Manufacturer/Importer/Supplier/Distributor information
Manufacturer
Company name
Address
Telephone
E-mail
Contact person
Emergency phone number
NDT11P
NDT11P
3403.19.5000
Lubricant
None known.
Nano ProMT LLC
7427 Matthews Mint Hill Road, Suite 201
Mint Hill, NC 28227
Not available.
Not available.
Chris Hunter
Not available.
2. Hazard(s) identification
Physical hazards
Health hazards
Environmental hazards
OSHA defined hazards
Label elements
Signal word
Hazard statement
Precautionary statement
Prevention
Response
Classification not possibleFlammable aerosols
Category 2Skin corrosion/irritation
Category 2ASerious eye damage/eye irritation
Category 2Hazardous to the aquatic environment, acute
hazard
Category 2Hazardous to the aquatic environment,
long-term hazard
Not classified.
Warning
Toxic to aquatic life. Toxic to aquatic life with long lasting effects. Causes serious eye irritation.
Causes skin irritation.
Avoid release to the environment. Wear protective gloves. Wash thoroughly after handling. Wear
eye protection/face protection.
Collect spillage. If skin irritation occurs: Get medical advice/attention. If eye irritation persists: Get
medical advice/attention. Take off contaminated clothing and wash before reuse. If on skin: Wash
lenses, if present and easy to do. Continue rinsing.
Storage
Disposal
Hazard(s) not otherwise
classified (HNOC)
Supplemental information
Material name: Nano All-In-One Universal Penetrating Lubricant
NDT11P Version #: 01 Issue date: 08-09-2016
Not available.
Dispose of contents/container in accordance with local/regional/national/international regulations.
None known.
56.08% of the mixture consists of component(s) of unknown acute hazards to the aquatic
environment. 56.08% of the mixture consists of component(s) of unknown long-term hazards to
the aquatic environment.
SDS US
1 / 9
3. Composition/information on ingredients
Mixtures
CAS number%Common name and synonymsChemical name
Dioctyl Adipate
Carbon Dioxide
Bht (butylated Hydroxytoluene)
Phosphonic Acid, Polymers With
Diisopropanolamine N-tallow Alkyl
Derivs., Oleates (esters)
Calcium Carbonate
Paraffin Oils (petroleum), Catalytic
Dewaxed Heavy
Other components below reportable levels60 - < 70
*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.
103-23-1
124-38-9
128-37-0
141808-04-0
471-34-1
64742-70-7
4. First-aid measures
Inhalation
Skin contact
Eye contact
Ingestion
Most important
symptoms/effects, acute and
delayed
Indication of immediate
medical attention and special
treatment needed
General information
Move to fresh air. Call a physician if symptoms develop or persist. If symptoms develop move
victim to fresh air. Get medical attention if symptoms persist.
Wash off with soap and water. Get medical attention if irritation develops and persists. Wash with
plenty of soap and water. If skin irritation occurs: Get medical advice/attention. Remove
contaminated clothing. Wash contaminated clothing before reuse.
Rinse with water. Get medical attention if irritation develops and persists. If eye irritation persists:
Get medical advice/attention. Immediately flush eyes with plenty of water for at least 15 minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.
Get medical attention if symptoms occur. Rinse mouth. In the unlikely event of swallowing contact
a physician or poison control center.
Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred
vision. Skin irritation. May cause redness and pain.
Treat symptomatically. Symptoms may be delayed. Keep victim under observation. Provide
general supportive measures and treat symptomatically.
Ensure that medical personnel are aware of the material(s) involved, and take precautions to
protect themselves.
25.22
2.22
1.96
1.66
< 1
0.11
5. Fire-fighting measures
Suitable extinguishing media
Unsuitable extinguishing
media
Specific hazards arising from
the chemical
Special protective equipment
and precautions for firefighters
Fire fighting
equipment/instructions
General fire hazards
Carbon dioxide (CO2). Foam. Powder.
Do not use water jet as an extinguisher, as this will spread the fire.
Not applicable.
Not available.
Containers should be cooled with water to prevent vapor pressure build up.
No unusual fire or explosion hazards noted.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Material name: Nano All-In-One Universal Penetrating Lubricant
NDT11P Version #: 01 Issue date: 08-09-2016
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear
appropriate protective equipment and clothing during clean-up. Ensure adequate ventilation. Local
authorities should be advised if significant spillages cannot be contained. For personal protection,
see section 8 of the SDS. Do not touch damaged containers or spilled material unless wearing
appropriate protective clothing. Do not touch or walk through spilled material.
SDS US
2 / 9
water. For waste disposal, see section 13 of the SDS. Keep combustibles (wood, paper, oil, etc.)
Methods and materials for
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
US. ACGIH Threshold Limit Values
US. NIOSH: Pocket Guide to Chemical Hazards
containment and cleaning up
Environmental precautions
7. Handling and storage
Precautions for safe handling
Conditions for safe storage,
including any incompatibilities
Prevent product from entering drains. Stop the flow of material, if this is without risk.
Small Spills: Absorb in vermiculite, dry sand or earth and place into containers. Wipe up with
absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Isolate area until gas has dispersed.
Large Spills: Dike the spilled material, where this is possible.
Never return spills to original containers for re-use. Following product recovery, flush area with
away from spilled material. Refer to attached safety data sheets and/or instructions for use. Scoop
up used absorbent into drums or other appropriate container. Eliminate all ignition sources (no
smoking, flares, sparks, or flames in immediate area). Stop leak if you can do so without risk.
Move the cylinder to a safe and open area if the leak is irreparable.
Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all
environmental releases. Prevent further leakage or spillage if safe to do so. Contact local
authorities in case of spillage to drain/aquatic environment. Avoid discharge into drains, water
courses or onto the ground.
Provide adequate ventilation. Wear appropriate personal protective equipment. Avoid release to
the environment. Observe good industrial hygiene practices. Avoid contact with eyes, skin, and
clothing. Pressurized container: Do not pierce or burn, even after use. Do not spray on a naked
flame or any other incandescent material. Do not use if spray button is missing or defective. Do not
smoke while using or until sprayed surface is thoroughly dry. Use only in well-ventilated areas. Do
not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of
ignition. Ground and bond containers when transferring material. Avoid contact with eyes. Do not
re-use empty containers.
Store away from incompatible materials (see Section 10 of the SDS). Keep container tightly
closed. Store in original tightly closed container. Keep out of the reach of children. Do not handle
or store near an open flame, heat or other sources of ignition. Contents under pressure. Do not
puncture, incinerate or crush. Do not expose to heat or store at temperatures above 120°F/49°C
as can may burst. Avoid exposure to long periods of sunlight. Level 1 Aerosol.
STEL10 mg/m3Mist.Paraffin Oils (petroleum),
Catalytic Dewaxed Heavy
(CAS 64742-70-7)
TWA5 mg/m3Mist.
Biological limit values
Appropriate engineering
controls
No biological exposure limits noted for the ingredient(s).
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level. Provide
eyewash station. Eye wash facilities and emergency shower must be available when handling this
product.
Individual protection measures, such as personal protective equipment
Eye/face protection
Wear safety glasses with side shields (or goggles).
Skin protection
Hand protection
For prolonged or repeated skin contact use suitable protective gloves. Wear appropriate chemical
resistant gloves. Suitable gloves can be recommended by the glove supplier.
Other
Respiratory protection
Wear suitable protective clothing. Wear appropriate chemical resistant clothing.
In case of insufficient ventilation, wear suitable respiratory equipment. If permissible levels are
exceeded use NIOSH mechanical filter / organic vapor cartridge or an air-supplied respirator. Dust
mask.
Thermal hazards
General hygiene
considerations
Wear appropriate thermal protective clothing, when necessary.
Always observe good personal hygiene measures, such as washing after handling the material
and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment to remove contaminants. When using do not smoke.
ValueComponents
Form
10 mg/m3Total
30000 ppm
5000 ppm
9. Physical and chemical properties
Appearance
Physical state
Form
Color
Odor
Odor threshold
pH
Melting point/freezing point
Initial boiling point and boiling
range
Flash point
Evaporation rate
Flammability (solid, gas)
Upper/lower flammability or explosive limits
Flammability limit - lower
(%)
Flammability limit - upper
(%)
Explosive limit - lower (%)
Explosive limit - upper (%)
Opaque Liquid
Liquid, Gas.
Aerosol. Liquid.
Dark brown
Petroleum
Not available.
Not available.
-90.04 °F (-67.8 °C) estimated
469.04 °F (242.8 °C) estimated
250.0 °F (121.1 °C) estimated
Not available.
Not available.
0.8 % estimated
8.5 % estimated
Not available.
Not available.
Material name: Nano All-In-One Universal Penetrating Lubricant
NDT11P Version #: 01 Issue date: 08-09-2016
SDS US
4 / 9
Vapor pressure
Inhalation
Skin contact
Eye contact
Ingestion
Acute toxicity
Vapor density
Relative density
Solubility(ies)
Solubility (water)
Partition coefficient
(n-octanol/water)
Auto-ignition temperature
Decomposition temperature
Viscosity
Other information
Density
Explosive properties
Flame extension
Flammability (flash back)
Heat of combustion (NFPA
30B)
Oxidizing properties
Percent volatile
Specific gravity
10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Conditions to avoid
Incompatible materials
Hazardous decomposition
products
0.01 hPa estimated
Not available.
Not available.
Not available.
Not available.
530.6 °F (277 °C) estimated
Not available.
Not available.
7.80 lbs/gal estimated
Not explosive.
No Flame Extension
No
0.03 kJ/g estimated
Not oxidizing.
0.18 % estimated
0.93 estimated
Not available.
Not available.
Not available.
Contact with incompatible materials.
Not available.
Not available.
11. Toxicological information
Information on likely routes of exposure
Not available.
Causes skin irritation.
Direct contact with eyes may cause temporary irritation. Causes serious eye irritation.
Not available.
Symptoms related to the
physical, chemical and
toxicological
characteristics
Information on toxicological effects
Bht (butylated Hydroxytoluene) (CAS 128-37-0)
Acute
Oral
LD50Guinea pig10700 mg/kg
Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred
vision. Skin irritation. May cause redness and pain.
Mouse1040 mg/kg
Rat890 mg/kg
Test ResultsComponentsSpecies
Material name: Nano All-In-One Universal Penetrating Lubricant
NDT11P Version #: 01 Issue date: 08-09-2016
SDS US
5 / 9
Calcium Carbonate (CAS 471-34-1)
Respiratory sensitization
Carcinogenicity
Aspiration hazard
Other adverse effects
Acute
Oral
LD50Mouse6450 mg/kg
Rat6450 mg/kg
Dioctyl Adipate (CAS 103-23-1)
Acute
Oral
LD50Rat5.6 g/kg
* Estimates for product may be based on additional component data not shown.
Skin corrosion/irritation
Serious eye damage/eye
Causes skin irritation.
Direct contact with eyes may cause temporary irritation. Causes serious eye irritation.
irritation
Respiratory or skin sensitization
Not available.
Skin sensitization
Germ cell mutagenicity
Not available.
Not available.
This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA.
IARC Monographs. Overall Evaluation of Carcinogenicity
Bht (butylated Hydroxytoluene) (CAS 128-37-0)3 Not classifiable as to carcinogenicity to humans.
Dioctyl Adipate (CAS 103-23-1)3 Not classifiable as to carcinogenicity to humans.
waterways or ditches with chemical or used container. Contents under pressure. Do not puncture,
warnings even after container is emptied.
Disposal instructions
Local disposal regulations
Hazardous waste code
Waste from residues / unused
products
Contaminated packaging
14. Transport information
DOT
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Packing group
Special precautions for user
IATA
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Packing group
Environmental hazards
Special precautions for user
IMDG
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Packing group
Environmental hazards
Marine pollutant
EmS
Special precautions for user
Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
Marine pollutant
Do not allow this material to drain into sewers/water supplies. Dispose of contents/container in
accordance with local/regional/national/international regulations. Do not contaminate ponds,
incinerate or crush. Dispose in accordance with all applicable regulations. Collect and reclaim or
dispose in sealed containers at licensed waste disposal site.
Dispose in accordance with all applicable regulations.
The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Dispose of in accordance with local regulations. Empty containers or liners may retain some
product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Do not re-use empty containers. Empty containers should be taken to an approved waste handling
site for recycling or disposal. Since emptied containers may retain product residue, follow label
Not available.
Consumer Commodity
ORM-D
Not applicable.
Read safety instructions, SDS and emergency procedures before handling.
UN1950
Aerosol, non-flammable
2.2
Not applicable.
Yes
Read safety instructions, SDS and emergency procedures before handling.
UN1950
Aerosols, MARINE POLLUTANT
2.2
Not applicable.
Yes
F-D, S-U
Read safety instructions, SDS and emergency procedures before handling.
Not available.
Material name: Nano All-In-One Universal Penetrating Lubricant
Paraffin Oils (petroleum), Catalytic Dewaxed Heavy (CAS 64742-70-7)
US. Massachusetts RTK - Substance List
Bht (butylated Hydroxytoluene) (CAS 128-37-0)
Calcium Carbonate (CAS 471-34-1)
Carbon Dioxide (CAS 124-38-9)
Dioctyl Adipate (CAS 103-23-1)
Paraffin Oils (petroleum), Catalytic Dewaxed Heavy (CAS 64742-70-7)
US. New Jersey Worker and Community Right-to-Know Act
Bht (butylated Hydroxytoluene) (CAS 128-37-0)
Calcium Carbonate (CAS 471-34-1)
Carbon Dioxide (CAS 124-38-9)
Dioctyl Adipate (CAS 103-23-1)
US. Pennsylvania Worker and Community Right-to-Know Law
Bht (butylated Hydroxytoluene) (CAS 128-37-0)
Calcium Carbonate (CAS 471-34-1)
Carbon Dioxide (CAS 124-38-9)
Dioctyl Adipate (CAS 103-23-1)
Paraffin Oils (petroleum), Catalytic Dewaxed Heavy (CAS 64742-70-7)
US. Rhode Island RTK
Not regulated.
Material name: Nano All-In-One Universal Penetrating Lubricant
NDT11P Version #: 01 Issue date: 08-09-2016
SDS US
8 / 9
US. California Proposition 65
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain
any chemicals currently listed as carcinogens or reproductive toxins.
International Inventories
Country(s) or regionInventory nameOn inventory (yes/no)*
Substances (EINECS)
(PICCS)
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
country(s).
16. Other information, including date of preparation or last revision
Issue date
Version #
HMIS® ratings
NFPA ratings
NFPA ratings
08-09-2016
01
Health: 2
Flammability: 0
Physical hazard: 0
Health: 2
Flammability: 0
Instability: 0
0
02
NoAustraliaAustralian Inventory of Chemical Substances (AICS)
YesCanadaDomestic Substances List (DSL)
NoCanadaNon-Domestic Substances List (NDSL)
NoChinaInventory of Existing Chemical Substances in China (IECSC)
NoEuropeEuropean Inventory of Existing Commercial Chemical
NoEuropeEuropean List of Notified Chemical Substances (ELINCS)
NoJapanInventory of Existing and New Chemical Substances (ENCS)
NoKoreaExisting Chemicals List (ECL)
NoNew ZealandNew Zealand Inventory
NoPhilippinesPhilippine Inventory of Chemicals and Chemical Substances
YesUnited States & Puerto RicoToxic Substances Control Act (TSCA) Inventory
Disclaimer
Nano ProMT LLC cannot anticipate all conditions under which this information and its product, or
the products of other manufacturers in combination with its product, may be used. It is the user’s
responsibility to ensure safe conditions for handling, storage and disposal of the product, and to
assume liability for loss, injury, damage or expense due to improper use. The information in the
sheet was written based on the best knowledge and experience currently available.
Material name: Nano All-In-One Universal Penetrating Lubricant
NDT11P Version #: 01 Issue date: 08-09-2016
SDS US
9 / 9
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.