Page 1
$50('
www.ealarm.com.my
5($'<
6<67(0
9
),5(
Using Your
XP-600
Security System
$&
=21(
=21(
=21(
=21(
=21(
=21(
NAPCO
Page 2
Introduction
www.ealarm.com.my
Table of Contents
Keypad Controls and Indicators ................................ 4
Arming your System (When Leaving) ....................... 5
Protecting Yourself While Home ............................... 6
Emergency Keys ....................................................... 7
Disarming the System ............................................... 8
Silencing an Alarm..................................................... 8
Resetting a Fire Alarm............................................... 8
Fire Protection .......................................................... 9
Special Functions .................................................... 11
System Troubles ....................................................... 12
Programming User Codes ......................................... 14
Glossary ................................................................... 15
Important - Test Your System Weekly !
1
Bell / Battery Test
Test your bell or siren by pressing
will cause the bell, or siren to sound for 2 seconds and also
initiate a test of the battery .
2
Central Station Communication Test
(This test should only be performed on weekends or at a
time designated by your alarm company)
1. Notify Central Station of the impending test.
followed by .This
System Information
Central Station Phone Number: ____________________
Central Station Account Number: ____________________
For Service Call: ____________________
Entry Delay: ____________________
Exit Delay: ____________________
Alarm Time-out: ____________________
2. Secure all zones to light Ready Light on your keypad.
3. Enter your user code to Arm the system.
4. Violate your alarm by opening a window / door etc.
5. The siren or bell should sound and the system will send
the alarm signals to the Central Station
6. Enter you user code to silence the bell or sounder.
7. Call Central Station to insure that the alarm signals were
received properly.
3
Page 3
Keypad Controls and Indicators
(
g
www.ealarm.com.my
Key Used to enable
special functions and options. Press
the corresponding Special Function number Option (See Special Functions, Page 11)
Bypass Key Used to
bypass zones. Press
Bypass and the corresponding zone number,
and then Arm system.
Emergency Keys Press
simultaneously to signal
an emergency condition.
Press
$+$
3+3
gency. (Programmable)
4
and then
)+)
for Fire,
for Auxiliary or
for Police Emer-
Numerical Keys 1-9, 0. Used to enter
User Codes, Zone numbers, etc.
99 Key Press to display any present
System troubles. Only available when
99 System Light is lit.
(See System troubles, Page 12)
$50('
5($'<
9
),5(
$&
=21(
=21(
=21(
=21(
=21(
=21(
NAPCO
6<67(0
Armed Li
and will flash when system is in Alarm
Ready Light
and system is ready to be Armed.
99 System Light will light and the Keypad sounder
will pulse to indicate that a system trouble is present.(See System Troubles, Page12)
Fire Alarm Light
sounder will beep when system is in a Fire Alarm
Condition (See Silencing a fire Alarm, Page 8)
AC Light
is present.
Zone Lights
that the corresponding Zone is open, and will
flash to indicate a zone in alarm.
Key - used to reset Fire Zone, clear miss-
entered codes, reset Alarm Memory, etc..
will light when system is Armed,
ht
will light when all zones are secure
will flash and the Keypad
will light to indicate that AC Power
1 through 6) will light to indicate
Page 4
g
g
g
ARMED
www.ealarm.com.my
READY
SYSTEM
FIRE
AC
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
Arming Your System
Arming Your System When Leaving
1
Before arming your system, make sure the Green
ective zones are secure. If any zones are open, the correspondin
zones before proceedin
2
Enter your user code. The Green
•
If you make a mistake enterin
• If the FIRE light is on, the Fire zone has not been properly reset. Press
(See Silencing a Fire Alarm, page 8)
3
Leave the premises through the Exit/Entry door. If the keypad gives a steady tone you have taken
too long. Enter your code again to disarm system and then re-enter code and leave.
. If any zones cannot be secured, see Bypassing Zones below.
Ready
light will go out, the Red
your code, press
Easy Arm
The Easy Arm feature allows the system to be armed by simply pressing
This will allow the easy arming of the system by someone who is not a regular system user.
Bypassing Zones
If an open zone cannot be immediately fixed it can be left unprotected, or
system is Armed. To Bypass a zone:
1
Press
2
Enter your user code. The Green Ready light will go out and the Red Armed light will light.
3
Leave the premises through the Exit/Entry door.
followed by the zone number to be Bypassed. The Bypassed Zone’s light will flash slowly.
Ready
light is ON. This indicates that all of your prot-
Zone light will be ON. Secure these
Armed
and re-enter the code.
light will light.
followed by .
Bypassed
and enter the code.
, while the rest of the
When the system is subsequently disarmed, all bypassed zones will be reset, ready to be armed again.
If it is necessary to bypass any inoperative zone(s), it is important to have the zone(s) repaired as soon as
possible. A bypassed zone does not provide any protection, compromising system security.
5
Page 5
g
g
g
g
y
Arming Your System
www.ealarm.com.my
Protecting Yourself While at Home
1
Before arming your system, make sure the Green
protective zones are secure. If any zones are open, the correspondin
those zones before proceedin
2
Enter your user code. The Green
3
Before your exit delay expires, press
ARMED
READY
SYSTEM
FIRE
AC
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
as motion sensors, and allowin
bypassed zones will flash slowly.
•
Your system may have been programmed for Automatic Interior Bypass , in which case it will recognize
that you have not left the premises and will automatically bypass any interior zones.
Instant Mode
Pressing
done in the evening when all family members are home for the night. Instant Mode can be activated at any
time after the system has been armed. The Red Armed light will flash rapidly while in the Instant Mode.
Easy Exit
Your System may have been programmed to allow Easy Exit, which allows a user to exit the premises
with the system armed. By pressing
zone for 3 minutes. This will allow, for example, an early morning commuter to exit the house in the
morning, without having to disarm and rearm the system, waking the family.
(optional)
followed by
Ready
light is ON. This indicates that all of your
Zone light will be ON. Secure
.
Ready
free movement throughout the premises. The Zone light of any
will cancel the Entry delay , activating the “Instant” mode. This is typically
light will go out, and the Red
to bypass any interior zones, deactivating devices such
followed by , the protection is removed from the Exit/ Entry
Armed
light will light.
Arming With a System Trouble Present
If the XP600 has a system trouble present, the
pulsin
press
For more information, refer to page 12. Note: System troubles should be repaired as soon as possible.
6
. If you cannot immediately clear the system trouble, the system can still be armed. Simpl
to view the trouble, press
(the
9 System Light is Lit)
9
SYSTEM l
9
again to reset the trouble and then arm the system.
ight will be lit and the keypad sounder
Page 6
www.ealarm.com.my
%
Fire
Emergency
Enabled?
Emergency Buttons
Emergency Conditions
Yes No
Auxiliary
Emergency
Enabled?
Yes No
Police
Emergency
Enabled?
Yes No
Ambush
Alarm
Enabled?
Yes No
The three sets of emergency buttons, if programmed, are always active whether the system is ar med
or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated
when the two respective buttons are pressed at the same time.
Fire Alarm:
Auxiliary Alarm: Simultaneously press
Police Emergency: Simultaneously press
Ambush Alarm
In the event that you are forced by an intruder to disarm your system, the ambush alarm can be
activated. Disarming the system with the Ambush Code will cause the system to disarm and
simultaneously send a silent ambush alarm signal to Central Station. If your system has the Ambush
feature enabled, the code assigned as the User 6 code will function as your Ambush Code.
Simultaneously press
station of a fire emergency, if so programmed.
emergency, if so programmed.
(The nature of this emergency alarm is to be determined by the installer)
the central station of a fire emergency, if so programmed.
+
+
+
to sound a fire alarm, and to alert the central
to alert the central station of an auxiliary
to sound a police emergency alarm, and to alert
7
Page 7
g
g
g
g
g
g
g
Disarming Your System / Silencing an Alarm
www.ealarm.com.my
Disarming Your System when Returning
1
Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to
disarm the system before your Entry Delay time expires.
2
Enter your user code. The Red
Note: If you make a mistake enterin
Armed
light will go out, indicating that the system has been disarmed.
your code, press the key and re-enter the code.
ARMED
READY
SYSTEM
FIRE
AC
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
8
Alarm Indication
If the Red Armed light is flashing rapidly, an alarm occurred while you were away.
For your own protection, leave immediately and call authorities from a nei
Silencing an Alarm
In the event that the system goes into alarm due to a violated burglary zone, the bell or siren will sound and
the keypad sounder will also activate. To silence the system, enter your User code. The zone li
zone which went into alarm will continue to flash until
Silencing a Fire Alarm
In the event that the Fire alarm activates due to an violated smoke or fire detector, the bell or siren will
sound a distinct pulsatin
will emit a pulsin
1
If a fire is in progress, evacuate the premises immediately!Call the Fire Department from an outside phone.
2
If there is no evidence of a fire, enter your User Code. The bell or siren will silence, and the FIRE light on
the keypad will stop flashin
3
Determine which device went into alarm. If you are protected by smoke detectors, the light on the active
detector will be lit. Once it is determined which smoke detector is in alarm, press
4
If the Fire zone has reset properly, the FIRE light on the keypad should go out in approx. 30 seconds
If it does not
service.
tone. If a Fire Alarm does occur:
o out, press
tone. The Red
Proceed with caution!
hbor’s phone .
is pressed to reset the alarm memory.
FIRE
light on the keypad will be flashing, and the keypad sounder
but will still be lit.
to reset the fire zone.
again in a few minutes. If the FIRE light still does not go out, call for
ht of the
Page 8
Special Functions
www.ealarm.com.my
By pressing
followed by the appropriate key, (do not press simultaneously) these special functions and features
can be enabled:
The Easy Arm feature allows the system to be armed by
pressing
Easy Arm (when system is disarmed)
followed by . This will allow the easy
arming of the system by someone who is not a regular
system user.
Easy Exit (when system is armed)
This function (if programmed) allows an occupant to leave
the premises without disarming the system. Pressing
followed by
while the system is armed will start a 3
minute period, during which you can leave through the
Exit/ Entry door.
Pressing
Bell / Battery Test
followed by will cause the bell, or siren to
sound for 2 seconds. This will also initiate a test of your
battery to make sure it is adequately charged. The XP-600
also performs an automatic battery test very 24 hours
If programmed, pressing
Access Output
followed by
will activate
the Access Output which may be configured to open a door
strike, turn on lighting, or activate some other special
feature your installer has provided.
Pressing
Instant Mode
followed by will cancel the Entry delay
and put the system into the “Instant” mode. This is typically done in the evening when all family members are home
for the night. When the system is disarmed, the Instant
mode will be canceled.
Pressing
Chime Mode On / Off
followed by
will activate / deactivate the
door chime. Activating this feature will cause any door
to beep the keypad sounder when it is opened.
Pressing
Program Mode
followed by will enable the “Program
Mode”, which will allow you to program and erase user
codes. (see Programming user codes, page 14)
Pressing
Keypad Sounder On / Off
followed by will deactivate / activate the
keypad sounder, depending on its present state. By
activating sleep mode on a keypad installed in a bedroom,
for example, you effectively turn off that keypad’s sounder.
However, any other keypads on the system will still sound
normally.
11
Page 9
9
www.ealarm.com.my
System Troubles
The XP600 is constantly monitoring its own components, as well as all critical servic es, such as AC Power
and the Telephone line, to insure that it is always ready to provide the protection for which it was designed.
When a system trouble does occur, it will caution you by lighting the y ellow
keypad buzzer. If you cannot immediately clear the system trouble, the system can still be us ed. Simply
press
In order to determine the nature of the trouble, pr es s
ARMED
READY
SYSTEM
FIRE
AC
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
the number of the illuminated zone light. Refer to the following table to determ ine the cause of the trouble.
If there is more than one trouble to be viewed, pressing
99SYSTEM mode if there are no additional troubles to view.
Keypad Beeps or
SYSTEM
9
9
1
1
1
Beep
1
2
Beeps
to view the trouble as described below, and then arm the system.
, count the number of k eypad beeps and observe
will scroll to the next, and then exit the
Zone lightONSystem Trouble
Failure
Condition
system transformer is plugged into AC receptacle and check
circuit breaker, otherwise call installing company for service.
partially depleted and must be recharged by the control
panel. If the trouble does not go away in 24 hours, call installing company for service.
The system was not able to report to central station. If this is
due to a temporary interruption in the telephone service, the
trouble can be cleared when the service is restored by pressing
temporarily interrupted, the trouble will clear it is when restored. Otherwise, call installing company for service.
pany for service.
. Otherwise, call installing company for service.
Beep
Beep
Beep
Flashes
1 AC Power Failure This trouble will occur if AC power is not present. Make sure
2 Low Battery If there has been a recent power failure, the battery may be
3 Communication
4 Telephone Line Cut The telephone line has failed. If telephone service has been
1 Bell/Siren Trouble There is a problem with the Bell or Siren. Call installing com-
99SYSTEM light and beeping the
Action
12
Page 10
Keypad Beeps or
www.ealarm.com.my
SYSTEM
9
9
2
Beeps
2
Beeps
Flashes
Zone lightONSystem Trouble
2 Fire Trouble A problem has been detected in the Fire Circuit.
3 Wireless Receiver
Trouble
ARMED
READY
SYSTEM
FIRE
AC
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
2
Beeps
3
Beeps
4
Beeps
5
Beeps
6
Beeps
4 Wireless Receiver
Jam
1-6 Wireless
Transmitter Low
Battery
1-6 Wireless
Transmitter
Supervisory Failure
1-4 Wireless Smoke
Detector Low Battery
1-4 Wireless Smoke
Detector Supervisory Failure
7
Beeps
1-6 Zone Trouble Call installing company for service.
Condition
9
System Troubles
Action
Call installing company for service.
A problem has been detected with the wireless receiver.
Call installing company for service.
A problem has been detected with a wireless receiver.
Call installing company for service.
The battery in a wireless transmitter is low and should be re-
placed. This transmitter is on the zone corresponding to the number of the lit zone light. The replacement battery for the GEMTrans2 door/window transmitter, GEM-PIR motion detector and
GEM-GB glass break detector is the Duracell DL123A. (2 required for the GEM-PIR and GEM-GB.) The GEM-DT Dual Technology Sensor requires C-Cell Duracell MN1400 batteries(4).
Warning: Replace batteries only with the same type as specified
above. Use of another bat tery may pres ent a risk of fire or ex plosion.
Do not recharge or disassemble battery, or dispose of i n fire.
A problem has been detected with a wireless transmitter.
Call installing company for service
The battery in a wireless smoke detector is low and should be
replaced. This wireless smoke detector should be marked with a
number corresponding to the number of the lit zone light. The
replacement batteries required are Duracell 9 Volt Alkaline (2).
Warning: Replace batteries only with the same type as specified
above. Use of another bat tery may pres ent a risk of fire or ex plosion.
Do not recharge or disassemble battery, or dispose of i n fire.
A problem has been detected with a wireless smoke detector.
Call installing company for service.
13
Page 11
Programming User Codes
www.ealarm.com.my
Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but
also to enter the User Program Mode, where you can program other user codes. The following explains how
you will use this code to program or erase additional user codes.
Entering the User Program Mode
ARMED
READY
SYSTEM
FIRE
AC
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
Press
flash, and the keypad will beep 4 times. You are now in the User Program mode. Zone lights 1 through 6
will light to indicate any User Codes presently programmed.
Programming / Reprogramming User Codes
Press the User number to be programmed. (For example, press
1
The keypad will beep 2 times and the corresponding Zone light will flash to indicate the user
number you are about to program.
2
Press in the 4 digits of the new User 2 code, the keypad will beep 4 times.
3
If there are more user codes to be programmed, return to step 1 above, otherwise, go to Exiting the
User Program Mode below.
Erasing a User Code
1
Press the User number to be erased. The keypad will beep 2 times and the corresponding Zone light
will flash to indicate the user number you are about to erase.
2
Press
3
If there are more user codes to be erased, return to step 1 above, otherwise, go to Exiting the user
Program Mode below.
followed by
. The zone light will go out to indicate that the user code has been erased.
and then enter the User 1 code. The Armed, Status and 9System Lights will
to program the User 2 code.).
Exiting the User Program Mode
When you are done programming or erasing User codes, press " to Exit the User Program Mode.
14
Loading...