Nady PSW18A User Guide

Features, Instr uctions

Pantone 185 Red/Black/Cool Gray 40%

BLACK

& Technical Data

PSW-18A

Powered S u b w o o f e r

Powered subwoofer with superior performance, state­of-the-art versatile design, unprecedented affordability
— perfect for all small venue applications.

Congratulations!

You have just purchased one of the finest powered subwoofers on
the market today. The PSW-18A was developed using the expertise
of professional sound engineers and working musicians. You will find
your new NADY AUDIO powered subwoofer has superior performance
and greater flexibility than any other powered subwoofer in its price
range.

We recommend that you read this instruction sheet carefully to get the
most out of your new unit. Thanks for selecting NADY AUDIO and the
PSW-18A as your choice in powered subwoofers.

F E A T U R E S

The PSW-18A self-powered subwoofer punches a wallop of sound, power, and fury with over 1100 Watts!! You find the frequency to
shake the floors with the sub set to the desired roll-off point with its fully adjustable low-pass filter. Boasting a 1200W 18” cone driver,
and capable of 123dB of sound pressure level, the thump has never bumped so hard!

• Balanced XLR and 1/4” parallel I/O for easy thru-put plus dual
RCA inputs

• Master Volume control and adjustable Low Pass filter from 60Hz
to 260Hz with steep roll-off for maximum punch

• “Soft start” power on/off switch with Power and Clipping LED
indicators

• Sturdy plywood cabinet with durable carpet covering, steel grill,
protective corners, and 1 3/8” (35mm) polemount receptacle

W A R N I N G S

When using this speaker, basic precautions should always be taken, including the following:

• Read all instructions before using the product.

• This product may be capable of producing sound levels that could
cause permanent hearing loss. Do not operate for a long period
of time at a high volume level or at a level that is uncomfortable. If
you experience any hearing loss or ringing in the ears, you should
consult an audiologist.

• To avoid damage to the drivers, never overload the speaker.

• To avoid the risk of fire, do not ever expose the speaker to a source
of naked flames. Also, it should be located away from heat sources
such as radiators, heat vents, or other devices (including amplifiers)
that produce heat.

• The product should be positioned so that proper ventilation is
maintained.

• This speaker is designed for indoor use only. Do not expose to
weather or high humidity, rain, etc.

• Care should be taken so that objects do not fall into, and liquids

• Bridge mode power amp for highest power with lowest distortion,
output relay safety protection, ultra-efficient cooling, low-noise
exhaust fan, and AC fuse

• Dual mounting pole adapters

• Optional SMP-3 speaker mounting pole available

IMPORTANT SAFETY INSTRUCTIONS

are not spilled through, the enclosure’s openings. Do not place
containers of liquids on the speaker.

• Don’t place any heavy appliance or object (>130lbs/60kg) on the

speaker enclosure.

• This unit is to be installed by qualified personnel only.

• This speaker is only to be used with power amplifiers complying

with the safety requirement of EN or IEC60065.

• This product should be serviced by qualified service personnel if:

A. Objects have fallen into, or liquid has been spilled onto the

product.
B. The product has been exposed to rain.
C. The product does not appear to operate normally or exhibits
a marked change in performance.
D. The product has been dropped, or the enclosure damaged.

• Do not attempt to service this unit. All servicing should be referred
to qualified service personnel.

FF

O P E R A T I O N

(1) Power Switch — Use this switch to power the unit
ON or OFF.
(2) AC Power Cord IEC Connector — This standard
IEC power cord receptacle features a built-in fuse
holder.

(3) Power ON LED
(4) Clipping LED — This LED indicator turns red when

the output signal is 3dB below clipping. It is acceptable
if the red LED lights very occasionally. If the red LED
lights more than occasionally, you should turn down
the volume to avoid audible distortion and damage to
the speaker.

Note: Speakers damaged due to hard clipping are
not covered under warranty.

(5) AC Voltage Selector Switch — Before plugging in
the power cord, check to see that the unit is set for the
proper voltage for your area: ~115V (60Hz) or ~230V
(50Hz).
(6) Line Inputs — These Balanced XLR and 1/4’
TRS jacks accept Line Level balanced or unbalanced
signals. These inputs can be used as outputs also for
easy thru-put when daisy-chaining powered speakers.
(7) RCA Inputs — These dual RCA low line level
inputs can be used singly or together, as they are
mono’d together to ensure subwoofer frequencies from
both Left and Right signals are accounted for.
(8) Low Pass Control — This sets the upper band­width frequency of the low pass filter from 60Hz to
260Hz. Adjust this control for the desired punch of the
subwoofer depending on the audio desired to fit the
music and environment.
(9) Volume Control — This adjusts the subwoofer
volume level. This can be set to maximum if the user
prefers to control the volume at the preceding unit.
Make sure not to overpower your speaker by noting
the appropriate level at the mixing board fader con­trol and LED bargraph to avoid clipping. Over-driven
speakers due to improper use are not covered under
warranty.

TECHNICAL DATA

(5)

(1)

(6)

(2)

7

(3)

(8)

(9)

(4)

CAUTION — REAR PANEL GETS VERY HOT!

1. AVOID CONTACT WITH SKIN.

2. KEEP PANEL AWAY FROM FLAMMABLE OBJECTS.

3. FOR MAXIMUM COOLING, VENTILLATION, AND EFFICIENCY, DO NOT PO­SITION SUBWOOFER REAR PANEL AGAINST WALLS OR OTHER OBJECTS.

S P E C I F I C A T I O N S

Amplifier Power: 1120W Peak (560W RMS)
Subwoofer cabinet: Front-loaded, Vented, Plywood
Max SPL: 123dB @1M
18” Speaker: Magnet: 125 oz., 4”dia. voice coil
Speaker Power Handling: 1200W Peak (600W RMS)
Speaker Impedance: 8 ohm
Frequency Response: 20Hz to 60~260Hz (adjustable)
Balanced XLR & 1⁄4” Inputs
Impedance: 20K ohm
Sensitivity: 500mV RMS (max output w/controls at max)

S E R V I C E

(U.S.) Should your NADY AUDIO product require service, please contact the Nady Service Department via telephone at [phone]
or e-mail at [e-mail].

(International) For service, please contact the NADY AUDIO distributor in your country through the dealer from whom you purchased
this product.

FOR YOUR NADY AUDIO PRODUCT

NADY S YST EMS, INC . • 67 01 SHELLMO UND S TREET, EME RYVILLE, CA 9460 8
Tel: [phone] • Fax : [phone] • www.na dy.co m

Unbalanced RCA Input
Impedance: 10K ohm
Sensitivity: 250mV RMS (max output w/controls at max)
Protection: Fan cooling, short circuit protection, speaker DC protec-

tion circuits, clipping indicator, power ON/OFF relays for anti-thump
circuit, AC fuse

Voltage Selector: 115VAC/60Hz or 230VAC /50Hz
Fuse: 5x20mm glass tube F.B. 8A 250V @ 115VAC

4A 250V @ 230VAC

Dimensions (HxWxD): 25.4”x 19.7”x 22” (645x500x560mm)
Weight: 194 lbs (88kg)