Napoleon B42NTRE, B42NTR Installation Manual

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

SAFETY BARRIER

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE

INSTALLATION AND

OPERATING INSTRUCTIONS

CERTIFIED TO CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.22 AND ANSI Z21.50 FOR VENTED GAS FIREPLACES.

B42NTR / B42NTRE

FOR INDOOR USE ONLY

NATURAL GAS MODEL

FR PG 67

If the information in these instructions are not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

ﬁ re department.

- Installation and service must be performed by a qualiﬁ ed installer, service agency or the supplier.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a certiﬁ ed kit is used.

SAFETY INFORMATION

WARNING

B42PTR / B42PTRE

PROPANE GAS MODEL

DANGER

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonﬁ replaces.com • hearth@napoleonproducts.com

$10.00

1.28G

W415-1293 / E / 12.22.16

TABLE OF CONTENTS

NOTE: The camera icon indicates video tutorials are available as additional reference, visit http://mynapoleon.napoleonproducts.com/download/index/44/1

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

2.1 DIMENSIONS 5

2.2 GENERAL INSTRUCTIONS 6

2.3 GENERAL INFORMATION 7

2.4 RATING PLATE INFORMATION 8

3.0 VENTING 9

3.1 VENTING LENGTHS AND COMPONENTS 10

3.2 TYPICAL VENT INSTALLATION 11

3.3 SPECIAL VENT INSTALLATIONS 13

3.3.1 PERISCOPE TERMINATION 13

3.3.2 CORNER TERMINATION 13

3.4 MINIMUM AIR TERMINAL LOCATION CLEARANCES 14

3.5 VENTING APPLICATION FLOW CHART 15

3.6 DEFINITIONS 15

3.7 ELBOW VENT LENGTH VALUES 16

3.8 TOP EXIT HORIZONTAL TERMINATION 16

3.9 REAR EXIT HORIZONTAL TERMINATION 18

3.10 TOP AND REAR EXIT VERTICAL TERMINATION 20

3.11 REAR EXIT 22

3.12 REAR EXIT SHIELD (FOR REAR VENT ONLY) 22

3.13 TOP EXIT 23

4.0 INSTALLATION 24

4.1 WALL AND CEILING PROTECTION 24

4.1.2 HORIZONTAL INSTALLATION 25

4.1.1 VERTICAL INSTALLATION 25

4.2 USING FLEXIBLE VENT COMPONENTS 26

4.2.1 HORIZONTAL AIR TERMINAL INSTALLATION 26

4.2.2 VERTICAL AIR TERMINAL INSTALLATION 27

4.2.3 APPLIANCE VENT CONNECTION 28

4.3 USING RIGID VENT COMPONENTS 28

4.3.1 HORIZONTAL AIR TERMINAL INSTALLATION 28

4.3.2 VERTICAL AIR TERMINAL INSTALLATION 29

4.3.3 RESTRICTING VERTICAL VENTS 30

4.4 VERTICAL THROUGH EXISTING CHIMNEY 31

4.5 MOBILE HOME INSTALLATION 32

4.6 GAS INSTALLATION 32

4.7 OPTIONAL WALL SWITCH 33

5.0 FRAMING 33

5.1 MINIMUM FRAMING DIMENSIONS 34

5.2 MINIMUM ENCLOSURE CLEARANCES 36

5.3 NON-COMBUSTIBLE FACING MATERIAL 40

5.4 ALCOVE CLEARANCES 40

5.5 RECESSED INSTALLATION 41

5.6 MINIMUM MANTEL CLEARANCES 42

5.7 NAILING TAB INSTALLATION 42

6.0 FINISHING 43

6.1 SAFETY SCREEN / DOOR REMOVAL AND INSTALLATION 43

6.2 FRONT HOOD INSTALLATION 44

6.3 LOG PLACEMENT 45

6.4 GLOWING EMBERS 46

6.5 CHARCOAL EMBERS 46

6.6 LOGO PLACEMENT 46

6.7 BATTERY BACK-UP INSTALLATION 47

6.8 OPTIONAL (AUB) BLOWER INSTALLATION 48

7.0 WIRING DIAGRAM 49

7.1 ELECTRONIC WIRING DIAGRAM 49

8.0 OPERATION (ELECTRONIC) 50

9.0 OPERATION (MILLIVOLT) 51

10.0 ADJUSTMENT 52

10.1 PILOT BURNER ADJUSTMENT 52

10.2 VENTURI ADJUSTMENT 52

10.3 FLAME CHARACTERISTICS 53

10.4 OPTIONAL ANTI CONDENSATION SWITCH (MODELS B42NTRE AND B42PTRE ONLY) 53

11.0 MAINTENANCE 54

11.1 ANNUAL MAINTENANCE 54

11.2 DOOR GLASS REPLACEMENT 55

11.3 CARE OF GLASS 55

12.0 REPLACEMENTS 56

12.1 OVERVIEW 57

12.2 ELECTRONIC VALVE TRAIN ASSEMBLY 58

12.3 MILLIVOLT VALVE TRAIN ASSEMBLY 59

13.0 ACCESSORIES 60

14.0 TROUBLESHOOTING (ELECTRONIC) 61

15.0 TROUBLESHOOTING (MILLIVOLT) 63

16.0 WARRANTY 65

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

W415-1293 / E / 12.22.16

1.0 INSTALLATION OVERVIEW

“INSTALLATION”.

See the section “MINIMUM ENCLOSURE CLEARANCES” for drywall (or other combustible material).

See the section “MINIMUM MANTEL CLEARANCES”.

See the section “MINIMUM FRAMING DIMENSIONS”.

See the section “VENTING” and

See the section “FRAMING”.

Side Wall

See the section “RATING PLATE INFORMATION”.

SAFETY BARRIER

Batteries must be disposed of according to the local laws and regulations. Some batteries may be recycled, and may be accepted for disposal at your local recycling center. Check with your municipality for recycling instructions.

W415-1293 / E / 12.22.16

Installation and repair should be done by a qualiﬁ ed service person. The appliance should be inspected before use and

WARNING

2.0 INTRODUCTION

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND ARE PROHIBITED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause ﬁ re or injury.

• Risk of ﬁ re or asphyxiation do not operate appliance with ﬁ xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot

surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces. These

screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to operating the appliance.

• The appliance is a vented gas-ﬁ red appliance. Do not burn wood or other materials in the appliance.

• The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician to inspect the appliance

and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust fumes

containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these openings can also cause the surrounding combustible materials to overheat and catch ﬁ re.Only doors / optional fronts certiﬁ ed with the unit are to be installed on the appliance.

• Only doors / optional fronts certiﬁ ed with the unit are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these are not toys and should be kept away from children and infants.

• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures

on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V. or other electronic components.

• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be

installed.

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

•

at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

• The millivolt version of this appliance uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple supplied by Wolf Steel Ltd.

3.1E

W415-1293 / E / 12.22.16

2.1 DIMENSIONS

18 7/8"

480mm

178mm

102mm

613mm

24 1/8"

11 5/16"

288mm

GAS

42"

1067mm

INLET

7 3/16"

[ 182mm ]

[ 879mm ]

34 5/8"

465mm

18 5/16"

2 3/16"

56mm

SAFETY BARRIER

W415-1293 / E / 12.22.16

THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER

conform with local codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for example in Massachusetts State:

•

The installation must conform with local codes or, in absence of local codes, the National Gas and Propane Installation Code CSA B149.1 in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States. Suitable for mobile home installation if installed in accordance with the current standard CAN/CSA Z240MH Series, for gas equipped mobile homes, in Canada or ANSI Z223.1 and NFPA 54 in the United States.

As long as the required clearance to combustibles is maintained, the most desirable and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat created. The location of windows, doors and the trafﬁ c ﬂ ow in the room where the appliance is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or roof joist.

If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.

Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian

Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.

SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS

WARNING

2.2 GENERAL INSTRUCTIONS

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,

WITH THE GLASS DOOR OPENED OR REMOVED.

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

PROVIDE ADEQUATE VENTILATION.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48 INCHES

(121.9cm) FROM THE FRONT FACE OF THE APPLIANCE.

WHEN THE APPLIANCE IS OPERATING.

FIRE RISK. EXPLOSION HAZARD.

LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE

TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG (35mb).

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.

USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING

COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.

THE APPLIANCE MUST NOT BE OPERATED AT TEMPERATURES BELOW FREEZING (32°F / 0°C).

ALLOW THE APPLIANCE TO WARM TO ABOVE FREEZING PRIOR TO OPERATION.

This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of Massachusetts. The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas log. The appliance off valve must be a “T” handle gas cock. The ﬂ exible connector must not be longer than 3 feet (0.9m). A Carbon Monoxide detector is required in all rooms containing gas ﬁ red appliances. The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.

We suggest that our gas hearth products be installed and serviced by professionals

W415-1293 / E / 12.22.16

www.ncertied.org

who are certied in the U.S. by the National Fireplace

Institute

(NFI) as NFI Gas

Specialists

4.1C

2.3 GENERAL INFORMATION

FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND

Altitude (FT) 0-4,500 0-4,500

Max. Input (BTU/hr) 22,000 22,000

Min. Inlet Gas Supply Pressure 4.5" (11mb) Water Column 11" (27mb) Water Column

Max. Inlet Gas Supply Pressure 13" (32mb) Water Column 13" (32mb) Water Column

Manifold Pressure (Under Flow Conditions) 3.5" (9mb) Water Column 10" (25mb) Water Column

QUALITY!

RATES AND EFFICIENCIES

NG P

B42 MODEL DESIGNATIONS

FUEL TYPE OPERATING SYSTEM

B42NTR B42NTRE B42PTR B42PTRE

When the appliance is installed at elevations above 4,500 ft (1371m), and in the absence of speciﬁc recommendations from the local authority having jurisdiction, the certiﬁed high altitude input rating shall be reduced at the rate of 4% for each additional 1,000 ft (305m).

This appliance is approved for bathroom, bedroom, and bed-sitting room installations and is suitable for mobile home installation.

No external electricity (110 volts or 24 volts) is required for the gas millivolt system operation.

Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected.

NATURAL MILLIVOLT

NATURAL ELECTRONIC IGNITION PROPANE MILLIVOLT PROPANE ELECTRONIC IGNITION

W415-1293 / E / 12.22.16

SAMPLE

2.4 RATING PLATE INFORMATION

DIRECT VENT GAS FIREPLACE. SUITABLE FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONTRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A.

USE WITH BARRIER W565-0150. FOLLOW THE INSTALLATION INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL.

NOT FOR USE WITH SOLID FUEL. FOR USE WITH GLASS DOORS CERTIFIED WITH THIS UNIT ONLY.

WARNING: THIS FIREPLACE USES AND REQUIRES A FAST ACTING THERMOCOUPLE. REPLACE

ONLY WITH A FAST ACTING THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD. DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE. MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS / DEGAGEMENTS MINIMAUX DES MATERIAUX COMBUSTIBLES: TOP/ DESSUS 0 RECESSED DEPTH / PROFONDEUR D'ENCASTRE 18" FLOOR / PLANCHER 0 VENT SIDES / COTES DE L'EVENT 1" SIDES / COTES 0 VENT TOP / EVENT SUPERIEUR 3" BACK / ARRIERE 0 VENT BOTTOM / EVENT INFERIEUR 1" MANTEL / MANTEAU 2" * * MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION HORIZONTALE MAXIMALE: 2". SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS. REFERER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS PLUS GRANDES.

CONFORMS TO / CONFORME AUX: ANSI Z21.50-2014, CERTIFIED TO / CERTIFIE CSA 2.22-2014 VENTED GAS FIREPLACE / FOYER À GAZ VENTILÉ.

9700539 (WSL) 4001657 (NGZ) 4001658 (NAC) 4001659 (WUSA)

22,000 BTU/h INPUT / ALIMENTATION 22,000 BTU/h 17,300 BTU/h REDUCED INPUT / ALIMENTATION REDUITE 19,500 BTU/h

PRESSION AU COLLECTEUR: 3.5" (9 MB) D'UNE COLONNE D'EAU PRESSION AU COLLECTEUR: 10" (25MB) D'UNE COLONNE D'EAU MINIMUM SUPPLY PRESSURE: 4.5" (11MB) WATER COLUMN MINIMUM SUPPLY PRESSURE: 11" (27MB) WATER COLUMN PRESSION D'ALIMENTATION MINIMALE: 4.5" (11MB) D'UNE COLONNE D'EAU PRESSION D'ALIMENTATION MINIMALE: 11" (27MB) D'UNE COLONNE D'EAU MAXIMUM SUPPLY PRESSURE: 7.0" (17MB) WATER COLUMN MAXIMUM SUPPLY PRESSURE: 13" (32MB) WATER COLUMN PRESSION D'ALIMENTATION MAXIMALE: 7.0" (17MB) D'UNE COLONNE D'EAU PRESSION D'ALIMENTATION MAXIMALE: 13" (32MB) D'UNE COLONNE D'EAU P4: 65% P4: 65%

B42NTR CB42NTR MODEL CB42PTR B42PTR

MANIFOLD PRESSURE: 3.5" (9MB) WATER COLUMN MANIFOLD PRESSURE: 10" (25MB) WATER COLUMN

SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS. REFERER AU MANUEL D'INSTALLATION DE PROPRIETAIRE POUR LES LONGUEURS D'EVACUATION MINIMALE ET MAXIMALE.

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

B42NTRE CB42NTRE CB42PTRE B42PTRE

0-4500FT (0-1370m) ALTITUDE / ELEVATION 0-4500FT (0-1370m)

FOR

FOYER À GAZ VENTILÉ DIRECT. HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A COUCHER,

UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE POUR INSTALLATION DANS UNE MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU CANADA OU AUX ETATS-UNIS DE LA NORME DE SECURITE ET DE CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE REFERER A LA NORME RELATIVE AU CRITERE DE MESURES DE SECURITE CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURES, LES SITES ET LES COMMUNAUTES, ANSI/NFPA 501A.

AVEC BARRIÈRE W565-0150. SUIVEZ LES INSTRUCTIONS D'INSTALLATION SE TROUVENT DA NS LE MANUEL D'INSTALLATION.

UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE AVEC CET APPAREIL. UTILISER AVEC LES PORTES VITREES HOMOLOGUEES SEULEMENT AVEC CETTE UNITE.

AVERTISSEMENT: CE FOYER UTILISE ET REQUIERT UN THERMOCOUPLE À ACTION RAPIDE.

REMPLACEZ UNIQUEMENT AVEC UN THERMOCOUPLE À ACTION RAPIDE DE WOLF STEEL LTÉE. N’AJOUTEZ PAS A CET APPAREIL AUCUN MATERIAU DEVANT ENTRER EN CONTACT AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT. THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS. SEE OWNERS INSTALLATION MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR INTAKE SYSTEM. L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L'ENSEMBLE D'EVACUATION PROPRE A NAPOLEON. REFERER AU MANUEL D'INSTALLATION DE PROPRIETAIRE POUR L'EVACUATION PRECISE. IL EST IMPORTANT DE BIEN REINSTALLER ET RESCELLER L'EVENT APRES AVOIR ASSURE LE MAINTIEN DU SYSTEME DE PRISE D'AIR. DECORATIVE PRODUCT: NOT FOR USE AS A HEATING APPLIANCE PRODUIT DÉCORATIF: NE PAS UTILISER COMME APPPAREIL DE CHAUFFAGE. ELECTRICAL RATING / CLASSIFICATION: 115V 0.82AMP, 60HZ OPTIONAL FAN KIT / ENSEMBLE DE VENTILATEUR FACULTATIF: EP35

SERIAL NUMBER/NO. DE SERIE:

For rating plate location, see “INSTALLATION OVERVIEW” section.

B42

POUR UNE UTILISER

W385-2069

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

A barrier designed to reduce the risk of burns from the hot viewing glass, is provided with the appliance and shall be installed.

W415-1293 / E / 12.22.16

3.0 VENTING

WARNING

RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.

IF VENTING IS INCLUDED WITH SPACERS THE VENT SYSTEM MUST BE SUPPORTED EVERY 3FT

(0.9m) FOR BOTH VERTICAL AND HORIZONTAL RUNS. USE SUPPORTS OR EQUIVALENT

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE REQUIRED CLEARANCE FROM

COMBUSTIBLES. USE WOLF STEEL LTD. SUPPORT RING ASSEMBLY W010-0370 OR EQUIVALENT

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE MINIMUM CLEARANCE TO COMBUSTIBLES

FOR BOTH VERTICAL AND HORIZONTAL RUNS. SPACERS ARE ATTACHED TO THE INNER PIPE AT

PREDETERMINED INTERVALS TO MAINTAIN AN EVEN AIR GAP TO THE OUTER PIPE. THIS GAP IS REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED AT THE START, MIDDLE AND END OF

EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS MUST NOT BE REMOVED.

THIS APPLIANCE USES A 4” (102mm) EXHAUST / 7” (178mm) AIR INTAKE VENT PIPE SYSTEM.

Refer to the section applicable to your installation.

For safe and proper operation of the appliance follow the venting instruction exactly. Deviation from the minimum vertical vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes (5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling. The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for 400°F (204°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

NOTE: If for any reason the vent air intake system is disassembled; reinstall per the instructions provided for the initial installation.

NOTE: This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate constructions such as a chimney as part of the vent system is not permitted.

7.1F

W415-1293 / E / 12.22.16

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components

3.1 VENTING LENGTHS AND COMPONENTS

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab

venting components. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the installation procedure provided with the venting components. A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

VENT MANUFACTURER

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SuperSeal 4DNA Metal-Fab www.mtlfab.com

For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the installation procedure found on the website for your venting supplier.

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

STARTER ADAPTER PART NUMBER

SUPPLIER WEBSITE

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following termination kits: wall terminal kit GD-222, GD-222R, or 1/12 to 7/12 pitch roof terminal kit GD-110, 8/12 to 12/12 roof terminal kit GD-111, ﬂ at roof terminal kit GD-112 or periscope kit GD-201 (for wall penetration below grade). With ﬂ exible venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD-220 or the 10 foot (3.1m) vent kit GD-330.

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum. The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed and undamaged.

must not be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20 feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

8.1C

W415-1293 / E / 12.22.16

3.2 TYPICAL VENT INSTALLATION

16" (40.6CM)

MINIMUM

8" (203MM)

MINIMUM

34 5/8"

(87.9CM)

24" (61CM)

MAXIMUM

42 5/8" (108.3CM)

MINIMUM PLUS

RISE*

40 FT (12M)

MAXIMUM

3 FT (1M)

MINIMUM

34 5/8"

(87.9CM)

TOP VENT

* See "VENTING" section

W415-1293 / E / 12.22.16

16" (40.6CM)

MINIMUM

20" (50.8CM)

MAXIMUM

24 1/8" (61.3CM) MINIMUM PLUS

RISE*

40 FT (12M)

MAXIMUM

3 FT (1M)

MINIMUM

24 1/8"

(61.3CM)

* See "VENTING" section

W415-1293 / E / 12.22.16

REAR VENT

3.3 SPECIAL VENT INSTALLATIONS

30”

MINIMUM

12” MINIMUM

TOP EXIT INSTALLATION

REAR EXIT INSTALLATION

30”

MINIMUM

12” MINIMUM

MAXIMUM 10FT VENT LENGTH

6” (152.4mm) RISE MINIMUM

12” MINIMUM

3.3.1 PERISCOPE TERMINATION

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when ﬁ nal grading is completed, the bottom air slot is located a minimum 12” (30.5cm) above grade. The maximum allowable vent length is 10’ (3.1m).

30" (76.2CM)

MINIMUM

3.3.2 CORNER TERMINATION

The maximum vent length for a corner installation is 20" (50.8cm) of horizontal run, in addition to the 45° offset. Using rigid venting, zero rise is acceptable. Using ﬂexible venting, it is required to maintain a 6"(152mm) rise. See illustrations below.

6” (152.4mm) RISE MINIMUM

12" (30.5CM)

MINIMUM

TO GRADE

12" (30.5CM)

MINIMUM

TO GRADE

30" (76.2CM)

MINIMUM

34 5/8"

(87.9CM)

9.4B

20” (50.8cm)

MAXIMUM

Flex Venting Rigid Venting

W415-1293 / E / 12.22.16

3.4 MINIMUM AIR TERMINAL LOCATION CLEARANCES

COVERED BALCONY APPLICATIONS ††*

= 3 feet

MIN

(0.9m)

= 2 x

MAX

ACTUAL

MAX

INSTALLATIONS

CANADA U.S.A.

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

12” (30.5cm)

12” (30.5cm)* 12” (30.5cm) * Clearance to permanently closed windows.

18”

(45.7cm)**

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

0” (0mm)*** 0” (0mm)***

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

3’(0.9m) 3’(0.9m)****

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch or deck.

9” (229mm) Clearance to windows or doors that open.

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m) from the center line of the terminal.

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum vertical distance of 15’ (4.6m).

≤ 15 feet

(4.6m)

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

8’ (2.4m) 8’ (2.4m)

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

6’ (1.8m) 6’ (1.8m)

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Roof must be non-combustible without openings.

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening between the terminal and the open side of the structure.

NOTE: Clearances are in accordance with local installation codes and the requirements of the gas supplier.

12.1E

W415-1293 / E / 12.22.16

3.5 VENTING APPLICATION FLOW CHART

For the following symbols used in the venting calculations and examples are: > - greater than > < - less than < H H H V

Horizontal Termination

TOP EXIT

Vertical Termination

Vertical rise is equal

to or greater than

the horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

Horizontal Termination

Vertical rise is equal

to or greater than

the horizontal run

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of 24.75

feet (7.5m)

4.2 times the

vertical rise equal to

or greater than the

horizontal run

REAR EXIT

Vertical rise is less than horizontal run

Vertical rise is equal

to or greater than the horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

Vertical Termination

Vertical rise is equal

to or greater than the horizontal run

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

3 times the vertical

rise equal to or

greater than the

horizontal run

13.3A

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of 40 feet

(12m)

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m)

3.5 times the

vertical rise equal to

or greater than the

horizontal run

3.6 DEFINITIONS

- equal to or greater than

- equal to or less than

- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet

- combined horizontal vent lengths in feet

- offset factor: .03 (total degrees of offset - 90°*) in feet

- combined vertical vent lengths in feet

Horizontal run +

vertical rise to

maximum of 40 feet

(12m)

Horizontal run +

vertical rise to

maximum of 40 feet

(12m)

3 times the vertical

rise equal to or

greater than the

horizontal run

13.2A

14.1

W415-1293 / E / 12.22.16

1° 0.03 0.5 12.7 15° 0.45 6.0 152.4 30° 0.9 11.0 279.4 45° 1.35 16.0 406.4 90°* 2.7 32.0 812.8

* The ﬁ rst 90° offset has a zero value and is shown in the formula as - 90°

2.5

(0.8)5(1.5)

7.5

(2.3)

(3.1)

12.5

(3.8)15(4.6)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

17.5

(5.3)20(6.1)

39 (11.9)

REQUIRED

VERTICAL

RISE IN FEET

(METERS)VT

HORIZONTAL VENT RUN PLUS OFFSET IN

FEET (METERS) H

7.5

(2.3)

(3.1)

12.5 (3.8)15(4.6)

17.5

(5.3)20(6.1)

FEET (METERS) H

3.7 ELBOW VENT LENGTH VALUES

FEET INCHES MILLIMETERS

3.8 TOP EXIT HORIZONTAL TERMINATION

(HT) < (VT)

15.1A

Simple venting conﬁ guration (only one 90° elbow)

For vent conﬁ gurations requiring more than one 90° elbow, the following formulas apply: Formula 1: HT < V

Formula 2: HT + VT < 40 feet (12.2m)

Example: V1 = 3 FT (0.9m)

V2 = 8 FT (2.4m) VT = V1 + V2= 3 FT (0.9m ) + 8 FT (2.4m) = 11 FT (3.4m) H1 = 2.5 FT (0.8m) H2 = 2 FT (0.6m) HR = H1 + H2 = 2.5 FT (0.8m) + 2 FT (0.6m) = 4.5 FT (1.4m) HO = .03 (three 90° elbows - 90°) = .03 (270° - 90°) = 5.4 FT (1.7m) HT = HR + HO = 4.5 FT (1.4m) + 5.4 FT (1.6m) = 9.9 FT (3m) HT + VT = 9.9 FT (3m) + 11 FT (3.4m) = 20.9 FT (6.4m)

Formula 1: HT < V

9.9 FT (3m) < 11 FT (3.4m) Formula 2: HT + VT < 40 FT (12.2m)

20.9 FT (6.4m) < 40 FT (12.2m) Since both formulas are met, this vent conﬁ guration is acceptable.

W415-1293 / E / 12.22.16

RISE IN FEET

See graph to determine the required vertical

for the required horizontal run HT.

rise V

40 (12.2)

39 (11.9)

REQUIRED

30 (9.1)

VERTICAL

20 (6.1)

(METERS)VT

10 (3.1)

2.5

(0.8)5(1.5)

7.5

(2.3)

(3.1)

HORIZONTAL VENT RUN PLUS OFFSET IN

FEET (METERS) H

The shaded area within the lines represents

acceptable values for H

90°

16.1B

12.5

(3.8)15(4.6)

and V

17.5 (5.3)20(6.1)

(HT) > (VT)

Simple venting configuration

(only one 90° elbow)

See graph to determine the required vertical rise VT for the required horizontal run HT.

150 (381)

147 (373)

REQUIRED

VERTICAL

100 (254)

RISE IN INCHES

(CENTIMETERS) V

57 (145)

50 (127)

8 (20.3)

(1.5)

(0.6)

(3.1)

(4.6)

12.5 (3.8)

19.5 (5.9)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) HT

The shaded area within the lines represents acceptable values for H

For vent configurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H Formula 2: HT + V

< 4.2 V

< 24.75 feet (7.5m)

90°

Example:

= VT = 6 FT (1.8m)

= 3 FT (0.9m)

= 5 FT (1.5m)

= H

+ H

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7FT (0.8m)

= H

+ V

= 3FT (0.9m) + 5FT (1.5m) = 8FT (2.4m)

+ H

= 8FT (2.4m) + 2.7FT (0.8m) = 10.7FT (3.3m)

= 10.7FT (3.3m) + 6FT (1.8m) = 16.7FT (5.1m)

20 (6.1)

90°

and VT

Formula 1: H

4.2 VT = 4.2FT (1.3m) x 6FT (1.8m) = 25.2FT (7.7m) Formula 2: H

16.7 FT (5.1m) < 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

< 4.2 V

+ V

< 24.75 FT (7.5m)

90°

Example:

= 4 FT (1.2m)

= 1.5 FT (0.5m)

= V

+ V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= H

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

Formula 1: H

4.2 VT = 4.2 FT (1.3m) x 5.5 FT (1.7m) = 23.1 FT (7m)

= 4 FT (1.2m) + 1.5 FT (0.5m) = 5.5 FT (1.7m)

+ H2 + H

+ H

= 13.6 FT (4.2m) + 5.5 FT (1.7m) = 19.1 FT (5.8m)

+ H4 = 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

= 5.5 FT (1.7m) + 8.1 FT (2.5m) = 13.6 FT (4.2m)

< 4.2 V

13.6 FT (4.2m) < 23.1 FT (7m) Formula 2: HT + V

19.1 FT (5.8m) < 24.75 FT (7.5m)

< 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

90°

16.16

90°

W415-1293 / E / 12.22.16

(HT) < (VT)

3.9 REAR EXIT HORIZONTAL TERMINATION

Simple venting configuration

(only two 90° elbows)

See graph to determine the required vertical rise V

horizontal run H

40 (12.2)

38.3 (11.7)

REQUIRED

30 (9.1)

VERTICAL

RISE IN

20 (6.1)

FEET

(METERS) V

1.6 (0.5)

10 (3.1)

2.5

(0.8)5 (1.5)

1.6

(0.5)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

The shaded area within the lines represents acceptable values for H

and HT

For vent configurations requiring more than two 90° elbows, the following formulas apply:

Formula 1: H Formula 2: HT + V

Example:

= 9 FT (2.7m)

= 6 FT (1.8m)

= V

= 3 FT (0.9m)

= 2 FT (0.6m)

= 1.5 FT (0.5m)

= H

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

Formula 1: H

14.6 FT (4.5m) < 15 FT (4.6m) Formula 2: HT + V

29.6 FT (9m) < 40 FT (12.2m)

< V

< 40 feet (12.2m)

+ V

= 9FT (2.7m) + 6FT (1.8m) = 15FT (4.6m)

+ H2 + H

+ H

= 14.6FT (4.5m) + 15FT (4.6m) = 29.6 FT (9m)

= 3FT (0.9m) + 2FT (0.6m) + 1.5FT (0.5m) = 6.5FT (2m)

= 6.5FT (2m) + 8.1FT (2.5m) = 14.6FT (4.5m)

< V

< 40 FT (12.2m)

Since both formulas are met, this vent configuration is acceptable.

7.5

(2.3)

for the required

12.5 (3.8)

17.5 (5.3)

(6.1)

(4.6)

(3.1)

90°

W415-1293 / E / 12.22.16

16.3A

Simple venting configuration

(HT) > (VT)

(HT) < (VT)

See graph to determine the required vertical rise VT for the required horizontal run HT.

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

39 (11.9)

GD36

REQUIRED

VERTICAL

RISE IN FEET

(METERS)V

(only two 90° elbows)

See graph to determine the required vertical rise V

150(3810)

147 (3733.8

required horizontal run H

for the

REQUIRED

VERTICAL RISE IN

100 (2540)

INCHES

(MILLIMETERS)V

(1676.4)

50 (1270)

(304.8)

8 (203)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

The shaded area within the lines represents acceptable

For vent configurations requiring more than two 90° elbows, the following formulas apply:

Formula 1: H Formula 2: HT + V

< 3.5V

< 24.75 feet (7.5m)

Example:

= 4 FT (1.2m)

= 1.5 FT (0.5m)

= V

+ V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= H1+ H2+H3+H4= 2FT(0.6m) + 1FT(0.3m) + 1FT(0.3m) + 1.5FT(0.5m) = 5.5 FT(1.7m)

= .03 (four 90° elbows + one 45° elbow - 90°)

= .03 (90 + 90 + 90 + 90 + 45 - 90) = 9.45 FT (2.9m)

= H

+ V

Formula 1: H

3.5VT = 3.5FT (1.1m) x 5.5FT (1.7m) = 19.25FT (5.9m)

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

+ H

= 5.5FT (1.7m) + 9.45FT (2.9m) = 14.95FT (4.6m)

= 14.95FT (4.6m) + 5.5FT (1.7m) = 20.45FT (6.2m)

< 3.5V

14.95 FT (4.6m) < 19.25 FT (5.9m)

Formula 2: HT + V

20.45 FT (6.2m) < 24.75 FT (7.5m)

< 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

2.5

(0.8)5 (1.5)

(0.3)

values for H

(1.1)

3.5

(1.1)

7.5

12.5

17.5

12.5

7.5

(2.3)

(3.1)

(2.3)

3.5

and HT

(3.8)

(4.6)

17.5

(5.3)

19.25

(5.9)

(6.1)

90°

16.3_2B

W415-1293 / E / 12.22.16

for the

(HT) < (VT)

3.10 TOP AND REAR EXIT VERTICAL TERMINATION

Simple venting configurations.

See graph to determine the required vertical rise V

required horizontal run HT.

40 (12.2)

30 (9.1)

REQUIRED

VERTICAL RISE

IN FEET

(METERS)V

20 (6.1)

10 (3.1)

3 (0.9)

(1.5)

(3.1)

(4.6)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET

(METERS) H

The shaded area within the lines represents acceptable

values for H

and HT

For vent configurations requiring one or more 90° elbows (top exit) or one or more 90° elbows (rear exit), the following formulas apply:

Formula 1: H Formula 2: HT + V

< V

< 40 feet (12.2m)

(6.1)

Example:

= 5 FT (1.5m)

= 6 FT (1.8m)

= 10 FT (3.1m)

= V

+ V2 + V

= 8 FT (2.4m)

= 2.5 FT (0.8m)

= H1+ H2 = 8FT (2.4m) + 2.5FT (0.8m) = 10.5FT (3.2m)

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ H

+ V

= 18.6FT (5.7m) + 21FT (6.4m) = 39.6FT (12.1m)

Formula 1: H

18.6 FT (5.7m) < 21 FT (6.4m) Formula 2: HT + V

39.6FT (12.1m) < 40 FT (12.2m)

= 5FT (1.5m) + 6FT (1.8m) + 10FT (3.1m) = 21 FT (6.4m)

= 10.5FT (3.2m) + 8.1FT (2.5m) = 18.6FT (5.7m)

< 3.5V

< 40 FT (12.2m)

Since both formulas are met, this vent configuration is acceptable.

18.2A

W415-1293 / E / 12.22.16

Example:

Simple venting configurations.

See graph to determine the required vertical rise V

for the

required horizontal run H

REQUIRED

VERTICAL

RISE IN

FEET

(METERS)V

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS)H

The shaded area within the lines represents acceptable

values for H

and HT

(1.5)

(3.1)

(4.6)

(6.1)

10 (3.1)

20 (6.1)

3 (0.9)

(7.6)

(9.1)

19 (5.8)

90°

(HT) > (VT)

18.2_2B

For vent configurations requiring more than two 90° elbows (top exit) or one 90° elbow (rear exit), the following formulas apply:

Formula 1: H

< 3 V

Formula 2: HT + V

< 40 feet (12.2m)

Example: V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= V

+ V2 + V3 = 2FT (0.6m) + 1FT (0.3m) + 1.5FT (0.5m) = 4.5 FT (1.4m)

= 6 FT (1.8m)

= 2 FT (0.6m)

= H

+ H

= 6FT (1.8m) + 2FT (0.6m) = 8 FT (2.4m)

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ H

= 8FT (2.4m) + 8.1FT (2.5m) = 16.1FT (4.9m)

+ V

= 16.1FT (4.9m) + 4.5FT (1.4m) = 20.6FT (6.3m)

Formula 1: H

< 3.5 V

3.5 V

= 3FT (0.9m) x 4.5FT (1.4m) = 13.5 FT (4.1m)

16.1FT (4.9m) < 13.5 FT (4.1m) Since this formula is not met, this vent configuration is unacceptable.

Formula 2: HT + V

< 40 FT (12.2m)

16.1FT (4.9m) < 13.5 (4.1m)

Since only formula 2 is met, this vent configuration is unacceptable and a new fireplace location or vent configuration will need to be established to satisfy both formulas.

= 1.5 FT (0.5m)

= 5 FT (1.5m)

= V

V H H H H H = .03 (360° + 45° - 90°) = 6.75 FT (2.1m) H H

+ V2 = 1.5FT (0.5m)+ 5FT (1.5m) = 6.5 FT (2m)

= 1 FT (0.3m)

= 10.75 FT (3.3m)

= H

+ H2 + H3 = 1FT (0.3m) + 1FT (0.3m) + 10.75FT (3.3m) = 12.75FT (3.9m)

= .03 (four 90° elbows + one 45° elbow - 90°)

= H

+ H

+ V

= 12.75FT (3.9m) + 6.75FT (2.1m) = 19.5 FT (5.9m)

= 19.5FT (5.9m) + 6.5FT (2m) = 26 FT (7.9m)

Formula 1:

< 3 V

3 V

19.5FT (5.9m) = 19.5FT (5.9m) Formula 2:

HT + V 26 FT (7.9m) < 40 FT (12.2m)

Since both formulas are met, this vent conﬁguration is acceptable.

= 3FT (0.9m) x 6.5FT (2m) = 19.5FT (5.9m)

< 40 FT (12.2m)

90°

45°

90°

18.2_3A

W415-1293 / E / 12.22.16

90°

WARNING

FAILURE TO CREATE A SEAL TO THE FIREBOX WITH THE EXHAUST COLLAR ASSEMBLY WILL CAUSE

DEFLECTOR

3.11 REAR EXIT

THE APPLIANCE TO FUNCTION IMPROPERLY AND CAN CAUSE INJURY OR PROPERTY DAMAGE.

Fig. 1

A. Remove the safety screen and glass front, refer to "

SAFETY SCREEN / DOOR REMOVAL AND INSTALLATION" section.

B. Remove the contents from the ﬁrebox and set aside, you

will need the exhaust ﬂue collar from the top of the log carton.

C. To ease assembly, remove the four hex head screws

securing the deﬂector from inside the top front of the ﬁrebox, refer to Figure 1.

D. Place the gasket (provided) over the 4" (102mm) ﬂue collar assembly and

bend along perforation.

E. From inside the ﬁrebox, insert the 4" (102mm) ﬂue collar through the back

of the ﬁrebox. Install the rear exit shield onto the 4" (102mm) ﬂue collar, see "REAR EXIT SHIELD" section for installation instructions.

F. Secure the ﬂue collar assembly, gasket and rear exit shield using the four

hex head 3/8" thread cutting screws, refer to Figure 2. NOTE: Do not

overtighten. The gasket needs only to be snug against the ﬁrebox.

G. Reattach the deﬂector using the four screws and install the log set, glass

door and safety screen.

Fig. 2

3.12 REAR EXIT SHIELD (FOR REAR VENT ONLY)

A. Remove the safety barrier assembly and door from the appliance, refer to the “SAFETY SCREEN & DOOR REMOVAL / INSTALLATION” section of the manual for detailed instructions.

B. Loosen the two screws, that secure the exhaust plate, and slide the bafﬂe in place by sliding its slotted openings behind the screwheads, tighten the two previously loosened screws. Refer to the illustration below.

C. Reinstall the door and safety barrier assembly on the appliance, refer to the “SAFETY SCREEN & DOOR REMOVAL / INSTALLATION” section of the manual for detailed instructions.

NOTE: THIS SHIELD IS USED TO BLOCK THE VIEW THROUGH THE VENTING TO THE OUTDOORS.

W415-1293 / E / 12.22.16

3.13 TOP EXIT

INTAKE COLLAR

ASSEMBLY

GASKET

OUTER COVER

WARNING

DEFLECTOR

FAILURE TO INSTALL THE COVER PLATE AND GASKET WILL CAUSE THE APPLIANCE TO

FUNCTION IMPROPERLY AND CAN CAUSE INJURY OR PROPERTY DAMAGE.

NOTE: This appliance has been factory shipped as a rear vent.

A. Remove the safety screen and glass front, refer to " SAFETY SCREEN / DOOR REMOVAL AND

INSTALLATION" section.

B. Remove the contents from the ﬁrebox and set aside,

you will need the exhaust collar from the top of the log carton.

C. To ease assembly, remove the four hex head screws

securing the deﬂector from inside the top front of the ﬁrebox.

D. Remove the single screw from the outer cover on the

back of the appliance.

E. Remove the four screws on the 7" (178mm) intake

collar assembly; set the intake collar and gasket aside. Careful not to damage gasket.

F. Remove the single screw from the outer cover with

knockout intact, on the top of the appliance and set aside.

G. Remove the inner cover plate and gasket by removing

the four screws. Reinstall the inner cover plate and gasket onto the back of the appliance.

H. Take the outer cover (with knockout intact) and secure

onto the back of the appliance.

I. Remove and discard the 1 1/2" thick batt of insulation

from the top opening.

J. Place the 7" (178mm) intake collar

and gasket onto the top of the appliance and secure with the four screws.

K. Reinstall the outer cover (without

knock out) over the 7" (178mm) exhaust collar assembly and secure.

L. From inside the ﬁrebox, install the 4"

(102mm) exhaust collar up through the top of the ﬁrebox and secure with the the four hex head 3/8" thread cutting screws. NOTE: Do

not overtighten. The gasket needs only to be snug against the ﬁrebox.

M. Reattach the top deﬂector, log set, glass

door and safety screen.

OUTER

COVER

(with knockout)

GASKET

INTAKE COLLAR

ASSEMBLY

OUTER COVER

INNER COVERPLATE

EXHAUST FLUE COLLAR

GASKET

W415-1293 / E / 12.22.16

WARNING

IF USING PIPE CLAMPS TO CONNECT VENT COMPONENTS, A MINIMUM OF 3 SCREWS MUST ALSO

4.0 INSTALLATION

ENSURE TO UNPACK ALL LOOSE MATERIALS FROM INSIDE THE FIREBOX PRIOR TO HOOKING UP

THE GAS AND ELECTRICAL SUPPLY.

IF YOUR APPLIANCE IS SUPPLIED WITH A REMOTE, ENSURE THE REMOTE RECEIVER IS IN THE

“OFF” POSITION PRIOR TO HOOKING UP THE GAS AND ELECTRICAL SUPPLY TO THE APPLIANCE.

FOR SAFE AND PROPER OPERATION OF THE APPLIANCE, FOLLOW THE VENTING INSTRUCTIONS

EXACTLY.

ALL EXHAUST AND INTAKE VENT PIPE JOINTS MUST BE SEALED USING RED RTV HIGH TEMP

SILICONE SEALANT (W573-0002) (NOT SUPPLIED) OR BLACK HIGH TEMP MILL PAC (W573-0007)

(NOT SUPPLIED) WITH THE EXCEPTION OF THE APPLIANCE EXHAUST FLUE COLLAR WHICH MUST

BE SEALED USING MILL PAC.

BE USED TO ENSURE THE CONNECTION CANNOT SLIP OFF.

DO NOT CLAMP THE FLEXIBLE VENT PIPE.

RISK OF FIRE, EXPLOSION OR ASPHYXIATION. IMPROPER SUPPORT OF THE ENTIRE VENTING

SYSTEM MAY ALLOW VENT TO SAG AND SEPARATE. USE VENT RUN SUPPORTS AND CONNECT

VENT SECTIONS PER INSTALLATION INSTRUCTIONS.

RISK OF FIRE, DO NOT ALLOW LOOSE MATERIALS OR INSULATION TO TOUCH THE VENT PIPE.

REMOVE INSULATION TO ALLOW FOR THE INSTALLATION OF THE ATTIC SHIELD AND TO

MAINTAIN CLEARANCES TO COMBUSTIBLES.

68.2D

4.1 WALL AND CEILING PROTECTION

DO NOT FILL THE SPACE BETWEEN THE VENT PIPE AND ENCLOSURE WITH ANY TYPE OF

MATERIAL. DO NOT PACK INSULATION OR COMBUSTIBLES BETWEEN CEILING FIRESTOPS.

ALWAYS MAINTAIN SPECIFIED CLEARANCES AROUND VENTING AND FIRESTOP SYSTEMS.

INSTALL WALL SHIELDS AND FIRESTOPS AS SPECIFIED. FAILURE TO KEEP INSULATION OR

OTHER MATERIALS AWAY FROM VENT PIPE MAY CAUSE FIRE.

For clearances to combustible materials from the vent pipe, see “FRAMING” section.

70.1

W415-1293 / E / 12.22.16

CAULKING

VENT

PIPE

COLLAR

4.1.2 HORIZONTAL INSTALLATION

20.7D

WARNING

THE FIRESTOP ASSEMBLY MUST BE INSTALLED WITH THE VENT SHIELD TO THE TOP.

TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE

RETURN FLANGE OF THE MOUNTING PLATE.

This application occurs when venting through an exterior wall. Having determined the correct height for the air terminal location, cut and frame a hole in the exterior wall as illustrated to accommodate the ﬁ restop assembly. Dry ﬁ t the ﬁ restop assembly before proceeding to ensure the brackets on the rear surface ﬁ t to the inside surface of the horizontal framing.

The vent shield must be installed to the full depth of the combustible wall. The length of the vent shield may be cut shorter for combustible walls that are less than 8 1/2" (216mm) thick.

reduced side clearances or move the shield for reduced top clearances.

A. Apply a bead of caulking (not supplied) around the corner edge of the inside surface of the ﬁ restop assembly, ﬁ t the ﬁ restop assembly to the hole and secure using the 4 screws (supplied in your manual baggie).

NOTE : Do not ﬁ ll the air space

between the ﬁ restop spacer and the exterior wall with any type of insulating material (i.e., spray foam).

B. Once the vent pipe is installed in its ﬁ nal position, apply red ﬁ restop.

NOTE: Bend the tabs for

RTV silicone sealant (W573-0002) (not supplied) between the pipe and the

CAULKING

FIRESTOP

SPACER

CAULKING

VENT

SHIELD

DETERMINE THE CORRECT HEIGHT

FINISHING MATERIAL

4.1.1 VERTICAL INSTALLATION

This application occurs when venting through a roof. Installation kits for various roof pitches are available from your authorized dealer / distributor. See accessories to order speciﬁ c kits required.

A. Determine the air terminal location, cut and frame a square opening as

illustrated in the ceiling and the roof to provide the minimum 1" (25mm) clearance between the vent pipe and any combustible material. Try to center the vent pipe location midway between two joists to prevent having to cut them. Use a plumb bob to line up the center of the openings. A vent pipe shield will prevent any materials such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe. Nail headers between the joist for extra support.

B. Apply a bead of caulking (not supplied) to the framework or to the

Wolf Steel vent pipe shield plate or equivalent (in the case of a ﬁ nished ceiling), and secure over the opening in the ceiling. A ﬁ restop must be placed on the bottom of each framed opening in a roof or ceiling that the venting system passes through. Apply a bead of caulking all around and place a ﬁ restop spacer over the vent shield to restrict cold air from being drawn into the room or around the ﬁ replace. Ensure that both spacer and shield maintain the required clearance to combustibles. Once the vent pipe is installed in its ﬁ nal position, apply Mill Pac sealant (W573-0007) (not supplied) or red RTV silicone (W573-0002) (not supplied) between the pipe and the ﬁ restop assembly.

C. In the attic, slide the vent pipe collar down to cover up the open end of the shield and

tighten. This will prevent any materials, such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

FIRESTOP

UNDERSIDE OF

JOIST

VENT PIPE

SHIELD

VENT

PIPE

SHIELD

21.1B

W415-1293 / E / 12.22.16

temperature sealant W573-0007 Mill Pac (not supplied). However, the high

SPACERS ARE ATTACHED TO THE INNER FLEX PIPE AT PREDETERMINED INTERVALS TO MAINTAIN AN EVEN

WARNING

A. Stretch the inner ﬂ ex pipe to the required length taking into

The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the depth of its return ﬂ ange.

#8 X 1/2” SELF DRILLING

HI-TEMP

SEALANT

4.2 USING FLEXIBLE VENT COMPONENTS

DO NOT ALLOW THE INNER FLEX PIPE TO BUNCH UP ON HORIZONTAL OR VERTICAL RUNS AND ELBOWS.

KEEP IT PULLED TIGHT.

AIR GAP TO THE OUTER FLEX PIPE. THIS GAP IS REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED

AT THE START, MIDDLE AND END OF EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS

MUST NOT BE REMOVED.

For safe and proper operation of the appliance, follow the venting instructions exactly. All inner ﬂ ex pipe and outer ﬂ ex pipe joints may be sealed using high

ELBOW

SPACERS

temperature red RTV silicone W573-0002 (not supplied) or the high

temperature sealant W573-0007 Mill Pac (not supplied) must be used on the joint connecting the inner ﬂ ex pipe and the exhaust ﬂ ue collar.

Use only approved ﬂ exible vent pipe kits marked:

“Wolf Steel Approved Venting” as identiﬁ ed by the stamp only on the outer ﬂ ex pipe.

22.1A

4.2.1 HORIZONTAL AIR TERMINAL INSTALLATION

account the additional length needed for the ﬁ nished wall surface. Apply a heavy bead of the Mill Pac sealant (W573-0007) (not supplied) to the inner sleeve of the air terminal. Slip the vent pipe a minimum of 2” (50.8mm) over the inner sleeve of the air terminal and secure with a minimum of 3 #8 screws.

Using the outer ﬂ ex pipe, slide over the outer

combustion air sleeve of the air terminal and secure with a minimum of 3 #8 screws. Seal using red RTV silicone (W573-0002) (not supplied).

Insert the vent pipes through the ﬁ restop maintaining the

required clearance to combustibles. Holding the air terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing with caulking (not supplied).

If more vent pipe needs to be used to reach the ﬁ replace,

couple them together as illustrated. The vent system must be supported approximately every 3 feet (0.9m) for both vertical and horizontal runs. Use noncombustible strapping to maintain the minimum clearance to combustibles.

#10x2"

SCREWS

HI-TEMP

SEALANT

OUTER

FLEX PIPE

CAULKING

INNER FLEX

PIPE

2" (50.8mm) OVERLAP

HIGH TEMPERATURE

INNER FLEX PIPE

OUTER FLEX PIPE

SEALANT

SCREWS

INNER COUPLER

OUTER COUPLER

OUTER

FLEX PIPE

W415-1293 / E / 12.22.16

23.1C

4.2.2 VERTICAL AIR TERMINAL INSTALLATION

WARNING

MAINTAIN A MINIMUM 2” (51mm) SPACE BETWEEN THE AIR INLET BASE AND THE STORM COLLAR.

Fasten the roof support to the roof using the screws provided. The

roof support is optional. In this case the venting is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the optional roof support.

Stretch the inner ﬂ ex pipe to the required length. Slip the

inner ﬂ ex pipe a minimum of 2” (51mm) over the inner pipe of the air terminal connector and secure with a minimum of

3 #8 screws. Seal using a heavy bead of Mill Pac sealant (W573-0007) (not supplied).

Repeat using the outer ﬂ ex pipe, using a heavy bead

of red RTV silicone (W573-0002) (not supplied) and a minimum of 3 #8 screws.

Thread the air terminal connector / vent pipe assembly down through

the roof. The air terminal must be positioned vertically and plumb. Attach the air terminal connector to the roof support, ensuring that the top of the air terminal is 16” (40.6cm) above the highest point that it penetrates the roof.

Remove nails from the shingles, above and to the sides of the air

terminal connector. Place the ﬂ ashing over the air terminal connector leaving a min. 3/4” (19mm) of the air terminal connector showing above the top of the ﬂ ashing. Slide the ﬂ ashing underneath the sides and upper edge of the shingles. Ensure that the air terminal connector is properly centered within the ﬂ ashing, giving a 3/4” (19mm) margin all around. Fasten to the roof. Do not nail through the lower portion of the ﬂ ashing. Make weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the ﬂ ashing with rooﬁ ng material.

Aligning the seams of the terminal and air terminal connector,

place the terminal over the air terminal connector making sure the vent pipe goes into the hole in the terminal. Secure with the three screws provided.

Apply a heavy bead of weatherproof caulking 2” (51mm)

above the ﬂ ashing. Install the storm collar around the air terminal and slide down to the caulking. Tighten to ensure that a weather-tight seal between the air terminal and the collar is achieved.

If more vent pipe needs to be used to reach the appliance see

“HORIZONTAL AIR TERMINAL INSTALLATION” section.

ROOF SUPPORT

AIR

TERMINAL

CONNECTOR

2” (51mm)

INNER PIPE

MILL PAC

SEALANT

(W572-0007)

INNER FLEX PIPE

OUTER FLEX PIPE

AIR INLET BASE

CAULKING

STORM COLLAR

WEATHER SEALANT

FLASHING

24.1C

W415-1293 / E / 12.22.16

The vent system must be supported approximately every 3 feet (0.9m) for both vertical and horizontal runs. Use Wolf Steel Ltd. support ring assembly or equivalent noncombustible strapping to maintain the minimum clearance to combustibles for both vertical and horizontal runs.

All inner exhaust and outer intake vent pipe joints may be sealed using either red high temperature silicone sealant (W573-0002) (not supplied) or black high temperature sealant W573-0007 Mill Pac (not supplied) with the exception of the appliance exhaust ﬂ ue collar which must be sealed using Mill Pac.

The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the depth of the return ﬂ ange.

WARNING

A. Install the inner exhaust ﬂ ue collar to the appliance. Secure

4.2.3 APPLIANCE VENT CONNECTION

with a minimum of 3 #8 screws. Seal the joint and screw holes using Mill Pac sealant (W573-0007) (not supplied).

Install the outer ﬂ ex pipe to the appliance. Attach and seal the joints using a red RTV silicone and a minimum of 3 #8 screws.

4.3 USING RIGID VENT COMPONENTS

4.3.1 HORIZONTAL AIR TERMINAL INSTALLATION

RISK OF FIRE, DO NOT ALLOW LOOSE MATERIALS OR INSULATION TO TOUCH THE VENT PIPE.

REMOVE INSULATION TO ALLOW FOR THE INSTALLATION OF THE ATTIC SHIELD AND TO

MAINTAIN CLEARANCES TO COMBUSTIBLES.

Move the appliance into position. Measure the

vent length required between terminal and appliance taking into account the additional length needed for the ﬁ nished wall surface and any 1¼” (31.8mm) overlaps between venting components.

Apply high temperature sealant W573-0007 Mill Pac

(not supplied) to the outer edge of the inner exhaust ﬂ ue collar of the appliance. Attach the ﬁ rst inner rigid pipe component and secure using a minimum of 3 self tapping screws. Repeat using the outer rigid pipe.

Insert the vent pipes through the ﬁ restop maintaining the required clearance to combustibles. Holding

the air terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing with caulking (not supplied).

#8 X 1/2”

SELF

DRILLING

SCREWS

28.1D

25.1A

2” (50.8mm) OVERLAP

HIGH TEMP SEALANT

#10x2"

SCREWS

CAULKING

OUTER RIGID PIPE

1" (25.4mm)

OVERLAP

HI-TEMP INNER RIGID PIPE

#8x1/2"

SELF DRILLING

SCREWS

SEALANT

W415-1293 / E / 12.22.16

26.1A

4.3.2 VERTICAL AIR TERMINAL INSTALLATION

A. Move the appliance into position. B.

Install the storm collar around the air terminal and slide down to the caulking. Tighten to ensure that a

CAULKING

FIRESTOP

UNDERSIDE OF

JOIST

VENT

PIPE

COLLAR

VENT

PIPE

SHIELD

Fasten the roof support to the roof using the screws provided. The

roof support is optional. In this case the venting is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the optional roof support.

Apply high temperature sealant (not supplied) to the outer edge of

the inner sleeve of the air terminal. Slip the inner coupler a minimum of 2" (51mm)over the sleeve and secure using a minimum of 3 screws.

Apply high temperature sealant (not supplied) to the outer edge of

the of the outside sleeve of the air terminal connector. Slip the outer coupler over the sleeve and secure as before. Trim the outer coupler even with the inner coupler end.

Thread the air terminal connector / vent pipe assembly down

through the roof support and attach, ensuring that a minimum 16" (40.6cm) of air terminal connector will penetrate the roof when fastened. If the attic space is tight, we recommend threading the Wolf

Run a bead of red RTV silicone (not supplied) around the outside of the inner exhaust ﬂ ue collar

Steel vent pipe collar or equivalent loosely onto the air terminal connector / vent pipe assembly as it is passed through the attic. The air terminal connector must be located vertically and plumb.

Remove nails from the shingles, above and to the sides of the air terminal

connector. Place the ﬂ ashing over the air terminal connector and slide it underneath the sides and upper edge of the shingles. Ensure that the air terminal connector is properly centered within the ﬂ ashing, giving a 3/4" (19mm) margin all around. Fasten to the roof. Do NOT nail through the lower portion of the ﬂ ashing. Make weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the ﬂ ashing with rooﬁ ng material.

Apply a heavy bead of waterproof caulking 2" (51mm) above the ﬂ ashing.

weather-tight seal between the air terminal connector and the collar is achieved.

Continue adding rigid venting sections, sealing and securing as above. Attach the inner collapsed

telescopic sleeve to the last section of rigid piping. Secure with screws and seal. Repeat using the outer telescopic sleeve.

on the appliance. Pull the telescopic sleeve a minimum of 2" (51mm) onto the collar. Secure with a mnimum of 3 screws. Repeat with the outer telescopic sleeve.

In the attic, slide the vent pipe collar down to cover up the open end of the shield and tighten. This

will prevent any materials, such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

AIR

TERMINAL

CONNECTOR

INNER RIGID

27.2A

INNER PIPE

HIGH TEMPERATURE SEALANT

PIPE

OUTER

RIGID PIPE

W415-1293 / E / 12.22.16

WARNING

3. LEAST RESTRICTION

4.3.3 RESTRICTING VERTICAL VENTS

TURN OFF GAS AND ELECTRICAL SUPPLY BEFORE SERVICING THE APPLIANCE.

APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE IS COOL.

FOR SAFE AND PROPER OPERATION OF THE APPLIANCE, FOLLOW THE VENTING INSTRUCTION EXACTLY

TO AVOID DANGER OF SUFFOCATION KEEP THE PACKAGING BAG AWAY FROM BABIES AND CHILDREN.

DO NOT USE IN CRIBS, BED, CARRIAGES OR PLAY PENS. THIS BAG IS NOT A TOY. KNOT BEFORE

Vertical installations may display a very active ﬂame. If this appearance is not desirable, the exhaust outlet may be restricted with a Wolf Steel approved restrictor kit. This kit is not recommended for short vertical vent runs.

Depending on the model and/or year of your appliance, mounting holes may not exist. A. If mounting holes exist, remove the screws from the ﬁrebox top, align the restrictor plate as illustrated

and secure. B. If mounting holes do not exist, align the restrictor plate as illustrated and secure using the two

#8x1/2 hex head sheet metal screws supplied.

C. Ensure the plate will pivot at the slot up into the exhaust outlet. D. Depending on the amount of restriction desired, the restrictor plate can be left ﬂat for most restriction

or bent up for varying degrees of restriction.

THROWING AWAY.

MOUNTING SCREWS

RESTRICTOR

EXHAUST COLLAR

#8 x ½ HEX HEAD

SHEET METAL

SCREW

TOP VIEW

FIREBOX TOP

RESTRICTOR

FIREBOX TOP

1. MOST RESTRICTION

2. MODERATE RESTRICTION

W415-1293 / E / 12.22.16

+ 102 hidden pages