Mytek Studio Clock 192CX – User Manual
Studio Clock 192CX
User Manual
ver. 1.0 / Jun 2011
© Mytek Digital 2011
www.mytekdigital.com Page: 1 / 9
Mytek Studio Clock 192CX – User Manual
This manual may be updated
Download the newest version at:
http://www.mytekdigital.com/download_library/
For technical support, technical tips and support check:
http://www.mytekdigital.com
or contact Mytek tech support at:
highend@mytekdigital.com
or at:
tel. (347) 384-2687
fax. (212) 202-5331
Mytek Digital
148 India St. FL 1
Brooklyn, NY 11222
USA
www.mytekdigital.com Page: 2 / 9
Mytek Studio Clock 192CX – User Manual
Content
Introduction..................................................................................4
Quick Start....................................................................................5
Front Panel....................................................................................5
Back Panel.....................................................................................6
Functions....................................................................................... 6
Table of Frequencies....................................................................7
Important Safety Instructions.....................................................8
www.mytekdigital.com Page: 3/9
Mytek Studio Clock 192CX – User Manual
Introduction
The Mytek Studio Clock 192CX is a house clock
generator/distributor that is designed specifically for audio
applications. It can generate its own clock based on the ultra
stable, ultra low jitter internal clock generator, or it can
redistribute an external wordclock source.
www.mytekdigital.com Page: 4/9
Mytek Studio Clock 192CX – User Manual
Quick Start
1. Connect Clock Signal Lines
Connect the FS WCK out to the wordclock input of your device. Set
the receiving device to slave to the external wordclock signal.
2. Operation
Once the unit is powered on it will generate wordclock based
on the settings on the front panel.
3. Configuration
The FS selector cycles through the standard audio sampling
rates. You can choose 44.1 kHz, 48 kHz, 88.2kHz, 96 kHz, 176.4
kHz, and 192 kHz. The unit can also be used to redistribute an
external clock source.
Front Panel
STUDIO CLOCK 192CX
96
192
48
ULTRA
PRECISION
INTERNAL
OSCILLATOR
CX7 97
A – Sampling Frequency Selector
B – Sampling Frequency Indicator
C – Clock Source Selector
D – Clock Source Indicator
E – Wordclock In Multiplier Selector
FS
A
176.4
88.2
44.1
MYTEK DIGITAL.USA
AAB
D
FS=
E
C
SOUR CE
WCK IN
INT OSC
F
WCK INx4
WCK INx2
WCK IN
I
O
G
F – Wordclock In Multiplier Indicator
G – Power Switch
www.mytekdigital.com Page: 5/9
Back Panel
Mytek Studio Clock 192CX – User Manual
110/220VAC
A
SWITCH AND FUSE INSIDE
B
SUPERCK OU T
C
WCK IN
A – IEC Power socket
B – Wordclock Input
C – Superclock Output
D – FS Wordclock Outputs
E – FS/2 Wordclock Output
F – FS/2/4 Wordclock Output
DESIGNED IN USA
D
6x FS WCK OUTS
MADE IN PO LAND
E
FS/FS:2 OUT
FS/FS:2/FS:4 OUT
F
AES OUT
FS
G
WWW .MYTEKDIGITAL .CO M
G – AES/EBU XLR Clock Output
Functions
FS – This cycles the sampling frequency between 44.1, 48, 88.2,
96, 176.4, and 192 kHz.
SOURCE – This selects whether the Internal Oscillator or the
External Wordclock In is the clock source.
FS= – This multiplies the incoming wordclock by x1, x2, or x4.
WCK IN – This is for connecting an external clock source.
FS WCK OUT – This outputs wordclock at the selected
sampling frequency.
SUPERCK OUT – This is always outputting Superclock.
FS/FS:2 OUT – This clock output divides the selected
sampling frequency by 2.
FS/FS:2/FS:4 OUT – This clock output divides the selected
sampling frequency by 2 and 4.
www.mytekdigital.com Page: 6/9
Mytek Studio Clock 192CX – User Manual
Table of Frequencies
Internal Oscillator (INT OSC)
FS FS WCK OUT FS/FS:2 OUT FS/FS:2/FS:4 OUT
44.1 kHz 44.1 kHz 44.1 kHz 44.1 kHz
48 kHz 48 kHz 48 kHz 48 kHz
88.2 kHz 88.2 kHz 44.1 kHz 44.1 kHz
96 kHz 96 kHz 48 kHz 48 kHz
176.4 kHz 176.4 kHz 88.2 kHz 44.1 kHz
192 kHz 192 kHz 96 kHz 48 kHz
External Wordclock (WCK IN)
Ext. Clock FS FS= FS WCK
OUT
44.1 kHz 44.1 kHz x1 44.1 kHz 44.1 kHz 44.1 kHz
48 kHz 48 kHz x1 48 kHz 48 kHz 48 kHz
88.2 kHz 88.2 kHz x1 88.2 kHz 44.1 kHz 44.1 kHz
96 kHz 96 kHz x1 96 kHz 48 kHz 48 kHz
176.4 kHz 176.4 kHz x1 176.4 kHz 88.2 kHz 44.1 kHz
192 kHz 192 kHz x1 192 kHz 96 kHz 48 kHz
44.1 kHz 44.1 kHz x2 44.1 kHz 44.1 kHz 44.1 kHz
44.1 kHz 88.2 kHz x2 88.2 kHz 44.1 kHz 44.1 kHz
48 kHz 48 kHz x2 48 kHz 48 kHz 48 kHz
48 kHz 96 kHz x2 96 kHz 48 kHz 48 kHz
88.2 kHz 176.4 kHz x2 176.4 kHz 88.2 kHz 44.1 kHz
96 kHz 192 kHz x2 192 kHz 96 kHz 48 kHz
FS/FS:2
OUT
FS/FS:2/FS:4
OUT
44.1 kHz 44.1 kHz x4 44.1 kHz 44.1 kHz 44.1 kHz
44.1 kHz 88.2 kHz x4 88.2 kHz 44.1 kHz 44.1 kHz
44.1 kHz 176,4 x4 176.4 kHz 88.2 kHz 44.1 kHz
48 kHz 48 kHz x4 48 kHz 48 kHz 48 kHz
48 kHz 96 kHz x4 96 kHz 48 kHz 48 kHz
48 kHz 192 kHz x4 192 kHz 96 kHz 48 kHz
www.mytekdigital.com Page: 7/9
Mytek Studio Clock 192CX – User Manual
Important Safety Instructions
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for
long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
www.mytekdigital.com Page: 8/9
Mytek Studio Clock 192CX – User Manual
WARNING
Excessive sound pressure from speakers and headphones can cause
hearing loss. In order to use this product safely, avoid prolonged
listening at excessive sound pressure levels.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
All interface cables used to connect peripherals must be shielded in
order to comply with the limits for a digital device pursuant to Subpart
B of Part 15 of FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This product with the CE marking complies with the EMC Directive
issued by the Commission of the European Community. Compliance
with this directive implies conformity to the following European
standards:
• EN55103-1 : Electromagnetic Interference (Emission)
• EN55103-2 : Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following Electromagnetic
Environments: E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors), E4 (controlled EMC environment, ex. TV studio).
www.mytekdigital.com Page: 9/9
Loading...