USING YOUR 2WAY-UNIVKF KEYFOB
Controls
The KeyFob’s 4 command buttons provide complete system control. Commands are issued to the
alarm system by either pressing or holding down (for 2 seconds) the appropriate button.
The KeyFob antenna
may be extended for
increased operating
STATUS
Press STATUS to
update the display
with the current
system status.
The proper icon(s)
will appear, accompanied by the appropriate beep(s). (see
Audible Indicators)
The icon(s) will
automatically go out
in about 6 seconds.
ON/OFF
Press ON/OFF to arm or
disarm the alarm system.
Hold Down ON/OFF to Arm
the system in STAY mode.
ON/OFF
Press ON/OFF and ∗∗ simultaneously for:
AND
Hold Down PANIC
for 2 seconds to
activate a panic
alarm.
∗
∗
Press ∗∗ for:
PANIC
Hold Down ∗∗ for 2
seconds for:
∗
∗
Audible Indicators
For each command
issued, the KeyFob will
give feedback beep(s) to
confirm that it has been
acknowledged by the
system.
# of
Beeps State
1 Armed
2 Disarmed
3 Armed,
Stay mode
4 Armed, zones
bypassed
5 System Trouble
6...
(repeats)
Alarm !
Visual LCD Indicators
The 2WAY-UNIVKF uses a series of icons to convey the status of the † system. Each time the STATUS button is pressed, or
any command is issued, the appropriate icon(s) will display for about 6 seconds. For example, if ON/OFF is pressed to arm
the system, the Armed Icon will light in a few seconds to confirm that the command was successfully carried out. Below is a
description of each icon indicator. Please note that the icons marked “†” are optional and may not apply to all systems.
Armed
The system is armed.
Armed Bypassed †
(slowly flashing) The system is
armed with zones bypassed.
Transmit Each time a button is
pressed the transmit ICON will light to
indicate that the KeyFob is
transmitting to the receiver.
Stay Mode † The system
is armed with interior zones
bypassed.
System in Alarm / Alarm Memory
(flashing) The system alarm is sounding
or an alarm has occurred while you were
System Ready The system is
disarmed, with all zones secure.
The system is ready to arm.
Zones Faulted † (slowly flashing)
Disarmed, zones faulted.
Fire Alarm † (flashing) The
system is in a fire alarm condition
System Trouble † The alarm system is in a
trouble condition. Consult keypad and owners
manual for the exact nature of the trouble.
Enrolling and Removing KeyFobs
Each KeyFob used in the system must be enrolled into the receiver
using the following procedure:
Use a pen or pencil to depress and hold the recessed
1
Enroll Mode Push Button on the top of the receiver.
Release when the Enroll Mode LED begins to flash.
!
Enroll Mode
Push Button
Receiver
Entered Enroll Mode - The Enroll Mode LED will
continue to flash.
Enroll Mode
LED
2 Press the ∗∗ button on KeyFob 1.
3 Press the ∗∗ button on KeyFob 2 (if more than one).
Repeat for each KeyFob to be programmed into system.
...
Press Enroll Mode Push Button or ON/OFF on KeyFob. Exit Enroll Mode - the Enroll Mode LED will go out.
•
To remove a lost KeyFob from the system: Enter and then exit the Keyfob Enroll Mode. (Hold down Enroll Mode Push Button
until Enroll Mode LED flashes, release and then hold down again to exit Enroll Mode). All keyfobs will be deleted from system.
Changing the KeyFob battery
1 Open battery compartment on back of Keyfob.
2 Remove old battery and replace with new.
The KeyFob will sound a confirmation beep.
The KeyFob will sound a confirmation beep.
3 Replace battery
compartment cover
G
+
Note: There is no need to re-enroll the KeyFob after a battery change.
AAA
Use only AAA 1.5 Volt alkaline battery.
NAPCO LIMITED WARRANTY
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from
manufacturing defects in materials and workmanship for thirty-six months following the date
of manufacture. NAPCO will, within said period, at its option, repair or replace any product
failing to operate correctly without charge to the original purchaser or user.
This warranty shall not apply to any equipment, or any part thereof, which has been repaired
by others, improperly installed, improperly used, abused, altered, damaged, subjected to
acts of God, or on which any serial numbers have been altered, defaced or removed. Seller
will not be responsible for any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED
WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER
OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO.
Any action for breach of warranty, including but not limited to any implied warranty of
merchantability, must be brought within the six months following the end of the warranty
period.
IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S
OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who installed and maintains your security
system. In order to exercise the warranty, the product must be returned by the security
professional, shipping costs prepaid and insured to NAPCO. After repair or replacement,
NAPCO assumes the cost of returning products under warranty. NAPCO shall have no
obligation under this warranty, or otherwise, if the product has been repaired by others,
improperly installed, improperly used, abused, altered, damaged, subjected to accident,
nuisance, flood, fire or acts of God, or on which any serial numbers have been altered,
defaced or removed. NAPCO will not be responsible for any dismantling, reassembly or
reinstallation charges.
This warranty contains the entire warranty. It is the sole warranty and any prior agreements
or representations, whether oral or written, are either merged herein or are expressly
canceled. NAPCO neither assumes, nor authorizes any other person purporting to act on its
behalf to modify, to change, or to assume for it, any other warranty or liability concerning its
products.
In no event shall NAPCO be liable for an amount in excess of NAPCO's original selling price
of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or
NAPCO Security Systems, 333 Bayview Avenue, Amityville, NY 11701
otherwise arising out of any failure of the product. Seller's warranty, as hereinabove set forth,
shall not be enlarged, diminished or affected by and no obligation or liability shall arise or
grow out of Seller's rendering of technical advice or service in connection with Buyer's order
of the goods furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED
WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following;
criminal tampering, electrical or communications disruption, it is possible for the system to
fail to perform as expected. NAPCO does not represent that the product/system may not be
compromised or circumvented; or that the product or system will prevent any personal injury
or property loss by burglary, robbery, fire or otherwise; nor that the product or system will in
all cases provide adequate warning or protection. A properly installed and maintained alarm
may only reduce risk of burglary, robbery, fire or otherwise but it is not insurance or a
guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO
LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS
BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer
should in turn advise the consumer to take any and all precautions for his or her safety
including, but not limited to, fleeing the premises and calling police or fire department, in order
to mitigate the possibilities of harm and/or damage.
NAPCO is not an insurer of either the property or safety of the user's family or employees,
and limits its liability for any loss or damage including incidental or consequential damages to
NAPCO's original selling price of the product regardless of the cause of such loss or
damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the
exclusion or limitation of incidental or consequential damages, or differentiate in their
treatment of limitations of liability for ordinary or gross negligence, so the above limitations or
exclusions may not apply to you. This Warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
FCC ID: AD82WAYUNIVKF
This device complies with part 15 of the FCC Rules. Operation is subject
to the following:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
OI268A 01/01
Loading...