SAFETY DATA SHEET
well-ventilated area. Avoid release to the environment. Wear protective gloves.
1. Identification
Nano Dry LubricantProduct identifier
Other means of identification
SDS number
Part No.
Tariff code
Recommended use
Recommended restrictions
Manufacturer/Importer/Supplier/Distributor information
Manufacturer
Company name
Address
Telephone
E-mail
Contact person
Emergency phone number
NDT11DCA
NDT11DCA
2905.12.0050
Dry Lubricant
None known.
Nano ProMT LLC
7427 Matthews Mint Hill Road, Suite 201
Mint Hill, NC 28227
Not available.
Not available.
Chris Hunter
Not available.
2. Hazard(s) identification
Physical hazards
Health hazards
Environmental hazards
OSHA defined hazards
Label elements
Signal word
Hazard statement
Precautionary statement
Prevention
Category 1Flammable aerosols
Category 2Skin corrosion/irritation
Category 3 narcotic effectsSpecific target organ toxicity, single exposure
Category 2Specific target organ toxicity, repeated
exposure
Category 2Hazardous to the aquatic environment,
long-term hazard
Not classified.
Danger
Extremely flammable aerosol. Causes skin irritation. May cause drowsiness or dizziness. May
cause damage to organs through prolonged or repeated exposure. Toxic to aquatic life with long
lasting effects.
Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open
flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Do
not breathe mist or vapor. Wash thoroughly after handling. Use only outdoors or in a
Response
Storage
Disposal
Hazard(s) not otherwise
classified (HNOC)
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
If on skin: Wash with plenty of water. If inhaled: Remove person to fresh air and keep comfortable
for breathing. Call a poison center/doctor if you feel unwell. If skin irritation occurs: Get medical
advice/attention. Take off contaminated clothing and wash before reuse. Collect spillage.
Store in a well-ventilated place. Keep container tightly closed. Store locked up. Protect from
sunlight. Do not expose to temperatures exceeding 50°C/122°F.
Dispose of contents/container in accordance with local/regional/national/international regulations.
None known.
SDS US
1 / 10
Supplemental information
water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose
76.8% of the mixture consists of component(s) of unknown long-term hazards to the aquatic
environment.
3. Composition/information on ingredients
Mixtures
CAS number %Common name and synonymsChemical name
Isopropyl Alcohol
Propane
Heptane
Solvent Naphtha (petroleum),
Medium Aliph.
BENZENE, DIMETHYL
Aluminium Oxide
Other components below reportable levels 1.4
*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.
67-63-0
74-98-6
142-82-5
64742-88-7
1330-20-7
1344-28-1
4. First-aid measures
Inhalation
Skin contact
Eye contact
Ingestion
Most important
symptoms/effects, acute and
delayed
Indication of immediate
medical attention and special
treatment needed
General information
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Remove contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Get
medical advice/attention. Wash contaminated clothing before reuse.
Rinse with water. Get medical attention if irritation develops and persists.
In the unlikely event of swallowing contact a physician or poison control center. Rinse mouth.
May cause drowsiness and dizziness. Headache. Nausea, vomiting. Skin irritation. May cause
redness and pain. Prolonged exposure may cause chronic effects.
Provide general supportive measures and treat symptomatically. Keep victim under observation.
Symptoms may be delayed.
If you feel unwell, seek medical advice (show the label where possible). Ensure that medical
personnel are aware of the material(s) involved, and take precautions to protect themselves.
46.8
30
21
0.75
0.04
0.01
5. Fire-fighting measures
Suitable extinguishing media
Unsuitable extinguishing
media
Specific hazards arising from
the chemical
Special protective equipment
and precautions for firefighters
Fire fighting
equipment/instructions
Specific methods
General fire hazards
Powder. Foam. Carbon dioxide (CO2).
Do not use water jet as an extinguisher, as this will spread the fire.
Contents under pressure. Pressurized container may explode when exposed to heat or flame.
During fire, gases hazardous to health may be formed.
Firefighters must use standard protective equipment including flame retardant coat, helmet with
face shield, gloves, rubber boots, and in enclosed spaces, SCBA.
Move containers from fire area if you can do so without risk. Containers should be cooled with
holder or monitor nozzles, if possible. If not, withdraw and let fire burn out.
Use standard firefighting procedures and consider the hazards of other involved materials. Move
containers from fire area if you can do so without risk. In the event of fire and/or explosion do not
breathe fumes.
Extremely flammable aerosol.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear
appropriate protective equipment and clothing during clean-up. Do not breathe mist or vapor. Do
not touch damaged containers or spilled material unless wearing appropriate protective clothing.
Ventilate closed spaces before entering them. Local authorities should be advised if significant
spillages cannot be contained. For personal protection, see section 8 of the SDS.
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
SDS US
2 / 10
water surface. This material is classified as a water pollutant under the Clean Water Act and
Methods and materials for
while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or
well-ventilated areas. Wear appropriate personal protective equipment. Avoid release to the
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
US. ACGIH Threshold Limit Values
containment and cleaning up
Environmental precautions
7. Handling and storage
Precautions for safe handling
Conditions for safe storage,
including any incompatibilities
Refer to attached safety data sheets and/or instructions for use. Keep combustibles (wood, paper,
oil, etc.) away from spilled material. The product is immiscible with water and will spread on the
should be prevented from contaminating soil or from entering sewage and drainage systems which
lead to waterways. Stop leak if you can do so without risk. Move the cylinder to a safe and open
area if the leak is irreparable. Cover with plastic sheet to prevent spreading. Absorb in vermiculite,
dry sand or earth and place into containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination. For waste disposal, see section 13 of the SDS.
Avoid release to the environment. Prevent further leakage or spillage if safe to do so. Avoid
discharge into drains, water courses or onto the ground. Inform appropriate managerial or
supervisory personnel of all environmental releases.
Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing
or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke
expose containers to heat, flame, sparks, or other sources of ignition. All equipment used when
handling the product must be grounded. Do not re-use empty containers. Do not breathe mist or
vapor. Avoid contact with eyes, skin, and clothing. Avoid prolonged exposure. Use only in
environment. Observe good industrial hygiene practices.
Level 2 Aerosol.
Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open
flame, heat or other sources of ignition. This material can accumulate static charge which may
cause spark and become an ignition source. Keep out of the reach of children. Store away from
incompatible materials (see Section 10 of the SDS).
8. Exposure controls/personal protection
Occupational exposure limits
Type
PEL 5 mg/m3 Respirable fraction.Aluminium Oxide (CAS
1344-28-1)
PEL 435 mg/m3BENZENE, DIMETHYL
(CAS 1330-20-7)
PEL 2000 mg/m3Heptane (CAS 142-82-5)
PEL 980 mg/m3Isopropyl Alcohol (CAS
67-63-0)
PEL 1800 mg/m3Propane (CAS 74-98-6)
Type
TWA 1 mg/m3 Respirable fraction.Aluminium Oxide (CAS
1344-28-1)
STEL 150 ppmBENZENE, DIMETHYL
(CAS 1330-20-7)
TWA 100 ppm
STEL 500 ppmHeptane (CAS 142-82-5)
TWA 400 ppm
STEL 400 ppmIsopropyl Alcohol (CAS
67-63-0)
TWA 200 ppm
TWA 200 mg/m3 Non-aerosol.Solvent Naphtha
(petroleum), Medium Aliph.
(CAS 64742-88-7)
ValueComponents
Form
15 mg/m3 Total dust.
100 ppm
500 ppm
400 ppm
1000 ppm
ValueComponents
Form
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
SDS US
3 / 10
US. NIOSH: Pocket Guide to Chemical Hazards
67-63-0)
ACGIH Biological Exposure Indices
wash facilities and emergency shower must be available when handling this product.
wear safety glasses with side shields (or goggles)
with White particles
(petroleum), Medium Aliph.
(CAS 64742-88-7)
Biological limit values
ValueComponents Type
Ceiling 1800 mg/m3Heptane (CAS 142-82-5)
440 ppm
TWA 350 mg/m3
85 ppm
STEL 1225 mg/m3Isopropyl Alcohol (CAS
500 ppm
TWA 980 mg/m3
400 ppm
TWA 1800 mg/m3Propane (CAS 74-98-6)
1000 ppm
TWA 100 mg/m3Solvent Naphtha
ValueComponents Determinant Specimen Sampling Time
BENZENE, DIMETHYL
(CAS 1330-20-7)
Isopropyl Alcohol (CAS
1.5 g/g Methylhippuric
acids
40 mg/l Acetone Urine
67-63-0)
* - For sampling details, please see the source document.
Exposure guidelines
US ACGIH Threshold Limit Values: Skin designation
Solvent Naphtha (petroleum), Medium Aliph. (CAS
Can be absorbed through the skin.
64742-88-7)
Appropriate engineering
controls
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level. Eye
Individual protection measures, such as personal protective equipment
Eye/face protection
Skin protection
Hand protection
Wear appropriate chemical resistant gloves. Suitable gloves can be recommended by the glove
supplier.
Other
Respiratory protection
Thermal hazards
General hygiene
considerations
Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.
Chemical respirator with organic vapor cartridge and full facepiece if threshold limits are exceeded.
Wear appropriate thermal protective clothing, when necessary.
When using do not smoke. Always observe good personal hygiene measures, such as washing
after handling the material and before eating, drinking, and/or smoking. Routinely wash work
clothing and protective equipment to remove contaminants.
Creatinine in
urine
*
*
9. Physical and chemical properties
Appearance
Physical state
Form
Color
Odor
Odor threshold
pH
Melting point/freezing point
Initial boiling point and boiling
range
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
Liquid
Liquid.
Aerosol.
Solvent.odor
Not available.
Not available.
-305.68 °F (-187.6 °C) estimated
-43.78 °F (-42.1 °C) estimated
SDS US
4 / 10
Flash point
Skin contact
Eye contact
Ingestion
Evaporation rate
Flammability (solid, gas)
< 0 °F (< -17.8 °C) Tag Closed Cup
Not available.
Not applicable.
Upper/lower flammability or explosive limits
Flammability limit - lower
2.4 % estimated
(%)
Flammability limit - upper
12 % estimated
(%)
Explosive limit - lower (%)
Explosive limit - upper (%)
Vapor pressure
Vapor density
Relative density
Not available.
Not available.
2966.21 hPa estimated
Not available.
Not available.
Solubility(ies)
Solubility (water)
Partition coefficient
Insoluble
Not available.
(n-octanol/water)
Auto-ignition temperature
Decomposition temperature
Viscosity
750.2 °F (399 °C) estimated
Not available.
Not available.
Other information
Density
Explosive properties
Flame extension
Flammability (flash back)
Flammability class
Heat of combustion (NFPA
6.34 lbs/gal
Not explosive.
> 21 in
No
Flammable IA estimated
34.95 kJ/g estimated
30B)
Oxidizing properties
Percent volatile
Specific gravity
VOC
Not oxidizing.
46.84 % estimated
0.76
97.8 % w/w
10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Conditions to avoid
Incompatible materials
Hazardous decomposition
products
The product is stable and non-reactive under normal conditions of use, storage and transport.
Material is stable under normal conditions.
No dangerous reaction known under conditions of normal use.
Avoid temperatures exceeding the flash point. Contact with incompatible materials.
Strong oxidizing agents.
No hazardous decomposition products are known.
11. Toxicological information
Information on likely routes of exposure
Inhalation
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
May cause damage to organs through prolonged or repeated exposure by inhalation. May cause
drowsiness and dizziness. Headache. Nausea, vomiting.
Causes skin irritation.
Direct contact with eyes may cause temporary irritation.
Expected to be a low ingestion hazard.
SDS US
5 / 10
Symptoms related to the
Acute toxicity
Respiratory sensitization
Carcinogenicity
physical, chemical and
Headache. May cause drowsiness and dizziness. Nausea, vomiting. Skin irritation. May cause
redness and pain.
toxicological
characteristics
Information on toxicological effects
Narcotic effects.
BENZENE, DIMETHYL (CAS 1330-20-7)
Acute
Dermal
LD50 Rabbit > 43 g/kg
Inhalation
LC50 Mouse 3907 mg/l, 6 Hours
Rat 6350 mg/l, 4 Hours
Oral
LD50 Mouse 1590 mg/kg
Rat 3523 - 8600 mg/kg
Heptane (CAS 142-82-5)
Acute
Inhalation
LC50 Rat 103 mg/l, 4 Hours
LD50 Mouse 75 mg/l, 2 Hours
Isopropyl Alcohol (CAS 67-63-0)
Acute
Dermal
LD50 Rabbit 12800 mg/kg
Oral
LD50 Dog 4797 mg/kg
Mouse 3600 mg/kg
Rabbit 5.03 g/kg
Rat 4.7 g/kg
Propane (CAS 74-98-6)
Acute
Inhalation
LC50 Rat > 1442.847 mg/l, 15 Minutes
Test ResultsComponents Species
* Estimates for product may be based on additional component data not shown.
Skin corrosion/irritation
Serious eye damage/eye
irritation
Respiratory or skin sensitization
Skin sensitization
Germ cell mutagenicity
IARC Monographs. Overall Evaluation of Carcinogenicity
BENZENE, DIMETHYL (CAS 1330-20-7) 3 Not classifiable as to carcinogenicity to humans.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not regulated.
US. National Toxicology Program (NTP) Report on Carcinogens
Not listed.
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
Causes skin irritation.
Direct contact with eyes may cause temporary irritation.
Not a respiratory sensitizer.
This product is not expected to cause skin sensitization.
No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA.
SDS US
6 / 10
Reproductive toxicity
Aspiration hazard
Partition coefficient n-octanol / water (log Kow)
Specific target organ
This product is not expected to cause reproductive or developmental effects.
May cause drowsiness and dizziness.
toxicity - single exposure
Specific target organ
May cause damage to organs through prolonged or repeated exposure.
toxicity - repeated
exposure
Not an aspiration hazard.
Chronic effects
May cause damage to organs through prolonged or repeated exposure. Prolonged inhalation may
be harmful.
12. Ecological information
Ecotoxicity
Components Test ResultsSpecies
BENZENE, DIMETHYL (CAS 1330-20-7)
Aquatic
Heptane (CAS 142-82-5)
Aquatic
Isopropyl Alcohol (CAS 67-63-0)
Aquatic
Toxic to aquatic life with long lasting effects.
LC50Fish 7.711 - 9.591 mg/l, 96 hoursBluegill (Lepomis macrochirus)
LC50Fish 375 mg/l, 96 hoursMozambique tilapia (Tilapia
LC50Fish > 1400 mg/l, 96 hoursBluegill (Lepomis macrochirus)
mossambica)
* Estimates for product may be based on additional component data not shown.
Persistence and degradability
Bioaccumulative potential
No data is available on the degradability of this product.
BENZENE, DIMETHYL 3.12 - 3.2
Heptane 4.66
Isopropyl Alcohol 0.05
Propane 2.36
Mobility in soil
Other adverse effects
No data available.
No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Disposal instructions
Local disposal regulations
Hazardous waste code
Waste from residues / unused
products
Contaminated packaging
Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Contents
under pressure. Do not puncture, incinerate or crush. Do not allow this material to drain into
sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used
container. Dispose of contents/container in accordance with local/regional/national/international
regulations.
Dispose in accordance with all applicable regulations.
The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Dispose of in accordance with local regulations. Empty containers or liners may retain some
product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Since emptied containers may retain product residue, follow label warnings even after container is
emptied. Empty containers should be taken to an approved waste handling site for recycling or
disposal. Do not re-use empty containers.
14. Transport information
DOT
UN number
UN proper shipping name
Transport hazard class(es)
Class
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
Not available.
Consumer Commodity
ORM-D
SDS US
7 / 10
Subsidiary risk
Packing group
Special precautions for user
Special provisions
Packaging exceptions
Packaging non bulk
Packaging bulk
IATA
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Packing group
Environmental hazards
ERG Code
Special precautions for user
Other information
Passenger and cargo
aircraft
Cargo aircraft only
IMDG
UN number
UN proper shipping name
Transport hazard class(es)
Class
Subsidiary risk
Packing group
Environmental hazards
Marine pollutant
EmS
Special precautions for user
Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
IATA; IMDG
Not applicable.
Read safety instructions, SDS and emergency procedures before handling.
IB2, T4, TP1
4b, 150
202
242
UN1950
Aerosol, flammable
2.1
Not applicable.
Yes
9L
Read safety instructions, SDS and emergency procedures before handling.
Allowed with restrictions.
Allowed with restrictions.
UN1950
Aerosols, MARINE POLLUTANT
2.1
Not applicable.
Yes
F-D, S-U
Read safety instructions, SDS and emergency procedures before handling.
Not established.
Marine pollutant
General information
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
IMDG Regulated Marine Pollutant. DOT Regulated Marine Pollutant.
SDS US
8 / 10
15. Regulatory information
US federal regulations
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40 CFR 302.4)
BENZENE, DIMETHYL (CAS 1330-20-7) Listed.
Heptane (CAS 142-82-5) Listed.
Isopropyl Alcohol (CAS 67-63-0) Listed.
Propane (CAS 74-98-6) Listed.
SARA 304 Emergency release notification
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not regulated.
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Hazard categories
SARA 302 Extremely hazardous substance
Not listed.
SARA 311/312 Hazardous
chemical
SARA 313 (TRI reporting)
Chemical name % by wt.
Isopropyl Alcohol 46.867-63-0
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
BENZENE, DIMETHYL (CAS 1330-20-7)
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Propane (CAS 74-98-6)
Safe Drinking Water Act
(SDWA)
FEMA Priority Substances Respiratory Health and Safety in the Flavor Manufacturing Workplace
Isopropyl Alcohol (CAS 67-63-0) Low priority
US state regulations
US. California Controlled Substances. CA Department of Justice (California Health and Safety Code Section 11100)
Not listed.
US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd.
(a))
BENZENE, DIMETHYL (CAS 1330-20-7)
Isopropyl Alcohol (CAS 67-63-0)
Solvent Naphtha (petroleum), Medium Aliph. (CAS 64742-88-7)
US. Massachusetts RTK - Substance List
Aluminium Oxide (CAS 1344-28-1)
BENZENE, DIMETHYL (CAS 1330-20-7)
Heptane (CAS 142-82-5)
Isopropyl Alcohol (CAS 67-63-0)
Propane (CAS 74-98-6)
Solvent Naphtha (petroleum), Medium Aliph. (CAS 64742-88-7)
US. New Jersey Worker and Community Right-to-Know Act
Aluminium Oxide (CAS 1344-28-1)
BENZENE, DIMETHYL (CAS 1330-20-7)
Heptane (CAS 142-82-5)
Isopropyl Alcohol (CAS 67-63-0)
Propane (CAS 74-98-6)
Solvent Naphtha (petroleum), Medium Aliph. (CAS 64742-88-7)
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
Immediate Hazard - Yes
Delayed Hazard - Yes
Fire Hazard - Yes
Pressure Hazard - No
Reactivity Hazard - No
No
CAS number
Not regulated.
SDS US
9 / 10
US. Pennsylvania Worker and Community Right-to-Know Law
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
Aluminium Oxide (CAS 1344-28-1)
BENZENE, DIMETHYL (CAS 1330-20-7)
Heptane (CAS 142-82-5)
Isopropyl Alcohol (CAS 67-63-0)
Propane (CAS 74-98-6)
Solvent Naphtha (petroleum), Medium Aliph. (CAS 64742-88-7)
US. Rhode Island RTK
Aluminium Oxide (CAS 1344-28-1)
BENZENE, DIMETHYL (CAS 1330-20-7)
Isopropyl Alcohol (CAS 67-63-0)
Propane (CAS 74-98-6)
US. California Proposition 65
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain
any chemicals currently listed as carcinogens or reproductive toxins.
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Substances (EINECS)
(PICCS)
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
YesAustralia Australian Inventory of Chemical Substances (AICS)
YesCanada Domestic Substances List (DSL)
NoCanada Non-Domestic Substances List (NDSL)
YesChina Inventory of Existing Chemical Substances in China (IECSC)
YesEurope European Inventory of Existing Commercial Chemical
NoEurope European List of Notified Chemical Substances (ELINCS)
NoJapan Inventory of Existing and New Chemical Substances (ENCS)
YesKorea Existing Chemicals List (ECL)
YesNew Zealand New Zealand Inventory
YesPhilippines Philippine Inventory of Chemicals and Chemical Substances
YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory
country(s).
16. Other information, including date of preparation or last revision
Issue date
Version #
HMIS® ratings
NFPA ratings
NFPA ratings
Disclaimer
07-21-2016
01
Health: 2*
Flammability: 4
Physical hazard: 0
Health: 2
Flammability: 4
Instability: 0
4
02
The information provided in this Safety Data Sheet is correct to the best of our knowledge,
information and belief at the date of its publication. The information given is designed only as a
guidance for safe handling, use, processing, storage, transportation, disposal and release and is
not to be considered a warranty or quality specification. The information relates only to the specific
material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
Material name: Nano Dry Lubricant
NDT11DCA Version #: 01 Issue date: 07-21-2016
SDS US
10 / 10
Loading...