Napoleon B81NL, B81PL Installation And Operating Instructions Manual

Download

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS.

HD81

LOG BURNER

ASSEMBLY

B81NL

NATURAL GAS

B81PL

PROPANE

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

SAFETY INFORMATION

WARNING

If the information in these instructions are not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

- Installation and service must be performed by a

qualiﬁ ed installer, service agency or the supplier.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonﬁ replaces.com • ask@napoleonproducts.com

$10.00

1.22

W415-0713 / A / 11.09.10

TABLE OF CONTENTS

1.0 GENERAL INFORMATION 2

2.0 INSTALLATION 2

3.0 ADJUSTMENT 7

4.0 REPLACEMENTS 8

2.1 ACCESS PANEL 2

2.2 BURNER ASSEMBLY 2

2.3 BULKHEADS 3

2.4 NIGHT LIGHT™ INSTALLATION 4

2.5 HEARTH PANEL INSTALLATION 4

2.6 LOG PLACEMENT 5

2.7 CHARCOAL LUMPS 6

2.8 CHARCOAL EMBERS 6

2.9 VERMICULITE 7

2.10 GLOWING EMBERS 7

3.1 FLAME CHARACTERISTICS 7

3.2 VENTURI ADJUSTMENT 7

NOTE: Changes, other than editorial, are denoted by a line in the margin.

1.0 GENERAL INFORMATION

This burner and log assembly are approved for use in the HD81 gas appliance only. They are not approved for use as a stand alone appliance or in conjunction with any other appliance.

2.0 INSTALLATION

2.1 ACCESS PANEL

A. Once either door is removed (see

Installation Instructions), remove the valve access panel and the 4 retaining brackets located at the top of the ﬁ rebox.

2.2 BURNER ASSEMBLY

A. Attach the burner assembly to the ﬁ rebox

base with the screws supplied, making sure the pilot assembly is closest to the valve access opening.

Retaining

Brackets

Access

Panel

Valve

Access

Opening

Pilot

Assembly

W415-0713 / A / 11.09.10

Burner

Assembly

2.3 BULKHEADS

NOTE: Bulkhead covers need to be removed.

A. Connect the gas ﬂ ex lines and the pilot line

to the gas bulkheads located under the valve access opening. Be sure to match up the gas manifold marked with a green dot with the center bulkhead, also marked with a green dot. Care must be taken to ensure the pilot line isn’t damaged and ensuring gas tight connections are made.

B. Connect the pilot electrode leads to the

bulkhead matching the 1/4” ﬂ ag with the 1/4” bulkhead spade and the 3/16” ﬂ ag with the 3/16” spade.

C. Ensure the 2 venturi tubes are over the

oriﬁ ces before lighting.

D. Check for gas leaks by brushing on a soap

and water solution. Do not use open ﬂ ame.

E. After leak test has been performed re-install

access panel with gasket.

Bulkheads

See Thru Window

Green

Dots

Gas

Pilot

Bulkhead

Pilot

Electrode

Pilot

Electrode

Leads

Venturi

Tube

Oriﬁ ce

W415-0713 / A / 11.09.10

2.4 NIGHT LIGHT™ INSTALLATION

Your HD81 comes equipped with 2 “Night Lights™”. The lights have been pre-wired and are controlled from the remote control. Included with the burner assembly are the frames, lenses and gaskets that need to be installed as shown.

THE FIREBOX MUST BE SEALED.

Over tightening the screws could break the lens. “Light Leakage” from the holes in the housing lamp may be observed. The holes in the lamp housing are necessary for ventilation and must not be covered.

2.5 HEARTH PANEL INSTALLATION

Hearth panels are shipped separate from unit and are included with the burner assembly and the logs. Due to the brittle material of the panels, care must be taken not to bend or force them into place. When shipped, the hearth panels range in varying shades of Sandstone. During initial use, the panels will darken temporarily. The appearance of the panels will permanently lighten in color with use.

NIGHT LIGHT

COLOURED SIDE UP

GASKET

LENS

FRAME

INSTALL HEARTH PANELS IN THE FOLLOWING ORDER: NOTE: Burner assembly must be installed ﬁ rst.

A. Side brick panels or porcelain panels must be installed prior to

hearth panels. For brick panel installation see “GD844KT DECORA TIVE BRICK PANEL - SANDST ONE” leaﬂ et and PRP81 leaﬂ et for porcelain panel installation.

B. Install the left and right hearth panels on both sides.

HEARTH PANELS

W415-0713 / A / 11.09.10

2.6 LOG PLACEMENT

A. Place the left middle log #1 onto the

locating stud on the middle log support. Make sure the hollow on the underside of the log is over the bend tab.

B. Slide log #2 from right to left on the

middle log support creating a tight ﬁ t between logs #1 and #2. Make sure the hollow on the underside of the log is over the bend tab.

C. Place log #3 onto the far right locating

stud located on the front deﬂ ector.

E. Place log #5 onto the far left locating

stud located on the front deﬂ ector.

D. Place log #4 onto the two center

locating studs on the front support.

NOTCH

F. Place the notch on log #6 onto the third

grate.

W415-0713 / A / 11.09.10

G. Slide the ﬂ at portion of log #7 under the

second grate post.

NOTE: Logs 3, 4, 5, 6 and 7 are included twice. Install these logs on the opposite side. Logs 8 and 9 are only included once, to give a different appearance to each side. Install logs 8 and 9 on the side that you prefer. If desired a 2nd set of 8 and 9 logs are available in an upgrade kit GL81L2 and can be purchased to make both sides identical.

H. Place the pin in log #8 into the locating

hole on log #1 and rest the bottom of the log on log #5.

J. If GL81L2 (upgrade kit) is purchased repeat

“H” and “I” on other side.

I. Place the pin in log #9 into the locating

hole on log #2 and rest the bottom of the log #3.

2.7 CHARCOAL LUMPS

CHARCOAL EMBERS, VERMICULITE AND CHARCOAL LUMPS ARE NOT TO BE PLACED ON THE

Place the lumps in front of the logs in a realistic manner taking care not to block any of the burner ports.

2.8 CHARCOAL EMBERS

Randomly place the charcoal embers along the front and sides of the log support tray in a realistic manner.

Fine dust found in the bottom of the bag should not be used. NOTE: Charcoal embers are not to be placed on the burner.

WARNING

BURNER.

34.1

32.1

W415-0713 / A / 11.09.10

2.9 VERMICULITE

Sprinkle vermiculite around the charcoal embers.

NOTE: Vermiculite is not to be placed on the burner.

2.10 GLOWING EMBERS

Tear the embers into pieces and place along the front row of ports covering all of the burner area. Care should be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the ﬁ bre hairs will glow. The ember material will only glow when exposed to direct ﬂ ame; however, care should be taken to not block the burner ports. Blocked burner ports can cause an incorrect ﬂ ame pattern, carbon deposits and delayed ignition. Phazer™ logs glow when exposed to direct ﬂ ame. Use only certiﬁ ed “glowing embers” and Phazer™ logs available from your Authorized dealer.

3.0 ADJUSTMENT

3.1 FLAME CHARACTERISTICS

It’s important to periodically perform a visual check of the pilot and burner ﬂ ames. Compare them to the illustra- tions provided. If any ﬂ ames appear abnormal call a service person.

BURNER

ELECTRODE

PILOT

33.1

3/8” - 1/2”

3.2 VENTURI ADJUSTMENT

This appliance has an air shutter that has been factory set open according to the chart below:

Regardless of venturi orientation, closing the air shutter will cause a more yellow flame, but can lead to carboning. Opening the air shutter will cause a more blue flame, but can cause flame lifting from the burner ports. The flame may not appear yellow immediately; allow 15 to 30 minutes for the final flame color to be established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED INSTALLER!

FLAME

SENSOR

FLAME MUST ENVELOP UPPER 3/8” TO 1/2” OF FLAME SENSOR

54.1

VENTURI BURNER

AIR SHUTTER OPENING

ORIFICE

49.1

Air Shutter Openings both Burners

LP 7/16”

NG 3/16”

W415-0713 / A / 11.09.10

4.0 REPLACEMENTS

Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMA TION, CONTACT YOUR AUTHORIZED DEALER.

REF NO. PART NO. DESCRIPTION

1 W280-0071 NIGHT LIGHT LENS FRAME 2 W290-0080 NIGHT LIGHT GASKET 3 W300-0067 CERAMIC ORANGE NIGHT LIGHT LENS 4 W100-0107 RIGHT SIDE LOG BURNER 4 W100-0108 LEFT SIDE LOG BURNER 5* W175-0227 CONNECTOR, 3/8” STAINLESS STEEL FLEX 6* W175-0289 CONNECTOR, 3/8” STAINLESS STEEL FLEX (24”) 7 W010-1829 3-WAY NATURAL GAS PILOT ASSEMBLY 7 W010-1830 3-WAY PROPANE GAS PILOT ASSEMBLY 8 W456-0033 #33 ORIFICE NATURAL 8 W456-0053 #53 ORIFICE PROPANE 9 W455-0070 NATURAL GAS PILOT INJECTOR 9 W455-0065 PROPANE GAS PILOT INJECTOR 10 GL-666 LOG SET 11 W135-0366 LOG, RIGHT MIDDLE #2 12 W135-0367 LOG, LEFT MIDDLE #1 13 W135-0368 LOG, RIGHT FRONT #3 14 W135-0369 LOG, LEFT FRONT #5 15 W135-0370 LOG, MIDDLE FRONT #4 16 W135-0371 LOG, RIGHT CROSSOVER 17 W135-0372 LOG, LEFT CROSSOVER 18 W135-0373 LOG, BOTTOM FRONT CROSSOVER 19 W135-0374 LOG, BOTTOM LEFT FRONT 20 W475-0574 HEARTH RIGHT FIBRE PANEL 21 W475-0613 HEARTH LEFT FIBRE PANEL 22* W361-0016 GLOWING EMBERS 23* W550-0001 CHARCOAL EMBERS 24* W550-0002 CHARCOAL LUMPS 25* W361-0014 VERMICULITE 26 W750-0200 FLAME SENSOR 27 W750-0201 ELECTRODE 28 W010-1946 ASSEMBLY, LOG GRATE

COMPONENTS

WARNING

FAILURE TO POSITION THE PARTS

IN ACCORDANCE WITH THIS

MANUAL OR FAILURE TO USE ONLY

PARTS SPECIFICALLY APPROVED

WITH THIS APPLIANCE MAY

RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY.

41.1

Installation and repairs must be performed by a qualiﬁ ed installer, service agency or the supplier.

W415-0713 / A / 11.09.10