Nanosat Nano Premium SE User Manual

Download

User's Manual

Table of Contents

Safety Warning

General Information

Package Contents & Features

Front Panel

Rear Panel

Remote Control Unit (RCU)

Programing the Remote Control

Installing Equipment

Channel List Guide

Menu Guide

Main Page

I. CHANNEL MANAGER

II. INSTALLATION

III. OPTIONS

IV. UTILITY

Troubleshooting

Specifications

Brand List

TABLE OF CONTENTS

Table of Contents

User’s

Manual

User’s

Manual

Please ensure that the following items are included with the receiver in your packing.

Remote Control

Unit

User's Manual

Batteries 2EA

(for RCU)

User's Manual

GENERAL INFORMATION

Package Contents & Features

User's Manual

ser’s

anual

A V

/ T V

Package Contents

SAFETY WARNING

Warning

Please read the following recommended instructions carefully to avoid the risk of your physical Injury before the product is operated.

Safety Instructions and Precautions

- Do not cover the receiver and keep clear space around the receiver for sufficient air circulation.

- Check the receiver's operation voltage 90~250V, 50Hz~60Hz, Max 30W Keep liquid away from the

receiver.

- The receiver shall not be exposed to dripping or splashing and no objects that filled with liquid shall not be placed on the receiver.

- Unplug the receiver from the wall outlet before cleaning.

- Use a soft cloth and a mild solution of washing-up liquid to clean the casing.

- Do not block the receiver's ventilation slots which are provided for ventilation and protection from overheating.

- Please maintain the receiver in a free airflow.

- Do not allow the receiver to be exposed to hot, cold or humid condition.

- Do not use any cable and attachment that are not recommended as these may damage your equip

ment.

- Please unplug the receiver from the wall outlet and disconnect the cable between the receiver and the antenna when you will not use it for long time.

- Do not remove the cover to reduce the risk of electric shock.

- Do not attempt to service the receiver yourself.

- Refer all serving to qualified service personnel.

- The manual's contents may be updated without notice.

NOTE: To disconnect the apparatus from the mains, the plug must be pulled out from the mains sock-

et, therefore the mains plug shall be readily operable.

Features

User’s

Manual

RCA Cable

• Home streaming

• Live IP Movie/Radio

• 3 x USB 2.0 Hosts (Access to HDD, USB memory, Others etc)

• Wi-Fi

• Universal Remote

• Built-In Ethernet Port

• MP3 File Play by USB 2.0

• PVR Ready via USB

• Recorded file play on PC

• Reservation Recoding by EPG function

• MPEG-II Digital & Fully DVB Compliant.

• C/KU band control for each antenna

• LNB Tone Switch 22KHz mode on/off

• Multi-LNB controlled by DiSeqC =>DiSEqC 1.0, 1.1, 1.2 and USALS

• Total 8,000 Channels Programmable

• Blind Scan

• Picture In Graphic (PIG)

• Electronic Program Guide (EPG) for On Screen Channel Information

• Multi-language supported for Menu and OSD

• Zoom Function by 2x...4x

• Parental Lock

• Closed Caption Support

• CVBS Video & Audio Output via RCA

• Component YUV Output via RCA

• 7-Segment (4-digit) Type of Front Panel Display

• Upgrade Software & Update Channel Database through USB 2.0 Port

• Dolby Digital

• HDMI (HD quality picture)

User's Manual

GENERAL INFORMATION

User's Manual

GENERAL INFORMATION

1 4

1. CH Up/Down

Channel up / down or select the item of Menu.

2. VOL Left/Right

Volume left/right or select the item of Menu.

3. POWER Button

Switch between Power on and Standby mode.

4. USB Port

To upgrade firmware / Recording.

NOTE: The front panel of the product is subject to change without notice.

Front Panel

Rear Panel

6 7

1. SAT IN

Connect to Satellite antenna cable.

2. LOOP OUT

Connect to another STB.

3. Component (YPbPr)

Connect to Component jack of TV.

4. VIDEO

Connect VIDEO to the TV or other equipment.

5. TV / VCR

Connect to TV or VCR.

6. ANT

Connect to TV antenna input.

7. S-VHS

Connect to the S-VHS jack of TV.

8. HDMI

Connect to the TV usinmg an HDMI cable.

9. RS 232

Connect to personal computer for software upgrade.

10. ETHERNET

Connect to Lan cable. (RJ-45)

11. USB PORT

To Upgrade Firmware / Recording / Wifi connection.

12. USB PORT (Wi-Fi Only)

This is to be used for Nanosat Wifi Adapter only.

13. POWER SUPPLY

90~250V AC, 50/60Hz, 30W.

14. POWER BUTTON

Turn On/Off.

NOTE: The rear panel of the product is subject to change without notice.

GENERAL INFORMATION

Remote Control Unit (RCU)

1 2

3 4

5 6

10 11

23 24

25 26

12 13

User's Manual

GENERAL INFORMATION

Remote Control Unit (RCU)

User's Manual

21. PAL / NTSC

Switch PAL or NTSC mode.

22. INFO

Display the program information box on the screen and edit the name of favorite channel list.

23. AUDIO

Change the audio languages.

24.

Select the sound mode(LEFT/RIGHT/STEREO).

25. EPG (Electronic Program Guide)

Display the TV or Radio program guide.

26.

Enable subtitle and teletext mode.

27. V+ / V-

Turn volume up or down.

28. P+ / P-

Change channels up or down on normal mode.

29. MUTE

Enable or disable the audio.

30. RF CH

Select the RF channel.

31. Fn

Theme / Network File Manager/ Reboot.

32. V.Format

Switch to HD Type.

33.



Select the previously viewed channel.

34. REWIND

Start reverse playback and change the speed of reverse playback.

35. F / F

Start fast forward or fast motion playback and change the speed of forward playback.

36. PLAY

Display file lists and plays slow/normal.

37. STOP

Stop recording or playing.

38. PAUSE

Pause the playing picture or go to normal mode.

39. RECORD

Record the program.

1. POWER

Switch the receiver between operation and standby mode.

2. TV POWER

Turn on/off the TV.

4. STB

Switch to STB mode.

4. TV

Switch to TV mode.

5. VCR

Switch to VCR mode.

6. DVD

Switch to DVD mode.

7. Numeric buttons

Select the TV or Radio service channels and individual menu.

8. TV / RADIO

Switch between TV and Radio.

9. AV / TV

Select the TV or AV mode.

10. RECALL

Select the previously viewed channel.

11. INPUT

Select the TV external input.

12.

Sleep Timer / Move down a page in the channel list.

13.

Move up a page in the channel list.

14. MENU

Display the main menu on screen.

15. EXIT

Return to the previous menu or normal viewing mode from a menu.

16.





Change channel or move to the item in the menu.

17.





Adjust the volume or move to left or move item in the menu.

18. OK

OK button.

19. FAV

Toggle the selected favorite mode.

20. SAT

Toggle the selected Satellite list.

There are two ways to program the remote control - Automatic Code Search or Direct Entry.

I. Using Automatic Code Search

1) Turn on the component you want to control (TV, VCR or DVD).

2) Press and hold the component key you want to program. Holding the component key until the LED on the

remote control turns on, then release the key.- ➊

3) Point the remote at the component, press and release the ➌UP (



) button, then wait three seconds or

until the LED stops flashing.

At this point the remote control is searching for the correct code to program. If, after three seconds, the component you want to control does not turn off, press and release ➌UP (



) button again to tell the

remote to search the next set of codes.

4) If the component you want to control does turn off; Press and release ➍OK Button , then the LED blinks

three times.

II. Using Direct Entry Method

1) Turn on the component you want to control (TV, VCR or DVD).

2) Locate the enclosed Code List. Find your brand of the component you want to control.

3) Press and hold the component key you want to program. Holding the component key until the LED on the remote control turns on, then release the key.

4) Enter 3-digit code from the code list, then the LED blinks three times.

5) If you get no response, repeat these steps using the next code listed for your brand until the component responds to the remote control command.

III. Changing Volume Lock

Locking the volume controls to a single device makes it easier to control volume, without having to guess whether the volume will change. If you lock the remote's volume controls to the TV , you will always be able to change the volume to the level you want, without having to adjust it on multiple devices.

If you want to lock the volume for the STB component ;

1) Press and hold the STB component key until the LED on the remote control turns on.

2) Enter 3-digit code, 9 9 9 .

3) Press and release the STB component key, then the LED blinks three times.

Unlocking volume control ; If you want to unlock the volume for the STB component ;

1) Press and hold the STB component key until the LED on the remote control turns on.

2) Enter 3-digit code, 9 9 9 .

3) Press and release the STB component key, then the LED blinks three times.

GENERAL INFORMATION

Programing the Remote Control

User's Manual

GENERAL INFORMATION

Programing the Remote Control

Programing the RCU

User's Manual

INSTALLING EQUIPMENTS

Connections

User's Manual

CHANNEL LIST GUIDE

Channel List Guide

1. Normal Live Mode

a) When you select one channel, information bar appears

automatically on the screen for few seconds. This bar provides you the current channel information.

b) Press INFO button to see the information during normal

live mode.

2. Simple Channel List

a) Press OK on the normal live mode to go to the channel

list.

b) When detail channel list is displayed on screen press

RED button to go to simple channel list..

3. Detail Channel List

a) Press OK on the normal live mode to go to the channel

list.

b) When simple channel list is displayed on screen press

[RED] key to go to detail channel list.

c) Press

◀▶

and ▲▼to sort by Alphabet.

d) Press SAT button to sort by Satellite and FAV button for

Favorite 1~8.

e) Press GREEN button to return to All Channel or EXIT to

return to the current live channel.

f) Press the SAT key to show Satellite Pop-UP Window then

select satellite. Channel list of selected satellite will be displayed.

g) Press the FAV key to show Favorite Pop-UP Window then

select FAV list. Channel list of selected FAV will be displayed.

h) Press the Green key then all searched channel list will be

displayed.

i) Press MENU key then cursor will move to ALL, placed on

the left.

j) Sort Key (Yellow Key)~A~Z/Z~A/FAT/CAS.

k) Press Yellow key for sorting A~Z/Z~A/FAT/CAS. If you

want to go back to unsort from the selected CAS go back to Pop-UP Window then select unsort.

CHANNEL LIST GUIDE

This section explains several ways of connecting the receiver to your existing TV, VCR and Hi-Fi system. You can choose one of the following setups that we recommend. If you have any problem or need help, consult your dealer or service provider. Please ensure that the following items are included with the receiver in your packaging.

Connecting the receiver to TV and VCR with RF cable

Connect one end of the RF cable TV/VCR socket on the rear panel of the receiver and the other end to the ANT IN on the TV. Connect one end of the RF cable to the ANT socket on the rear panel of the receiver and the other end to the ANT OUT on the VCR.

Connect one end of HDMI cable to the HDMI output of your receiver and another end of cable to HDMI IN connector on your TV.

Connecting the receiver to TV with HDMI cable

4. EPG (Electronic Program Guide)

a) Press EPG button on the live mode.

b) EPG of the current channel appears on the screen.

c) Select the channel that you want to watch program.

d) Red Circle will appear like the right side picture.

e) To activate event timer, press REC button twice.

f) Green Circle will appear.

g) If you like to cancel reserved program, press REC button

until Red or Green Circle disappears.

h) Press OK button twice to return to current live channel.

i) Also, you can find the EPG information using FN button.

FN button: Search by Title, Summary or Both. This is the fastest way to search for a particular channel you want to watch.

5. ZOOM IN/OUT

a) By selecting page up key ( ) in a normal live mode you

can use Zoom In/Out function.

b) From the Pop-Up Window of Zoom function you can

select(*2*3*4)by page up key( ), for Zoom out press page down key.

c) When you move cursor of Zoom focus by key (▲▼◀ ▶)

then you can select Zoom In/Out on the focused point by pressing page up/down keys. Press Pause key then live mode will be paused on the mode of Zoom.

Press the [MENU] key on the RCU to open Main Page on the screen. Main Page will be displayed.

1. You can move into the main page using ▲▼◀ ▶ on the RCU.

2. Press [OK] to confirm your selection.

3. Press [EXIT] to return to the previous menu or press [MENU] to go to the current live channel.

This chapter explains how to organize channels according to your preference.

1. Select Channel Manager in the Main Page with ▲▼ and press OK.

2. TV Channel Manager Page displays on the screen.

3. Select the mode that you want to use◀ ▶.

4. To see the channel that you choose, go to the channel and then press RED button.

5. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

I-1. Favorite

User's Manual

MENU GUIDE

I. Channel Manager

MAIN PAGE

I. CHANNEL MANAGER

I-1. Favorite I-2. Rename I-3. Move I-4. Lock I-5. Delete

1. Using ◀▶go to the Favorite mode then press YELLOW button to choose Favorite 1~8.

. Press OK on the channel that you want to add or delete.

3. will be marked at the end of selected channel name bar. To delete press OK again.

4. Selected channels will be automatically saved.

5. If you want to check the saved Favorite Channel List go to other mode (Rename~Delete) except Favorite and then press FAV button to check Favorite 1~8.

6. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

User's Manual

CHANNEL LIST GUIDE

Channel List Guide

User's Manual

MENU GUIDE

II. Installation

II. INSTALLATION

User's Manual

MENU GUIDE

I. Channel Manager

I-2. Rename

1. Using◀▶go to the Rename mode.

2. Select the channel that you want to rename using ▲▼ and then press OK.

3. Keypad Dialog displays on the screen.

. Edit the name entering NUMBERS and / or WORDS in the

Keypad Dialog.

5. Press YELLOW button to rename Favorite 1~8 and press BLUE button to rename Satellite.

6. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

I-3. Move

1. Using◀▶go to the Move mode.

2. Select channels which you want to move by pressing OK key.

3. Move cursor that you want to place on than press GREEN button.

4. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

I-4. Lock

1. Using◀▶go to the Lock mode.

2. Select the channel that you want to lock and then press OK. will be marked at the end of the selected channel name bar. To delete press OK again.

3. Press EXIT to go to Main Page or press MENU to go to the current live channel.

I-5. Delete

1. Using◀ ▶go to the Delete mode.

2. Select the channel that you want to delete and then press OK.

will be marked on the selected channel

number. To delete press Blue button again.

3. Press YELLOW button to delete TP. Select one channel and press Blue button. All channels of that TP will be automatically selected.

4. Press YELLOW button to delete Satellite. Select one channel and press Blue button. All channels of that the Satellite will be automatically selected.

5. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

6. Message Box displays on the screen.

7. Select OK on the Message Box and then press OK to delete the marked channels.

This section may help you to set up antenna and scan satellite or transponder, etc. Select Installations in Main Page using ▲▼ and press OK.

Press EXIT to return to the previous menu or press MENU to go to the current live channel.

II-1 Channel Search II-2. DiSEqC Switch II-3. Motor Setup II-4. Network

II-1 Channel Search

1. You can move the cursor using ▲▼ and press OK

when you select the value that you want.

a) Satellite

- Press OK to display the Satellite List Box.

- Select the proper Satellite and then press OK. b) DiSEqC

- Press OK to display the DiSEqC Port List.

- Select the proper DiSEqC port and then press OK. c) Frequency

- Press OK to display the Frequency List.

- Select the proper Frequency and then press OK. d) LNB

- Press OK to display the LNB Frequency List.

- Select the proper LNB Frequency and then press OK.

You can also input directly the numbers using NUMBER KEY on the RCU.

e) 22KHz Tone

- Select the one among None, 0 KHz or 22 KHz depending on the user’s antenna switch box.

f) Search Option

- Press OK to display the Search Option list.

- Select the Search Option that you want and then press OK.

g) Search

- Press Search to start scan channels.

- Selected Satellite displays on the screen.

- Press ▶ to select more Satellite or ◀ to cancel the selected Satellites.

- Press OK to start scanning.

User's Manual

II-2. DiSEqC Switch

1. Select Channel Search in Installation using ▲▼

and press OK.

a) If you select DiSEqC Switch and press OK on the menu,

DiSEqC Switch Page will be displayed.

b) Select the proper Satellite of each DiSEqC port using

◀▶and ▲▼ and press SEARCH. Selected Satellites will be searched automatically.

II-3 Motor Setup

1. You can move the cursor using ▲▼ and press OK when you select the value that you want.

a) Motor Type : DiSEqC 1.2, USAL

- Press OK to display Motor Type

- Select the proper Motor Type and then press OK.

b) Satellite

- Press OK to Display the Satellite List Box

- Select the proper Satellite and then press OK.

c) Switch & LNB

- Press OK to Display the LNB frequency list or Switch

Setting

- Select proper LNB & proper Switch.

d) Frequency

- Press OK to Display the Frequency List.

- Select the proper Frequency and then press OK.

e) Motor Movement

- Search the appropriate position of the selected Satellite

using ◀▶.

User's Manual

MENU GUIDE

II. Installation

II-3 Motor Setup

f) Motor Control

Select the position using ◀▶and then press OK. Message box displays on the screen.

- Store Sat position :

Stores the current position of the motor for the selected satellite.

- Goto Sat Position : Moves the motor to the stored position of the selected satellite.

- Goto 0 : Goes to the center of the motor.

- Reset Position : Resets all stored position of the motor.

MENU GUIDE

II. Installation

g) Satellite Position

- Input directly the position using NUMBER KEY on the RCU

- Select the direction using ◀▶(WEST / EAST).

h) Search Option

- Press OK to display the Search Option list.

Select the Search Option that you want and then press OK.

i) Search

- Press Search to start scan channels.

- Press OK to start scanning.

2. Edit my local position

- Press Green Button to edit local Position. a) Longtitude

- Input directly the Longtitude using NUMBER KEY on the RCU.

- Select the direction using ◀▶(WEST / EAST). b) Latitude

- Input directly the Latitude using NUMBER KEY on the RCU.

- Select the direction using ▲▼ (NORTH / SOUTH).

3. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

◈TP EDIT

To Edit TP Press the RED button on the RCU.

User's Manual

MENU GUIDE

II. Installation

User's Manual

MENU GUIDE

II. Installation

II-4. Network

This section may help you to set up network configurartion.

1. IP Setup Select one from three kinds of options for

Network Setting. Network connection status will be displayed on the bottom of screen.

a) Not Used

- In this case, network is disabled.

b) Automatic

- This is for user to use Dynamic (DHCP) IP address serv-

ice. After Select Automatic, push Apply button, STB will get a new IP from router automatically.

c) Manual

- This is for user to use static IP address service Put in

with your IP address, Subnet mask and Gateway. And push Apply button, then Box will reboot by itself.

2. Home Streaming

Home Streaming feature enables to watch downloaded MPEG movie files with your TV directly. First, please set up the Home Streaming program in your computer, and then configure your unit according to your router information to connect with computer.

There are 3 tabs in Home Streaming Program.

1st Tab (Movies) : It shows file list in PC server

2nd Tab (Download) : Reserved for future function

3rd Tab (Preference) : Configuration

1) Setting in your PC

a) Please go to “Preference” Tab

) Select “Use default” check-box and assign the

download folder by using “Browse”

It is assigned to “c:\download” but you should specify the destination folder personally.

II-4. Network

2) Configuration in your STB

a) Please go to IP Set up and click “Apply”

(Installations  Network  IP Set up)

) Exit from IP set up and go to Home Stream Setup.

User must insert Server-IP into the STB by using numeric buttons personally.

c) The IP address must be the same as showed in pref-

erence of “Home Streaming program”.

d) You can access "Home Streaming" function by press-

ing "Network File Manager" button.

3) Playing the Movie File

a) Please go to “Movies” Tab in Home Streaming

Program on your computer.

b) This tap shows the contents in the folder which you

specified.

c) If you do not see the contents, then press "Refresh"

button to reset "Movies" page.

d) Press "Fn" key on RCU in view mode and select

Network File Manager, now you should see the same Movie list on TV, just like the list on your "Shared Folder" on your computer screen.

e) Please select the file which you want to see by using

navigation keys of RCU and press “OK” to play the Movie file.

f) When playing selected files, your IP adress will appear

on "Connection" box in Home Streaming program.



Please see the right picture for better understanding.

◈Please note

● Support only Mpeg file currently.

● When appears "Network Error...8000" message,

please check IP setting in IP setup or Home Stream Setup Menu in your Set Top Box.

● Make sure your "Home Streaming Folder" that

you've created is SHARED with your Home net

work.

● Make sure you've converted your downloaded

movies to MPEG file.

III-2. Control Panel

1. Select TV Setup in Options using ▲▼ and press OK.

a) UHF Channel

- Press OK to display UHF Channel list.

- Select the proper channel and then press OK.

b) Closed Caption

- You can turn on/off the Closed Caption function.

c) USB Auto Detect

- You can turn on/off the USB Auto Detect function.

2. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

III-3. Time Adjust

Set your local time according to your location.

1. Select Time Setup in Options using◀ ▶ and press OK.

2. Time Adjust page displays on the screen.

3. Move the cursor using◀ ▶

,▲▼and press OK when you select the value that you want. (Input Hour directly using number keys on the RCU)

4. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

III-4. Parental Lock Setup

1. Select Parental Lock Setup in Options using◀ ▶ and press OK.

2. Parental Lock Page displays on the screen.

3. You can lock and unlock Parental Lock selecting ON or OFF using ▲▼ (For Channels).

. You can lock and unlock Install Lock selecting ON or OFF

using▲▼(For Installation Settings).

. Enter new password if you want to change the current

password.

6. Confirm your new password entering new password again.

7. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

User's Manual

MENU GUIDE

III. Options

his section may help you to set up OSD language, time, etc. Select Options in Main Page using ▲▼ and

press OK. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

III-1. OSD Setup III-2. Control Panel III-3. Time Adjust III-4. Parental Lock

III-1. OSD Setup

1. Select OSD Setup in Options using ▲▼ and press

OK.

a) OSD Language

- Press OK to display OSD Language list.

- Select the language that you want and then press OK.

b) Audio Language

- Press OK to display Audio Language list.

- Select the language that you want and then press OK.

c) Display Info Bar

- Press OK to display Display Info Bar time list.

- Select the second that you want to display and then press OK.

d) OSD Position

- Press OK to change Horizontal and Vertical Position of the OSD.

- OSD Position box displays on the screen.

- Select Hor Position / Ver Position using ▲▼.

- Move the OSD Position to right/left or up/down using◀▶.

- Select OK on the OSD Position box and then press OK.

e) Screen format

- Press OK to display screen format list.

- Select the format that you want and then press OK.

2. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

User's Manual

MENU GUIDE

III. Options

III. OPTIONS

User's Manual

TROUBLESHOOTING

Troubleshooting

This section may help you to use USB, etc. Select Utility in Main Page using

▲▼ and press OK.

IV-1. System Information IV-2. USB IV-3. Time Record IV-4. Factory Default

IV-1. System Information

This option help you to know the current S/W and H/W version. Also provides you the product name.

1. Select System Information in Options using ▲▼ and press OK.

2. Press EXIT to return to the previous menu.

IV-2 USB

The receiver is equipped with host.

1. Select USB in Utility with ▲▼ and press OK.

2. If you want to change mode (S/W Upgrade, BootLoader Upgrade), press RED button on the RCU.

3. Select the file which you want to upgrade using ▲▼ and press OK.

4. After downloading the selected file, the receiver will reboot automatically.

IV-3 Time Record

1. If you "ENABLE" option set to YES, you can edit TIME RECORD function.

IV-4 Factory Default

Use Factory Default function only when you want to return the receiver to the condition of factory default. All settings and channels will be deleted.

1. Select Factory Default in Installations using ▲▼ and press OK.

2. Message box displays on the screen.

3. Select OK to return the receiver to the condition of factory default and then press OK.

4. Press EXIT to return to the previous menu or press MENU to go to the current live channel.

MENU GUIDE

IV.Utility

IV. UTILITY

User's Manual

Before contacting your local service center, please read the tips below carefully. If the problem persists after completing the following procedure, please contact your local retrailer for further instructions.

1. Nothing appears on the Front Panel or No power supply

- Check that the power cable is plugged into the power socket.

2. No Picture

3. No Sound

4. Remote Control Unit does not work

5. "No Signal" on the screen

6. Tuner detective check

- Go to the Option and select System Information.

7. You have forgotten your secret PIN code

- You have forgotten your secret PIN code, The Default Pincode is 0000 and the Master Pincode is 2580.

- Check the dish and adjust it.

- Check the cable connection and correct it.

- Get out of UHF mode.

- Check channel and video output.

- Check the volume level of the TV and receiver.

- Check the mute status of TV and receiver.

- Check the cable connection and correct.

- Replace batteries.

- Aim the remote control unit directly to the receiver.

- Checking that nothing blocks the front panel.

- Press STB once on RCU and try the remote again

- Check the signal strength and the signal quality in the menu.

- Check the LNB and replace the LNB if neccessary.

- Check the LNB cable.

- Check the dish and adjust it.

User's Manual

SPECIFICATIONS

Specifications

Item

RCA Output

CVBS, L, R Output(Yellow, White, Red Jack) with Volume Control

Component Video(YUV) Out S-VHS Output 4-pin MINI Data Interface RS-232, Bit Rate: 115,200baud

Connector: 9-pin D-sub Male type

- USB : Type A Connector(FRONT/REAR) Wi-Fi only x 1

- Ethernet : 10/100Mbps, DHCP Supporting

Specification

IV. A/V & Date In/Out

Item

Input Voltage AC 90V ~ 250V, 50Hz ~ 60Hz Power Consumption Max 30W Standby Power Consumption <= 1 0W

Protection

Separate Internal Fuse The input shall the lighting protection

Specification

VI. Power Supply

Item

Size(WxHxD) 260mm x 50mm x205mm Weight 1.4 KG

Specification

VII. Physical Specification

Item

Operating Temperature 0 °C ~ 40 °C Storage Temperature -10 °C ~ 50 °C Operating Humidity Range 10~85% RH, Non-condensing Storage Humidity Range 5~90% RH, Non-condensing

Specification

VIII. Environmental Condition

User's Manual

SPECIFICATIONS

Specifications

Item

Specification

II. System & Memory

Main Processor 32-bit ARM946 RISC Processor

Flash Memory 2 Mbytes

System DRAM 32 Mbytes

Channel Capacity Digital Channel : 8000

Front 7-segment Display (4-digit)

Item

Specification

I. Tuner & Channel

Type 1 x F Type, IEC169-24, Female Frequency Rage 950MHz to 2150MHz RF Impedance 75 Ohm unbanlanced Signal Level -65 to -25 dBm

LNB Power 13.5/18.5Vdc +/- 5%, 0.5Amax, Overload Protected 22KHz Tone Frequency : 22KHz +/- 2KHz, 0.6Vpp +/- 0.2V DiSEqC Control Version1.0, 1.1, 1.2, Tone burst A/B Demodulation QPSK Input Symbol Rate 2~45 Ms/s, SCPC/MCPC FEC Decoder Convolution Code Rate 1/2, 2/3, 3/4, 5/6 and 7/8

With Constraint Length K = 7

Item

Transport Stream 13818-1 MPEG-2, H.264/AVC Transport stream Specification Profile Level MPEG-2 MP@ML Input Rate Max. 90Mbit/s Aspect Ratio 4:3, 16:9, Letter Box Frame Rate 25Hz for PAL, 30Hz for NTSC Video Resolution 720 X 576(PAL) / 720 X 480(NTSC) Teletext Through VBI Audio Decoding MPEG/Musicam Layer I & II Audio Mode Single Channel/Dual Channel Joint Stereo/Stereo Frequency Response 20~20kHz, <+/-2dB

60Hz~18KHz <+/- 0.5dB

Sampling Rate 32, 44.1, 48KHz

Specification

III. MPEG Transport Stream & A/V Decoding

Nanosat Nano Premium SE User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual