NAPCO ISEE-QC2CAMKIT, ISEE-QC1CAM Installation Instructions Manual

R

333 Bayview Avenue

Amityville, New York 11701

For Sales and Repairs, [phone]

For Technical Service, [phone]

Publicly traded on NASDAQ Symbol: NSSC

© NAPCO 2008

ISEE-QC2CAMKIT Two-Camera Kit

ISEE-QC1CAM Single Camera Kit

Installation Instructions

WI1679 2/08

OVERVIEW

The NAPCO ISEE-QC2CAMKIT is a quick-connect installa­tion system that allows a simplified, standardized camera
installation using CAT5 cable and is intended for use with
the NAPCO VIP-Gateway. This installation kit includes two
(2) high quality IR cameras, passive video baluns with
power leads, and a rugged PVC camera mounting / wiring
enclosure system. This kit also includes a power distribu­tion system that can provide power to a maximum of four (4)
cameras from one economical plug-in 12VDC, 2 Amp
power supply. These instructions also apply to the ISEE­QC1CAM for individual cameras to be added to an existing
installation.

SYSTEM COMPONENTS

ISEE-CAMIR24 IR Bullet style camera,

24 IR LEDs, 50' IR range, 1/4"
Color CCD image sensor, 3.6mm /
f2.0 Standard Lens, 12VDC Op­eration.

ISEE-VBALUN-P1 Passive Video Balun

allows video and power transmis­sion over CAT5 cable, 6 push pin
terminals. Set of (1) male and (1)
female with 2.1mm CCTV power
lead connectors

ISEE-BNC P-CBL Patch Cable, BNC Male to Female,

RG59, 120mm (for connecting
ISEE-VBALUN-P1 Video Balun
to VIP-Gateway)

ISEE -TRF12VDC2A Plug in style

power transformer/adapter,
provides regulated 12VDC @
2,000mA output with 2.1mm
male connector.

ISEE-PWR1-4 Power Splitter,

CCTV, 1 Female to 4 Male

2.1mm. Provides power to up to
(4) cameras when using ISEE ­TRF12VDC2A power supply

(Base)

PVC double gang style weatherproof enclo-

sure, white, provides a watertight enclo­sure for wiring and allows the camera
to be easily and quickly mounted out­doors.

PVC double gang weatherproof cover with

gasket, prepped for mounting of camera
base, white.

PVC plug for sealing of wire entry hole, white,

is slotted to allow the camera cable to
exit the enclosure.

INSTALLATION

The PVC camera mounting / wiring enclosure system al­lows the camera to be easily and quickly installed on the
side of a building or under an eave. Before wiring the en-
closure, attach the camera mounting bracket base to the
enclosure cover using the three supplied mounting nuts and
bolts.

1. Pull the CAT5 wire through the wall or eave to the loca­tion where the camera is to be installed. Punch through
the knock-out on the bottom of the enclosure and one
1/2 inch threaded knock-out on the side. Push the
camera signal and power connectors (one at a time)
through the 1/2 inch threaded hole on the side of the
enclosure.

Knockout

for CAT5

cable

Threaded
hole plug

Note: The product images shown in this manual may be slightly different from the actual product.

Fig. 1: Route the camera wires into enclosure

1

2. Pull an appropriate length of camera cable through the

side entry hole and secure the opening with the PVC
mounting plug. Place the notch on the plug over the
cable and screw into place.

Fig. 2: Install wire plug into enclosure

3. Pull the CAT5 cable through the wire entry hole on the
bottom of the enclosure.

CAT 5 Cable

Fig. 3: Route CAT 5 Cable into base

4. Connect the camera power lead to the video balun with

the male power jack and attach the camera signal lead
to the video balun.

Fig. 4: Secure cover to enclosure

5. Connect the ISEE-VBALUN-P1 Video Balun to CAT5.

Select one pair of CAT5 conductors to be used for
video signal and the remaining 2 or 3 pair to be used to
provide power to the camera. Refer to the following
table to determine the number of CAT5 power conduc­tors required, which is dependent on the length of the
CAT5 cable run.

Length of Wire Run No. of CAT5 Pair Required

125 Feet 3 Pair

100 Feet 3 Pair

75 Feet 2 Pair

50 Feet 2 Pair

6. Connect the CAT5 cable to the ISEE-VBALUN-P1
Video Balun by pushing in the pin-push terminals and
sliding the stripped conductors into the terminal open­ing.

Fig. 5: Connect CAT5 conductors to video balun

7. After all connections are secure, tie up excess wires

and place wire and balun inside enclosure as shown in
Fig. 6.

Note: To ensure high-quality electrical connections in

outdoor installations, a packet of dielectric grease is
included in the kit. Place a small amount on the BNC
center conductor as well as each stripped CAT5 con­ductor before making the connections to the balun.

Fig. 6: Place cable and balun into enclosure

8. Affix gasket to cover and secure cover to enclosure with
four (4) screws (supplied) as shown in Fig. 7.

Fig. 7: Secure cover to enclosure

9. The camera enclosure can be mounted on a wall (see

Fig. 8) or a ceiling (see Fig. 9). If mounting on a wall,

2