myWall GHYZ1011 Installation & Assembly

WORK 3

INSTALLATON GUIDE

Recommended Additional Items:

Level
Tape measure
Stud finder
Drill
Pencil
Wall mounting hardware

WORK 3

WARNING:

Prior to mounting french cleat onto wall, check for proper mounting anchors to use.
(drywall, metal studs, wood studs, or concrete block will all need different hardware)

WARNING:

Recommended use of side locking plate on walls after installation of each individual
panel (this ensures the safety of panel attaching securely to french cleat)

2 Folder
Holders

(includes 4 ­locking pins)

130mm Pin

(Includes 4)

STEP

2 Small Paper Clips

(includes 2 - locking pin)

1

Unpack boxes

(Ensure all parts are included for your wall installation)

French Mounting Cleat

(mounting hardware
NOT included)

Locking Plate

(includes 2 screws)

4 Shelves

(includes 10 pins)

Desk

(includes 5 pins)

Wood Pin

(Includes 4)

2 End-caps

(4 screws supplied)

myWall Panel

Magnetic Whiteboard

(includes 4 - locking pins)

Lay myWall panels face down on a clean floor.
Place both top and bottom sections next to each
other. Top section has the cut-outs for the french
cleat mounting at the top. The bottom panel has a

2

lower open section at the bottom.

(2 wooden blocks and 8 furniture screws are
provided with each of your myWall panel sets)

(Keep each box set together as a unit, don’t mix

panel sets between boxes)

3

Attach connector blocks to fasten top and
bottom of your myWall panel together.

(Easiest to place both top and bottom panels
face down on floor, slide the top and bottom
sections together and then attach 2 wood
connector blocks)

Locate metal or wood stud locations on wall for
mounting.

4

5

(Recommended use of a stud finder)

WARNING: Check for plumbing or electrical
locations within wall.

Mark location for French Cleat.

French cleat height from floor to base of cleat
can depend on use of panels.

Recommended height is 83.5 inches from floor
to bottom of french cleat.

(Ensure that French Cleat mounts level)

(Ensure to shim if needed for cleat to be
perfectly flat on wall)

6

7

Secure French Cleat to desired location with
correct mounting hardware. (not supplied)

Ensure that your cleat mounts level

(Correct mounting hardware will depend on
overall wall structure used for mounting. Mount
directly into wood studs, metal studs, concrete
block etc.) (Do not mount into drywall only) (use
any hole or slot on french cleat to mount) (mount
with a minimum of 2 screws)

Place your myWall panel on french cleat.

8

Attach safety locking plate to left or right side
of mywall panel.

(Locking plate is only needed on one side of
the panel)

Attach end-caps to each outer edge side of your
myWall panel set.

9

10

(2 screws are supplied for each side)
(The end-caps are used to hide the view of the
hanging cleat hardware)

Attach your accessories to the panel and ENJOY.

RENEWABLE
RESOURCES

The myWall system uses rubber wood, a
renewable and sustainable byproduct of the
latex industry.

Reduce: We work with our manufacturing
partners to ensure we are leaving as small a
carbon footprint as possible.

Re-use: Our products are durable and
designed to last, cutting down the need to
discard our products and purchase new ones.

Recycle: Our products and components use
recycleable materials.

myWall is a registered
trademark and patented
product of Thinkterior Co. Ltd,
Thailand.

All Rights Reserved.
©2020

AdaptivDC
42395 Ryan Road
Suite 112 / PMB 212
Ashburn, VA 20148

800. 693. 0068
[e-mail]
adaptivdc.com