"

445mm

23 1/2"

597mm

12 3/4"

324mm

Ø

4"

102mm

Ø 7"

178mm

SAFETY BARRIER

EN

general information

1.6 dimensions

FRONT VIEW

RIGHT SIDE VIEW

TOP VIEW

10

W415-2207 / B / 02.05.18

2.0 venting requirements

WARNING

!

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• If venting is included with spacers, the vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W010-0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this gap is maintained. These spaces must not be removed.

This appliance uses a 4” (102mm) exhaust / 7” (178mm) air intake vent pipe system. Refer to the section applicable to your installation.

For safe and proper operation of the appliance, follow the venting instructions exactly. Deviation from the minimum vertical vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes (5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a

ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for 400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the initial installation.

note:

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate constructions such as a chimney as part of the vent system is not permitted.

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab, follow the installation procedure provided with the venting components or on the website for your venting supplier. A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

EN

Vent Manufacturer

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SuperSeal 4DNA Metal-Fab www.mtlfab.com

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following termination kits: wall terminal kit GD-222, GD-222R, or 1/12 to 7/12 pitch roof terminal kit GD-110, 8/12 to 12/12 roof terminal kit GD-111, ﬂ at roof terminal kit GD-112 or periscope kit GD-201 (for wall penetration below grade). With ﬂ exible venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD-220 or the 10 foot (3.1m) vent kit GD-330. For stoves only: wall terminal kit GD-175 (venting included).

Starter Adapter Part Number Supplier Website

W415-2207 / B / 02.05.18

11

!

WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• If venting is included with spacers, the vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W010-0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this gap is maintained. These spaces must not be removed.

This appliance uses a 4” (102mm) exhaust / 7” (178mm) air intake vent pipe system. Refer to the section applicable to your installation.

For safe and proper operation of the appliance, follow the venting instructions exactly. Deviation from the minimum vertical vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes (5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a

ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for 400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

Vent Manufacturer

Starter Adapter Part Number Supplier Website

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SuperSeal 4DNA Metal-Fab www.mtlfab.com

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab, follow the installation procedure provided with the venting components or on the website for your venting supplier. A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the initial installation.

note:

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate constructions such as a chimney as part of the vent system is not permitted.

This template must be used in conjunction with templates 7.1.1 or 7.1.2, depending on termination shape (i.e. round, or round and square). See appropriate templates folder.

EN

venting requirements

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20 feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

Horizontal runs may have a 0” rise per foot or 0mm rise per meter however for optimum performance it is recommended that all horizontal runs have a minimum 1/4” rise per foot or 21mm rise per meter using ﬂ exible venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air gap all around between the inner liner and outer liner is required for safe operation.

12

W415-2207 / B / 02.05.18

2.1 typical venting installation

24” (61cm) MIN.

REGARDLESS OF

HORIZONTAL VENT

LENGTH

25 5/8”

(65.1cm)

venting requirements

16” (40.6cm)

EN

40FT (12m)

MAX

3FT (1m)

MIN

24” (61cm) MAXIMUM

25 5/8”

(65.1cm)

WARNING

!

• The maximum horizontal run with a 57” (1.45m) vertical rise immediately above the appliance is 20 feet (6.1m).

W415-2207 / B / 02.05.18

13

EN

venting requirements

2.2 special vent installations

2.2.1 periscope termination

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when ﬁ nal grading is completed, the bottom air slot is located a minimum of 12” (305mm) above grade. The maximum allowable vent length is 10’ (3.1m) for a ﬁ replace and 8’ (2.4m) for a stove.

WARNING

!

• Below grade installation maximum 8ft (2.4m) vent length.

• Use GD201 periscope kit.

• Horizontal run not to exceed vertical rise.

12”

(305mm) MIN

TO GRADE

24” (610mm) MIN.

REGARDLESS OF OF

HORIZONTAL VENT

LENGTH

25 5/8”

(651mm)

2.2.2 corner termination

SAFETY

BARRIER

24” (610mm)

MAX.

14

W415-2207 / B / 02.05.18

2.3 vent terminal clearances

Covered balcony applications

venting requirements

R

EN

††*

Q

S

P

G

Q

= 3 feet

MIN

(0.9m)

INSTALLATIONS

CANADA U.S.A.

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

A

Δ

12” (30.5cm)

B

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

C

D

E

F

G

H

I

J

K

L

M

18”

(45.7cm)**

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

0” (0mm)*** 0” (0mm)***

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

3’(0.9m) 3’(0.9m)****

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch or deck.

9” (229mm) ΔClearance to windows or doors that open.

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m) from the center line of the terminal.

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum vertical distance of 15’ (4.6m).

note:

Wall terminals are for illustration purposes only. Size and shapes may vary.

R

= 2 x

MAX

Q

ACTUAL

R

MAX

≤ 15 feet

(4.6m)

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

N

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

O

8’ (2.4m) 8’ (2.4m)

P

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

Q

6’ (1.8m) 6’ (1.8m)

R

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

S

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Roof must be non-combustible without openings.

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening between the terminal and the open side of the structure.

note:

Clearances are to be in accordance with local installation codes and the requirements of the gas supplier. In their absence, clearances are to be as listed above and are based on national codes.

W415-2207 / B / 02.05.18

15

EN

venting requirements

2.4 horizontal termination

39’ 2”

V

V+H ≤ 40 ft. (For longer vent runs, a power vent is required). H ≤ 20 ft. V + H are measured from the centre of vent elbows. Elbows are considered as 90º. Two 45º elbows = One 90º elbow.

5 1/2 elbow zone

30’

4 1/2 elbow zone

3 1/2 elbow zone

2 1/2 elbow zone

1 1/2 elbow zone*

20’

4”

MAXIMUM

57”

24”

MINIMUM

0’

Centre of

Base of Air

Collar

15’

10’

5’

0’

10”

24”

MAXIMUM

5’

10’

15’

20’

25’

H

* 1 1/2 elbows constitute the 45° elbow directly off the appliance and an additional 90° elbow.

16

W415-2207 / B / 02.05.18

2.5 vertical termination

venting requirements

EN

V

20’

40’

30’

V+H ≤ 40 ft. (For longer vent runs, a power vent is required). H ≤ 20 ft. V + H are measured from the centre of vent elbows. Elbows are considered as 90º. Two 45º elbows = One 90º elbow.

6 1/2 elbow zone

5 1/2 elbow zone

4 1/2 elbow zone

3 1/2 elbow zone

2 1/2 elbow zone

1 1/2 elbow zone*

3’

MINIMUM

0’

Centre of

Base of Air

Collar

15’

10’

5’

0’

4”

MINIMUM

5’

10’

15’

20’

25’

H

* 1 1/2 elbows constitute the 45° elbow directly off the appliance and an additional 90° elbow.

W415-2207 / B / 02.05.18

17

!

WARNING

EN

venting requirements

2.6 vertical through existing chimney

• Risk of ﬁ re.

• Co-axial to co-linear venting conﬁ gurations must only be used in a non-combustible chimney or enclosure. Installation in a combustible enclosure could result in a ﬁ re.

This appliance is designed to be attached to a 3” (76.2mm) co-linear aluminum ﬂ ex vent system running the full length of a masonry chimney.

The ﬂ ex liners accommodate any contours of a masonry chimney, however, it is necessary to keep the ﬂ exible liners as straight as possible. The inlet air collar of the termination cap must be connected to the air intake ﬂ ex liner and the exhaust collar must be connected to the exhaust ﬂ exible liner.

Both Simpson Duravent and Selkirk co-linear to co-axial adaptors have been approved on this appliance

AIR

INTAKE

TERMINATION

EXHAUST

FLUE

FLEX

LINER

note:

A vent adaptor will be required directly off the appliance.

Follow vent manufacturer’s installation instructions.

Different manufacturer’s venting components must not be combined. Once the preferred manufacturer’s appliance adaptor has been attached, the remainder of the system must be that of the same manufacturer.

The only exception to this rule is to use Wolf Steel’s approved 3” (76.2mm) ﬂ ex liner and co-linear termination.

* Measured from appliance ﬂ ue collar to termination ﬂ ue collar

* 40 FT (12.2m)

MAX.

10 FT (3.1m)

MIN

COAXIAL TO

CO-LINEAR ADAPATOR

APPLIANCE

VENT ADAPTOR

18

W415-2207 / B / 02.05.18

3.0 installation

!

WARNING

• Ensure to unpack all loose materials from inside the ﬁ rebox prior to connecting the gas and electrical supply

• If your appliance is supplied with a remote, ensure the remote receiver is in the “OFF” position prior to connecting the gas and electrical supply to the appliance.

• For safe and proper operation of the appliance, follow the venting instructions exactly.

• The appliance exhaust ﬂ ue collar must be sealed using Mill Pac. All exhaust and intake vent pipe joints must be sealed using red RTV high temp silicone sealant (W573-0002) (not supplied) or black high temp Mill Pac (W573-0007) (not supplied).

• If using pipe clamps to connect rigid vent components, a minimum of 3 screws must also be used to ensure the connection cannot slip off.

• Do not clamp the ﬂ exible vent pipe.

• Risk of ﬁ re, explosion, or asphyxiation. Improper support of the entire venting system may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions.

• Risk of ﬁ re, do not allow loose materials or insulation to touch the vent pipe. Remove insulation to allow for the installation of the attic shield and to maintain clearances to combustibles.

• Do not ﬁ ll the space between the vent pipe and enclosure with any type of material. Do not pack insulation or combustibles between ceiling ﬁ restops. Always maintain speciﬁ ed clearances around venting and ﬁ restop systems. Install wall shields and ﬁ restops as speciﬁ ed. Failure to keep insulation or other materials away from vent pipe may cause ﬁ re.

EN

W415-2207 / B / 02.05.18

19

This application occurs when venting through a roof. Installation kits for

WARNING

EN

installation

3.1 horizontal installation

!

• The ﬁ restop assembly must be installed with the vent shield to the top.

• Terminals must not be recessed into a wall or siding more than the depth of the return ﬂ ange of the mounting plate.

This application occurs when venting through an exterior wall. Having determined the correct height for the air terminal location, cut and frame a hole in the exterior wall, as illustrated, to accommodate the ﬁ restop assembly. Dry ﬁ t the ﬁ restop assembly before proceeding to ensure the brackets on the rear surface ﬁ t to the inside surface of the horizontal framing.

The length of the vent shield may be cut shorter for combustible walls that are less than 8 1/2” (215.9mm) thick but the vent shield must extend the full depth of the combustible wall.

note:

Do not ﬁ ll the air space between the ﬁ restop spacer and the exterior wall with any type of insulating material (i.e. spray foam).

A. Assemble the shield to the spacer as shown, using the 3

shorter screws supplied.

B. Place the ﬁ restop top so that the vent shield covers the top of

the vent within the opening. Ensure that both spacer and shield maintain the required clearance to combustibles.

C. Secure the spacer in place using the 4 longer screws supplied.

Once the vent pipe is installed in its ﬁ nal position, apply sealant between the pipe and the ﬁ restop spacer.

3.2 vertical installation

CAULKING

FIRESTOP

SPACER

CAULKING

10 11/16”

ADD

(27.14cm)

VENT

SHIELD

note:

The above is for illustration purposes only. Vents do not always pass through center of frame.

HEIGHT

HIGH

FINISHING MATERIAL

10 11/16”

ADD

(27.14cm)

WIDTH

WIDE

DETERMINE THE CORRECT HEIGHT

various roof pitches are available from your authorized dealer / distributor. See the “accessories” section to order speciﬁ c kits required.

A. Determine the air terminal location, cut and frame a square opening,

as illustrated, in the ceiling and the roof to provide the minimum 1" (25mm) clearance between the vent pipe and any combustible material. Try to center the vent pipe location midway between two joists to prevent having to cut them. Use a plumb bob to line up the center of the openings. A vent pipe shield will prevent any materials such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe. Nail headers between the joist for extra support.

B. Apply a bead of caulking (not supplied) to the framework or to the

Wolf Steel vent pipe shield plate or equivalent (in the case of a ﬁ nished ceiling), and secure over the opening in the ceiling. A ﬁ restop must be placed on the bottom of each framed opening in a roof or ceiling that the venting system passes through. Apply a bead of caulking all around and place a ﬁ restop spacer over the vent shield to restrict cold air from being drawn into the room or around the ﬁ replace. Ensure that both spacer and shield maintain the required clearance to combustibles. Once the vent pipe is installed in its ﬁ nal position, apply Mill Pac sealant (W573-0007) (not supplied) or red RTV silicone (W573-0002) (not supplied) between the pipe and the ﬁ restop assembly.

C. In the attic, slide the vent pipe collar down to cover up the open end

of the shield and tighten. This will prevent any materials, such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

Vent Pipe

Shield

Vent Pipe

Shield

Firestop

underside

of joist

Caulking

Vent Pipe

Collar

20

W415-2207 / B / 02.05.18

3.3 horizontal air terminal installation

A. Stretch the inner ﬂ ex pipe to the required length taking

depth of its return ﬂ ange.

ADD FASTENER TYPE

Pipe

Telescopic sleeve

Venting

TOP VENT

20" (51cm)

Coupler

REAR VENT

Air terminal

Telescopic sleeve

20" (51cm)

Coupler

Venting

WARNING

!

• Terminals must not be recessed into a wall or siding more than the depth of the return ﬂange of the mounting plate.

• Do not allow the inner ﬂex pipe to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight.

into account the additional length needed for the ﬁ nished wall surface. Apply a heavy bead of the red RTV silicone (W573-0002) (not supplied) to the inner sleeve of the air terminal. Slip the vent pipe a minimum of 2” (50.8mm) over the inner sleeve of the air terminal and secure with a minimum of 3 screws.

B. Using the outer ﬂ ex pipe, slide over the outer combustion

air sleeve of the air terminal and secure with a minimum of 3 screws. Seal using red RTV silicone (W573-0002) (not supplied).

C. Insert the vent pipes through the ﬁ restop maintaining

the required clearance to combustibles. Holding the air terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing with caulking (not supplied).

D. If more vent pipe needs to be used to reach the ﬁ replace,

E. Stove Appliances Only: From inside the house, using

The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the

couple them together, as illustrated. The vent system must be supported approximately every 3 feet (0.9m) for both vertical and horizontal runs. Use non-combustible strapping to maintain the minimum clearance to combustibles.

Red RTV Silicone (W573-0002) (not supplied), seal between the vent pipe and the ﬁ restop. Then slide the black trim collar over the vent pipe up to the ﬁ restop.

Type 1 (x3)

Caulking

Screws

(Supplied)

Red RTV Silicone

Outer Flex

Pipe

ADD GRAPHIC

installation

Type 2 (x4)

Inner Flex

Pipe

Outer Rigid Pipe

2" (50.8mm) Overlap

Red RTV Silicone

Inner Flex

Outer Flex Pipe

Screws

Inner Coupler

Outer Coupler

Outer Rigid

Outer Flex

Pipe

EN

3.4 extended horizontal and corner air terminal installation

FOR REAR VENT ONLY: A 45° corner installation can have 0” (0mm) rise between the appliance combustion air collar and the air terminal. In this case, vent lengths must be kept to a maximum of 24” (61cm). For longer vent lengths, a minimum vertical rise of 24” (61cm) is required.

A. Follow the instructions for "horizontal air terminal installation" section.

B. Continue adding components alternating inner rigid pipe and outer

rigid pipe. Ensure that all inner rigid pipe and elbows have sufﬁcient vent spacers attached and each component is sealed and securely fastened to the one prior. Attach the inner telescopic sleeve to the vent run. Repeat using the outer telescopic sleeve. Seal and secure as before. To facilitate completion, attach inner and outer couplers to the air terminal.

C. Install the air terminal. See “horizontal air terminal installation” section.

Extend the outer telescopic sleeve; connect to the air terminal assembly. Fasten with self tapping screws and seal.

AIR TERMINAL

20" (508mm) COUPLER

TELESCOPIC SLEEVE

VENTING

Add Image

W415-2207 / B / 02.05.18

21

air terminal installation” section.

!

WARNING

EN

installation

3.5 vertical air terminal Installation

• Maintain a minimum 2” (51mm) space between the air inlet base and the storm collar.

note:

Fastening hardware provided with appropriate roof terminal and liner kits.

A. Fasten the roof support to the roof using 6 screws. The roof support is

optional. In this case, the venting is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the optional roof support.

B. Stretch the inner ﬂ ex pipe to the required length. Slip the inner ﬂ ex

pipe a minimum of 2” (51mm) over the inner pipe of the air terminal connector and secure with a minimum of three screws, when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws when using 8/10 or 8/11 venting. Seal using a heavy bead of red RTV silicone (W573-

0002) (not supplied).

C. Repeat using the outer ﬂ ex pipe, using a heavy bead of red RTV

silicone (W573-0002) (not supplied) and a minimum of three screws, when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws when using 8/10 or 8/11 venting.

D. Thread the air terminal connector / vent pipe assembly down through

the roof. The air terminal must be positioned vertically and plumb. Attach the air terminal connector to the roof support, ensuring that the top of the air terminal is 16” (40.6cm) above the highest point that it penetrates the roof.

E. Remove nails from the shingles, above and to the sides of the air

terminal connector. Place the ﬂ ashing over the air terminal connector leaving a min. 3/4” (19mm) of the air terminal connector showing above the top of the ﬂ ashing. Slide the ﬂ ashing underneath the sides and upper edge of the shingles. Ensure that the air terminal connector is properly centered within the ﬂ ashing, giving a 3/4” (19mm) margin all around. Fasten to the roof. Do not nail through the lower portion of the ﬂ ashing. Make weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the ﬂ ashing with rooﬁ ng material.

F. Aligning the seams of the terminal and air terminal connector, place the

terminal over the air terminal connector making sure the vent pipe goes into the hole in the terminal. Secure with a minimum of three screws, when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws when using 8/10 or 8/11 venting.

G. Apply a heavy bead of weatherproof caulking 2” (51mm) above the

ﬂ ashing. Install the storm collar around the air terminal and slide down to the caulking. Tighten to ensure that a weather-tight seal between the air terminal and the collar is achieved.

H. If more vent pipe needs to be used to reach the appliance, see “horizontal

Connector

2” (51mm)

Roof Support

Air

Terminal

Inner Flex Pipe

Inner Pipe

Red RTV

Silicone

(W572-0002)

Outer Flex Pipe

Outer Rigid Pipe

Air Inlet Base

Caulking

Sto r m Collar

Weather Sealant

Flashing

22

W415-2207 / B / 02.05.18

3.6 appliance vent connection

A. Attach the adjustable pipe to the last section of rigid pipe. Secure with

!

WARNING

• Check for gas leaks by brushing on a soap and water solution. Do not use open ﬂ ame.

screws and seal.

B. Install the inner ﬂ ex pipe to the appliance. Secure with a minimum of

three screws and ﬂ at washers when installing 3”/5”, 4”/7” or 5”/8” venting, or six screws and ﬂ at washers when installing 8”/10” or 8”/11” venting. Seal the joint and screw holes using Mill Pac sealant (W573-0007) (not supplied).

C. Run a bead of high temperature red RTV silicone (W573-0002) (not

supplied) around the inside of the air intake collar. Pull the adjustable pipe a minimum 2” (50.8mm) into the air intake collar.

note:

Always ﬁ nish vent system installation with the appliance vent connection. Ensure that the sealant is not visible on the exterior pipes once installation is completed. An optional decorative black band may be available with this appliance. In the event that the venting must be disassembled, care must be taken to reseal the venting.

3.7 gas installation

• Risk of ﬁ re, explosion, or asphyxiation. Ensure there are no ignition sources such as sparks or open ﬂ ames.

• Support gas control when attaching gas supply pipe to prevent damaging gas line.

• Always light the pilot whether for the ﬁ rst time or if the gas supply has run out with the glass door opened or removed. Purging of the gas supply line should be performed by a qualiﬁ ed service technician. Ensure that a continuous gas ﬂ ow is at the burner before closing the door. Ensure adequate ventilation. For gas and electrical locations, see “dimensions” section.

• All gas connections must be contained within the appliance when complete (gas ﬁ replaces only).

• High pressure will damage valve. Disconnect gas supply piping before testing gas line at test pressures above 1/2 PSIG.

• Valve settings have been factory set, do not change.

installation

#8 X 1/2”

Self Drilling

Screws

INSERT

2” (50.8mm)

IMAGE HERE

Overlap

High Temperature Sealant

EN

Installation and servicing to be done by a qualiﬁ ed installer.

• Move the appliance into position and secure.

• If equipped with a ﬂ ex connector, the appliance is designed to accept a 1/2” (13mm) gas supply. Without the

connector, it is designed to accept a 3/8” (9.5mm) gas supply. The appliance is equipped with a manual shut off valve to turn off the gas supply to the appliance.

• Connect the gas supply in accordance to local codes. In the absence of local codes, install to the current

CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States.

• When ﬂ exing any gas line, support the gas valve so that the lines are not bent or kinked.

• The gas line ﬂ ex-connector should be installed to provide sufﬁ cient movement for shifting the burner assembly

on its side to aid with servicing components.

W415-2207 / B / 02.05.18

23

MINIMUM CLEARANCE TO COMBUSTIBLES MUST BE MAINTAINED OR A SERIOUS FIRE HAZARD

COULD RESULT.

ENTIRELY OF NON-COMBUSTIBLE MATERIALS (I.E. STEEL STUDS, CEMENT BOARD, ETC.).

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

!

WARNING

EN

installation

3.8 minimum clearance to combustibles

WARNING

!

• Minimum clearance to combustibles must be maintained or a serious ﬁre hazard could result.

• Framing or ﬁnishing materials closer than the minimums listed must be constructed entirely of non-combustible materials (i.e. steel studs, cement board, etc.).

• Never obstruct the front opening of the appliance.

As long as clearance to combustibles is kept within the required distances, the most desirable and beneﬁcial location for a Napoleon® appliance is in the centre of a building, thereby allowing the most efﬁcient use of the heat created. The location of windows, doors and the trafﬁc ﬂow in the room where the appliance is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂoor or roof joist.

A. 4” (102mm) B. 2” (51mm)* C. 2” (51mm)

To ceiling from appliance top 48” (1219mm)

Horizontal vent:

Sides and bottom 1” (25mm) Top 2” (51mm)

Vertical vent:

All sides 1” (25mm)

*At a distance of 2” (51mm) from the wall, installation or service to the blower may not be practical. A minimum of 5” (127mm) will be required in order to install the blower.

If less than 5” (127mm) clearance is maintained between the back of the appliance and the back wall, it will be necessary to disconnect the venting and gas pipe to move the appliance out for installation or service of the blower.

24

W415-2207 / B / 02.05.18

COMBUSTIBLE MANTE TRIM M

ETC.) ARE CLEARLY MAINTAINED.

!

WARNING

25

EN

3.9 minimum mantel or shelf clearances

WARNING

!

• Risk of ﬁre!

• Maintain all speciﬁed air space clearances to combustibles.

• Failure to comply with these instructions may cause a ﬁre or cause the appliance to overheat.

• Ensure all clearances (i.e. back, side, top, vent, hearth, mantel, front, etc.) are clearly maintained.

When the appliance is rear vented, a mantel or shelf may be installed above the GDS25-1 at a minimum distance of 8” (203mm).

installation

EN

L OR ATERIAL

8” (203mm)

MIN.

12” (305mm)

MAX. MANTEL DEPTH

2” (51mm)

COMBUSTIBLE

NON-COMBUSTIBLE

BRICK

1” (25mm)

0” (0mm) IF NONCOMBUSTIBLE FINISHING IS USED SUCH AS BRICK AND STONE

24 1/2”

(622mm)

2”

(51mm)

W415-2207 / B / 02.05.18

25

Retainer

Door

Tab

Front

Bracket

Screws

Front

Front Legs

!

WARNING

GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.

the appliance.

from the side pieces by removing the screws from the brackets located in the upper inside corners.

remove.

FRONT

SCREWS

BRACKET

3

2

DOOR

RETAINER

FRONT

LEGS

TAB

FRONT

!

WARNING

RISK OF FIRE!

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

REMOVED, CRACKED, BROKEN OR SCRATCHED.

72.4

casting.

WARNING

EN

4.0 ﬁnishing

!

• Risk of ﬁ re!

• Never obstruct the front opening of the appliance.

• Do not strike, slam, or scratch. Do not operate appliance with glass removed, cracked, or scratched.

4.1 cast front installation and removal

WARNING

!

• Glass may be hot.

• Do not touch glass until cooled.

A. Remove safety barrier. B. Lift the top cast piece off of

the appliance.

C. Detach the front cast piece

from the side pieces by removing the screws from the brackets located in the upper inside corners.

D. Slide the front straight up to

remove.

Follow the above steps in reverse in order to reinstall the cast front. Ensure that the tabs on the underside of the front ﬁt behind the front legs.

note:

It is not necessary to remove the cast front in order to remove the door.

4.2 safety barrier installation and removal

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance and shall be installed.

A. Lift the top casting up and remove the safety barrier. Remove and discard plastic. B. Tilt the top of the safety barrier and hook under the top casting, make sure to hold the safety barrier. C. Slightly lift the bottom of the safety barrier and push onto theappliance. Careful not to scratch the bottom

casting.

D. Reverse these steps to remove.

SAFETY BARRIER

26

W415-2207 / B / 02.05.18

LATCHES

DOOR

4.3 glass door installation and removal

WARNING

!

• Do not substitute materials.

A. Remove safety barrier. B. Lift the top cast piece off of the appliance. C. Pull handle and rotate 90°. D. Slide the door straight up to remove.

Follow the above steps in reverse in order to reinstall the door. Ensure that the bottom of the door engages the door retainer before closing the latches.

ﬁnishing

EN

4.4 log placement

WARNING

!

• Logs must be placed in the exact location in appliance. Do not change from the proper log positions, as appliance may not function properly.

• The logs are fragile and should be handled with care.

It is not necessary to remove the cast front, however, this will make for a more simple log installation. In order to assemble the log set, the glass door must be removed, see “cast front / glass door installation and

removal” section.

BRACKET

LOG LOCATING SCREWS

A. Place the rear log, as shown, onto the rear log

support brackets. Ensure the cutout on the left underside of the log, ﬁts over the pilotassembly. Bend the bracket on the left side to help retain the rear log.

W415-2207 / B / 02.05.18

27

MAIN

BURNER

SWITCH

ACCENT

LIGHT

SWITCH

FAN

CONTROL

LOGO

1/2”

C. Place the hole in the underside of log #3 onto

the locating screw, on the right side of the burner. The bottom branch of log #3 sits in front of, and against, the right end of log #2.

D. Reinstall the glass door & front.

EN

ﬁnishing

B. Place the hole in the underside of log #2

onto the locating screw, on the left side of the burner. The ﬁbre burner is formed to cradle the centre of the log.

4.5 logo placement

Remove the backing from the logo and position onto the control door as shown.

C. Place the hole in the underside of log #3 onto

the locating screw, on the right side of the burner. The bottom branch of log #3 sits in front of, and against, the right end of log #2.

D. Reinstall the glass door & front.

W415-2207 / B / 02.05.18

28

5.0 optional blower installation

WARNING

!

• Ensure the appliance is completely cool before starting installation.

• To avoid danger of suffocation, keep the packaging bag away from babies and children. Do not use in cribs, beds, carriages, or play pens. This bag is not a toy. Knot before throwing away.

A. Disconnect power supply from the appliance.

B. Open the control door located at the bottom front of the appliance (FIG. 1).

C. Remove the 2 screws holding the left control box cover (FIG. 2).

D. Slide the control box cover forward and remove from the appliance (FIG. 3 and 4).

FIG. 1 FIG. 2

EN

FIG. 3

FIG. 4

W415-2207 / B / 02.05.18

29

EN

optional blower installation

E. Access blower wire leads. Remove 2 insulation connectors from blower wire leads.

F. Route the blower wire through the rear hole of the housing (FIG. 5 and 6).

G. Snap bushing over blower wire and press into rear hole of housing.

H. Place blower housing close to the rear of the appliance. Route wire through hole in blower housing and

connect the spade connectors to blower (FIG. 7).

I. Align the blower to the rear side of the control box and fasten it with 2 screws included with the kit (FIG. 8).

J. Re-install control box side cover to the control box using the 2 screws previously removed in Step C.

K. Close the control door (FIG. 9).

L. Reconnect power supply to the appliance.

FIG. 5

FIG. 7

FIG. 6

BUSHING

Rear Hole

Wire Harness

FIG. 8

Spade Connectors

FIG. 9

30

W415-2207 / B / 02.05.18

6.0 wiring diagram

ELECTRONIC

WARNING

!

• Do not wire 110 volts to the valve or wall switch.

This appliance must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian electrical code in Canada or the ANSI/NFPA national electrical code in the United States.

BLOWER

OPTIONAL

(POWER CORD)

WIRE HARNESS)

(BLOWER/NIGHT LIGHT

EN

NIGHT

BLOWER

LIGHT

JUMPER

PILOT

IGNITION

ELECTRONIC

VALV E

note:

Jumper is only present when appliance is equipped and operated with remote control.

(RECEIVER)

RESET

BUTTON

WITH RESET BUTTON

BATTERY HOLDER COMPLETE

note:

This appliance is equipped with a three-prong (grounding) plug for protection against shock hazard and should be connected into a properly grounded circuit. Do not cut or remove the grounding prong from the plug.

W415-2207 / B / 02.05.18

31

!

WARNING

D.

EN

7.0 operation

• If you do not follow these instructions exactly, a ﬁ re or explosion may result causing property damage, personal injury, or loss of life.

• If applicable, always light the pilot whether for the ﬁ rst time or if the gas supply has run out with the glass door opened or removed.

Ensure that a continuous gas ﬂ ow is at the burner before installing the door. When lit for the ﬁ rst time, the appliance will emit an odor for a few hours. This is a normal temporary condition caused by the “burn-in” of paints and lubricants used in the manufacturing process and will not occur again. After extended periods of non-operation, such as, following a vacation or warm weather season, the appliance may emit a slight odor for a few hours. This is caused by dust particules in the heat exchanger burning off. In both cases, open a window to sufﬁ ciently ventilate the room.

FOR YOUR SAFETY READ BEFORE LIGHTING

• Do not turn on if children or other at risk individuals are near the appliance.

• This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

• Before operating, smell all around the appliance area for gas and next to the ﬂ oor because some gas is heavier than air and will settle on the ﬂ oor.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician to inspect the appliance and replace any part of the control system and any gas control which has been underwater.

WHAT TO DO IF YOU SMELL GAS

• Turn off all gas to the appliance.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

LIGHTING INSTRUCTIONS

note:

This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

A. Stop! Read the above safety information on this label. B. Remove batteries from the transmitter and set thermostat to lowest setting, if

equipped.

C. Turn off all electrical power to the appliance. D. Open the glass door, if equipped. E. Turn the manual shut-off valve clockwise to the “OFF” position. (Shut-off valve is

located on the ﬂ ex connector).

F. Wait ﬁ ve (5) minutes to clear out any gas. If you smell gas including near the

ﬂ oor, STOP! Follow the instructions above in the “WHAT TO DO IF YOU SMELL GAS” section. If you don’t smell gas; close the glass door and go to the next step.

G. Turn the manual shut-off valve counter clockwise to the “ON” position. H. Turn on all electrical power to the appliance and re-install the batteries into the

transmitter. Set thermostat to desired setting, if equipped.

I. Turn on the remote wall switch to the appliance. J. If the appliance will not operate, follow instructions “TO TURN OFF GAS” and

call your service technician or gas supplier.

TO TURN OFF GAS A. Set thermostat to lowest setting, if equipped. B. Turn off the remote wall switch to the appliance. C. Turn off all electric power to the appliance if service is to be performed.

Turn manual shutoff valve clockwise to the “OFF” positon. Do not force.

add gas knob

add gas valve

32

W415-2207 / B / 02.05.18

7.1 general transmitter layout

Transmission

Flame ON

Key Lock

operation

Low battery alarm

Room

Temperature

CPI mode

EN

Blower

note:

Transmitter is optional with this model.

7.2 initializing the transmitter / battery holder for the ﬁrst time

A. Install the 4 AA batteries into the Proﬂame 2 battery holder, note the polarity of the batteries and insert as

indicated on the cover (+/-).

B. Ensure the 3 position slider switch is switched to the “REMOTE” position (middle position). C. Press the reset/programming button, use a small object such as a paper clip in order to reach the button

marked PRG, as shown in the illustration below.

D. The battery holder will beep 3 times to indicate that it’s ready to synchronize with the transmitter. E. Install the 3 AAA batteries into the transmitter, as shown in the photograph below, then press the ON

button, The battery holder will beep 4 times to indicate that the transmitter’s command is accepted.

note:

The initializing process must be completed within 10 seconds of pressing the reset / program button (PRG).

Light

TRANSMITTER

BATTERY HOLDER

SLIDER SWITCH

RESET/PROGRAM

BUTTON (PRG)

(4) AA Batteries

W415-2207 / B / 02.05.18

33

A. Press the ON/OFF key on the transmitter. The transmitter display will show

all active icons on the screen. A single “beep” from the receiver will conﬁ rm reception of the command.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

76

°F

OFF

76

°F

ON

°F

ADD TITLE: TEMPERATURE DISPLAY

A. With the system in the off position, press the Temperature Key and the

ADD TITLE: HAND HELD REMOTE OPERATION

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

OFF

76

°F

ON

76

°F

°F °C

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

OFF

76

°F

ON

76

°F

°F °C

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

76

°F

OFF

76

°F

ON

°F

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

OFF

76

°F

ON

76

°F

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

OFF

76

°F

ON

76

°F

°F °C

A. Press the ON/OFF key on the transmitter. The transmitter display will show

all active icons on the screen. A single “beep” from the receiver will conﬁ rm reception of the command.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

76

°F

OFF

76

°F

ON

°F

ADD TITLE: TEMPERATURE DISPLAY

A. With the system in the off position, press the Temperature Key and the

mode key at the same time to change from degrees F to C.

B. Look at the LCD screen on the transmitter to verify that a C or F is

visible to the right of the Room Temperature display.

ADD TITLE: HAND HELD REMOTE OPERATION

The remote transmitter can operate as a room thermostat. The thermostat can be set to a desired temperature to control the comfort level in the

room. A. Press the thermostat key. The LCD display on the transmitter will show that the

room is on and the set temperature is now displayed.

B. To adjust the set temperature, press the mode key until the desired set

temperature is displayed on the LCD screen of the transmitter.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

Set Temperature

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

°F

ON

°F °C

ADD TITLE: ROOM THERMOSTAT

ADD TITLE: SMART THERMOSTAT

The Smart Thermostat function adjusts the ﬂ ame height according to the difference between the set temperature and the actual room temperature. As the room temperature gets closer to the set point the Smart Function will automatically adjust the ﬂ ame down.

A. Press the thermostat key until the word SMART appears to the right of the temperature

bulb graphic.

B. To adjust the set temperature, press the mode key until the desired set temperature is

displayed on the LCD screen at the transmitter.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

ON

SMART

°F °C

The remote control has six (6) ﬂ ame levels. With the system on and the ﬂ ame level at the maximum, press the Down

ADD TITLE: FLAME HEIGHT

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

Set Temperature

76

°F

MAX

76

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

ON

SMART

°F °C

76

°F

OFF

76

°F

ON

76

°F

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

OFF

76

°F

ON

76

°F

°F °C

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

OFF

76

°F

ON

76

°F

°F °C

A. Press the ON/OFF key on the transmitter. The transmitter display will show

all active icons on the screen. A single “beep” from the receiver will conﬁ rm reception of the command.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

76

°F

OFF

76

°F

ON

°F

ADD TITLE: TEMPERATURE DISPLAY

A. With the system in the off position, press the Temperature Key and the

mode key at the same time to change from degrees F to C.

B. Look at the LCD screen on the transmitter to verify that a C or F is

visible to the right of the Room Temperature display.

ADD TITLE: HAND HELD REMOTE OPERATION

The remote transmitter can operate as a room thermostat. The thermostat can be set to a desired temperature to control the comfort level in the

room. A. Press the thermostat key. The LCD display on the transmitter will show that the

room is on and the set temperature is now displayed.

B. To adjust the set temperature, press the mode key until the desired set

temperature is displayed on the LCD screen of the transmitter.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

Set Temperature

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

°F

ON

°F °C

ADD TITLE: ROOM THERMOSTAT

ADD TITLE: SMART THERMOSTAT

The Smart Thermostat function adjusts the ﬂ ame height according to the difference between the set temperature and the actual room temperature. As the room temperature gets closer to the set point the Smart Function will automatically adjust the ﬂ ame down.

A. Press the thermostat key until the word SMART appears to the right of the temperature

bulb graphic.

B. To adjust the set temperature, press the mode key until the desired set temperature is

displayed on the LCD screen at the transmitter.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

ON

SMART

°F °C

The remote control has six (6) ﬂ ame levels. With the system on and the ﬂ ame level at the maximum, press the Down arrow key once and it will reduce the ﬂ ame height by one step until the ﬂ ame is turned off.

The Up Arrow Key will increase the ﬂ ame height each time it is pressed. If the Up arrow key is pressed while the system is on but the ﬂ ame is off, the ﬂ ame will come on at the high position. A single “beep” will conﬁ rm reception of the command.

ADD TITLE: FLAME HEIGHT

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

Set Temperature

76

°F

MAX

76

°F

OFF

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

ON

SMART

°F °C

If the appliance is equipped with a hot air circulating fan, the speed of the

ADD TITLE: FAN SPEED

76

°F

OFF

76

°F

ON

76

°F

76

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

OFF

76

°F

ON

76

°F

°F °C

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

OFF

76

°F

ON

76

°F

°F °C

Your remote system may have a built in timer (in thermostat mode) that enables the blower (if equipped) to cycle on and off automatically when the burner turns on and off. With the remote control fan speed preset at the preferred speed, the blower will come on approximately 5 minutes after the main burner comes on and will shut off approximately 12 minutes after the burner shuts off.

This time delay is designed to maximize the blower distribution of heated air. If at any time the burner re-ignites before the twelve minutes are over, the fan will continue to run.

ADD TITLE: TIMED BLOWER

ADD TITLE: CHILD PROOF FUNCTION

This function will lock the keys to avoid unsupervised operation. A. Press the MODE and UP keys at the same time. B. To de-activate this function, press the MODE and UP keys at the same time.

ADD TITLE: NIGHT LIGHT

The auxiliary function controls the AUX power outlet on the Control Module which controls the NIGHT LIGHT™.

A. Use the Mode Key to guide you to the AUX icon. B. Pressing the Up Arrow Key will activate the NIGHT LIGHT™. C. Pressing the Down Arrow Key will turn the NIGHT LIGHT™ off. A single

“beep” will conﬁ rm the reception of the command.

76

°F

OFF

76

°F

ON

ADD TITLE: Night Light Dimmer Control

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

single beep will conﬁ rm reception of the command.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

76

°F

ON

SMART

°F °C

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

IPI

76

°F

CPI

ON

SMART

°F °C

76

°F

76

°F

Hi

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

At any time in the sequence, the blower (if equipped) can be manually turned on/off using the remote control.

note:

Your remote system may have a built in timer (in thermostat mode) that enables the blower (if equipped) to cycle on and off automatically when the burner turns on and off. With the remote control fan speed preset at the preferred speed, the blower will come on approximately 5 minutes after the main burner comes on and will shut off approximately 12 minutes after the burner shuts off.

This time delay is designed to maximize the blower distribution of heated air. If at any time the burner re-ignites before the twelve minutes are over, the fan will continue to run.

ADD TITLE: TIMED BLOWER

ADD TITLE: CHILD PROOF FUNCTION

This function will lock the keys to avoid unsupervised operation. A. Press the MODE and UP keys at the same time. B. To de-activate this function, press the MODE and UP keys at the same time.

ADD TITLE: NIGHT LIGHT

The auxiliary function controls the AUX power outlet on the Control Module which controls the NIGHT LIGHT™.

A. Use the Mode Key to guide you to the AUX icon. B. Pressing the Up Arrow Key will activate the NIGHT LIGHT™. C. Pressing the Down Arrow Key will turn the NIGHT LIGHT™ off. A single

“beep” will conﬁ rm the reception of the command.

76

°F

OFF

76

°F

ON

ADD TITLE: Night Light Dimmer Control

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

The auxiliary function controls the Night Light

TM

with dimmable control. A. Use the Mode Key to guide you to the Night Light icon. B. The intensity of the output can be adjusted through 6 levels.

Use the UP/DOWN arrow keys to adjust the output level. A single beep will conﬁ rm reception of the command.

ADD TITLE: CONTINUOUS PILOT / INTERMITTENT PILOT (CPI / IPI) SELECTION

A. When the transmitter is in the “OFF” position, use the Mode Key to guide

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

76

°F

ON

SMART

°F °C

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

IPI

76

°F

CPI

ON

SMART

°F °C

76

°F

76

°F

ON

76

°F

76

°F

ON

76

°F

76

°F

Hi

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

At any time in the sequence, the blower (if equipped) can be manually turned on/off using the remote control.

note:

EN

operation

7.3 temperature display

7.4 ﬂame height

7.5 blower speed

7.6 night light dimmer control

7.7 continuous pilot / intermittent pilot (CPI / IPI) selection

34

mode key at the same time to change from degrees F to C.

B. Look at the LCD screen on the transmitter to verify that a C or F is

visible to the right of the Room Temperature display.

arrow key once and it will reduce the ﬂ ame height by one step until the ﬂ ame is turned off. The Up Arrow Key will increase the ﬂ ame height each time it is pressed. If the Up arrow key is pressed while the

system is on but the ﬂ ame is off, the ﬂ ame will come on at the high position. A single “beep” will conﬁ rm reception of the command.

°F

OFF

fan can be controlled by the remote system. The fan speed can be adjusted through six (6) speeds.

A. Use the mode key to guide you to the fan control icon. B. Use the mode key to turn on/off or adjust the fan speed. A single

“beep” will conﬁ rm reception of the command.

note:

When the desired blower speed is selected, the blower will automatically come on 5 minutes after the main burner has been turned on and remain on twelve minutes after it has been turned off.

W415-2207 / B / 02.05.18

The auxiliary function controls the Night Light A. Use the Mode Key to guide you to the Night Light icon. B. The intensity of the output can be adjusted through 6 levels.

Use the UP/DOWN arrow keys to adjust the output level. A

you to the CPI mode icon.

B. Press the UP/DOWN to switch between IPI and CPI modes. A single BEEP

will conﬁ rm reception of the command.

note:

If the appliance is equipped with a CPI/IPI toggle switch, set the CPI/IPI to CPI position to enable remote CPI operation. If the switch is set to IPI then it will only work in IPI regardless of what is set on the remote control handset.

TM

with dimmable control.

68

OFF

IPI

°F °C

°F

CPI

°F

Hi

°F

Hi

°F

Your remote system may have a built in timer (in thermostat mode) that enables the blower (if equipped) to cycle on and off automatically when the burner turns on and off. With the remote control fan speed preset at the preferred speed, the blower will come on approximately 5 minutes after the main burner comes on and will shut off approximately 12 minutes after the burner shuts off.

This time delay is designed to maximize the blower distribution of heated air. If at any time the burner re-ignites before the twelve minutes are over, the fan will continue to run.

ADD TITLE: TIMED BLOWER

ADD TITLE: CHILD PROOF FUNCTION

76

°F

OFF

76

°F

ON

76

°F

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

76

°F

ON

SMART

°F °C

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

IPI

76

°F

CPI

ON

SMART

°F °C

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

At any time in the sequence, the blower (if equipped) can be manually turned on/off using the remote control.

note:

Your remote system may have a built in timer (in thermostat mode) that enables the blower (if equipped) to cycle on and off automatically when the burner turns on and off. With the remote control fan speed preset at the preferred speed, the blower will come on approximately 5 minutes after the main burner comes on and will shut off approximately 12 minutes after the burner shuts off.

This time delay is designed to maximize the blower distribution of heated air. If at any time the burner re-ignites before the twelve minutes are over, the fan will continue to run.

ADD TITLE: TIMED BLOWER

ADD TITLE: CHILD PROOF FUNCTION

This function will lock the keys to avoid unsupervised operation. A. Press the MODE and UP keys at the same time. B. To de-activate this function, press the MODE and UP keys at the same time.

ADD TITLE: NIGHT LIGHT

The auxiliary function controls the AUX power outlet on the Control Module which controls the NIGHT LIGHT™.

A. Use the Mode Key to guide you to the AUX icon. B. Pressing the Up Arrow Key will activate the NIGHT LIGHT™. C. Pressing the Down Arrow Key will turn the NIGHT LIGHT™ off. A single

“beep” will conﬁ rm the reception of the command.

76

°F

OFF

76

°F

ON

The life span of the remote batteries depends on various factors: quality of the batteries, the

position slider switch on the receiver to the “ON” position. This will bypass the remote control feature and the appliance main burner will come on if the gas valve is in the “ON” position.

ADD TITLE: LOW BATTERY / MANUAL BYPASS

ADD TITLE: Night Light Dimmer Control

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

The auxiliary function controls the Night Light

TM

with dimmable control. A. Use the Mode Key to guide you to the Night Light icon. B. The intensity of the output can be adjusted through 6 levels.

Use the UP/DOWN arrow keys to adjust the output level. A single beep will conﬁ rm reception of the command.

ADD TITLE: CONTINUOUS PILOT / INTERMITTENT PILOT (CPI / IPI) SELECTION

A. When the transmitter is in the “OFF” position, use the Mode Key to guide

you to the CPI mode icon.

B. Press the UP/DOWN to switch between IPI and CPI modes. A single BEEP

will conﬁ rm reception of the command.

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

76

°F

ON

SMART

°F °C

Blue LCD Display On / Off Key

Up / Down Arrow Key

Mode Key

Temperature Key

73 23

76

°F

68

Room Temperature

76

°F

MAX

76

°F

76

°F

76

°F

76

°F

Hi

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

76

°F

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

IPI

76

°F

CPI

ON

SMART

°F °C

76

°F

76

°F

ON

76

°F

76

°F

ON

76

°F

76

°F

76

°F

Hi

76

°F

OFF

76

°F

ON

76

°F

76

°F

68

76

°F

Hi

76

°F

OFF

76

°F

76

°F

IPI

76

°F

CPI

At any time in the sequence, the blower (if equipped) can be manually turned on/off using the remote control.

note:

If the appliance is equipped with a CPI/IPI toggle switch, set the CPI/IPI to CPI position to enable remote CPI operation. If the switch is set to IPI then it will only work in IPI regardless of what is set on the remote control handset.

note:

7.8 key lock

This function will lock the keys to avoid unsupervised operation. A. Press the MODE and UP keys at the same time. B. To de-activate this function, press the MODE and UP keys at the same time.

7.9 low battery / manual bypass

operation

°F

EN

number of ignitions, etc. When the transmitter batteries are low, a Battery Icon will appear on the LCD display before all

battery power is lost. When the batteries are replaced this icon will disappear. When the receiver batteries are low, no “beep” will be emitted from the receiver when it

receives an ON/OFF command. This in an alert for the receiver that there’s low battery. When the batteries are replaced the “beep” will be emitted from the receiver when the ON/OFF key is pressed.

If the batteries of the receiver or transmitter are low, the appliance can be turned on manually by sliding the three

W415-2207 / B / 02.05.18

°F

35

This appliance has an air shutter that has been factory set open according to

note:

EN

8.0 adjustment

8.1 restricting vertical vents

Vertical installations may display a very active ﬂame. Loosen the two screws and slide the restrictor plate blocking the exhaust path. This reduces the velocity of the exhaust gases, slowing down the ﬂame pattern and creating a more traditional ﬂame appearance. For vertical vents greater than 15 ft (5m), this restrictor must be fully closed.

RESTRICTOR SHOWN IN A

FULLY OPEN POSITION

8.2 venturi adjustment

the chart below: Regardless of venturi orientation, closing the air shutter will cause a more

yellow ﬂame, but can lead to carbonization. Opening the air shutter will cause a more blue ﬂame, but can cause ﬂame lifting from the burner ports. The ﬂame may not appear yellow immediately; allow 15 to 30 minutes for the ﬁnal ﬂame colour to be established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED INSTALLER!

It is important that the oriﬁce is securely inserted into the venturi.

Remove the 2 screws securing the burner. Air shutters have been factory set open according to the Venturi Adjustment Chart. These settings are for (maximum) horizontal termination. Adjustment may be required depending on fuel type, vent conﬁguration and altitude. After making adjustments replace the burner ensuring that the venturi tube ﬁts over the oriﬁce and replace the screws.

RESTRICTOR SHOWN IN A

FULLY CLOSED POSITION

VENTURI BURNER

AIR SHUTTER OPENING

ORIFICE

VENTURI ADJUSTMENT CHART

FUEL GDS25-1

NG 5/16” (8mm)

P 7/16” (11mm)

8.3 pilot burner adjustment

Adjust the pilot screw to provide properly sized ﬂ ame. Turn in a clockwise direction to reduce the gas ﬂ ow.

Check Pressure Readings:

Inlet pressure can be checked by turning screw (A) counterclockwise 2 or 3 turns and then placing pressure gauge tubing over the test point. Gauge should read as described on the chart below. Check pressure with main burner operating on “HI”.

Outlet pressure can be checked the same as above using screw (B). Gauge should read as described on the chart below. Check

36

pressure with main burner operating on “HI”.

After taking pressure readings, be sure to turn screws clockwise ﬁ rmly to reseal. Do not overtorque.

Leak test with a soap and water solution.

W415-2207 / B / 02.05.18

A

B

INSERT PILOT ASSEMBLY

PILOT SCREW

It’s important to periodically perform a visual check of

ADD IMAGE

Adjust the pilot screw to provide properly sized ﬂ ame. Turn in a clockwise direction to reduce the gas ﬂ ow.

Check Pressure Readings:

Inlet pressure can be checked by turning screw (A) counter- clockwise 2 or 3 turns and then placing pressure gauge tubing over the test point. Gauge should read as described on the chart below. Check pressure with main burner operating on “HI”.

Outlet pressure can be checked the same as above using screw (B). Gauge should read as described on the chart below. Check pressure with main burner operating on “HI”.

After taking pressure readings, be sure to turn screws clockwise ﬁ rmly to reseal. Do not overtorque.

Leak test with a soap and water solution.

INSERT PILOT ASSEMBLY

*Maximum inlet pressure not to exceed 13”

adjustment

Prior to pilot adjustment, ensure that the pilot assembly has not been painted. If overspray or painting of the pilot assembly has occurred remove the paint from the pilot assembly, or replace. Fine emery cloth or a synthetic scrub pad (such as Scotch-Brite™) can be used to remove the paint from the pilot hood, electrode and ﬂ ame sensor.

EN

Pressure Natural Gas

(inches)

Inlet

Outlet

*7”

(minimum 4.5”)

3.5” 8.7mb 10” 24.9mb

8.4 ﬂame characteristics

the pilot and burner ﬂames. Compare them to the illustration provided. If any ﬂames appear abnormal, call a service person.

Natural Gas

(millibars)

17.4mb

(minimum 11.2mb)

SPARK MODULE

Propane

(inches)

13”

(minimum 11”)

FLAME SENSOR

Propane

(millibars)

32.4mb

(minimum 27.4mb)

PILOT BURNER

FLAME MUST ENVELOP UPPER 3/8” (9.5mm) TO 1/2” (12.7mm) OF FLAME SENSOR

W415-2207 / B / 02.05.18

37

WARNING

EN

9.0 maintenance

!

• Turn off the gas and electrical power before servicing the appliance.

• Appliance may be hot. Do not service until appliance has cooled.

• Do not use abrasive cleaners on glass.

• Do not paint the pilot assembly. This appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed

service person. The following suggested checks should be performed by a qualiﬁ ed technician. The appliance area must be kept clear and free of combustible materials, gasoline, or other ﬂ ammable vapors and liquids. The ﬂ ow of combustion and ventilation air must not be obstructed.

note:

Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

1. In order to properly clean the burner and pilot assembly, remove the logs, rocks and/or glass to ex-

pose both assemblies.

2. Keep the control compartment, media, burner, air shutter opening and the area surrounding the appli-

ance clean by vacuuming or brushing, at least once a year.

3. Check to see that all burner ports are burning. Clean out any of the ports which may not be burning

or are not burning properly.

4. Check to see that the pilot ﬂ ame is large enough to engulf the ﬂ ame sensor and/or thermocouple /

thermopile as well as it reaches the burner.

5. If your appliance is equipped with a safety barrier, cleaning may be necessary due to excessive lint /

dust from carpeting, pets, etc. simply vacuum using the brush attachment.

6. If your appliance is equipped with relief doors, ensure the system performs effectively. Check that the

gasket is not worn or damaged. Replace if necessary.

7. Replace the cleaned logs, rocks or glass. Failure to properly position the media may cause carboning

which can be distributed in the surrounding living area, inside the ﬁ rebox and on exterior surfaces surrounding vent termination.

8. Check to see that the main burner ignites completely on all ports when turned on. A 5 to 10 second

total light-up period is satisfactory. If ignition takes longer, consult your local authorized dealer / distributor.

9. Visually inspect the appliance for carbon build up. Using a small whisk or brush, brush off the carbon

and vacuum up or sweep into garbage.

10. This step is not applicable for Vent Free appliances: Check to see that the appliance is vent-

ing correctly. Ensure chimney system is safe and unobstructed. (If for any reason the vent air intake system is disassembled, re-install and re-seal per the instructions provided for the initial installation).

38

W415-2207 / B / 02.05.18

WARNING

maintenance

9.1 annual maintenance

!

• Annual maintenance should be performed by a qualiﬁ ed service technician

• The ﬁ rebox becomes very hot during operation. Let the appliance cool completely or wear heat resistant gloves before conducting service.

• Never vacuum hot embers.

• Do not paint the pilot assembly

• This appliance will require maintenance which should be planned on an annual basis.

• Service should include cleaning, battery replacement, venting inspection and inspection of the burner, media, and ﬁ rebox. Refer to the door removal section and remove the door as instructed.

• Carefully remove media if necessary (logs, glass, brick panels, etc.).

• Using a vacuum with soft brush attachment, gently remove any dirt, debris, or carbon build up from the logs, ﬁ rebox, and burner. For glass media, follow the installation instructions for pre-cleaning.

• Gently remove any build-up on the pilot assembly including thermopile, thermocouple, ﬂ ame sensor, and igniter (if equipped).

note:

Clean ﬂ ame sensor using a ﬁ ne emery cloth or a synthetic scrub pad (such as Scotch-Brite™) to remove any oxides. Clean the pilot assembly using a vacuum with a soft brush attachment. It is important that the pilot assembly is not painted.

EN

• Inspect all accessible gaskets and replace as required.

• If equipped with a blower, access the blower and clean using a soft brush and vacuum.

• Re-assemble the various components in reverse order.

• Inspect the relief system. The appliance relieves through the main glass door or through the ﬂ aps on the ﬁ rebox top. Ensure they open freely, and close sealed.

• Check the gas control valve pilot and Hi / Lo knobs move freely, if equipped. Replace if any stiffness in movement is experienced.

• Check for gas leaks on all gas connections up and downstream from the gas valve including pilot tube connections.

W415-2207 / B / 02.05.18

39

GASKET

GLASS LENS

GASKET

SHEILD

RAIL

WIRE NUT

COVER PLATE

RELIEF

DOOR

35

EN

37.1C

35

EN

maintenance

9.2 night light replacement

This appliance comes equipped with our “Night Light”. If in the event the lamp or lens needs to be replaced, follow these instructions. Disconnect the two wire leads at the wire nut. Remove the four screws securing the accent light assembly from the relief door. Disassemble the light and the lamp now can be accessed

WIRE NUT

note:

Do not handle the lamp (bulb) with bare ﬁngers. Protect with a clean, dry cloth.

The lamp will pull straight out of the socket. Replace with Wolf Steel parts only, as lamp and lens are special “high temperature” products. When re-installing, ensure integrity of gasket seal.

THE FIREBOX MUST BE SEALED.

RAIL

When re-assembling the light assembly, care must be taken with all gaskets.

“Light Leakage” from above the cast doors may be noticed. The holes in the lamp housing are necessary for ventilation and must not be covered.

9.3 pilot injector and oriﬁce replacement

WARNING

!

• Always light the pilot whether for the ﬁrst time or if the gas supply has run out with the glass door open or removed.

This must be carried out by an AUTHORIZED REPRESENTATIVE OF WOLF STEEL LTD. or a QUALIFIED GAS INSTALLER in accordance with local codes or in the absence of local codes with the requirements of the provincial / state authorities having jurisdiction and in accordance with the requirements of the CAN1-B149 Installation Code in Canada and the ANSI Z223.1 National Fuel Gas Code in the United States.

SHIELD

SHEILD

COVER PLATE

GASKET

GLASS LENS

GASKET

RELIEF

DOOR

RAIL

40

A. Turn off the electrical and gas supply to the appliance. B. Remove the cast front, glass viewing door and log set. C. Remove the 2 securing screws. Slide the burner assembly to the right and lift out. D. Using a deep socket wrench, remove the main burner oriﬁce. A back-up wrench

must be used on themanifold, located below the housing to ensure that the aluminum tubing does not twist or kink. Replace the correct burner oriﬁce using pipe thread compound.

E. Loosen nut and replace with appropriate injector F. Reinstall the burner ensuring that the Venturi tube ﬁts over the oriﬁce. G. Turn on the gas supply and check for gas leaks by brushing on a soap and water

solution. Do not use open ﬂame.

H. Replace the log set. Then light the pilot and main burner to ensure that the gas

lines have been purged.

I. Replace the glass viewing door and cast front. Turn on the electrical supply to the

appliance.

W415-2207 / B / 02.05.18

ORIFICE

LOCATION

BURNER

ASSEMBLY

!

WARNING

If the appliance is equipped with plated parts, you must clean ﬁ ngerprints or other marks from the plated surfaces

9.4 care of glass

• Do not clean glass when hot! Do not use abrasive cleaners to clean glass.

Buff lightly with a clean dry soft cloth to remove accumulated dust or ﬁ ngerprints. Clean both sides of the glass after the ﬁ rst 10 hours of operation with an ammonia-free glass cleaner.

note:

Vinegar-based glass cleaners have demonstrated an ability to provide a clean, streak free glass surface.

Thereafter, clean as required. If the glass is not kept clean permanent discoloration and / or blemishes may result. Contact you local authorized dealer / distributor for complete cleaning instructions.

Razor blades, steel wool, or other metallic objects must not be used on both surfaces of the glass. Doing so can remove a thin layer of metal from the razor blades, steel wool, or other metallic objects that may then be deposited onto the coating. This can result in a discoloured stain or scratch-like mark. More importantly, this can scratch the glass surface, thereby reducing its strength.

Do not operate the appliance with broken glass, as leakage of ﬂ ue gases may result. Contact your local authorized dealer / distributor for complete cleaning instructions. If the glass should ever crack or break while the ﬁ re is burning, do not open the door until the ﬁ re is out. Do not

operate the appliance until the glass has been replaced. Contact you local authorized dealer / distributor for replacement parts. DO NOT SUBSTITUTE MATERIALS.

This appliance is factory equipped with 5mm ceramic glass. Use only replacement parts as supplied by the appliance manufacturer. DO NOT SUBSTITUTE MATERIALS.

maintenance

EN

9.5 care of plated parts

before operating the appliance for the ﬁ rst time. Use an ammonia-free or vinegar-based cleaner and a towel to clean. If not cleaned properly before operating for the ﬁ rst time, the marks can cause permanent blemishes on the plating. After the plating is cured, the ﬁ ngerprints and oils will not affect the ﬁ nish and little maintenance is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause discolouration on plated parts.

note:

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can be improved if the assembly is warmed (i.e. using a hair dryer or similar heat source).

W415-2207 / B / 02.05.18

41

WARNING

Parts identiﬁ ed as ‘SO’ are special order and can take up to 90 days for delivery

EN

10.0 replacements

!

• Failure to position the parts in accordance with this manual or failure to use only parts speciﬁ cally approved with this appliance may result in property damage or personal injury.

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can be ordered through your Authorized dealer / distributor.

For warranty replacement parts, a photocopy of the original invoice will be required to honour the claim.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

Parts, part numbers, and availability are subject to change without notice. Parts identiﬁ ed as stocked will be delivered within 2 to 5 business days for most delivery

destinations. Parts not identiﬁ ed as stocked will be delivered within a 2 to 4 week period, for most cases.

42

W415-2207 / B / 02.05.18

Items may not appear exactly as illustrated.

Safety Barrier

4

5

10

11

14

19

Part No.

Ref. No.

W135-0254

W135-0249

W135-0250

GL-651

W385-2010

W135-0580

W010-3295

W010-1379

1115161819

W010-4177

W350-0655

141213 Front casting

Safety barrier

Door assembly

Rear log (GL-651)

Left log (GL-651)

Right log (GL-651)

Top casting

X2

Yes

17

replacements

Yes

EN

10.1 overview

Yes

3

1

2

W415-2207 / B / 02.05.18

43

Items may not appear exactly as illustrated.

Description

Ref. No.

Description

12

W456-0043

13

Stocked

11

Battery housing

151516

W725-0046

Gas valve shut-off

14

Valve (P)

17

18

Pro 2 wire harness

W750-0268

W660-0126-SER

Pro 2 transmitter

9

W432-0078

3/8" manifold

19

3

5

8

10

111412

15

16

19

W750-0411

Valve (NG)

W707-0019

Transformer

W456-0054

Yes

10

Yes

W456-0055

Burner oriﬁce #44 (NG) (high altitude)

W456-0044

Yes

EN

0

7

67°

Yes

44

10.2 valve train assembly

W415-2207 / B / 02.05.18

5

1

3

4

Ref. No.

1

4

GDSLL-KT

Leg leveling / stove securing kit

accessories

A stone inset can be cut to enhance the cast

top and to match the room décor. A template

is available to be downloaded from the

porduct website. Use this to cut the stone

slab to size so that it will ﬁt into the cast

recess.

EN

11.0 accessories

W415-2207 / B / 02.05.18

45

WARNING

EN

12.0 troubleshooting

!

• Always light the pilot whether for the ﬁ rst time or if the gas supply has run out, with the glass door open or removed.

• Turn off gas and electrical power before servicing the appliance.

• Appliance may be hot. Do not service until appliance has cooled.

• Do not use abrasive cleaners

symptom problem test solution

Main burner ﬂ ame is a blue, lazy, transparent ﬂ ame.

(This is not applicable in outdoor appliances)

Flames are consistently too large or too small. Carboning occurs.

INSERT

Blockage in vent. - Remove blockage. In really cold conditions, ice buildup may occur

Incorrect installation. - Refer to “venting” section to ensure correct installation.

Appliance is over-ﬁ red or underﬁ red.

on the terminal and should be removed as required. (To minimize this from reoccuring, the vent lengths that pass through unheated spaces (attics, garages, crawl spaces) be wrapped with an insulated mylar sleeve).

- Check pressure readings:

Inlet pressure can be checked by turning screw (A) counter-clockwise 2 or 3 turns and then placing pressure gauge tubing over the test point. Gauge should read as described on the chart below. Check that main burner is operating on ‘HI’. Outlet pressure can be checked the same as above using screw (B). Gauge should read as described on the chart below. Check that main burner is operating on ‘HI’. After taking pressure readings, be sure to turn screws

clockwise ﬁ rmly to reseal. DO NOT OVER TORQUE.

Leak test with a soap and water solution.

PHOTO

OF VALVE

HERE

Pressure Natural Gas

Inlet

Outlet

(inches)

*7”

(minimum 4.5”)

3.5” 8.7mb 10” 24.9mb

Natural Gas

(millibars)

17.4mb

(minimum 11.2mb)

*Maximum inlet pressure not to exceed 13”

Propane

(inches)

13”

(minimum 11”)

Propane

(millibars)

32.4mb

(minimum 27.4mb)

46

Air shutter improperly adjusted.

Carbon is being deposited on glass, logs, rocks, media, or combustion chamber surfaces.

White / grey ﬁ lm forms. Sulphur from fuel is being depos-

Exhaust fumes smelled in room, headaches.

W415-2207 / B / 02.05.18

Air shutter is blocked. - Ensure air shutter opening is free of lint or other obstructions.

Flame is impinging on the glass, logs, rocks, media or combustion chamber.

ited on glass, logs, or combustion chamber surfaces.

Appliance is spilling. (This is not applicable in outdoor appliances).

- Return air shutter to speciﬁ ed opening, see “venturi adjustments”

section in the installation manual.

- Ensure the media is positioned correctly in the appliance.

- Open air shutter to increase the primary air.

- Check the input rate: check the manifold pressure and oriﬁ ce size as speciﬁ ed by the rating plate.

- Ensure door gaskets are not broken or missing and the seal is tight.

- Ensure vent liners are free of holes and well sealed at all joints.

- Check that minimum rise per foot (meters) has been adhered to for any horizontal venting.

- Clean the glass with a recommended gas ﬁ replace glass cleaner. DO

NOT CLEAN GLASS WHEN HOT.

- If deposits are not cleaned off regularly, the glass may become permanently marked.

- Check door seal.

- Check for exhaust damage.

- Check that venting is installed correctly.

- Room is in negative pressure; increase fresh air supply.

Exhaust fumes smelled in room, headaches.

Appliance is spilling. (This is not applicable in outdoor appliances).

- Check door seal.

- Check for exhaust damage.

- Check that venting is installed correctly.

- Room is in negative pressure; increase fresh air supply.

Valve wiring is damaged. - Replace valve.

symptom problem test solution

Pilot will not light. Makes noise with no spark at pilot burner.

Pilot sparks but will not light.

Burner continues to spark and pilot lights but main burner does not light.

Remote wall switch is in “off” position; burner comes on.

Remote and / or receiver is not functioning properly.

Wiring: short, loose, or damaged connections (poor ﬂ ame rectiﬁ cation).

No signal from remote with no pilot ignition.

Poor grounding. - Verify the valve and pilot assembly is properly grounded

Improper switch wiring.

Dirty, painted, or damaged pilot and/or dirty sensor rod.

- Verify the thermocouple/sensor is clean and the wiring is undamaged.

- Verify the interrupter block is not damaged or too tight. Verify connections from pilot assembly are tight; also verify the connections are not grounding out to any metal. (Remember, the ﬂ ame carries the rectiﬁ cation current, not the gas. If ﬂ ame lifts from pilot hood, the circuit is broken. A wrong oriﬁ ce or too high of an inlet pressure can cause the pilot ﬂ ame to lift)*. The sensor rod may need cleaning.

- Reprogram receiver code.

- Replace receiver.

- Troubleshoot the system with the simplest on/off switch.

- Clean sensor rod with a green Scotch-Brite™ pad to remove any contamination that may have accumulated. Verify continuity with multimeter with ohms set at the lowest range.

Gas supply. - Verify that the incoming gas line ball valve is “open”.

- Verify that the inlet pressure reading is within acceptable limits, inlet pressures must not exceed 14” W.C. (34.9mb).

Out of propane gas. - Fill the tank.

Pilot supply line may contain air.

- Repeat ignition process several times or purge the pilot supply line.

Incorrect wiring / grounding. - Ensure correct polarity of wiring of thermocouple (if

equipped).

- Verify pilot assembly/valve are properly grounded.

Receiver (if equipped). - Reset program: hold reset button on receiver and wait for 2

beeps. Release after second beep. Press small ﬂ ame button on remote within 20 seconds, you will hear an additional beep (this signals a successful reset).

- Replace receiver.

Valve. - Check valve and replace if necessary (Do not to overtighten

thermocouple).

Short or loose connection in sensor rod.

- Verify all connections. Verify the connections from the pilot assembly are tight. Also, verify these connections are not grounding out to any metal.

Dirty, painted, or damaged pilot assembly components.

- Clean using a green Scotch-Brite™ pad to remove any contamination that may have accumulated on the sensor rod, pilot hood, ignitor, or ﬂ ame sensor. Verify continuity with multimeter with ohms set at the lowest range.

Wall switch mounted upside

- Reverse.

down.

Remote wall switch and/or wire is grounding.

- Replace.

- Check for ground (short); repair ground or replace wire.

Faulty wire - Replace.

Remote controls lights but no spark or ﬂ ame. (Remote is locked out).

- Reset by turning power source off then on.

note:

If back up batteries are installed, they must also be removed to re-program

troubleshooting

EN

Receiver or remote has low battery.

Appliance functions but does not respond to receiver / remote

Error with synchronizing. - Reset receiver and remote.

Remote too far away from receiver.

Wire connector pins are bent. - Straighten pins.

- Replace batteries.

- Ensure appliance is being operated by the same device that turned it on. Remote controls functions if appliance was turned on by remote. Receive controls functions if appliance was turned on by receiver.

- Refer to “wiring diagram” section.

W415-2207 / B / 02.05.18

47

rod, pilot hood, ignitor, or ﬂ ame sensor. Verify continuity with multimeter with ohms set at the lowest range.

Remote wall switch is in “off” position; burner comes on.

Wall switch mounted upside down.

- Reverse.

Remote wall switch and/or wire is grounding.

- Replace.

- Check for ground (short); repair ground or replace wire.

Faulty wire - Replace.

Remote and / or receiver is not functioning properly.

Remote controls lights but no spark or ﬂ ame. (Remote is locked out).

- Reset by turning power source off then on.

Receiver or remote has low battery.

- Replace batteries.

Appliance functions but does not respond to receiver / remote

- Ensure appliance is being operated by the same device that turned it on. Remote controls functions if appliance was turned on by remote. Receive controls functions if appliance was turned on by receiver.

Error with synchronizing. - Reset receiver and remote.

Remote too far away from receiver.

- Refer to “wiring diagram” section.

Wire connector pins are bent. - Straighten pins.

Valve wiring is damaged. - Replace valve.

If back up batteries are installed, they must also be removed to re-program

note:

EN

troubleshooting

Motor is turning, frequent beeping occurs.

Lights or blower won’t function (if equipped).

Flames are very aggressive.

Appliance won’t perform any functions.

symptom problem test solution

Receiver batteries low. - Replace batteries.

Control module switch in wrong position.

COM switch is unplugged. - Verify “COM” switch is plugged into the front of the control

Door is ajar. - Ensure door is secured properly.

Venting action is too great. - Check to ensure venting is properly sealed or restrict vent

No power to the system.

Receiver switch in wrong position (if equipped).

Transmitter isn’t operational. - Check battery power and battery orientation.

- Verify ON/OFF switch is in the “I” position which denotes on.

module.

exit with restrictor plate. (Not available in all appliances).

- Check breaker to verify it’s in the “on” position.

- Verify that the 3 position switch on the receiver is in the remote position (middle).

symptom problem test solution

The following applies speciﬁ cally to the SIT system only:

Pilot will not light. Makes no noise with no spark at pilot burner. (Lights and blower operate, if equipped).

note:

Starting from off, press the on button on the transmitter. Approximately 4 seconds on/off button is pressed, the ignition board will start the spark. The ﬁ rst try for ignition will last approximately 60 seconds. If there is no ﬂ ame ignition (rectiﬁ cation), the board will stop sparking for approximately 35 seconds. After the wait time, the board will start the second try for ignition by sparking for approximately 60 seconds. If there is still no positive ignition, the board will go into lock out.

Ignition box has been locked out.

Choose one of the 4 methods below to reset the system.

1. To reset ignition box when locked out. Turn off power supply

and remove batteries (if used) from the back up battery pack.

2. To reset the DFC Board when the board goes into a lock

out condition and the LED is blinking 3 times using the transmitter on/off button:

Step 1: Turn the system off by pressing the on/off button to turn the system off.

Step 2: After approximately 2 seconds press the on/ off button on the transmitter again. The DFC Board will

reset and the ignition sequence will start again.

3. To reset the DFC Board when the board goes into a lock out

condition and the LED is blinking 3 times by cycling ﬂ ame:

Step 1: In the manual ﬂ ame control mode, use the down arrow button to reduce the ﬂ ame to off, indicated by the word OFF displayed on the transmitter LCD screen. Step 2: Wait approximately 2 seconds and press the up arrow button, the ignition sequence will start.

48

W415-2207 / B / 02.05.18

13.0 warranty

trademark of Wolf Steel Ltd.

Napoleon products are manufactured under the strict Standard of the world recognized ISO 9001 : 2015 Quality Management

Napoleon products are designed with superior components and materials assembled by trained craftsmen who take great

pride in their work. The burner and valve assembly are leak and test-ﬁ red at a quality test station. The complete appliance is

again thoroughly inspected by a qualiﬁ ed technician before packaging to ensure that you, the customer, receives the quality

The following materials and workmanship in your new Napoleon gas appliance are warranted against defects for as long as you own the appliance. This covers: combustion chamber, heat exchanger, stainless / steel burner, Phazer™ logs and embers, rocks, ceramic glass (thermal breakage only), gold plated parts against tarnishing, porcelainized enameled components and aluminum extrusion trims.* Electrical (110V and millivolt) components and wearable parts are covered and Napoleon will provide replacement parts free of charge during the ﬁ rst year of the limited warranty. This covers: blowers, gas valves, thermal switches, switches, wiring, remote controls, ignitors, gaskets and pilot assemblies.* Labour related to warranty repair is covered free of charge during the ﬁ rst year (labour warranty is not applicable for the

Gas Log Sets). Repair work, however, requires the prior approval of an authorized company ofﬁ cial. Labour costs to the

account of Napoleon are based on a predetermined rate schedule and any repair work must be done through an authorized Napoleon dealer. * Construction of models vary. Warranty applies only to components included with your speciﬁ c appliance.

Napoleon warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary. Simply provide your proof of purchase along with the model and serial number to make a warranty claim. Napoleon reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the purchase was made through an authorized Napoleon dealer your appliance is subject to the following conditions and limitations: Warranty coverage begins on the date of original installation. This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives. The gas appliance must be installed by a licensed, authorized service technician or contractor qualiﬁ ed and authorized installer, service agency or supplier. Installation must be done in accordance with the installation instructions included with the product and all local and national building and ﬁ re codes. This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect, and parts installed from other manufacturers will nullify this warranty. This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and chemical cleaners nor chipping on porcelain enamel parts, mechanical breakage of Phazer™ logs and embers. This warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the product has been operated in accordance with the operation instructions and under normal conditions. After the ﬁ rst year, with respect to this President’s Lifetime Limited Warranty, Napoleon may, at its discretion, fully discharge all obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defective part(s).

System.

product that you expect from Napoleon.

Napoleon Gas Appliance President’s Lifetime Limited Warranty

Conditions and Limitations

EN

Napoleon will not be responsible for installation, labour, or any other expenses related to the reinstallation of a warranted part and such expenses are not covered by this warranty. Notwithstanding any provisions contained in the President’s Lifetime Limited Warranty, Napoleon’s responsibility under this warranty is deﬁ ned as above and it shall not in any event extend to any incidental, consequential or indirect damages. This warranty deﬁ nes the obligations and liability of Napoleon with respect to the Napoleon gas appliance and any other warranties expressed or implied with respect to this product, its components or accessories are excluded. Napoleon neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product. Napoleon will not be responsible for: over-ﬁ ring, downdrafts, spillage caused by environmental conditions such as rooftops, buildings, nearby trees, hills, mountains, inadequate vents or ventilation, excessive venting conﬁ gurations, insufﬁ cient makeup air, or negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc. Any damages to the appliance, combustion chamber, heat exchanger, plated trim or other components due to water, weather damage, long periods of dampness, condensation, damaging chemicals or cleaners will not be the responsibility of Napoleon. All parts replaced under the President’s Limited Lifetime Warranty Policy are subject to a single claim.

During the ﬁ rst 10 years Napoleon will replace or repair the defective parts covered by the lifetime warranty at our discretion free of charge. From 10 years to life, Napoleon will provide replacement parts at 50% of the current retail price. All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation. The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim. Returned products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will repair or replace such defect. Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any merchandise shipped without authorization will be refused and returned to sender. Shipping costs are not covered under this warranty. Additional service fees may apply if you are seeking warranty service from a dealer. Warranty labour allowance is only for the replacement of the warranted part. Travel, diagnostic tests, shipping and other related charges are not covered by this warranty.

All speciﬁ cations and designed are subject to change without prior notice due to on-going product improvements. Napoleon is a registered

W415-2207 / B / 02.05.18

49

NAPOLEON CELEBRATING OVER 40 YEARS OF HOME COMFORT PRODUCTS

Products

®

Other Napoleon

Fireplace Inserts • Charcoal Grills • Gas Fireplaces • Waterfalls • Wood Stoves Heating & Cooling • Electric Fireplaces • Outdoor Fireplaces • Gas Grills

24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8 103 Miller Drive, Crittenden, Kentucky, USA 41030

7200, Route Transcanadienne, Montréal, Québec H4T 1A3

7200 Trans Canada Highway, Montreal, Quebec, Canada H4T 1A3

24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8 103 Miller Drive, Crittenden, Kentucky, USA 41030

Fireplaces / Heating & Cooling call: 705-721-1212 • Grills call: 705-726-4278

napoleonproducts.com

Phone: 1-866-820-8686 napoleonproducts.com

MODÈLES DE GAZ NATUREL

MODÈLES DE PROPANE

GDS25N-1

GDS25P-1

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

FRANÇAIS

MANUEL D’INSTALLATION

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT!

RISQUE D’INCENDIE OU D’EXPLOSION

Incapacité à suivre ces avertissements exactement peuvent entraîner de grave blessures, des pertes de vie ou des dommages matériels.

- N’entreposez pas et n’utilisez pas d’essence ou autres liquides et vapeurs inﬂ ammables à proximité de cet appareil ou tout autre appareil.

- QUE FAIRE SI VOUS DÉTECTEZ UN ODEUR DE GAZ:

• N’allumez aucun appareil.

• Ne touchez à aucun interrupteur électrique; n’utilisez aucun téléphone dans votre immeuble.

• Appelez immédiatement votre fournisseur de gaz d’un téléphone voisin. Suivez ses instructions.

• Si vous ne pouvez pas rejoindre votre fournisseur de gaz, appelez le service des incendies.

- L’installation et l’entretien doivent être faits par

un installateur qualiﬁ é, une agence d’entretien ou le fournisseur.

ADD MANUAL TITLE

ET D’OPÉRATION

PRODUCT NAME™

Bayﬁeld™

ADD ____ ILLUSTRATED

ÉCRAN DE PROTECTION

ADD PRODUCT IMAGE

Cet appareil peut être installé dans une maison préfabriquée (mobile) déjà installée à demeure si les règlements locaux le permettent.

Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque d’homologation. Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilisée.

INSTALLATEUR:

Laissez ce manual avec l’appareil

PROPRIÉTAIRE:

Conservez ce manuel pour consultation

ultérieure

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Téléphone 1(866)820-8686 • www.napoleonfoyers.com • hearth@napoleonproducts.com

$10.00

POUR USAGE INTÉRIEUR SEULEMENT

CERTIFIÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICANES:

CSA 2.22 ET ANSI Z21.50 POUR LES APPAREILS À GAZ VENTILES DÉCORATIVES

CSA /

INTERTEK

LOGO

W415-2207 / B / 02.05.18

consignes de sécurité

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

AVERTISSEMENT

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

!

AVERTISSEMENT

FR

• Cet appareil est chaud lorsqu’il fonctionne et peut causer de graves brûlures en cas de contact.

• Toute modiﬁ cation apportée à cet appareil ou aux contrôles peut être dangereux et est interdit.

• Ne faites pas fonctionner l’appareil avant

d’avoir lu et compris les instructions d’opération. Omettre d’utiliser l’appareil selon les instructions d’opération pourrait causer un incendie ou des blessures.

• S’assurez que la porte vitrée est ouvert ou

retiré de l’appareil lorsque vous allumer le pilote pour la première fois et lorsque le gaz est épuisé

• Risque d’incendie ou d’asphyxie ne faites pas

fonctionner l’appareil avec la vitre retirée et jamais obstruer l’ouverture sur le devant de l’appareil.

• Les objets doivent être gardés à une distance d’au moins 4 pieds (1.22m) du devant de l’appareil.

• Ne branchez pas la soupape à du courant 110 volts, avec les exception de modèles; GSST8 et GT8.

• Risque de brûlures. L’appareil doit être éteint et refroidi avant d’effectuer un entretien.

• N’installez pas de composants endommagés ou incomplets ni des composants substituts.

• Risque de coupures et d’éraﬂ ures. Portez des gants protecteurs et des lunettes de sécurité lors de l’installation. Les bordures des pièces de métal peuvent être coupantes.

• Ne brûlez pas de bois ou autres matériaux dans cet appareil.

• Assurez-vous d’une quantité sufﬁ sante d’air de combustion et de ventilation. Prévoyez un accès sufﬁ sant

pour entretenir et opérer l’appareil. N’obstruez jamais l’ouverture sur le devant de l’appareil.

• L’appareil doit être gardé libre de tous matériaux combustibles, essence ou autres liquides et vapeurs inﬂ ammables.

• Haute pression endommagera la soupape. Débrancher la tuyauterie d’alimentation en gaz avant de tester la pression de ligne de gaz à la pression d’essai au-dessus de 1/2 psig. Fermer l’arrêt manuelle du soupape avant de tester la pression de ligne de gaz à la pression égale ou inférieure à 1/2psig (35mb).

• L’appareil ne doit pas être utilisé au températures au-dessous de zero (32°f / 0°c). Permettre à l’appareil pour réchauffer au-dessus de zero avant le fonctionnement, avec l’exception de modèles; GSS36, GSS42; ces appareil sont adaptés pour 0°F / -18°C.

• Les enfants et les adultes devraient être informés des dangers que posent les températures de surface élevées et se tenir à distance afin d’éviter des brûlures ou que leurs vêtements ne s’enflamment.

• Les jeunes enfants doivent être surveillés attentivement lorsqu’ils sont dans la même pièce que l’appareil. Les jeunes enfants et autres personnes à risque sont sujets aux brûlures accidentelles. Une barrière de protection est recommandée si des individus à risque se trouvent dans la maison. Aﬁ n de restreindre l’accès à l’appareil, installez une barrière de protection ajustable pour garder les jeunes enfants ou autres personnes à risque hors de la pièce et loin des surfaces chaudes.

• Les vêtements et autres matériaux combustibles ne doivent pas être posés sur l’appareil ou à proximité.

• En raison des températures élevées, l’appareil devrait être placé loin des endroits passants et loin des meubles et des rideaux.

• Les meubles ou autres objets doivent être gardés à une distance d’au moins 4 pieds (1.22m) du devant

de l’appareil.

• Assurez-vous de disposer de mesures de sécurité adéquates pour empêcher les jeunes enfants de toucher aux surfaces chaudes.

• Même une fois que l’appareil est éteint, la vitre et/ou le pare-étincelles demeureront chauds pendant un temps prolongé.

• Consultez votre détaillant local de foyer pour connaître les grillages de sécurité et les écrans offerts pour protéger les enfants des surfaces chaudes. Ces grillages de sécurité et ces écrans doivent être ﬁ xés au plancher.

!

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

Une barriére conçu à réduire le risque de brûlures causées par le verre chaud est fourni avec l’appareil et sera installé pour la protection des enfants et d’autres personnes à risque.

52

W415-2207 / B / 02.05.18

pour réchauffer au-dessus de zero avant le fonctionnement, avec l’exception de modèles; GSS36, GSS42; ces appareil sont adaptés pour 0°F / -18°C.

• Les enfants et les adultes devraient être informés des dangers que posent les températures de surface élevées et se tenir à distance afin d’éviter des brûlures ou que leurs vêtements ne s’enflamment.

• Les jeunes enfants doivent être surveillés attentivement lorsqu’ils sont dans la même pièce que l’appareil. Les jeunes enfants et autres personnes à risque sont sujets aux brûlures accidentelles. Une barrière de protection est recommandée si des individus à risque se trouvent dans la maison. Aﬁ n de restreindre l’accès à l’appareil, installez une barrière de protection ajustable pour garder les jeunes enfants ou autres personnes à risque hors de la pièce et loin des surfaces chaudes.

• Les vêtements et autres matériaux combustibles ne doivent pas être posés sur l’appareil ou à proximité.

• En raison des températures élevées, l’appareil devrait être placé loin des endroits passants et loin des meubles et des rideaux.

• Les meubles ou autres objets doivent être gardés à une distance d’au moins 4 pieds (1.22m) du devant

de l’appareil.

• Assurez-vous de disposer de mesures de sécurité adéquates pour empêcher les jeunes enfants de toucher aux surfaces chaudes.

• Même une fois que l’appareil est éteint, la vitre et/ou le pare-étincelles demeureront chauds pendant un temps prolongé.

• Consultez votre détaillant local de foyer pour connaître les grillages de sécurité et les écrans offerts pour protéger les enfants des surfaces chaudes. Ces grillages de sécurité et ces écrans doivent être ﬁ xés au plancher.

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

!

AVERTISSEMENT

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

Une barriére conçu à réduire le risque de brûlures causées par le verre chaud est fourni avec l’appareil et sera installé pour la protection des enfants et d’autres personnes à risque.

!

AVERTISSEMENT

!

AVERTISSEMENT

pour vous protéger, ainsi que votre famille, contre les intoxications.

• Tout écrans de sécurité, écrans ou barriére enlevés pour faire l’entretien devront être remis en place avant d’utiliser l’appareil.

• Il est primordial de garder propres les compartiments de contrôle, les brûleurs, la soufﬂ erie, les bouches d’air de l’appareil ainsi que le système d’évacuation. L’appareil et son système d’évacuation doivent être inspectés avant la première utilisation et au moins une fois l’an par un spécialiste en entretien. Un entretien plus fréquent pourrait être nécessaire en raison des peluches provenant des tapis, literie, etc. L’emplacement de l’appareil doit être gardé libre de tous matériaux combustibles, essence ou autres liquides et vapeurs inﬂ ammables.

• Si l’appareil s’éteint, n’allume pas l’appareil jusqu’à ce que vous donner de l’air frais. Si l’appareil continue de s’éteindre, faire réparer.

• Cet appareil ne devra être modiﬁ é en aucun cas.

• Ne laissez pas les ventilateurs soufﬂ er directement sur l’appareil. Empêchez les courants d’air de modiﬁ er l’apparence de la ﬂ amme.

• N’utilisez pas une soufﬂ erie intégrée, un échangeur de chaleur intégré ni un autre accessoire non

approuvé pour cet appareil.

• Cet appareil ne doit pas être raccordé au conduit d’une cheminée desservant un autre appareil de

chauffage à combustible solide.

• N’utilisez pas cet appareil si une partie quelconque a été submergée. Contactez immédiatement un technicien de service qualiﬁ é pour inspecter l’appareil et pour remplacer toute pièce du système de contrôle et du contrôle du gaz qui aurait été submergée.

• Ne pas opérer l’appareil lorsque la porte vitrée est enlevée, ﬁ ssurée ou brisée. Le remplacement de la vitre devra être effectué par un technicien de service certiﬁ é ou qualiﬁ é, si équippé.

• Ne frappez pas et ne claquez pas la porte vitrée de l’appareil, si équippé.

• Seulement les portes/façades certiﬁ ées pour l’appareil peuvent être utilisées avec cet appareil.

• Gardez les matériaux d’emballage hors de la portée des enfants et mettez ces matériaux au rebut de façon sécuritaire. Comme tous les emballages de plastique, ces matériaux ne sont pas des jouets et doivent demeurer hors de la portée des enfants et des bébés.

• Si équipé, l’écran doivent être fermez en place pendant le fonctionnement de l’appareil.

• Lorsque l’appareil est muni de portes d’évacuation de pression, elles doivent demeurer fermées pendant le fonctionnement de l’appareil aﬁ n d’empêcher les gaz de combustion contenant du monoxyde de carbone de s’inﬁ ltrer dans la maison. La température des gaz de combustion s’échappant par ces ouvertures peut aussi causer les matériaux combustibles avoisinants à surchauffer et à prendre feu.

• L’empoisonnement au monoxyde de carbone peut conduire à la mort; les premiers signes d’une intoxication au monoxyde de carbone ressemblent à la grippe, avec céphalées, vertiges et/ou des nausées. Si vous présentez ces signes, l’appareil peut ne pas fonctionner correctement. Obtenir l’air frais! Faire réparer l’appareil. Certaines personnes; les femmes enceintes, les personnes ayant une maladie cardiaque ou pulmonaire, anémie, ceux sous l’inﬂ uence de l’alcool, ceux à haute altitude sont plus touchées par le monoxyde de carbone que d’autres. Défaut de garder l’ouverture d’air primaire(s) du brûleur(s) propre peut entraîner la formation de suies et dommages à la propriété.

• Comme dans le cas de tout appareil à combustion, il est recommandé de faire inspecter et entretenir votre appareil régulièrement. De même, installez un détecteur de monoxyde de carbone dans la pièce

Garder propres le brûleur et le compartiment de contrôle.

consignes de sécurité

FR

W415-2207 / B / 02.05.18

53

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

!

AVERTISSEMENT

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

Une barriére conçu à réduire le risque de brûlures causées par le verre chaud est fourni avec l’appareil et sera installé pour la protection des enfants et d’autres personnes à risque.

!

AVERTISSEMENT

!

AVERTISSEMENT

L’emplacement de l’appareil doit être gardé libre de tous matériaux combustibles, essence ou autres liquides et vapeurs inﬂ ammables.