How it Works
Naim1
Loading...
C
H
N
Loading...
Loading...
HDX-SSD
REFERENCE MANUAL
28 pgs1.25 Mb0
Table of contents
Loading...

Naim1 HDX-SSD, HDX-SSD REFERENCE MANUAL

REFERENCE MANUAL
HDX-SSD-SSD HARD DISK PLAYER
ENGLISH

Contents

Section Page Contents 1 HDX-SSD Hard Disk Player Introduction 1
1.1 HDX-SSD User Interfaces 1
1.2 HDX-SSD Interface Options 2
2 Getting Started 3
2.1 Internet/Network Connections 3
2.2 Power Supply Upgrade 3
2.3 Audio Connections 3
2.4 Switch On 4
2.5 External Screen Setup 4
2.6 First Use 4
2.7 Software Upgrade 4
2.8 Switching Off 4
2.9 Data Backup 5
5 Playback 17
6 Ripping 18
7 External Storage 19
3 Getting Connected 6
3.1 HDX-SSD Rear Panel 6
3.2 HDX-SSD Connections 6
3.3 HDX-SSD Connected to XPS Power Supply 7
4 The Front Panel Display Interface 8
4.1 The Home Menu 8
4.2 The Browse Music Menu 9
4.3 The Find Music Menu 10
4.4 The Ripping Monitor Screen 10
4.5 The Current Playlist Screen 10
4.6 Playlists 11
4.7 The Quick Play Menu 12
4.8 The System Setup Menu 12
4.9 Handset Functions 16
8 Interface Menu Structure 22
9 Hard Disk Player Terminology 23
10 HDX-SSD Specifications 25
11 User Notes 25
12 Commercial Acknowledgements 26
Note: This manual is issue No. 3 and describes the operation of
HDX-SSD units running software release version 1.5a SP1. HDX­SSD units running earlier software will not operate fully in the manner described in this manual. The software running in an HDX-SSD is displayed in the System Status menu.
HDX-SSD Hard Disk Player Introduction
1 HDX-SSD Hard Disk Player Introduction
The Naim HDX-SSD hard disk player will completely change the way you access and listen to your music collection. While the HDX-SSD may look like a CD player and can play CDs conventionally, it is intended to operate in a fundamentally different way.
• Rather than reproducing the audio on a CD inserted in its transport, HDX-SSD
reads and stores the CD data on a network connected hard disk drive for replay at any later time. Network stored files can be either audio files ripped from CD or compatible audio files created by other means.
• The HDX-SSD operates as a UPnP™ server providing audio files to any UPnP™
compatible playback hardware connected on the same network.
• In addition to its conventional analogue or digital audio outputs, the HDX-SSD can
provide up to six NaimNet/StreamNet network streams for playback in multiple remote areas.
• When the HDX-SSD first reads the data from a CD, it automatically accesses
an internet music database and downloads the information held for that CD. The information can include title, tracks, artist, composer, genre and numerous additional details. This can then be used by the HDX-SSD to select or search for material and to build custom playlists. The CD cover artwork will also be downloaded if available and displayed by the user interface.
• The HDX-SSD is able to operate as a conventional CD player. A CD inserted in the
drawer can be played immediately with its audio routed to the analogue and digital audio outputs.
The mode of control and operation of your HDX-SSD will depend upon the type of system with which it is integrated. These different “user interfaces” are introduced in Section 1.1 while the touch screen controlled Front Panel Display Interface is described in detail in Section 4.
If the HDX-SSD is your first experience of a network connected product you may find it worthwhile to read the glossary in Section 9 before moving on to installation and operation.
1.1 HDX-SSD User Interfaces
Unlike a conventional item of hi-fi equipment, the HDX­SSD can be operated in a number of different ways using a variety of user interfaces. The user interface you use to control your HDX-SSD will depend on the type of system in which it is installed and the ancillary equipment available. The following short paragraphs and table describe each user interface.
1.1.1 The Front Panel Display Interface
The HDX-SSD is most conveniently operated via its Front Panel Display Interface using either the front panel touch screen or the remote handset.
Note: The Front Panel Display Interface can also be
configured to control any StreamNet compliant device connected to the network.
1.1.2 The External Display Interface
The HDX-SSD can be operated via its External Display
Interface using the supplied remote handset (or a
keyboard and/or mouse), in combination with an additional external display screen. The screen may be a monitor or TV with composite video, S-video or VGA input.
The External Display Interface is closely related to the Front Panel Display Interface and similarly provides access to HDX-SSD operational and setup features.
1.1.3 The NaimNet/StreamNet Touch Screen Interface
If the HDX-SSD is installed in a NaimNet home network, HDX-SSD network audio streams can be controlled from the NaimNet/StreamNet Interface. The NaimNet/ StreamNet Interface can be accessed from a StreamNet compliant touch screen or a web browser. The interface can also control any StreamNet compliant device.
Note: The NaimNet/StreamNet Interface is not covered in
this manual.
1
HDX-SSD Hard Disk Player Overview
1.1.4 The Web Browser Interface
If the HDX-SSD is installed in a home network the External Display and Front Panel Display interfaces can be duplicated by any Flash enabled web browser
To access the External Display Interface from a web browser, open the web browser and type the unique “name” of your HDX-SSD into the browser address field. The name is the last four characters of the MAC address (excluding the colon separators) printed on the rear panel preceded by NSHDX). A typical “name” would be NSHDX4567.
To access the Front Panel Display interface from a web browser add the suffix:
/index.html?movie=fp.swf to the HDX-SSD name. E.g. NSHDX89B5/index.html?movie=fp.swf
Note: Depending on your web browser you may need to
type “http://” immediately before the HDX-SSD name.
1.1.5 The Desktop Client
If the HDX-SSD is installed in a home network that includes a personal computer running Windows XP, Vista or 7, it can be operated via the Desktop Client Interface. The Desktop
Client application provides the most comprehensive
operational and search functionality. The Desktop Client is covered in a separate manual that can be downloaded from the Naim Audio web site at www.naimaudio.com.
Some setup, file management and maintenance facilities are only available via the Desktop Client.
1.1.6 iPod/iPhone App
The n-Serve app, available from the iTunes App Store, enables wireless touch screen control of HDX-SSD from an iPhone or iPod touch.
1.2 HDX-SSD Interface Options
Interface Control Display Notes
Front Panel Display Touch screen. Front Panel display. Enables control of both HDX-SSD local outputs in
Remote handset. stand-alone installations and network streams in network connected installations.
External Display Remote handset. TV or monitor with VGA, Controls local outputs only. Keyboard/mouse. S-video or composite input. USB/VGA touch screen. USB/VGA touch screen.
Web Browser Flash enabled web browser. Duplicates functionality of Front Panel and External Display Interfaces. Network connection required. Controls local outputs only.
Desktop Client Computer running Windows XP, Provides music database management and Windows Vista or Windows 7. advanced HDX-SSD setup functions. Can also control local outputs. Network connection required.
NaimNet/StreamNet StreamNet compliant network touch screen. Controls network streams only. Does not control local outputs. Network connection required.
n-Serve iPod/iPhone App iPhone or iPod touch Controls HDX-SSD local output only. Wireless network connection required.
Note: An internet connection is required for detailed CD data lookup. Without an internet connection, limited information is
available from a locally held database.
2
Installation - Getting Started

2 Getting Started

The HDX-SSD is a CD-ripping hard disk player and server. It incorporates no built-in storage but requires an external network attached storage disk drive (a NAS drive) to be connected and configured before it can be used. Configuring a NAS drive is described in Section 7 of this manual.
HDX-SSD must be connected to a network to stream music around the home, or to take advantage of many of its user interfaces. It must also be connected to the internet to retrieve album data and artwork from the internet, It is important that the network is working when HDX-SSD is connected and switched on.
HDX-SSD should be installed horizontally on a dedicated equipment stand intended for the purpose. Do not stand HDX-SSD directly on top of another item of equipment. HDX-SSD should be installed in its final location before connecting cables or switching on.
Locally connected audio amplifiers should not be switched on before HDX-SSD is switched on. The HDX-SSD power switch is located on the rear panel.
To begin installation first identify the rear panel network, audio output and power input sockets, and connect the appropriate cables.

2.1 Internet/Network Connections

Unitiserve-SSD requires a connection to network attached storage in order to operate, and an “always on” internet connection if its full capabilities are to be realised. It should be connected to the internet via an ethernet router/ modem with a built-in firewall
The network connection also enables HDX-SSD to communicate with other network devices, to be used in a NaimNet/StreamNet network audio system, and provides access to its alternative user interfaces.
The HDX-SSD is set up when originally shipped not to require any further network configuration but to connect to a network automatically (it uses DHCP by default). However, if your HDX-SSD has been previously used, its network configuration may have been altered leaving it unable to connect automatically. Contact your retailer, installer or Naim Audio directly if this appears to be the case.
2.1.1 Network Hardware
Wired network connection is strongly recommended for the most consistent and secure HDX-SSD operation.
Ethernet-over-mains hardware may be used and provides a simple and convenient method of home network connection. However, depending on mains wiring factors specific to each home environment, the presence of network data on the mains supply may compromise overall system sound quality. If any sound quality compromise is found to be unacceptable, dedicated network cabling should be installed.

2.2 Power Supply Upgrade

The HDX-SSD can be upgraded through the use of an external Naim XPS or CD555PS external power supply to power its analogue circuits.
If an external power supply is to be used, the link plug in the rear panel of the HDX-SSD should be removed and the power supply connected in its place using an SXPS Burndy cable. See Diagram 3.3.
THE SXPS BURNDY CABLE ONLY MUST BE USED TO CONNECT THE XPS OR 555PS POWER SUPPLIES.
Both the HDX-SSD and the external power supply must be switched off when the link plug is removed and the Burndy connections are made. Switch on the external power supply first followed by the HDX-SSD.

2.3 Audio Connections

Connect one or all of the analogue DIN (output 1) or
Phono (output 2) output sockets, or the Digital output
socket, to an appropriate audio system input. If using the analogue outputs use a Naim Hi-Line interconnect cable for best results.
Note: The output selector on the rear panel should be
switched to reflect the analogue output connections used.
2.3.1 Signal Ground
Switch the HDX-SSD’s rear panel Signal Ground switch (see paragraph 3.2.14) to the Chassis position unless the HDX­SSD is connected in a hi-fi system incorporating another earthed source component, or mains “hum” is audible through the loudspeakers. Contact your retailer, distributor or Naim for advice if necessary.
Note: All Naim CD players are earthed so the Signal
ground switch should be set to floating if one is connected in the system.
Note: “Connected” in this context means an analogue
audio signal cable that includes an earth connection.
3
Installation - Getting Started

2.4 Switch On

If the HDX-SSD’s network facilities are to be used ensure that it is connected to a working internet connection before switching it on and that all the necessary peripheral equipment is appropriately connected and configured.
Switch on the HDX-SSD using the rear panel power switch.
Note: If the HDX-SSD is to be switched on from shutdown
mode, the power switch must be switched off and on again. See Section 2.8 for more on shutdown mode.
After approximately one minute’s delay, the user interface
Home menu will appear on the front panel touch screen
(and any connected display). Navigate around the interface and select options by touching the screen or using the remote handset navigation ( and back keys.
Note: It is occasionally possible for the default remote
handset command set to conflict with other remote controlled equipment in the home. A conflict will be apparent if the handset appears to control an unintended device or if another handset appears to control the HDX­SSD. If a conflict occurs the HDX-SSD handset command set can be changed. While pointing the handset towards the HDX-SSD, press and hold both the page down and input keys while simultaneously pressing the 2 or 3 key to change the command set. Press the 1 key to return to the default command set.
3456), ok, home

2.5 External Screen Setup

If an external display is used, the HDX-SSD external display setup may need to be modified. Navigate, via the System menu, to the System Setup menu. Select and save the desired External Display Theme, External Display Aspect
Ratio, External Display Mode and TV System. Initially disable
the Screen Saver (found on System Setup page 1).
Note: The External Display Mode setting configures the
external display for use with either an external touch screen or a remote handset. In touch screen mode, four shortcut buttons are displayed on the right of the screen that correspond to the home, browse, find and back keys on the remote handset. The on screen shortcut buttons can only be accessed from the touch screen so are not shown in remote control mode.
Note: Once you have become used to the interface and
are familiar with its functions the screen saver can be re-enabled.

2.6 First Use

Before attempting to rip a CD you must ensure that the necessary Network Attached Storage (NAS) disk drive is appropriately configured, connected to the network, and switched on. Section 7 of this manual describes the use and configuration of external storage.
To rip a CD, insert the CD into the transport slot. The ripping process will begin automatically. When CD ripping is complete HDX-SSD will eject the CD automatically. See Section 6 for further information on ripping CDs.
Only CDs owned personally should be ripped. Ripping a borrowed CD may violate copyright law.
Note: Although the HDX-SSD contains a small internal music
database, to be able to identify a CD and download its associated data during the ripping process, it must be connected to a working internet connection.

2.7 Software Upgrade

Software upgrade CDs will occasionally be released for the HDX-SSD. New software is installed simply by inserting the upgrade CD in the drawer. The software upgrade process will commence automatically. As part of the upgrade process the HDX-SSD will eject the CD and re-boot. The front panel display may also go blank temporarily. The upgrade process is complete once the display returns to the Home Menu.
Note: Any specific instructions included with the upgrade
CD should be followed carefully.
Never switch off the HDX-SSD from the rear panel power switch or unplug it from the mains supply while a software upgrade process is underway.

2.8 Switching Off

Switching off the HDX-SSD from its rear panel power switch is not normally necessary unless it is to be un-installed. It can be put into shutdown mode by pressing the handset
shutdown key or pressing and holding the front panel shutdown button for one second. The HDX-SSD may take
up to one minute to enter shutdown mode during which time the shutdown button will flash. The shutdown button will remain lit when the HDX-SSD is in shutdown mode. Wait until the shutdown button stops flashing and remains lit before switching off the HDX-SSD from the rear panel mains switch.
Never switch off the HDX-SSD from the rear panel mains switch or unplug it from the mains supply unless it is in shutdown mode.
To switch the HDX-SSD back on from shutdown mode, the power switch must be switched off and on again.
2.9 Data Backup
We strongly advise that you protect your stored music by implementing a regular backup to a second NAS hard disk drive.
Backups should only be performed over the network and we recommend that weekly, automated time-stamped, differential backups are carried out.
4
Installation - Getting Started
The majority of commercially available NAS drives incorporate setup menus, accessed via a web browser, that enable regular automated backup of a specified target drive to be configured.
The automated backup setup procedure for the majority of NAS drives will be similar to the one described in the following steps.
Ensure that the backup NAS drive and HDX-SSD
•
Music Store NAS drive are on the same network and switched on. Read the backup NAS drive user instructions and make sure you understand its operation.
• From a computer connected to the network open
a web browser application and browse to the NAS backup drive setup menus. The network “name” or “address” of the NAS drive will be provided in its user documentation or on a label affixed to its case.
•
From the NAS drive setup menus, create a new
shared folder on the NAS drive called “UServe-SSD NAS Backup”.
•
Again from the NAS drive setup menus, create a new
“backup job”. Select a remote, time-stamp backup and type the HDX-SSD NAS drive network “name” or “address” (“192.168.0.5” for example) in the “host” text field. In the “path” field type “Music”. If login and password fields are provided leave them blank.
•
If a connection test facility is provided within the
setup menus, use it and wait for a positive result.
From the NAS drive setup menus, select the desired
•
backup format and schedule. We recommend selecting a weekly, time-stamped, differential backup. The initial backup may take a considerable time to complete.
Note: The backup process may reduce HDX-SSD response
speed while it is underway. It is best to schedule backups to run at times when the HDX-SSD is unlikely to be in use.
Note: A differential backup only records changes that
have occurred since the last backup.
Note: As well as using a NAS drive for backup it is also
possible to use an automatic backup application running on a network connected computer. This option however requires that the computer is left running permanently to ensure that scheduled backups are not missed.
5
Installation - Getting Connected

3 Getting Connected

The HDX-SSD carries a variety of connection sockets on its rear panel. These are illustrated and described in the following diagrams and paragraphs. The numeric legends on the rear panel diagram refer to the numbered paragraphs in Section 3.2.
3.1 HDX-SSD Rear Panel
power switch
mains input and fuse
3.2.2
keyboard
3.2.1
mouse
socket
socket
3.2.3
VGA
display
interface
3.2.4
serial interface
interface
sockets
3.2.5
USB
3.2 HDX-SSD Connections
3.2.1 Keyboard Socket
Optionally connect a PS2 format keyboard here to control the HDX-SSD in combination with an external display.
3.2.2 Mouse Socket
Optionally connect a PS2 format mouse here to control the HDX-SSD in combination with an external display.
3.2.3 VGA Interface
Optionally connect a VGA format screen here to display the HDX-SSD External Display Interface.
3.2.4 Serial Interface
For use if the HDX-SSD is to be integrated into an RS232 controlled environment.
3.2.5 USB Interface Sockets
USB control or audio source devices may be connected here. USB source devices can be made available across a network.
3.2.6 Network Socket
Connect to your network router here. The HDX-SSD requires a working internet connection.
3.2.7 S-video and Composite Video Sockets
Connect an S-video or composite video screen (television) here for display of the HDX-SSD External Display Interface.
3.2.8 IR Input Socket
Optionally connect an RC5 control signal here for local control of the HDX-SSD from an IR control repeater.
network
socket
3.2.6
S-video and composite video sockets
3.2.7
3.2.9 Coax and Optical Digital Audio Outputs
3.2.10 Power Supply Upgrade
3.2.11 Output Selector
3.2.12 DIN Analogue Output (output 1)
3.2.13 Phono Analogue Output (output 2)
3.2.14 Signal Ground
3.2.12
3.2.8
remote input socket
optical digital
audio outputs
S/PDIF digital audio for connection to an audio system digital input. These TosLink and BNC outputs duplicate the analogue outputs.
Enables the connection of an upgrade XPS or 555PS power supply. The link plug fitted must be removed. See Diagram 3.3.
THE SXPS BURNDY CABLE ONLY MUST BE USED TO CONNECT THE XPS OR 555PS POWER SUPPLIES.
Note: Both the HDX-SSD and upgrade power supply must
be switched off when the link plug is removed and cable connections are made.
Selects output 1 (DIN), output 2 (phono) or both.
Analogue output from the HDX-SSD for connection to a local audio system. Use this option if connecting to a Naim system.
Analogue output from the HDX-SSD for connection to a local audio system. Use the DIN option in preference to the Phono option if connecting to a Naim system.
Optionally disconnects and “floats” the analogue signal ground from the chassis earth. Select chassis unless the HDX-SSD is installed in a hi-fi system incorporating another mains earthed source component or mains “hum” is audible from the loudspeakers.
3.2.10
power supply
upgrade socket
(link plug tted)
coax and
3.2.9
phono analogue
audio output
(output 2)
3.2.13
output selection
3.2.11
DIN
analogue
audio
output
(output 1)
signal ground
3.2.14
6
Installation - Getting Connected
3.3 HDX-SSD and XPS Power Supply
power switch
THE HDX-SSD REQUIRES MAINS POWER AT ALL TIMES - WITH
mains input and fuse
mains input and fuse
OR WITHOUT AN EXTERNAL POWER SUPPLY.
THE SXPS BURNDY CABLE ONLY MUST BE USED TO CONNECT THE XPS OR 555PS POWER SUPPLIES.
Cable direction marker
SXPS Burndy Cable
7
Loading...
+ 19 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use