NAPCO QuickModem-W Installation Instruction

R

333 Bayview Avenue

Amityville, New York 11701

For Sales and Repairs, [phone]

For Technical Service, [phone]

© NAPCO 2004

INSTALLATION INSTRUCTIONS

Quick-Modem-W

GENERAL DESCRIPTION

The NAPCO Quick-Modem-W is a modem which is fully
compatible with the NAPCO PCD-Windows Quickloader
download software.

SPECIFICATIONS

Input Power: 9 VAC, 750-1000mA, 9.8 W (from supplied
AC adapter).

CONNECTION

Connect the Quick-Modem-W to the J2 connector of the
PCI2000 Interface module using a standard modem
cable (not supplied).

CONFIGURATION

The Quick-Modem-W must be configured as follows for
use with PCD-Windows:

Click File, Modem Settings to open the Serial Com-

munication Setup dialog (see image below).

NOTE: Although image below displays "Com 1" in the

Port fields, the Port number may be different in your sys­tem.

Select a Port to be used with the Quick-Modem-W. En­ter a Dial-out Prefix (if required) and the Telephone
Number. Select a PCI Port from the drop-down menu.
For Modem Type. select "StarComm 2400 Data (model
2400E-030).

WI1321 8/04

IMPORTANT NOTE

The enclosed modem supports:

• NAPCO's PCD-Windows Quickloader Download

software, Version 4.54 (enclosed) operating on MS
Windows 98/2000/XP

When operating under DOS, the "CallBack Download"
feature will not function. However, this feature is fully
supported on the NAPCO PCD-Windows Quickloader
Version 4.54 or greater. The problem observed is:

When using the enclosed modem with DOS PCD
2000/3000 only, an alarm panel callback connection can
not be established. DOS PCD 2000/3000 will call out
through the modem to initiate the callback, and the alarm
panel will call back. However, DOS PCD 2000/3000 will
not properly recognize the call back through the modem
and eventually time-out, indicating:

NOTE: If the feature "CallBack Download" is disabled in
the panel, a connection will be established immediately.

Due to the unavailability of industry support for DOS prod­ucts in general, providing future support of the "CallBack
Download" feature in PCD2000 is not planned. If DOS
support of the "CallBack Download" feature is required,
please contact NAPCO Customer Service at 1-800-645­9445 and inquire about the availability of legacy DOS mo­dems.

NOTE:

and

• DOS PCD 2000/3000, Versions 3.34B/2.34B oper-

ating on DOS 4.0 or higher.

Establish Connection Unsuccessful
Port/Cable/Modem/PCI Failure
:No RxData

If modem is to be used with PCD 2000/3000
(DOS application), refer to WI1066.

NAPCO Security Systems, Inc.

333 Bayview Avenue

#

Amityville, New York 11701

For Sales and Repairs, call Toll Free: [phone]

For Technical Assistance, Contact the NAPCO

Toll Free Helpline

[phone]

!

NAPCO LIMITED WARRANTY

NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants
its products to be free from manufacturing defects in
materials and workmanship for thirty-six months
following the date of manufacture. NAPCO will, within
said period, at its option, repair or replace any product
failing to operate correctly without charge to the original
purchaser or user.

This warranty shall not apply to any equipment, or any
part thereof, which has been repaired by others,
improperly installed, improperly used, abused, altered,
damaged, subjected to acts of God, or on which any
serial numbers have been altered, defaced or removed.
Seller will not be responsible for any dismantling or
reinstallation charges.

THERE ARE NO WARRANTIES, EXPRESS OR
IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. THERE IS
NO EXPRESS OR IMPLIED WARRANTY OF
MERCHANTABILITY OR A WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE. ADDITIONALLY,
THIS WARRANTY IS IN LIEU OF ALL OTHER
OBLIGATIONS OR LIABILITIES ON THE PART OF
NAPCO.

Any action for breach of warranty, including but not
limited to any implied warranty of merchantability, must
be brought within the six months following the end of the
warranty period.

IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE
FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY THE SELLER'S
OWN NEGLIGENCE OR FAULT.

In case of defect, contact the security professional who
installed and maintains your security system. In order to
exercise the warranty, the product must be returned by
the security professional, shipping costs prepaid and
insured to NAPCO. After repair or replacement, NAPCO
assumes the cost of returning products under warranty.
NAPCO shall have no obligation under this warranty, or
otherwise, if the product has been repaired by others,
improperly installed, improperly used, abused, altered,
damaged, subjected to accident, nuisance, flood, fire or
acts of God, or on which any serial numbers have been
altered, defaced or removed. NAPCO will not be
responsible for any dismantling, reassembly or
reinstallation charges.

This warranty contains the entire warranty. It is the sole
warranty and any prior agreements or representations,
whether oral or written, are either merged herein or are
expressly cancelled. NAPCO neither assumes, nor

authorizes any other person purporting to act on its
behalf to modify, to change, or to assume for it, any
other warranty or liability concerning its products.

In no event shall NAPCO be liable for an amount in
excess of NAPCO's original selling price of the product,
for any loss or damage, whether direct, indirect,
incidental, consequential, or otherwise arising out of any
failure of the product. Seller's warranty, as hereinabove
set forth, shall not be enlarged, diminished or affected by
and no obligation or liability shall arise or grow out of
Seller's rendering of technical advice or service in
connection with Buyer's order of the goods furnished
hereunder.

NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM
BE COMPLETELY TESTED WEEKLY.

Warning:

limited to, any or all of the following; criminal tampering,
electrical or communications disruption, it is possible for
the system to fail to perform as expected. NAPCO does
not represent that the product/system may not be
compromised or circumvented; or that the product or
system will prevent any personal injury or property loss
by burglary, robbery, fire or otherwise; nor that the
product or system will in all cases provide adequate
warning or protection. A properly installed and
maintained alarm may only reduce risk of burglary,
robbery, fire or otherwise but it is not insurance or a
guarantee that these events will not occur.
CONSEQUENTLY, SELLER SHALL HAVE NO
LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE
PRODUCT FAILED TO GIVE WARNING. Therefore, the
installer should in turn advise the consumer to take any
and all precautions for his or her safety including, but not
limited to, fleeing the premises and calling police or fire
department, in order to mitigate the possibilities of harm
and/or damage.

NAPCO is not an insurer of either the property or safety
of the user's family or employees, and limits its liability
for any loss or damage including incidental or
consequential damages to NAPCO's original selling
price of the product regardless of the cause of such loss
or damage.

Some states do not allow limitations on how long an
implied warranty lasts or do not allow the exclusion or
limitation of incidental or consequential damages, or
differentiate in their treatment of limitations of liability for
ordinary or gross negligence, so the above limitations or
exclusions may not apply to you. This Warranty gives
you specific legal rights and you may also have other
rights which vary from state to state.

Despite frequent testing, and due to, but not