NAIS TN2-L2-H-9V, TN2-L2-H-6V, TN2-L2-H-5V, TN2-L2-H-4.5V, TN2-L2-H-24V Datasheet
...
❇
SLIM POLARIZED RELAY
FEATURES
• Small size for minimal PC board
mounting requirements
• Small header area makes higher density mounting possible
• High sensitivity: 140 mW nominal operating power (single side stable 3-12
V type)
14
.551
5.6
.220
9.8
.386
mm inch
SPECIFICATIONS
Contact
Arrangement 2 Form C
Initial contact resistance, max.
(By voltage drop 6 V DC 1A)
Contact material Gold-clad silver
Nominal switching capacity
(resistive load)
Max. switching power
Rating
(resistive load)
Max. switching voltage 110 V DC,125 V AC
Max. switching current 1 A
Min. switching capacity ❇ 1 10 µ A 10 mV DC
Single side stable
Nominal
operating
power
1 coil latching
2 coil latching
Mechanical (at 180 cpm) 10
Expected
life (min.
operations)
Electrical
(at 20 cpm)
1 A 30 V DC
resistive load
0.5 A 125 V AC
resistive load
Note:
1This value can change due to the switching frequency, en vironmental conditions,
and desired reliability level, therefore it is recommended to chec k this with the actual load.
Remarks
* Specifications will vary with foreign standards certification ratings.
1
*
Measurement at same location as "Initial breakdown voltage" section.
2
By resistive method, nominal voltage applied to the coil; contact carrying current:
*
1 A.
3
*
Nominal voltage applied to the coil, excluding contact bounce time.
4
Nominal voltage applied to the coil, excluding contact bounce time without diode.
*
60 m Ω
1 A 30 V DC,
0.5 A 125 V AC
30 W, 62.5 VA
140 mW (3 to 12 V DC)
200 mW (24 V DC)
300 mW (48 V DC)
100 mW (3 to 12 V DC)
150 mW (24 V DC)
200 mW (3 to 12 V DC)
300 mW (24 V DC)
8
5
2 × 10
5
10
TN-RELAYS
• Surge voltage withstand: 1500 V FCC
Part 68
• Sealed construction allows automatic
cleaning
• Self-clinching terminal also available
Characteristics
Initial insulation resistance*
Between open
Initial
breakdown
voltage
contacts
Between contact and
coil
Between contact sets
FCC surge voltage between open
contacts
Temperature rise*
2
(at 20 ° C) Max. 50 ° C
Operate time [Set time]*
Release time [Reset time]*
(at 20 ° C)
Shock resistance
Vibration resistance
Conditions for operation, transport and
8
storage*
(Not freezing and
condensing at low
temperature)
Unit weight Approx. 1.5 g .053 oz
5
*
Half-wave pulse of sine wave: 11 ms; detection time: 10 µ s.
6
Half-wave pulse of sine wave: 6 ms.
*
7
*
Detection time: 10 µ s.
8
*
Refer to 4. Conditions f or operation, transport and storage mentioned in Cautions
for use (Page 178).
1
Min. 1,000 M Ω (at 500 V DC)
750 Vrms for 1 min.
(Detection current: 10 mA)
1,000 Vrms for 1 min.
(Detection current: 10 mA)
1,000 Vrms for 1 min.
(Detection current: 10 mA)
1,500 V
3
(at 20 ° C)
4
Max. 3 ms (Approx. 2 ms)
[Max. 3 ms (Approx. 2 ms)]
Max. 3 ms (Approx. 1 ms)
[Max. 3 ms (Approx. 2 ms)]
Functional*
Destructive*
Functional*
Destructive
Ambient
temperature
5
6
7
Min. 490 m/s
Min. 980 m/s
176.4 m/s
at double amplitude of 3 mm
2
294 m/s
at double amplitude of 5 mm
–40 ° C to +70 ° C
–40 ° F to +158 ° F
2
{50G}
2
{100G}
2
{18G}, 10 to 55 Hz
{30G}, 10 to 55 Hz
Humidity 5 to 85% R.H.
ORDERING INFORMATION
Ex. TN 2 L2 H 12V
Contact arrangement Operating function Terminal shape Coil voltage(DC)
2: 2 Form C Nil: Standard PC board terminal
*48 V coil type: Single side stable only
Note:
AgPd stationary contact types available for high resistance against contact sticking.
When ordering, please add suffix “–3” like TN2–12V–3.
150
Nil: Single side stable
L: 1 coil latching
L2: 2 coil latching
H: Self-clinching terminal
3,4.5,5,6,9,12,
24,48*V
2.54
.100
10.16
.400
2.54
.100
10-1.0 dia. hole
10-.039 dia. hole
Direction indication*
10 9 8 7 6
1 2 3 4 5
Direction indication*
10 9 8 7 6
1 2 3 4 5
Ω ( ±
Ω ( ±
Ω ( ±
TYPES AND COIL DATA (at 20 ° C 68 ° F)
1. Single side stable
Standard PC
board terminal
Part No.
Self-clinching
terminal
Nominal
voltage,
V DC
Pick-up
voltage,
V DC (max.)
Drop-out
voltage,
V DC (min.)
TN2-3 V TN2-H-3 V 3 2.25 0.3 46.7 64.3 140 4.5
TN2-4.5 V TN2-H-4.5 V 4.5 3.38 0.45 31.1 145 140 6.7
TN2-5 V TN2-H-5 V 5 3.75 0.5 28.1 178 140 7.5
TN2-6 V TN2-H-6 V 6 4.5 0.6 23.3 257 140 9
TN2-9 V TN2-H-9 V 9 6.75 0.9 15.5 579 140 13.5
TN2-12 V TN2-H-12 V 12 9 1.2 11.7 1,028 140 18
TN2-24 V TN2-H-24 V 24 18 2.4 8.3 2,880 200 36
TN2-48 V TN2-H-48 V 48 36 4.8 6.25 7,680 300 57.6
2. 1 Coil latching
Part No.
Standard PC
board terminal
Self-clinching
terminal
TN2-L-3 V TN2-L-H-3 V 3 2.25 2.25 33.3 90 100 4.5
TN2-L-4.5 V TN2-L-H-4.5 V 4.5 3.38 3.38 22.2 202.5 100 6.7
TN2-L-5 V TN2-L-H-5 V 5 3.75 3.75 20 250 100 7.5
TN2-L-6 V TN2-L-H-6 V 6 4.5 4.5 16.7 360 100 9
TN2-L-9 V TN2-L-H-9 V 9 6.75 6.75 11.1 810 100 13.5
TN2-L-12 V TN2-L-H-12 V 12 9 9 8.3 1,440 100 18
TN2-L-24 V TN2-L-H-24 V 24 18 18 6.3 3,840 150 36
Nominal
voltage,
V DC
Set voltage,
V DC (max.)
Reset voltage,
V DC (max.)
3. 2 Coil latching
Part No.
Standard PC
board terminal
Self-clinching
terminal
TN2-L2-3 V TN2-L2-H-3 V 3 2.25 2.25 66.7 45 200 4.5
TN2-L2-4.5 V TN2-L2-H-4.5 V 4.5 3.38 3.38 44.4 101.2 200 6.7
TN2-L2-5 V TN2-L2-H-5 V 5 3.75 3.75 40 125 200 7.5
TN2-L2-6 V TN2-L2-H-6 V 6 4.5 4.5 33.3 180 200 9
TN2-L2-9 V TN2-L2-H-9 V 9 6.75 6.75 22.2 405 200 13.5
TN2-L2-12 V TN2-L2-H-12 V 12 9 9 16.7 720 200 18
TN2-L2-24 V TN2-L2-H-24 V 24 18 18 12.5 1,920 300 28.8
Notes:
1. Specified value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
2. Standard packing: Tube: 50 pcs.; Case: 1,000 pcs.
3. In case of 5 V drive circuit, it is recommended to use 4.5 V type relay.
4. AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "–3" like TN2-12V -3.
Nominal
voltage,
V DC
Set voltage,
V DC (max.)
Reset voltage,
V DC (max.)
Nominal
operating
current,
mA ( ± 10%)
Nominal
operating
current,
mA ( ± 10%)
Nominal
operating
current,
mA ( ± 10%)
Coil
resistance,
10%)
Coil
resistance,
10%)
Coil
resistance,
10%)
Nominal
operating
power,
mW
Nominal
operating
power,
mW
Nominal
operating
power,
mW
Max.
allowable
voltage,
V DC
Max.
allowable
voltage,
V DC
Max.
allowable
voltage,
V DC
TN
DIMENSIONS
3.5
.138
3.5
.138
Standard PC board terminal
14
551
9.5
9.8
.374
.386
2.54
0.5
.100
.020
Self-clinching terminal
14
551
9.5
9.8
.374
.386
2.54
0.5
.100
.020
General tolerance: ± 0.3 ± .012
1.385
.055
1.385
.055
5.6
.220
5.6
.220
0.25
.010
2.54
.100
0.25
.010
• Single side stable
(Deenergized condition)
2.54
.100
Direction indication*
PC board pattern (Copper-side view)
Schematic (Bottom view)
• 1-coil latching
(Reset condition)
1 2 3 4 5
10 9 8 7 6
mm inch
Tolerance: ± 0.1 ± .004
• 2-coil latching
(Reset condition)
*Orientation stripe located on top of relay
151
Loading...