Nacon RC-300 Installation Manual
RC-300
RACING WHEEL STAND
BB5123
Made in China
396 Rue de la Voyette, CRT2 - Fretin,
CS90414, 59814 LESQUIN Cedex
RACING WHEEL STAND
SUPPORT DE VOLANT DE COURSE
LENKRADGESTELL
RACESTUURSTANDAARD
SOPORTE DE VOLANTE
SUPPORTO PER VOLANTE DA CORSA
SUPORTE DE VOLANTE
1
2
1
2
1
3
5
7
2
6
8
1
2
3
4
6x12 6x16 6x20
4mm
10mm
20mm 30mm M6
X8 X4 X4
X4 X12 X4
6X12
9
11
13
10
12
EN
na
RC-300
Thank you for purchasing the NACON RC-300 Racing Wheel Stand.
This product has been designed to enhance your video gaming experience.
Please keep this instruction manual for future reference.
If you require any assistance or help please contact the Helpline.
WARRANTY
This product bearing the NACON trademark, is guaranteed by the
manufacturer for a period of 2 years from the date of purchase, and will,
during this period be replaced with the same or a similar model, at our option,
free of charge, if there is a defect due to faulty material, or workmanship.
This guarantee does not cover defects arising from accidental damage,
misuse or wear and tear, and is available only to the original purchaser of
the product. This does not aect your statutory rights. Please keep the
proof of purchase receipt for any future claim. The original packaging must
be kept for all distance purchases (mail order & Internet).
PACKAGE CONTENTS
1 x Installation guide
1 x Foldable frame
Bag 1
4x Feet
1x Wheel plate with screws and nuts
1x Spanner
1x Allen screw
2x Knurled screw
2x 13mm nut
5x velcro cable holders
Bag 2
1 x Gear shift plate
1 x Gear shift plate bracket
2 x Screws 8 x 35mm
2 x Screws 6 x 12mm
2 x Washers
1 x Allen key
Bag 3
4 x Screws 6x12mm
12 x Screws 6x16mm
4 x Screws 6x20mm
8 x Washers 20mm
4 x Washers 30mm
4 x Nuts M6
1 x Allen key 4mm
1 x Spanner 10mm
ASSEMBLY
We recommend to assemble the RC-300 Racing Wheel Stand with the help
of a second person, as assistance may be required.
1. Loosen the knurled screws which hold the foot plate in position.
2. Unfold the frame and ap the foot plate downwards to the desired angle.
Tighten the foot plate, using the knurled screws again.
3. Attach the four feet to the bottom of the frame by screwing them into the
prepared holes.
4. Extend the wheel support stand until it reaches the desired height. Lock
it into position by tightening the two knurled screws.
NOTICE: The maximum height is marked by two square holes on the tube.
To ensure a stable wheel support, do not extend the frame beyond these
points.
5. Remove the screws from the wheel plate.
(Recommended) For easier assembly, we suggest to mount your wheel to
the plate, before attaching the plate to the frame. Finally attach the wheel
plate to the frame, using the same screws again.
6. Loose the screw on the back of the plate, if you need to adjust the angle
of the wheel.
7. (Optional) If you want to use it, attach the gear shift plate bracket to the
frame on either the left or right hand position using the 2x 8x35mm screws
and the two nuts.
8. (Optional) Then attach the gear shift plate with the 2x 6x12mm screws.
9. Place the frame on a at surface and make sure it is stable before using it.
Your racing frame is ready for its rst test drive!
MOUNTING OF RACING WHEELS
The wheel plate has been prepared with holes which t the majority of racing
wheels in the market. For mounting your wheel use the 6x16mm screws
which were supplied with your NACON RC-300 Racing Wheel Stand.
MOUNTING OF PEDAL SETS
The foot plate features several slots to which the majority of pedal sets in
the market can be attached by using the 6x16mm screws and washers.
IMPORTANT SAFEGUARDS & PRECAUTIONS
1. This product is for indoor use only. Never expose to wet weather
conditions.
2. Do not expose the unit to splashing, dripping, rain or moisture. Do
not immerse in liquid.
3. Do not expose to dust, high humidity, high temperatures or
mechanical shock.
4. Do not use if the equipment is damaged.
5. For cleaning, use a soft, clean, damp cloth only.
6. This device is not designed to be used by anyone (including children)
with impaired physical, sensory or mental capacity, or by anyone without
appropriate experience or knowledge unless they have received prior
guidance or instructions related to the use of this device from someone
who is responsible for their safety. Children should be supervised to
ensure that they do not play with the device.
7. Please keep all plastic bags out of the reach of babies and small
children.
8. Ensure that the frame is used on a at surface and is stable, before
use.
STORAGE
When you’re not using the NACON RC-300 Racing Wheel Stand, you
can remove the wheel and fold it for easy storage after loosening the two
knurled screws which hold the foot plate.
NOTICE: The frame will not fold completely with the wheel plate stand
completely retracted. You will need to slightly extend it. You may also wish
to unmount the gear shift support, when the frame is stowed away.
CUSTOMER SUPPORT
For UK support contact: support@nacongaming.com
Loading...