NAD Electronics M25 Owner's Manual

®

M25

Seven Channel Power Amplifier

ENGLISH

FRANÇAISDEUTSCH

Owner’s Manual

Manuel d’Installation
Bedienungsanleitung
Gebruikershandleiding
Manual del Usuario
Manuale delle Istruzioni
Manual do Proprietário
Bruksanvisning

NEDERLANDS

ESPAÑOLITALIANO

PORTUGUÊS

SVENSKA

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

• Save these instructions for later use.

• Follow all warnings and instructions marked on the audio equipment.

1 Read instructions - All the safety and operating instructions should be read before the product is operated.
2 Retain instructions - The safety and operating instructions should be retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be followed.
5 Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.
6 Attachments - Do not use attachments not recommended by the product manufacturer as they may cause
hazards.
7 Water and Moisture - Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub; in a wet basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9 A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
10 Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from overheating, and these openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11 Power Sources - This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your home, consult your product dealer or local power
company.

• Main Power Disconnect; When the power switch is in the Off position, the amplifier is not completely
disconnected from the main power. The primary method of isolating the amplifier from the mains supply is to
disconnect the mains plug. Ensure that the mains plug remains accessible at all times. When installing the
product, ensure that the plug is easily accessible.

• Non-use Period; Unplug the AC power cord from the AC outlet if the unit will not be used for a long period
of time such as several months or more.

• CLASS 1 Products; The M25 shall be connected to a MAINS socket outlet with a protective earthing connection.

12 Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
13 Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER

• This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected

to the grounding system of the building, as close to the point of cable entry as practical.

14 Lightning - For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and power-line surges.
15 Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with
them might be fatal.
16 Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17 Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.

WARNING

18 Transportation - Transport the amplifier in both inner and outer shipping containers. Do not transport the
amplifier using one shipping container; to do so may result in damage to either the amplifier or personnel.

2

IMPORTANT SAFETY INSTRUCTIONS

19 Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:

a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by

the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to its normal operation.

e) If the product has been dropped or damaged in any way.
f) when the product exhibits a distinct change in performance-this indicates a need for service.

20 Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by

the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or
other hazards.
21 Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22 Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE LIGHTNING
FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE
PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF
IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE
APPLIANCE

CAUTION

Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user’s authority
to operate this equipment.

CAUTION REGARDING PLACEMENT

To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal
to, or greater than, shown below.
Left and Right Panels : 10 cm
Rear Panel : 10 cm
Top Panel : 50 cm

IMPORTANT INFORMATION FOR UK CUSTOMERS

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable
is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. If, nonetheless,
the mains plug is cut off, REMOVE THE FUSE and dispose of the PLUG immediately, to avoid possible shock hazard by inadvertent
connection to the mains supply. If this product is not provided with a mains plug, or one has to be fitted, then follow the instructions
given below:

IMPORTANT

DO NOT make any connection to the larger terminal which is marked with the letter ‘E’ or by the safety
earth symbol or coloured GREEN or GREEN AND YELLOW.
The wires in the mains lead on this product are coloured in accordance with the following code:

BLUE - NEUTRAL

BROWN - LIVE
As these colours may not correspond with the coloured markings identifiying the terminals in your plug, proceed as follows:
The BLUE wire must be connected to the terminal marked with the letter ‘N’ or coloured BLACK.
The BROWN wire must be connected to the terminal marked with the letter ‘L’ or coloured RED
When replacing the fuse, only a correctly rated and approved type should be used, and be sure

to re-fit the fuse cover.

IF IN DOUBT CONSULT A COMPETENT ELECTRICIAN

This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE 89/68/EEC and 73/23/EEC

NOTES ON ENVIRONMENTAL PROTECTION

At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection
point for the recycling of electrical and electronic equipment. The symbol on the product, user's manual and packaging, point this out.
The materials can be reused in accordance with their markings. Through re-use, recycling of raw materials, or other forms of recycling
of old products, you are making an important contribution to the protection of our environment.
Your local administrative office can advise you of the responsible waste disposal point.

Model No. :________________________Serial No. :_________________

3

FRONT PANEL CONTROLS

PANEL CONNECTIONS/CONTROLS

4

FIGURE 1

Spade

Wire

FIGURE 2

Pin

3

ABOUT THE M25

THE DESIGN

ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO

PORTUGUÊS

SVENSKA

Designed specifically for home theatre and custom installation set-ups,
the NAD M25 Power Amplifier delivers uncompromising performance.
It combines supreme reliability, flexibility, and performance with
outstanding value. Flexibility has always been an important part of
NAD components. Such flexibility is particularly important in home
theatre and other multi-channel systems. That’s because it is common
for a multi-channel system to incorporate different brands and models
of loudspeakers. Often these speakers have different levels of
efficiency. The individual input level controls for the seven channels of
the NAD M25 make it easy to compensate for such differences in
efficiency, and achieve the ideal system balance. Ample dynamic
headroom of the M25 ensures that the very wide dynamic range of
modern cinema soundtracks and digital music sources will be
preserved. In addition, the M25 will handle low impedance speakers
with ease.

The M25 incorporates NAD’s unique Soft-Clipping circuitry in all seven
channels. Any amplifier can be overdriven if it is played too loud,
exceeding the maximum output power. Under such circumstances,
amplifiers produce extreme high levels of distortion which, besides
sounding very unpleasant, can damage your loudspeakers. The Soft
Clipping circuit suppresses such distortion and minimizes the risk of
damage to speakers. This is particularly important with movie
soundtracks which often contain very dynamic outbursts in which,
unlike music, it is difficult to hear this potentially damaging distortion.
The Soft Clipping LED on the front panel illuminates when the Soft
Clipping circuit is engaged. Soft Clipping can be defeated with a rear
panel switch.

The 12V trigger connection on the back panel allows the amplifier to
be switched from On to Stand-by and vice-versa remotely. This way,
the M25 can be part of a system which can be turned on and off with
a single command, easing operation. The 12V trigger also allows the
amplifier to be installed in places not in easy reach.

The NAD M25 houses seven individual amplifiers, each on separate
circuit board. Each amplifier channel acts as a “mono block” within
the chassis. Each input connector, and set of loudspeaker output
terminals, is directly connected to that channel’s circuit board. This
design eliminates extra wiring and keeps signal paths short.
Furthermore, this modular design increases reliability and thermal
efficiency. The input circuit uses a totally new dual differential input
topology that operates in true Class-A mode. The special Holmgren™
toroidal transformer has less hum and magnetic leakage than
conventional toroidal transformers, but retains the usual benefits of
high efficiency and high power-to-weight ratio.

Ruggedness and reliability are critical in custom-installed systems. The
M25 uses a combination of fuses and non-intrusive electronic
protection. This provides highly effective protection that does not
effect audio performance. Each channel is protected against excess
temperature, DC fault and loudspeaker short-circuit. The M25’s
inherently conservative, high-voltage/high-current output stage has
been designed for years of trouble-free service.

NAD was the first company to introduce a THX® Certified power
amplifier. In that tradition, the M25 easily passes THX Ltd.s' stringent
THX® performance requirements. As a result the NAD M25 will
handle the most demanding signals with ease, and yet preserve every
subtle audio detail in the most demanding THX® Ultra2™ Surround
systems. THX and Ultra2 are trademarks or registered trademarks of
THX Ltd. All rights reserved.

POWERDRIVE

To meet the diverse requirements of high current drive and high
dynamic power, our patented PowerDrive amplifier circuit will build
further on our reputation for amazingly effective power. By adding a
second high-voltage rail to our well regulated high-current power
supply, we get an "overdrive" that can nearly double the continuous
power on a short term dynamic power basis. This is a further
development and refinement of our renowned Power Envelope circuit,
utilized by NAD in the 80's and 90's. PowerDrive differs from Power
Envelope in that it offers greater amplifier stability and low impedance
drive capability, resulting in less distortion when driving real speakers
with real program material

6

INSTALLATION PRECAUTIONS

TRANSPORTATION

WARNING - To reduce the risk of fire or electrical shock, do not
expose the amplifier to rain or moisture.

CAUTION - For units factory-set at 115 volts AC match the wide blade
of the power plug to the wide slot of the power outlet, to prevent
electrical shock. Be sure the plug is completely inserted into the
receptacle.
Turn off all the components in the system whenever connecting or
disconnecting any audio signal wiring. Once all signal connections have
been completed, turn down all the system’s main volume control before
turning the system components on. Then increase the volume control
setting carefully to avoid damage to the system components.

NOTES ON INSTALLATION LOCATION

Read and follow all the safety instructions on the first page of this
manual. To prevent a fire or shock hazard, do not place the amplifier
where it will be exposed to any water or moisture. If liquid accidentally
gets into the amplifier, immediately unplug the AC power cord. Do not
operate the amplifier again until it has been examined by a service
technician.

The amplifier generates a moderate amount of heat, requiring
ventilation. Do not obstruct the air outlet grilles on the top or bottom
covers. There should be at least 3 inches (7.5 cm) of clearance above
the amplifier and 1 inch (2.5 cm) to the sides. Do not place the
amplifier in an enclosed area, such as in a bookcase or in a cabinet,
unless it is very well ventilated. Be sure there is adequate room behind
the amplifier for signal input and speaker output connections. If you
want to locate the amplifier on a carpeted floor, place a board under
it in order to prevent it from sinking into the carpet, blocking the air
inlets on the bottom. Do not place the amplifier where it will be
exposed to direct sun light for prolonged periods of time.
This unit may be installed on any sturdy, level surface.

]NOTES: The amplifier’s weight must always rest on its bottom feet.

Never put the amp down on its rear panel, with its front panel
facing up. Doing so risks damage to the input/output connectors.

Transport - Transport the amplifier in both inner and outer shipping
containers. Do not transport the apparatus using one shipping
container; to do so may result in damage to either the apparatus or
personnel.

SAVE ALL THE PACKAGING

Please save both boxes and all of the packaging in which your M25
arrived. Should you move or otherwise need to transport your amplifier,
this is by far the safest set of containers in which to do so. We’ve seen
too many otherwise perfect components damaged in transit for lack of
proper shipping cartons, so please: Save both inner and outer boxes!

REAR PANEL CONNECTIONS/CONTROLS

1. IEC POWER SOCKET

Connect to the supplied IEC-standard removable AC power cord
before connecting the AC power cord to the wall socket.

NOTE: Before connecting the AC-power cord to a live wall socket

insure that all inputs/outputs are connected first. Always
disconnect the AC power cord plug from the live wall socket first,
before disconnecting any cable from the M25 amplifier. If you must
use an extension cord, select a heavy-duty cord of the type used for
large electrical appliances, such as an air conditioner AC-extension
cord (16 AWG). We strongly recommend that you not connect the
amplifier’s mains cable to the accessory AC outlets on a
preamplifier. Such convenience outlets are not designed to supply
the high-power levels that the NAD M-series amplifier requires.

2. INPUTS

Each of the seven independent power amplifiers within the M25 has
its own signal input connector. Before making any connections to the
amplifier, make sure the POWER is switched OFF. [See figure 1]

Connect the signal cables from the preamplifier, surround sound
decoder, or other signal source to these inputs. For optimum heat
dissipation in an AV surround system, we recommend you allocate the
audio channels to the inputs as follows:

ENGLISHFRANÇAISDEUTSCHESPAÑOLITALIANO

The power transformer in the M25 generates a magnetic hum field
of moderate strength. Turntables (especially those with a moving­coil pickup cartridge) should not be located near the amplifier.
Magnetic media, such as audio or video tapes and computer
diskettes, should not be stored near the amplifier.

Channel 1 = Front Left speaker
Channel 2 = Surround Left speaker
Channel 3 = Surround Back Left speaker
Channel 4 = Center speaker
Channel 5 = Surround Back Right speaker
Channel 6 = Surround Right speaker
Channel 7 = Front Right speaker

PORTUGUÊS

SVENSKA

7

ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO

3. INPUT LEVEL CONTROLS

The amplifier is equipped with separate input level controls for each
channel. Before turning on the M25 for the first time, make sure all
level controls are in their normal full-clockwise position. With the
input levels set to the maximum position, the gain is exactly
conforming to THX Ultra

Under some circumstances, other settings may be useful for:

• Level-matching - In systems that incorporate speakers of varying
efficiencies, it may be necessary to reduce the settings of some
controls to achieve proper channel-to-channel balance.

• Extended volume-control range - Many stereo systems have so
much voltage gain that the speakers (or your ears) are over-driven
at any volume-control setting higher than 11 or 12 o’clock position
of the volume control. As a result you can use only the lower half
of the volume control’s range, where adjustments are imprecise
and channel-balance errors tend to be greater. If all input level
controls are reduced, you can turn up your preamplifier’s volume
control, making effective use of most of its range. (Suggestion:
Adjust the input level controls so that your preferred maximum
sound levels occur at about 2 or 3 o’clock on the volume control.)
As an added benefit, this procedure suppresses any noise produced
by the preamp’s high-level circuitry (e.g. any residual hum or hiss
that does not go away when the Volume is turned down).

™

standards.

2

5. AUTO TRIGGER ON/OFF

Set the Auto Trigger switch to the ON position to activate the 12V­trigger. By connecting the 12V-trigger, the M25 can be remotely
switched to On and Standby and vice-versa. When set to the Off
position, the 12V-trigger input is not active.

NOTE: With the Auto Trigger switch set to the ON position and the

12V-trigger input connected, the M25 will switch from Off to
Stand-by when the Power Switch on the front panel is pressed. For
normal operation, ensure the switch is in the OFF position or that
the 12V-trigger input socket is not connected.

6. 12V-TRIGGER INPUT

For external Power on/Stand-by switching, connect the 12V-trigger
output of a source component to this DC input jack. The center pin is
the live or + connection, the outer sleeve of the input jack is the 12V­trigger - or ground connection.

NOTES: The M25’s 12V-trigger will work within a range of 6 to 15 V

DC level and typically draws less than 10mA of current. Check the
specifications of the 12V-trigger source to ensure it is compatible
with the M25’s 12V-trigger input. Do not exceed the
recommended voltage as this may cause damage to the M25.

PORTUGUÊS

SVENSKA

4. SPEAKER CONNECTIONS

This amplifier is equipped with special high-current binding-post
speaker terminals. Connect the loudspeakers with heavy-duty (16­gauge or thicker) braided wire. Connections may be made in any of
three ways. [See Figure 2.]

• Strip off a half-inch (1 cm) of insulation from each speaker wire. In
each conductor, twist the thin strands of wire together. Unscrew
the knob, insert the bare wire into the opening at the base of the
binding post, and tighten the knob until it grasps the wire securely.
Check to be sure that there are no loose strands of wire touching
the chassis or an adjacent terminal.

• Spade lugs. Unscrew the knob, insert the U-shaped spade lug
behind the bushing, and tighten the knob until the spade lug is
secured.

• Install banana plugs on your speaker wires, and plug them into the
end of each binding post.

NOTE: Speakers must operate in phase with each other in order to

produce a proper stereo image and to reinforce rather than cancel
each other’s output at low frequencies. When connecting speakers,
take care that the red (positive) terminal on each loudspeaker is
connected to the corresponding terminal marked red (positive) on
the amplifier.

7. SOFT CLIPPING

When an amplifier is driven beyond its specified power output it
normally produces “hard clipping” or distortion of the signal. Such
hard clipping, in addition to sounding unpleasant, can damage the
speakers in the system. The NAD Soft Clipping circuit gently limits the
output waveform, minimizing audible distortion and reducing the
change of speaker damage when the amplifier is overdriven. We
recommend that the Soft Clipping switch on the back panel of the
M25 be left in the ON position when system is being operated at levels
that might exceed the amplifier’s power capacity. The LED on the front
panel indicates if Soft Clipping has been engaged.

8. FUSE HOLDER

There is a fuse holder nearby or next to the AC-line cord. In the
unlikely event a fuse may need to be replaced, unplug the line cord
from the wall. Then remove all connections from the amplifier. Only
replace the fuse with the same type, size, and specification.

9. GROUND CONNECTOR

The M25 is provided with a GROUND terminal on the rear panel. This
terminal is connected directly to the chassis of the M25. In the event
of radio hum or radio interference, this terminal can be connected to
a ‘true earth’ such as a copper plated rod driven several feet into the
ground.

8

FRONT PANEL CONTROLS

1. POWER SWITCH/STANDBY LED

Press this button to switch the amplifier on or off. The Power LED
located just above the power button and Protection LEDs (see
Protection LED below) will light up. After a few seconds, the
Protection LEDs will switch from red to blue, indicating that the
amplifier is ready for use.

The M25 can also be remotely switched from Standby to On and vice­versa using the 12V-trigger input on the back panel. When the M25 is
in the Standby mode, the Standby LED will be amber indicating the
Standby mode. For the 12V-trigger input to work, the M25 must first
be turned on by means of the front panel Power Switch, and the
switch must be left in this position. Using the 12V-trigger source
component, switch its 12V-trigger output to on and off. The M25's
trigger input will now follow the source component's 12V-trigger
output. Ensure that the Auto Trigger switch on the back panel is in the
ON position and that the 12V-trigger input is connected properly.

2. PROTECTION LED

The Protection LEDs turn red for about 3 seconds, every time the
amplifier is switched on. After a few seconds they will turn blue and
the amplifier is ready for operation.

These LEDs turn red when one or more of the internal seven amplifiers
go into protect mode, but the other amplifiers will continue to
function as shown by their blue LEDs so it is likely you will still hear
sound.

ENGLISHFRANÇAISDEUTSCHESPAÑOLITALIANO

When the amplifier is switched off from normal operation by means of
the front panel power switch, or to Standby via the rear panel trigger
source, the Protection LEDs will light up red and will fade out in a
couple of seconds..

NOTE: If you see a Protection LED turn red, turn off the amplifier

immediately using the front panel Power Switch. Check if all speaker
wires are connected correctly and that none of the wires are
damaged, causing a short circuit. Another cause may be excessive
heat build-up inside the amplifier. Make sure there is adequate
ventilation around the amplifier and that none of its ventilation slots,
top or bottom, are blocked. After the amplifier has cooled down it
will function normally again.

In case one or more of the Protection LEDs remains red despite the
checks mentioned above, turn the amplifier off by means of the front
panel Power Switch and consult your NAD dealer.

3. SOFT CLIPPING LIGHT

When the Soft Clipping circuit of the M25 is activated the indicator
LED on the front panel will light.

PORTUGUÊS

SVENSKA

9

TROUBLESHOOTING

ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO

PROBLEM

NO SOUND

NO SOUND ON ONE CHANNEL

NO SOUND ON SURROUND CHANNELS

NO SOUND ON CENTER CHANNEL

WEAK BASS/ DIFFUSE STEREO IMAGE

• Power AC lead unplugged or power not
switched on

• Speaker not properly connected or damaged.

• Input lead disconnected or damaged

• No surround mode selected

• Mono sound source

• Speakers not properly connected

• Surround volume level too low

• Speaker not connected properly

• Center volume level set too low

• Speakers wired out of phase

CAUSE

SPECIFICATIONS

AMPLIFIER SECTION

CONTINUOUS AVERAGE POWER OUTPUT >160 W (22.0 dBW)
INTO 8 OHMS OR 4 OHMS

(Minimum power per channel, 20 Hz - 20 kHz, all seven channels driven, with no more than rated distortion)

Rated Distortion <0.03%
(THD 20 Hz - 20 kHz)
Clipping power >180 W

(Maximum continuous power per channel, all seven channels driven)

SOLUTION

• Check if AC lead is plugged in and power
switched on

• Check connections and speakers

• Check leads and connections

• Select a Surround Mode

• Test system with Stereo or Dolby Surround
material

• Check speakers and connections

• Increase surround volume level

• Check speaker and connection

• Increase center volume level

• Check connections to all speakers in the system

PORTUGUÊS

SVENSKA

IHF DYNAMIC POWER

(Maximum short term power per channel)
8 ohms: > 220 W (23.4 dBW)
4 ohms: >
2 ohms: >

385 W (25.9 dBW)

485 W (26.9 dBW)
Damping factor > 180
(Reference 8 ohms at 50Hz)
Input Impedance R = 1 M Ω

C = 180 pF
Input sensitivity (for rated output into 8 ohms) 1250mV+/-50mV
Voltage gain 29 dB
Frequency response 20 Hz - 20 kHz ±0.2 dB

- 3dB at 3 Hz and 70 kHz

Signal / Noise ratio, A-weighted >96 dB ref. 1 W

>118 dB ref. 160W

DIMENSIONS AND WEIGHTS

Net Weight 96.3Ib (43.7kg)
Shipping Weight 115 Ib (52kg)
Dimension (W H D) Net 17.2 x 7.9 x 18.4”(435 x 200 x 466mm)

Gross* 17.2 x 8.5 x 19.5”(435 x 215 x 495mm)

*Gross dimensions include feet, volume knob, power button and extended speaker termianls.
Specifications are subject to change without notice. For updated documentation and features please log onto

www

.nadelectronics.com for the latest information about your M25.

10

www.NADelectronics.com

©2006 NAD ELECTRONICS INTERNATIONAL

A DIVISION OF LENBROOK INDUSTRIES LIMITED

All rights reserved. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International

M25 Manual 01/06 Printed in China