Napoleon B30NTRE1 Installation Manual

NATURAL GAS MODELS:

B30NTR-1 / B30NTRE-1

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

ENGLISH

PROPANE GAS MODELS:

SAFETY INFORMATION

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

B30PTR-1 / B30PTRE-1

FRENCH

PG. 69

INSTALLATION AND

ADD MANUAL TITLE

OPERATION MANUAL

Product Name / Code

(MUST use title from Price Book)

SAFETY BARRIER

ADD PRODUCT IMAGE

Ascent™ 30

ADD ____ ILLUSTRATED

- Installation and service must be

performed by a qualiﬁ ed installer, service agency, or the supplier.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleonﬁ replaces.com • hearth@napoleonproducts.com

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

CSA /

INTERTEK

LOGO

FOR INDOOR USE ONLY

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

$10.00

W415-1768 / B / 08.10.18

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

WARNING

safety information

• This appliance is hot when operated and can cause severe burns if contacted.

• Any changes or alterations to this appliance or its controls can be dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure to operate appliance according to operating instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed

when lighting the pilot for the ﬁ rst time and when the gas supply has run out.

• Risk of ﬁ re or asphyxiation, do not operate

appliance with ﬁ xed glass removed and never obstruct the front opening of the appliance.

• Do not connect 110 volts to the control valve,

with the exception of models; GSST8 and GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing

and operating the appliance.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from

furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior

to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it

serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame patterns.

W415-1768 / B / 08.10.18

before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame

patterns.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

WARNING

WARNING:

Electric

This product can expose you to chemicals including lead and lead compounds,

Gas, Wood

which are known to the State of California to cause cancer, and chemicals including BBP and DEHP, which are known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

AVERTISSEMENT:

Ce produit peut vous exposer à des substances chimiques incluant le

plomb et les composés de plomb qui, selon l’État de Californie, causeraient le cancer, et des substances chimiques incluant le BBP et DEHP qui, selon d’État de Californie, causeraient des malformations congénitales ou autres dangers pour la reproduction. Pour de plus amples renseignements, visitez le www.P65Warnings.ca.gov.

ADVERTENICA:

Este producto puede exponerlo a productos químicos, entre ellos, plomo y compuestos con plomo, que el Estado de California reconoce como causantes de cáncer, y productos químicos, entre ellos, bencilbutilftalato (BBP, por sus siglas en inglés) y di(2-etilhex- il) ftalato (DEHP, por sus siglas en inglés), que el Estado de California reconoce como caus- antes de malformaciones congénitas u otros daños para la reproducción. Para obtener más información, visite www.P65Warnings.ca.gov.

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these openings can also cause the surrounding combustible materials to overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the

ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide (not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V. or other electronic components.

• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. It is imperative that control

• For outdoor products only: this appliance must not be installed indoors or within any structure that

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace

compartments, burners and circulating air passageways of the appliance be kept clean.

prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

only with a fast acting thermocouple supplied by Wolf Steel Ltd.

WARNING:

which are known to the State of California to cause cancer, and chemicals including carbon monoxide, which are known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Add California Prop 65 warning

This product can expose you to chemicals including lead and lead compounds,

safety information

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

W415-1768 / B / 08.10.18

table of contents

1.0 general information 5

1.1 rates and efﬁciencies 5

1.2 rating plate information 7

1.3 dimensions 8

2.0 venting requirements 9

2.1 typical vent installation 10

2.2 special vent installations 12

2.2.1 periscope termination 12

2.2.2 corner termination 12

2.3 minimum air terminal location

clearances 13

2.4 venting application ﬂow chart 14

2.5 deﬁnitions 14

2.6 elbow vent length values 15

2.7 top exit horizontal termination 15

2.8 rear exit horizontal termination 17

2.9 top and rear exit vertical termination 19

2.10 rear exit 21

2.11 rear exit shield (for rear vent only) 21

2.12 top exit 22

3.0 rough framing 23

3.1 minimum framing dimensions 24

3.2 minimum enclosure clearances 25

4.0 venting installation 30

4.1 horizontal installation 31

4.2 vertical installation 31

4.3 using either ﬂexible or rigid vent

components 32

4.3.1 horizontal air terminal installation 32

4.3.2 vertical air terminal installation 33

4.3.3 appliance vent connection 33

4.3.4 horizontal air terminal installation 34

4.3.5 vertical air terminal installation 35

4.4 vertical through existing chimney 36

4.4.1 restricting vertical vents 37

5.0 electrical information 38

5.1 battery back-up installation 39

5.2 optional wall switch 40

6.0 gas installation 40

7.0 operation (electronic) 41

8.0 operation (millivolt) 42

9.1 minimum framing dimensions 43

9.0 finish framing 43

10.0 finishing 44

10.1 safety barrier / door removal and

installation 44

10.2 front hood installation 45

10.3 non-combustible facing material 46

10.4 alcove clearances 47

10.5 minimum mantel clearances 47

10.6 recessed installation 48

10.7 log placement 49

10.8 charcoal embers 50

10.9 logo placement 50

11.0 adjustments 51

11.1 pilot burner adjustment 51

11.2 venturi adjustment 51

11.3 ﬂame characteristics 52

11.4 optional anti condensation switch (models B30NTRE-1 and B30PTRE-1 only) 52

12.0 maintenance 53

12.1 annual maintenance 54

12.2 door glass replacement 55

12.3 care of glass 55

13.0 replacement parts 56

13.1 overview 57

13.2 electronic valve train assembly 58

13.3 millivolt valve train assembly 59

14.0 accessories 60

15.0 troubleshooting (electronic) 61

16.0 troubleshooting (millivolt) 64

17.0 warranty 66

note:

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves the right to change or modify any information within this manual at any time without notice. Changes, other than editorial, are denoted by a vertical line in the margin.

W415-1768 / B / 08.10.18

Installer: please ﬁll out the following information

Customer: Address: Date of Installation: Location of the appliance Installer: Dealer/Distributor contact number: Serial #:

Model:

standard checklist

Natural Gas: B30NTR-1 B30NTRE-1

Propane: B30PTR-1 B30PTRE-1

1.0 general information

When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speciﬁc recommendations from the local authority having jurisdiction, the certiﬁed high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft (305m). Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected. Change in ﬂame appearance from “HI” to “LO” is more evident in natural gas than in propane.

This appliance is approved for bathroom, bedroom and bed-sitting room installations and is certiﬁed for mobile home installation.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

note:

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance and must be installed.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat source.

This appliance is a decorative product. It is not a source of heat and not intended to burn solid fuel.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be recycled, and may be accepted for disposal at your local recycling center. Check with your municipality for recycling instructions.

1.1 rates and efﬁciencies

Altitude (FT) 0-4,500 0-4,500 Max. Input (BTU/HR) 15,000 15,000 Min. Inlet Gas Supply Pressure 4.5" (11mb) w.c. 11" (27mb) w.c. Max. Inlet Gas Supply Pressure 13" (32mb) w.c. 13" (32mb) w.c.

Manifold Pressure (Under Flow Conditions)

Natural Gas Propane

3.5" (9mb) w.c. 10" (25mb) w.c.

W415-1768 / B / 08.10.18

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

general information

WARNING

• Always light the pilot whether for the ﬁrst time or if the gas supply has run out, with the glass door opened or removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of the appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when appliance is operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test pressures above 1/2 PISG (35mb). Close the manual shut-off valve before pressure testing gas line at test pressures equal to or less than 1/2 PISG (35mb).

• Use only Wolf Steel approved optional accessories and replacement parts with this appliance using nonlisted accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result in a safety hazard and will void the warranty and certiﬁcation.

• The appliance must not be operated at temperatures below freezing (32ºF/0ºC). Allow the appliance to warm to above freezing prior to operation.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for example in the state of Massachusetts:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.

The installation must conform with local codes or, in absence of local codes, the National Gas and Propane Installation Code CSA B149.1 in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States. Suitable for mobile home installation if installed in accordance with the current standard CAN/CSA Z240MH Series, for gas equipped mobile homes, in Canada or ANSI Z223.1 and NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (35 mb). The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

www.ncertied.org

We suggest that our gas hearth products be installed and serviced by professionals who are certied in the U.S. by the National Fireplace

Institute

(NFI) as NFI Gas

Specialists

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

W415-1768 / B / 08.10.18

1.2 rating plate information

SAMPLE

To convert from one gas to another, consult your Authorized dealer/distributor.

Certiﬁed to Canadian and American National Standards: CSA 2.22-2016 / ANSI Z21.50-2016 for Vented Decorative Gas Appliances Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-2016 / ANSI Z21.50-2016 pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplace. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier W565-0154. Follow installation instructions. Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran W565-0154. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

B30NTR CB30NTR CB30PTR B30PTR B30NTRE CB30NTRE CB30PTRE B30PTRE

Altitude Input Reduced Input P4 Manifold Pressure: 3.5” w.c. (NG) Minimum Supply Pressure: 4.5” w.c. (NG) Maximum Supply Pressure: 7”* w.c. (NG) Pression au Collecteur: 3,5” d’une colonne d’eau (GN) Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN) Pression d’Alimentation Max.: 7”* d’une colonne d’eau (GN)

*Maximum inlet pressure not to exceed 13”.

Minimum clearance to combustible materials:

Sides & back: per standoff spacers for framing and ﬁnishing materials. For non-combustible framing and ﬁnishing materials, see installation manual. Top 0” Floor 0” Sides 0” Back 0”

WARNING:

fast-acting thermocouple. Replace only with a fast-acting thermocouple supplied by Wolf Steel Ltd.

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

Vent top 3” Vent sides & bottom 1” Mantel 12”** Recessed depth 14 1/2”

This appliance uses and requires a

**Maximum horizontal extension: 2”. See installation manual for greater extensions, minimum vent lengths and maximum vent lengths.

MODEL / MODÈLE

0-4500ft (0-1370m)

15,000 BTU/h 10,000 BTU/h

51.7%

Élévation

Alimentation

Alimentation Réduite

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” d’une colonne d’eau (P)

*Pression d’alimentation maximale ne devait pas dépasser 13”.

Dégagements minimaux des matériaux combustibles:

Côtés et arrière: selon les espaceurs de dégagements pour les

matériaux d’ossature selon le manuel du propriétaire pour les

Dessus du conduit d’évent 3” Côtés et dessous du conduit d’évent 1” Tablette 12”** Profondeur d’encastré 14 1/2”

AVERTISSEMENT:

thermocouple à action rapide. Remplacez uniquement avec

un thermocouple à action rapide de Wolf Steel Ltée.

**L’extension horizontale maximale: 2”. Référez au manuel d’installation

pour des extensions plus grandes, les longueurs d’évacuation minimaux et

matériaux de ﬁnition. Dessus 0” Plancher 0”

Côtés 0”

Cet appareil utilise et requiert un

Arrière 0”

maximum.

general information

Insert testing agency

logo

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF HEAT, NOT INTENDED FOR USE AS A HEATING APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY. POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE CERTIFIÉES AVEC L’APPAREIL.

WARNING: Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant. The appliance must be vented using the appropriate Napoleon vent kits. See installation manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing the vent-air intake system. L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et resceller l’évacuation après avoir executer l’entretien du système de prise d’air. Optional fan kit: AUB Ensemble de ventilateur facultatif: AUB Electrical rating: 115V, 60HZ. Less than 12 amperes. Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

Serial Number / N° de Série:

REFERENCE# 161746

B30

W385-1951 / E

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

note:

The rating plate must remain with the appliance at all times. It must not be removed.

1.3 mobile home installation

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plate.

This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. Built in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base. Use appropriate fasteners, inserted through the holes in the base to secure. For free standing products contact your local authorized dealer / distributor for the appropriate securing kit. For mobile home installations, the appliance must be fastened in place. It is recommended that the appliance be secured in all installations. Always turn off the pilot and the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the appliance, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

Conversion Kits

This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (P).

W415-1768 / B / 08.10.18

762mm

general information

1.4 dimensions

SAFETY BARRIER

34 5/8"

879mm

1 13/16"

46mm

355mm

GAS

INLET

30"

14"

170mm

136mm

8 5/8"

6 11/16"

24 3/16"

614mm

324mm

12 3/4"

W415-1768 / B / 08.10.18

102mm

178mm

2.0 venting requirements

WARNING

venting requirements

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W0100067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this gap is maintained. These spaces must not be removed.

This appliance uses a 4” (102mm) exhaust / 7” (178mm) air intake vent pipe system. Refer to the section applicable to your installation.

For safe and proper operation of the appliance, follow the venting instructions exactly. Deviation from the minimum vertical vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes (5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a

ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for 400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the initial installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate constructions such as a chimney as part of the vent system is not permitted.

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab, follow the installation procedure provided with the venting components or on the website for your venting supplier. A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

Vent Manufacturer

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SuperSeal 4DNA Metal-Fab www.mtlfab.com

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following ter-

This template must be used in conjunction with templates 7.1.1 or 7.1.2, depending on

mination kits: wall terminal kit GD-222, GD-222R, or 1/12 to 7/12 pitch roof terminal kit GD-110, 8/12 to 12/12 roof terminal kit GD-111, ﬂ at roof terminal kit GD-112 or periscope kit GD-201 (for wall penetration below grade). With ﬂ exible venting, in

termination shape (i.e. round, or round and square). See appropriate templates folder.

conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD-220 or the 10 foot (3.1m) vent kit GD-330. For stoves only: wall terminal kit GD-175 (venting included).

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20 feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

Starter Adapter Part Number Supplier Website

Horizontal runs may have a 0” rise per foot or 0mm rise per meter however for optimum performance it is recommended that all horizontal runs have a minimum 1/4” rise per foot or 21mm rise per meter using ﬂ exible venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

W415-1768 / B / 08.10.18

WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W010- 0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this gap is maintained. These spaces must not be removed.

This appliance uses a 4” (102mm) exhaust / 7” (178mm) air intake vent pipe system. Refer to the section applicable to your installation.

ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not be combined.

Vent Manufacturer

Starter Adapter Part Number Supplier Website

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SuperSeal 4DNA Metal-Fab www.mtlfab.com

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the initial installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate constructions such as a chimney as part of the vent system is not permitted.

This template must be used in conjunction with templates 7.1.1 or 7.1.2, depending on termination shape (i.e. round, or round and square). See appropriate templates folder.

venting requirements

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air gap all around between the inner liner and outer liner is required for safe operation.

This appliance is certiﬁed for use with a power vent kit. Contact your local authorized dealer for more

If approved for use with a power vent kit, state: “This appliance is certiﬁ ed for use with a

information.

power vent kit. Contact your local authorized dealer for more information.”

2.1 typical vent installation

16" (40.6cm)

minimum

40ft (12m)

8" (203mm)

minimum

24" (61cm)

maximum

Maximum

3ft (1m)

minimum

34 5/8"

(86cm)

W415-1768 / B / 08.10.18

TOP VENT

venting requirements

16" (40.6cm)

minimum

20"

(50.8cm)

Max.

40 ft (12m)

Maximum

3 ft (1m)

minimum

24 3/16" (61.4cm)

minimum plus rise *

24 3/16" (61.4cm)

REAR VENT

* See "venting" section

W415-1768 / B / 08.10.18

30”

MINIMUM

12” MINIMUM

TOP EXIT INSTALLATION

REAR EXIT INSTALLATION

30”

MINIMUM

12” MINIMUM

MAXIMUM 10FT VENT LENGTH

6” (152mm) RISE MINIMUM

20” (50.8cm)

REAR EXIT INSTALLATION

12” MINIMUM

venting requirements

2.2 special vent installations

2.2.1 periscope termination

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when ﬁ nal grading is completed, the bottom air slot is located a minimum 12” (305mm) above grade. The maximum allowable vent length (including both rise and run) is 10’ (3m) for a ﬁ replace and 8’ (2m) for a stove. An insulation sleeve is illustrated in the top vent image below, use only when supplied with the appliance. (The insulation sleeve is not required with a stove appliance)

12" (30.5cm)

minimum

to grade

30" (76.2cm)

minimum

2.2.2 corner termination

The maximum vent length for a corner installation is 20" (50.8cm) of horizontal run, in addition to the 45° offset. In this case zero rise is acceptable. When using rigid venting, it is required to maintain a 6" (152mm) rise. When using ﬂexible venting, see illustrations below.

30" (76.2cm)

minimum

34 5/8"

(87.9CM)

TOP VENTREAR VENT

12" (30.5cm)

minimum

to grade

W415-1768 / B / 08.10.18

6” (152mm)

MAXIMUM

RISE MINIMUM

Flexible Venting Rigid Venting

2.3 minimum air terminal location clearances

Covered balcony applications ††*

venting requirements

= 3 feet

MIN

(0.9m)

INSTALLATIONS

CANADA U.S.A.

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

18”

9” (229mm) ΔClearance to windows or doors that open.

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m) from the center line of the terminal.

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum vertical distance of 15’ (4.6m).

12” (30.5cm)

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

(45.7cm)**

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

0” (0mm)*** 0” (0mm)***

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

3’(0.9m) 3’(0.9m)****

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch or deck.

note:

Wall terminals are for illustration purposes only. Size and shapes may vary.

= 2 x

MAX

ACTUAL

MAX

≤ 15 feet

(4.6m)

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

8’ (2.4m) 8’ (2.4m)

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

6’ (1.8m) 6’ (1.8m)

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Roof must be non-combustible without openings.

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening between the terminal and the open side of the structure.

note:

Clearances are to be in accordance with local installation codes and the requirements of the gas supplier. In their absence, clearances are to be as listed above and are based on national codes.

W415-1768 / B / 08.10.18

For the following symbols used in the venting calculations and examples are: > - greater than > < - less than < H H H V

- combined vertical vent lengths in feet

venting requirements

2.4 venting application ﬂow chart

TOP EXIT

Horizontal Termination

Vertical rise is equal

to or greater than the horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

Horizontal Termination

Vertical rise is less than horizontal run

Horizontal run +

vertical rise to

maximum of 24.75

feet (7.5m)

4.2 times the

vertical rise equal to

or greater than the

horizontal run

REAR EXIT

Vertical Termination

Vertical rise is equal

to or greater than

the horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

Vertical Termination

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of

35 feet (10.7m)

3 times the vertical

rise equal to or

greater than the

horizontal run

Vertical rise is equal

to or greater than

the horizontal run

Horizontal run +

vertical rise to

maximum of 40 feet

(12m)

Vertical rise is less than horizontal run

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m)

3.5 times the

vertical rise equal to

or greater than the

horizontal run

Vertical rise is equal

to or greater than the horizontal run

Horizontal run +

vertical rise to

maximum of 40 feet

2.5 deﬁnitions

- equal to or greater than

- equal to or less than

- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet

- combined horizontal vent lengths in feet

- offset factor: .03 (total degrees of offset - 90°*) in feet

W415-1768 / B / 08.10.18

(12m)

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of 40 feet

(12m)

3 times the vertical

rise equal to or

greater than the

horizontal run

2.6 elbow vent length values

1° 0.03 0.5 12.7 15° 0.45 6.0 152.4 30° 0.9 11.0 279.4 45° 1.35 16.0 406.4 90°* 2.7 32.0 812.8

* The ﬁ rst 90° offset has a zero value and is shown in the formula as - 90°

2.5

(0.8)5(1.5)

7.5

(2.3)

(3.1)

12.5 (3.8)15(4.6)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

17.5 (5.3)20(6.1)

39 (11.9)

REQUIRED

VERTICAL

RISE IN FEET

(METERS)V

HORIZONTAL VENT RUN PLUS OFFSET IN FEET

(METERS) H

Since both formulas are met, this vent conﬁ guration is acceptable.

7.5

(2.3)

(3.1)

12.5 (3.8)15(4.6)

17.5 (5.3)20(6.1)

(METERS) H

FEET INCHES MILLIMETERS

2.7 top exit horizontal termination

(HT) < (VT)

venting requirements

Simple venting conﬁ guration (only one 90° elbow)

40 (12.2)

39 (11.9)

REQUIRED

30 (9.1)

VERTICAL

RISE IN FEET

(METERS)V

20 (6.1)

10 (3.1)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET

For vent conﬁ gurations requiring more than one 90° elbow, the following formulas apply: Formula 1: HT < V

Formula 2: HT + VT < 40 feet (12.2m)

Example: V1 = 3 FT (0.9m)

V2 = 8 FT (2.4m) VT = V1 + V2= 3 FT (0.9m ) + 8 FT (2.4m) = 11 FT (3.4m) H1 = 2.5 FT (0.8m) H2 = 2 FT (0.6m) HR = H1 + H2 = 2.5 FT (0.8m) + 2 FT (0.6m) = 4.5 FT (1.4m) HO = .03 (three 90° elbows - 90°) = .03 (270° - 90°) = 5.4 FT (1.7m) HT = HR + HO = 4.5 FT (1.4m) + 5.4 FT (1.6m) = 9.9 FT (3m) HT + VT = 9.9 FT (3m) + 11 FT (3.4m) = 20.9 FT (6.4m)

Formula 1: HT < V

9.9 FT (3m) < 11 FT (3.4m) Formula 2: HT + VT < 40 FT (12.2m)

20.9 FT (6.4m) < 40 FT (12.2m)

See graph to determine the required vertical

rise VT for the required horizontal run HT.

2.5

(0.8)5(1.5)

7.5

(2.3)

(3.1)

(METERS) H

12.5 (3.8)15(4.6)

17.5 (5.3)20(6.1)

The shaded area within the lines represents

acceptable values for HT and V

90°

W415-1768 / B / 08.10.18

90°

(HT) > (VT)

venting requirements

Simple venting configuration

(only one 90° elbow)

See graph to determine the required vertical rise VT for the required horizontal run HT.

150 (381)

147 (373)

REQUIRED

VERTICAL

100 (254)

RISE IN INCHES

(CENTIMETERS) VT

57 (145)

50 (127)

8 (20.3)

(1.5)

(0.6)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) HT

The shaded area within the lines represents acceptable values for H

For vent configurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H Formula 2: HT + V

< 4.2 V

< 24.75 feet (7.5m)

90°

Example: V

= VT = 6 FT (1.8m)

= 3 FT (0.9m)

= 5 FT (1.5m)

= H

+ H

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7FT (0.8m)

= H

+ V

= 3FT (0.9m) + 5FT (1.5m) = 8FT (2.4m)

+ H

= 8FT (2.4m) + 2.7FT (0.8m) = 10.7FT (3.3m)

= 10.7FT (3.3m) + 6FT (1.8m) = 16.7FT (5.1m)

(3.1)

12.5 (3.8)

(4.6)

19.5 (5.9)

20 (6.1)

and VT

90°

Formula 1: HT < 4.2 V

4.2 VT = 4.2FT (1.3m) x 6FT (1.8m) = 25.2FT (7.7m) Formula 2: HT + V

16.7 FT (5.1m) < 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

< 24.75 FT (7.5m)

90°

Example: V

= 4 FT (1.2m)

= 1.5 FT (0.5m)

= V

+ V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= H

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

Formula 1: HT < 4.2 V

4.2 VT = 4.2 FT (1.3m) x 5.5 FT (1.7m) = 23.1 FT (7m)

= 4 FT (1.2m) + 1.5 FT (0.5m) = 5.5 FT (1.7m)

+ H2 + H

+ H

= 13.6 FT (4.2m) + 5.5 FT (1.7m) = 19.1 FT (5.8m)

+ H4 = 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

= 5.5 FT (1.7m) + 8.1 FT (2.5m) = 13.6 FT (4.2m)

13.6 FT (4.2m) < 23.1 FT (7m) Formula 2: HT + V

19.1 FT (5.8m) < 24.75 FT (7.5m)

< 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

90°

W415-1768 / B / 08.10.18

2.8 rear exit horizontal termination

Simple venting configuration

(HT) < (VT)

(only two 90° elbows)

venting requirements

See graph to determine the required vertical rise V

40 (12.2)

38.3 (11.7)

horizontal run H

for the required

For vent configurations requiring more than two 90° elbows, the following formulas apply:

Formula 1: H Formula 2: HT + V

Example:

= 9 FT (2.7m)

= 6 FT (1.8m)

= V

V H H H H H H H

+ V

= 3 FT (0.9m)

= 2 FT (0.6m)

= 1.5 FT (0.5m)

= H

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

+ H2 + H

+ H

= 14.6FT (4.5m) + 15FT (4.6m) = 29.6 FT (9m)

Formula 1: H

14.6 FT (4.5m) < 15 FT (4.6m) Formula 2: HT + V

29.6 FT (9m) < 40 FT (12.2m)

Since both formulas are met, this vent configuration is acceptable.

REQUIRED

VERTICAL

(METERS) V

The shaded area within the lines represents acceptable values for H

< V

< 40 feet (12.2m)

= 9FT (2.7m) + 6FT (1.8m) = 15FT (4.6m)

= 3FT (0.9m) + 2FT (0.6m) + 1.5FT (0.5m) = 6.5FT (2m)

= 6.5FT (2m) + 8.1FT (2.5m) = 14.6FT (4.5m)

< V

< 40 FT (12.2m)

30 (9.1)

RISE IN

20 (6.1)

FEET

10 (3.1)

1.6 (0.5)

2.5

(0.8)5 (1.5)

1.6

(0.5)

7.5

(2.3)

(3.1)

12.5

(4.6)

17.5 (5.3)

(3.8)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

and HT

90°

(6.1)

W415-1768 / B / 08.10.18

(HT) > (VT)

venting requirements

Simple venting configuration

(only two 90° elbows)

See graph to determine the required vertical rise V

12.5 (3.8)

12.25 (3.7)

required horizontal run H

for the

REQUIRED

VERTICAL RISE IN

8.3 (2.54)

FEET

(METERS)V

(1.68)

(0.3)

5.5

4.2 (1.3)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

The shaded area within the lines represents acceptable

For vent configurations requiring more than two 90° elbows, the following formulas apply:

Formula 1: H Formula 2: HT + V

< 3.5V

< 24.75 feet (7.5m)

Example:

= 4 FT (1.2m)

= 1.5 FT (0.5m)

= V

+ V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= H1+ H2+H3+H4= 2FT(0.6m) + 1FT(0.3m) + 1FT(0.3m) + 1.5FT(0.5m) = 5.5 FT(1.7m)

= .03 (four 90° elbows + one 45° elbow - 90°)

= .03 (90 + 90 + 90 + 90 + 45 - 90) = 9.45 FT (2.9m)

= H

+ V

Formula 1: H

3.5VT = 3.5FT (1.1m) x 5.5FT (1.7m) = 19.25FT (5.9m)

14.95 FT (4.6m) < 19.25 FT (5.9m)

Formula 2: HT + V

20.45 FT (6.2m) < 24.75 FT (7.5m)

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

+ H

= 5.5FT (1.7m) + 9.45FT (2.9m) = 14.95FT (4.6m)

= 14.95FT (4.6m) + 5.5FT (1.7m) = 20.45FT (6.2m)

< 3.5V

< 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

2.5

(0.8)5 (1.5)

(0.3)

values for H

(1.1)

7.5

12.5

17.5

(2.3)

(3.1)

(3.8)

3.5

and HT

(4.6)

(5.3)

19.25 (5.9)

(6.1)

90°

W415-1768 / B / 08.10.18

2.9 top and rear exit vertical termination

for the

(HT) < (VT)

Simple venting configurations.

REQUIRED

VERTICAL RISE

IN FEET

(METERS)V

venting requirements

See graph to determine the required vertical rise V

required horizontal run HT.

40 (12.2)

30 (9.1)

20 (6.1)

10 (3.1)

3 (0.9)

(1.5)

(3.1)

(4.6)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET

(METERS) H

The shaded area within the lines represents acceptable

values for H

and HT

For vent configurations requiring one or more 90° elbows (top exit) or one or more 90° elbows (rear exit), the following formulas apply:

Formula 1: H Formula 2: HT + V

< V

< 40 feet (12.2m)

Example:

= 5 FT (1.5m)

= 6 FT (1.8m)

= 10 FT (3.1m)

= V

+ V2 + V

= 8 FT (2.4m)

= 2.5 FT (0.8m)

= H1+ H2 = 8FT (2.4m) + 2.5FT (0.8m) = 10.5FT (3.2m)

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ H

+ V

= 18.6FT (5.7m) + 21FT (6.4m) = 39.6FT (12.1m)

= 5FT (1.5m) + 6FT (1.8m) + 10FT (3.1m) = 21 FT (6.4m)

= 10.5FT (3.2m) + 8.1FT (2.5m) = 18.6FT (5.7m)

(6.1)

Formula 1: H

18.6 FT (5.7m) < 21 FT (6.4m) Formula 2: HT + V

39.6FT (12.1m) < 40 FT (12.2m)

< 3.5V

< 40 FT (12.2m)

Since both formulas are met, this vent configuration is acceptable.

W415-1768 / B / 08.10.18

(HT) > (VT)

need to be established to satisfy both formulas.

Example:

Since both formulas are met, this vent conﬁguration is acceptable.

venting requirements

Simple venting configurations.

REQUIRED

VERTICAL

RISE IN

FEET

(METERS)V

See graph to determine the required vertical rise V

required horizontal run HT.

20 (6.1)

19 (5.8)

10 (3.1)

3 (0.9)

(1.5)

(3.1)

(4.6)

(6.1)

(7.6)

for the

(9.1)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS)H

The shaded area within the lines represents acceptable

values for HT and HT

For vent configurations requiring more than two 90° elbows (top exit) or one 90° elbow (rear exit), the following formulas apply:

Formula 1: H Formula 2: HT + V

Example: V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= V

= 6 FT (1.8m)

= 2 FT (0.6m)

= H

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

Formula 1: H

3.5 V

16.1FT (4.9m) < 13.5 FT (4.1m)

< 3 V

< 40 feet (12.2m)

+ V2 + V3 = 2FT (0.6m) + 1FT (0.3m) + 1.5FT (0.5m) = 4.5 FT (1.4m)

+ H

= 6FT (1.8m) + 2FT (0.6m) = 8 FT (2.4m)

+ H

= 8FT (2.4m) + 8.1FT (2.5m) = 16.1FT (4.9m)

= 16.1FT (4.9m) + 4.5FT (1.4m) = 20.6FT (6.3m)

< 3.5 V

= 3FT (0.9m) x 4.5FT (1.4m) = 13.5 FT (4.1m)

90°

Since this formula is not met, this vent configuration is unacceptable. Formula 2: HT + V

16.1FT (4.9m) < 13.5 (4.1m)

< 40 FT (12.2m)

Since only formula 2 is met, this vent configuration is unacceptable and a new fireplace location or vent configuration will

= 1.5 FT (0.5m)

= 5 FT (1.5m)

= V

+ V2 = 1.5FT (0.5m)+ 5FT (1.5m) = 6.5 FT (2m)

= 1 FT (0.3m)

= 10.75 FT (3.3m)

= H

+ H2 + H3 = 1FT (0.3m) + 1FT (0.3m) + 10.75FT (3.3m) = 12.75FT (3.9m)

= .03 (three 90° elbows + one 45° elbow - 90°)

= .03 (270° + 45° - 90°) = 6.75 FT (2.1m) H

= H

+ H

+ V

= 12.75FT (3.9m) + 6.75FT (2.1m) = 19.5 FT (5.9m)

= 19.5FT (5.9m) + 6.5FT (2m) = 26 FT (7.9m)

Formula 1: HT < 3 V 3 V

19.5FT (5.9m) = 19.5FT (5.9m)

= 3FT (0.9m) x 6.5FT (2m) = 19.5FT (5.9m)

Formula 2: H

+ V

< 40 FT (12.2m)

26 FT (7.9m) < 40 FT (12.2m)

W415-1768 / B / 08.10.18

90°

45°

90°

venting requirements

DEFLECTOR

JOINT D’ÉTANCHÉITÉ

COLLET D’ÉVACUATION

2.10 rear exit

WARNING

• Failure to create a seal to the ﬁrebox with the exhaust collar assembly will cause the appliance to function improperly and can cause injury or property damage.

A. Remove the safety barrier and glass front, refer to "safety

barrier & door removal/installation" section.

B. Remove the contents from the ﬁrebox and set aside, you will

need the exhaust ﬂue collar from the top of the log carton.

C. To ease assembly, remove the four hex head screws

securing the deﬂector from inside the top front of the ﬁrebox, refer to Figure 1.

D. Place the gasket (provided) over the 4" (102mm) ﬂue collar

assembly and bend along perforation.

E. From inside the ﬁrebox, insert the 4" (102mm) ﬂue collar through the back

of the ﬁrebox. Install the rear exit shield onto the 4" (102mm) ﬂue collar, see "rear exit shield" section for installation instructions.

F. Secure the ﬂue collar assembly, gasket and rear exit shield using the four hex

head 3/8" thread cutting screws, refer to Figure 2.

note:

Do not overtighten. The gasket needs only to be snug against the ﬁrebox.

G. Reattach the deﬂector using the four screws and

install the log set, glass door and safety barrier.

H. Install the 7" collar assembly, complete with

gasket, onto the rear panel around the 4" (101.6mm) collar with the screws provided (FIG

3).

Fig. 1

Fig. 2

Fig. 3

GASKET

INTAKE COLLAR

ASSEMBLY

2.11 rear exit shield (for rear vent only)

A. Remove the safety barrier assembly and door from the appliance, refer to the “safety barrier & door removal / installation” section of the manual for detailed instructions.

B. Loosen the two screws, that secure the exhaust plate, and slide the shield in place by sliding its slotted openings behind the screwheads, tighten the two previously loosened screws. Refer to the illustration .

C. Reinstall the door and safety barrier assembly on the appliance, see to the “safety barrier & door removal / installation” section.

note:

This shield is used to block the view through the venting to the outdoors.

W415-1768 / B / 08.10.18

INTAKE COLLAR

ASSEMBLY

GASKET

OUTER COVER

INNER

OUTER

DEFLECTOR

venting requirements

2.12 top exit

WARNING

• Failure to install the cover plate and gasket will cause the appliance to function improperly and can cause injury or property damage.

This appliance is factory shipped as a rear vent model equipped with a #50 burner oriﬁce. This oriﬁce size is suitable for rear vent installations with 0" vertical rise only. For top exit applications, the main burner oriﬁce should be changed to the #49 burner oriﬁce (supplied) for natural gas. For propane models, the appliance is converted to a #58 burner oriﬁce for rear vent applications or a #57 burner oriﬁce for top vent applications.

A. Remove the safety screen and glass front, refer to " SAFETY

SCREEN / DOOR REMOVAL AND INSTALLATION" section.

B. Remove the contents from the ﬁrebox and set aside, you will

need the exhaust collar from the top of the log carton.

C. To ease assembly, remove the four hex head screws securing

the deﬂector from inside the top front of the ﬁrebox.

D. Remove the single screw from the outer cover on the

back of the appliance.

E. Remove the four screws on the 7" (178mm) intake collar

assembly; set the intake collar and gasket aside. Careful not to damage gasket.

F. Remove the single screw from the outer cover with

knockout intact, on the top of the appliance and set aside.

G. Remove the inner cover plate and gasket by removing the

four screws. Reinstall the inner cover plate and gasket onto the back of the appliance.

H. Take the outer cover (with knockout intact) and secure

onto the back of the appliance.

I. Remove and discard the 1 1/2" thick batt of insulation

from the top opening.

J. Place the 7" (178mm) intake collar and

gasket onto the top of the appliance and secure with the four screws.

K. Reinstall the outer cover (without knock

out) over the 7" (178mm) exhaust collar assembly and secure.

L. From inside the ﬁrebox, install the 4"

(102mm) exhaust collar up through the top of the ﬁrebox and secure with the the four hex head 3/8" thread cutting screws. NOTE:

Do not overtighten. The gasket needs only to be snug against the ﬁrebox.

M. Reattach the top deﬂector, log set, glass door

and safety screen.

COVER

PLATE

(without

knockout)

GASKET

INTAKE COLLAR

EXHAUST FLUE COLLAR

ASSEMBLY

OUTER COVER

COVERPLATE

GASKET

W415-1768 / B / 08.10.18

3.0 rough framing

WARNING

note:

When using optional ﬁ nishing accessories, the framing dimensions and ﬁ nishing materials may differ from what is outlined in the section below; refer to the leaﬂ et instructions supplied in the accessory kit for speciﬁ c framing and ﬁ nishing speciﬁ cations.

• Risk of ﬁ re!

• In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the appliance body, it is recommended that the walls of the appliance enclosure be “ﬁ nished” (i.e. drywall / sheetrock), as you would ﬁ nish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the cavity.

• Do not notch the framing around the appliance stand offs. Failure to maintain air space clearance may cause over heating and ﬁ re. Prevent contact with sagging or loose insulation or framing and other combustible materials. Block opening into the chase to prevent entry of blown-in insulation. Make sure insulation and other materials are secured.

• When constructing the enclosure, allow for ﬁ nishing material thickness to maintain clearances. Framing or ﬁ nishing material closer than the minimums listed must be constructed entirely of non-combustible materials. Materials consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof are suitable. Materials that are reported as passing ASTM E136, standard test method for behaviour of materials in a vertical tube furnace at 1382ºF (750ºC) and UL763 shall be considered non-combustible materials.

• Minimum clearance to combusibles must be maintained or a serious ﬁ re hazard could result.

• The appliance requires a minimum enclosure height. Measure from the appliance base.

• If steel stud framing kits with cement board are provided, or speciﬁ ed in the installation instructions, they must be installed.

• If speciﬁ ed in the installation instruction, ﬁ nishing must be done using a non-combustible board, ceramic tile, marble, etc. Do NOT use wood or drywall. Any ﬁ re rated drywall is not acceptable.

rough framing

It is best to frame your appliance after it is positioned and the vent system is installed. Frame to local building codes.

It is not necessary to install a hearth extension with this appliance.

When roughing in the appliance, raise the appliance to accommodate for the thickness of the ﬁnished ﬂoor materials, i.e. tile, carpeting, hard wood, which if not planned for will interfere with the opening of the lower access door and the installation of many decorative ﬂashing accessories.

Combustible materials may be installed ﬂush with the front of the appliance but must not cover any of the black face-areas of the appliance. Non-combustible material (brick, stone or ceramic tile) may protrude in these areas.

W415-1768 / B / 08.10.18

Do not put objects in front of the appliance

(minimum distance of 4 feet)

rough framing

3.1 minimum framing dimensions

SIDE WALL

2”

(51mm)

30 1/2”

(77.5cm)

14 1/2”

(36.8cm)

29 1/2”

(75cm)

30 1/2”

(77.5cm)

41 3/4”

(106

)

* HORIZONTAL VENT SECTIONS: A minimum of 1" (25mm) at the bottom and sides and 3" (76mm) at the top of the vent pipe on all horizontal runs to combustibles is required. Use ﬁrestop spacer W010-1777 (supplied).

NOTE: The minimum clearances from the top of the horizontal vent pipe to combustible materials may be reduced from 3"(76mm) to 1"(25mm) in those installations with a minimum 38" (965mm) vertical vent rise made immediately off the ﬁreplace collar.

* VERTICAL VENT SECTIONS: A minimum of 1" (25mm) all around the vent pipe on all vertical runs to

combustibles is required except for clearances in appliance enclosures. See "minimum enclosure clearances" section. Use ﬁrestop spacer W500-0096 (not supplied).

W415-1768 / B / 08.10.18

3.2 minimum enclosure clearances

COMBUSTIBLE

NON-COMBUSTIBLE

TOP VENT

rough framing

54"

[1372mm]

CEILING

(MIN)

50 1/2"

[1283mm]

15 5/8"

3" [76mm]

[403mm]

3" [76mm] MINIMUM *

[51mm]

BRICK

3" [76mm]

[25mm]

42 5/8"

[1083mm]

0” (0MM) IF NON-COMBUSTIBLE FINISHING IS USED SUCH AS BRICK AND STONE.

MINIMUM

14 1/2"

PLUS RISE*

[368mm]

[25mm]

TOP EXIT ENCLOSURE

The appliance requires a minimum non-combustible enclosure height of 50 1/2" (1283mm). For temperature requirements, the enclosure space around and above the appliance must be left unobstructed.

NOTE: The vent shield is telescopic and must be adjusted to shield the full depth of combustible wall penetration.

* See "MINIMUM FRAMING DIMENSION" section for details on reducing vent pipe top clearances.

These parameters also apply to the illustrations found in the "MINIMUM ENCLOSURE CLEARANCES" section.

W415-1768 / B / 08.10.18

41 5/8"

[105.7cm]

rough framing

REAR VENT

For rear vent termination not exceeding 10" (254mm) of horizontal vent run.

NON-COMBUSTIBLE

41 5/8"

[105.7cm]

34 5/8"

[87.9cm]

[178mm]

COMBUSTIBLE

BRICK

[76mm]

[25mm]

0” (0MM) IF NON-COMBUSTIBLE FINISHING IS USED SUCH AS BRICK AND STONE.

24 3/16" [61.4cm]

MINIMUM

PLUS RISE*

1"-10"

[25mm-254mm]

VENT RUN

REAR EXIT ENCLOSURE

The appliance requires a minimum enclosure height of 41 5/8" (1057mm). For temperature requirements, the enclosure space around and above the appliance must be left unobstructed.

NOTE: The vent shield is telescopic and must be adjusted to shield the full depth of combustible wall penetration.

* See "VENTING" section.

W415-1768 / B / 08.10.18

MAXIMUM REAR VENT CLEARANCES (EXAMPLE 1)

NON-COMBUSTIBLE

COMBUSTIBLE

11 1/2"

[292mm]

rough framing

BRICK

0” (0MM) IF

[76mm]

NON-COMBUSTIBLE FINISHING IS USED SUCH AS BRICK AND STONE.

41 5/8"

[178mm]

[105.7cm]

34 5/8"

[87.9cm]

[25mm]

24 3/16"

24 1/8”

(61.4cm)

[61.3cm]

MINIMUM

PLUS RISE*

10"-20"

[254mm-508mm]

VENT RUN

REAR EXIT ENCLOSURE

The appliance requires a minimum enclosure height of 41 5/8" (1057mm). For temperature requirements, the enclosure space around and above the appliance must be left unobstructed.

NOTE: The vent shield is telescopic and must be adjusted to shield the full depth of combustible wall penetration.

W415-1768 / B / 08.10.18

[178mm]

41 5/8"

[105,7cm]

34 5/8"

[87,9cm]

rough framing

MAXIMUM REAR VENT CLEARANCES (EXAMPLE 2)

11 1/2"

[292mm]

[76mm]

0” (0MM) IF NON-COMBUSTIBLE FINISHING IS USED SUCH AS BRICK AND STONE.

41 5/8"

[178mm]

[105.7cm]

34 5/8"

[87.9cm]

COMBUSTIBLE

NON-COMBUSTIBLE

[25mm]

BRICK

24 3/16"

24 1/8”

(61.4cm)

[61.3cm] MINIMUM PLUS RISE*

10"-20"

[254mm-508mm]

VENT RUN

REAR EXIT ENCLOSURE

The appliance requires a minimum enclosure height of 41 5/8" (1057mm). For temperature requirements, the enclosure space around and above the appliance must be left unobstructed.

NOTE: The vent shield is telescopic and must be adjusted to shield the full depth of combustible wall penetration.

W415-1768 / B / 08.10.18

rough framing

note:

For heavier ﬁnishing materials such as marble, we recommend adding extra support to the frame. Ensure there is adequate ﬂoor support for the appliance and ﬁnishing material.

Before framing your appliance, determine vent requirements before deciding the ﬁnal location of the appliance. After rough framing, place the appliance in its ﬁnal position.

Ref Minimum rough framing dimensions

A B

* Based on 1/2” ﬁnishing material thickness.

14 1/2”* (36.8cm)

30 1/2” (77.5cm)

W415-1768 / B / 08.10.18

4.0 venting installation

WARNING

venting installation

• Ensure to unpack all loose materials from inside the ﬁ rebox prior to connecting the gas and electrical supply

• If your appliance is supplied with a remote, ensure the remote receiver is in the “OFF” position prior to connecting the gas and electrical supply to the appliance.

• For safe and proper operation of the appliance, follow the venting instructions exactly.

• The appliance exhaust ﬂ ue collar must be sealed using Mill Pac. All exhaust and intake vent pipe joints must be sealed using red RTV high temp silicone sealant (W573-0002) (not supplied) or black high temp Mill Pac (W573-0007) (not supplied).

• If using pipe clamps to connect rigid vent components, a minimum of 3 screws must also be used to ensure the connection cannot slip off.

• Do not clamp the ﬂ exible vent pipe.

• Risk of ﬁ re, explosion, or asphyxiation. Improper support of the entire venting system may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions.

• Risk of ﬁ re, do not allow loose materials or insulation to touch the vent pipe. Remove insulation to allow for the installation of the attic shield and to maintain clearances to combustibles.

• Do not ﬁ ll the space between the vent pipe and enclosure with any type of material. Do not pack insulation or combustibles between ceiling ﬁ restops. Always maintain speciﬁ ed clearances around venting and ﬁ restop systems. Install wall shields and ﬁ restops as speciﬁ ed. Failure to keep insulation or other materials away from vent pipe may cause ﬁ re.

For optimum performance, it is recommended that all horizontal runs have a minimum of 1/4" (6mm) rise per foot using ﬂexible venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

W415-1768 / B / 08.10.18

+ 106 hidden pages

Napoleon B30NTRE1 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual