NAPCO IQProfiler Installation Instruction

Advanced Profiling Technology

PASSIVE INFRARED SENSOR

INSTALLATION INSTRUCTIONS

Napco Security Systems, Inc.

333 Bayview Avenue, Amityville, New York 11701

For Sales and Repairs, [phone]

R

WI1017 08/00

TM

1

Now it just takes a minute and a screwdriver to install
the smart microprocessor-based PIR that profiles
targets against a built-in library of 1200+ false alarm
and alarm sources for verified detection -- NAPCO’s IQ
Profiler Sensor!

• 50 lb. Pet Immunity (22.7kg) *

• Maximum Range: 50 x 50 Feet (15.2m x 15.2m)

• Superior False Alarm Discrimination and Unique Dual

Focal Lenses in Advanced Bi-Optic Contour Case.

• IQ Profiling: Each detected signal is profiled against

Napco’s proprietary built-in library of false alarm
signals and real alarm signals for maximum
accuracy.

• Shielded High-Performance Aspheric Lenses plus

Look-Down/Creep Zone

• Sensor Chamber prevents insect, draft, and dust

interference.

• Quick Mount: A quarter-turn of a screwdriver in the

back housing’s mounting disk and the unit embeds
itself in any corner in seconds, with innovative self­projecting, fast anchoring wall pins.

• Quick Wire: “Snap-Down” Terminal Strips hold

wires fast (No screws!) Just insert stripped wires in
each and snap down (speaker-jack style).

• Wall & Swivel Mounting (SVL2), too.

* Pet Immunity has not been evaluated by UL.

2

SPECIFICATIONS

Coverage (l x w): 50' x 50' (15.2m x 15.2m) at 20°C (68°F),

typical. (with High Sensitivity Jumper “SEN”
installed)
30' x 35' (9.1m x 10.6m) at 20°C (68°F),
typical. (with Normal Sensitivity)

Operating Temperature: -10° to +50°C (14°F to 122°F)
Mounting: Wall or corner, 6.5’ to 8.5' max.
Alarm Output: Normally-Closed Form-A Relay
Contact Ratings: 100mA, 24VDC with internal 10 Ohm current-

limiting resistor

POWER-SUPPLY REQUIREMENTS

Note: This unit is intended for operation from a power source that

provides a 4 hour battery backup in the event of a power failure.
Filtered Dc: 10.6 to 16V DC nominal with battery backup from

control panel.
Current Drain: 28mA (idle or alarm) at 12VDC (nominal) 33mA

(idle or alarm) at 16VDC (nominal).

PHYSICAL

Dimensions: 4.5 in x 2.5 in x 1.8 in (HxWxD)
Shipping Weight: 6 oz.

3

• Bi-Optic Contour Case and Dual focal lenses

provide exceptional distance profiling:

• “Far Field Lens” allows for detection of large

objects and ignores small targets nearby

• “Near Field Lens” allows for discrimination of

small targets nearby

 NAPCO 10/00 Pats. Pending

IQ Profiler is a trademanrk of NAPCO

4

Locating the Detector

Corner mounting is preferred as it provides the best overall
coverage. Choose a corner where the path of an intruder will most
likely cross beams, as opposed to walking towards or away from
them. This lens is intentionally made with an 85 degree angle of
view, to help prevent curtains on windows from being in detection
zones.
Sources of heat, such as radiators and space heaters, do not
usually pose a problem as long as hot air from them does not
blow directly onto the detector. One exception to this is overhead
radiant heaters, these produce very high levels of infrared energy
and can heat the unit at some distance. Mount the unit as far from
these as possible. Do not mount the unit where the sun can shine
directly on it. Mount it away from the direction of sunlight.

Standard Installation

Protection pattern

85°

7’

50’

Top View

Side View

50’

5