Mytee Speedster 1000DX-200, Speedster 1000DX, Speedster 1001DX, Speedster 1001DX-200, Speedster 1003DX Instructions Manual

Instructions for

1000DX, 1000DX-200, 1001DX,
1001DX-200, 1003DX, 1005DX Speedster

Please read before use.

Register your product
at www.mytee.com/help

®

1000DX & 1000DX-200 p.3
1001DX & 1001DX-200 p.9
1003DX p.15
1005DX p.21
General information p.27

Model #

Serial #

Form # ADM-Speedster

12-10

13655 Stowe Dr., Poway, Ca. 92064

1

2

1000DX & 1000DX-200 SPEEDSTER

1000DX & 1000DX-200 SPEEDSTER® BACK1000DX & 1000DX-200 SPEEDSTER® FRONT

10

9

8

1. Switch plate

2. 2” Male Cuff-Lynx™

3. Solution lid

4. Female quick disconnect (QD)

5. Front handle

1

2

6. Front vent

7. Bottom handle

8. 5” locking casters

9. Solution tank

10. Recovery lid

11

12

3

4

5

13

14

6

7

11. Recovery tank

12. Push handle

13. Drain valve

14. Power cord

16

15. Back vent

16. 12” Rear wheels

15

1000DX & 1000DX-200 SPEEDSTER® ITEMS INCLUDED

H110 Cuff-Lynx™ H141 Cuff-Lynx™
2” Hose Adapter 2” Hose Reducer to 1.5”

H375- Hose Hanger H226 Drain Elbow

(4) screws

1000DX & 1000DX-200 SPEEDSTER® CORD

Plug the power cord into a single, 20A grounded wall outlet.

3

1000DX & 1000DX-200 SPEEDSTER

1000DX & 1000DX-200 SPEEDSTER® VAC/SOL

HOSE CONNECTIONS

Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® Cuff­Lynx™ vacuum hose port.

1000DX & 1000DX-200 SPEEDSTER® SWITCHES

Vac 1 Vac 2

Pump

Turn on Vac 1, Vac 2 and Pump switches.

1000DX & 1000DX-200 SPEEDSTER® FILL

SOLUTION TANK

Lift lid and manually ll the tank.

1000DX & 1000DX-200 SPEEDSTER® BALL FLOAT

An internal ball oat automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear drain valve.

4

1000DX & 1000DX-200 SPEEDSTER

1000DX & 1000DX-200 SPEEDSTER® DUMP VALVE

Attach the 45˚ drain elbow to the drain spout in back. Lift up the
dump valve and empty the tank.

1000DX & 1000DX-200 SPEEDSTER

®

FILTER MAINTENANCE

INTAKE
FILTER

Check and clean solution tank lter daily by twisting off, rinsing with
clean water and replacing.

1000DX & 1000DX-200 SPEEDSTER

®

LOCKING CASTERS

Locking casters help keep the machine remain stationary during
use.

MYTEE® SYSTEM MAINTAINER

Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.

5

1000DX & 1000DX-200 SPEEDSTER

F

1

2

E

D

C

B

A

PRODUCTS, INC.

858-679-1191

speedster

mytee

TITLE:

DATE

10/12/10

NAME

J. Cash

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

CHECKED

DRAWN

REV

SHEET 1 OF 2

1

DO NOT

SCALE DRAWING

1000DX

DWG. NO.

C

SCALE: 1:8

SIZE

2

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS

PROHIBITED.

MSRP

3

1 $1.99 ea

1 $8.99 ea

2 $0.99 ea

2 $6.99 ea

1 $20.99 ea

valve, drain, 1-1/2"

bracket, "L" (all extracters)

bracket, front hinge, sp/fb

4

1 $31.99 ea

1 $6.49 ea

QTY.

DESCRIPTION

filter, strainer, 1/2"

1 $2.49 ea

nipple, brass, 3/8" x close

bushing, brass, 1/2"mpt x 3/8" fpt, hex

hose, 3/8" x 17-1/2", (OAL), f x -fsw, surge, 1600psi

5

6

PART NO.

NO.

ITEM

AH105

54

B119A

55

B216

B210

H378

H316 bolt, 1/4-20 x 1-1/2" hex head, s/s

H225

H390A

59

60

61

58

57

56

$7.99/ft

1 $3.19 ea

1 $6.49 ea

spout, drain, 45 degree

1 $11.49 ea

1 $6.99 ea

1 $18.49 ea

pipe, pvc, 2" 1

elbow, 2" float

float, 2", ball style

adaptor, pvc 2, fmsl x fmt

1 $11.99 ea

1 $36.99 ea

1 $15.99 ea

gasket, 7", vac lid

lid, vac tank, black, 7"

elbow, inlet assembly 2"

1 $2.49 ea

6 $0.99 ea

1 $190.99 ea

gasket, 2" inlet

vac tank, speedster

screw, #8 x 5/8 phil oval, s/s

gasket, cam fitting polyethylene, 2.35" OD 1.90" ID

H226

62

G002

63

P684

64

P682

65

H490

66

P726

67

A926

68

G091

69

G090

70

H304

71

P733

72

G083

73

2 $0.99 ea

2 $0.99 ea

1 $6.99 ea

1 $10.99 ea

1 $3.99 ea

3 $13.99 ea

inlet, 2"

washer, #8 flat, s/s

plate, switch, sp, 3 hole

switch, rocker, 2 position

Cuff-Lynx, 2" m cuff x 2" mpt

screw, #10-32 x 1/2" SHCS, alloy

H135

74

E515

75

H338

76

H389

77

H612

78

P685

79

$8.99/ft

MSRP

1 $208.99 ea

QTY

DESCRIPTION

pump, 220psi, demand, 120V

C322D

PART NO.

44

NO.

ITEM

1000DX-200

$8.99/ft

MSRP

1 $74.99

1 $9.99 ea

2 $4.99 ea

QTY

DESCRIPTION

gasket, strip, 3/4" x 36" x 1/8"

filter, bag, vac tank, drawstring

power cord, ext, 50', 12/3, black

E530

G010

G085

PART NO.

Items Not Shown

1 $3.99 ea

1 $3.99 ea

1 $10.99 ea

hanger, wire formed, hose

Cuff-Lynx, 2" to 1.5" reducer

Cuff-Lynx, female swivel x female thread 2"

H375

H140

H141

3

4

5

6

8 $0.99 ea

2 $2.99 ea

QTY.

7

10 $0.99 ea

DESCRIPTION

guard, cooling fan, wire

screw, #10 x 5/8" hex head, zinc

8 $0.99 ea

2 $6.99 ea

19 $0.99 ea

2 $23.19 ea

13 $0.99 ea

1 $141.99 ea

caster, 5"

washer, 1/4" flat, s/s

handle, breeze and dx

washer, 1/4"id x 1"od, flat, s/s

base, speedster

nut, lock, 1/4-20 nylon insert

bolt, 1/4-20 x 1" hex head, s/s 8 $0.99 ea

4 $0.99 ea

washer, axle, cut 1/2" id

2 $41.99 ea

2 $0.99 ea

1 $9.99 ea

wheel, 12"

cap, axle, 1/2"

axle, 18.25" x .50" dia

1 $1.99 ea

nut, lock, 1/2" steel

connector, cord lock

1 $4.99 ea

bolt, 1/4-20 x 1/2" serrated hex flange, zinc

8

PART NO.

NO.

ITEM

H343

1

H296

2

H770

3

F

H211

4

H485

5

H210

6

H342

7

H666

8

H216

9

P731

10

H254

11

H251

12

E

H219

13

H371

14

H221

15

G131

16

1 $11.49 ea

1 $3.19 ea

8 $0.99 ea

1 $13.49 ea

1 $15.99 ea

2 $8.99 ea

6 $3.99 ea

11 $0.99 ea

fitting, strain relief, cord

plate, manifold, parallel

bolt, 1/4-20 x 1/2", hex head, zinc

power cord, pigtail, 30", 12/3, black

bolt, 1/4-20 x 3/4" serrated hex flange, zinc

E550

H220

H201

H601

H768

17

18

19

20

21

D

2 $103.99 ea

gasket, vacuum motor

vac support, 2 stage, 3-1/8"

manifold, dual vac, parallel

vac motor, 2 stage high performance

P750

H500

C310

G004

22

23

24

25

1

1 $12.49 ea

2 $4.99 ea

exhaust boot, plastisol

vac hose, 2", wire reinforced

cuff hose, 2 X 2, wire reinforced

1

3 $1.49 ea

1 $9.49 ea

4 $0.99 ea

nut, kep, #10-32 zinc

clamp, hose, 2-1/4 dia

sol hose, 1/2" kuri 100psi

elbow, brass, 90 deg, 1/2" barb x 3/8"mpt

B172

H544

H217

G059

26

PH628-24

27

H273

PH615-26

31

28

32

29

30

C

6

4 $0.99 ea

1 $4.99 ea

1 $3.19 ea

4 $1.99 ea

1 $3.49 ea

5 $0.99 ea

clamp, hose, 5/16-29/32

washer, 11/16"id x 1-1/2"od x .075, s/s

adapter, brass, 1/2" barb x 3/8" fsw, ball end

B160

H347

H299

33

34

35

4 $0.99 ea

1 $8.99 ea

2 $4.49 ea

nipple, brass, 1/4"m, hex

washer, 9/16"id x 1"od, flat, s/s

elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt

elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt

B186

B103

B107

H212

39

36

37

38

1 $151.99 ea

bushing, brass, 3/8"mpt x 1/4" 1 $3.19 ea

pump, 120psi, demand, 115V

elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt

screw, #10-32 x 1-1/4" phil pan head, zinc

B105

B136

H222

C305

43

41

42

40

B

Part prices are subject to change.Order parts at: www.mytee.com/products/product.php?id=1000DX

1 $9.99 ea

2 $0.99 ea

6 $1.99 ea

4 $0.99 ea

2

1

2

nut, hex, 1/4-20 s/s

bracket, rear, fb/spy

bolt, 1/4-20 x 1-1/4" hex head

H912

H203

44

45

sol tank, speedster

washer, 1/4" lock, s/s

washer, buna 1-1/8" od x 3/16" id

G052

46

washer, nylon, 9/16id x 1-1/16od x .031

P732

H213

H215

H413

47

48

49

50

A

1

1

1

7

qd, brass, 1/4" f

nipple, brass, 1/4" x close

adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex

8

B102

B106

B111

52

53

51

D

C

B

A

1

E

F

1000DX

SHEET 2 OF 2

speedster

REV

DWG. NO.

mytee

PRODUCTS, INC.

858-679-1191

DO NOT SCALE

DRAWING

2

1000DX & 1000DX-200 SPEEDSTER

74

73

71

72

70

68

69

75

76

77

78

TITLE:

DATE

10/12/10

NAME

J. Cash

CHECKED

DRAWN

D

SCALE: 1:7

SIZE

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS PROHIBITED.

1

79

3

60

2

to pump "OUT"

thru B106 (#54)

39

50

61

62

3

52

51

21

5

4

46

6

to female QD

thru B111 (#52)

53

37

47

19

58

9

59

56

35

to pump "OUT"

54

thru B107 (#39)

4

55

67

63

64

65

66

3

4

49

57

48

47

4

46

46

4

5

45

3

to pump "IN"

thru B186 (#36)

3

44

5

6

7

28

27

25

21

8

to female QD

thru AH105-18 (#55)

39

38

29

26

1

30

2

3

43

6

31

42

41

40

36

37

to sol tank filter

35

33

34

thru B216 (#58)

32

10

11

18

15

17

14

4

6

9

5

7

8

6

7

12

19

16

13

20

22

23

24

21

9

6

8

7

1000DX & 1000DX-200 SPEEDSTER

515E515E

Inline Conn.

Green

White

Black

GND

L1

L2

Inline Conn.

Black

Brown

Vacuum Motor 2

13655 Stowe Dr.

Poway, CA

92064

Mytee Products

---1

Inline Conn.

Inline Conn.

Green

White

Black

GND

L1

L2

Inline Conn.

Black

SW-DPST SW-DPST

Yellow

Vacuum Motor 1

1

Revision:

Sheet of

0000 A

Time:

Inline Conn.

Letter

11/30/2010 1:49:31 PM

1000DX

Title

C:\Compaines\GHI\Projects\Mytee Schematics\1000DX\1000DX.SCHDOC

Size: Number:

Date:

File:

Green Green

White

Green

White

GND

L2

L1

Black

BlackBlack

Switch

Pressure

Inline Conn.

Blue

Pressure Pump

C322D 013C013C

E515

SW-DPST

Black Black Black

Inline Conn. Inline Conn.

Black

Green

Black

White

GND

L1

L2

Cord Input Primary

8

1001DX & 1001DX-200 SPEEDSTER

1001DX & 1001DX-200 SPEEDSTER® BACK1001DX & 1001DX-200 SPEEDSTER® FRONT

10

9

8

1. Switch plate

2. 2” Male Cuff-Lynx™

3. Solution lid

4. Female quick disconnect (QD)

5. Front handle

1

2

6. Front cooling fan

7. Bottom handle

8. 5” locking casters

9. Solution tank

10. Recovery lid

11

12

3

4

5

13

14

6

7

11. Recovery tank

12. Push handle

13. Drain valve

14. Dual power cords

16

15. Back vent

16. 12” Rear wheels

15

1001DX & 1001DX-200 SPEEDSTER® ITEMS INCLUDED

H110 Cuff-Lynx™ H141 Cuff-Lynx™
2” Hose Adapter 2” Hose Reducer to 1.5”

H375- Hose Hanger H226 Drain Elbow

(4) screws

1001DX & 1001DX-200 SPEEDSTER® CORDS

Left cord: Powers Vac 2 & Heater 2.

Right cord: Powers Vac 1, Heater 1 & Pump.

Yellow tag

indicates primary

cord.

Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.

9

1001DX & 1001DX-200 SPEEDSTER

1001DX & 1001DX-200 SPEEDSTER® VAC/SOL

HOSE CONNECTIONS

Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® Cuff­Lynx™ vacuum hose port.

1001DX & 1001DX-200 SPEEDSTER® SWITCHES

Heater 1Vac 1 Vac 2

Pump Heater 2

“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. To activate heat, turn on Heater switch.
Heater 1 for 1000 watts of heat. Heater 2 for 2000 watts of heat.

1001DX & 1001DX-200 SPEEDSTER

FILL SOLUTION TANK

Lift lid and manually ll the tank.

®

1001DX & 1001DX-200 SPEEDSTER

®

FILTER MAINTENANCE

INTAKE
FILTER

Check and clean solution tank lter daily by twisting off, rinsing
with clean water and replacing.

10

1001DX & 1001DX-200 SPEEDSTER

1001DX & 1001DX-200 SPEEDSTER® BALL FLOAT

An internal ball oat automatically turns off the machine’s
vacuum when the water in the solution tank reaches its maxi­mum level. Empty the recovery tank as needed using the rear
dump valve.

1001DX & 1001DX-200 SPEEDSTER® DUMP VALVE

Attach the 45˚ drain elbow to the drain spout in back. Lift up the
dump valve and empty the tank.

1001DX & 1001DX-200 SPEEDSTER

®

LOCKING CASTERS

Locking casters help keep the machine remain stationary during
use.

MYTEE® SYSTEM MAINTAINER

Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.

11

1001DX & 1001DX-200 SPEEDSTER

D

C

B

E

F

A

1

2

REV

PRODUCTS, INC.

858-679-1191

speedster

mytee

TITLE:

DATE

9/24/2010

NAME

J. CAsh

CHECKED

DRAWN

SHEET 1 OF 2

1

DO NOT

SCALE DRAWING

1001DX

DWG. NO.

C

SCALE: 1:8

SIZE

2

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS

PROHIBITED.

3

4

5

6

MSRP

QTY.

DESCRIPTION

PART NO.

ITEM

MSRP

QTY.

$0.99 ea

$9.99 ea

1

bracket, rear, fb/spy

H912

54

NO.

$2.99 ea

$0.99 ea

3

12

$0.99 ea

$0.99 ea

$1.99 ea

2

6

4

2

nut, hex, 1/4-20 s/s

washer, 1/4" lock, s/s

bolt, 1/4-20 x 1-1/4" hex head

washer, buna 1-1/8" od x 3/16" id

H203

H213

H215

G052

55

56

57

58

$0.99 ea

$0.99 ea

$21.49 ea

8

1

10

$8.99 ea

$2.49 ea

$1.99 ea

$3.19 ea

$0.99 ea

$3.49 ea

2

1

1 $141.99

sol tank, speedster

$3.49 ea

$17.99 ea

1

1

1

qd, brass, 1/4" f

nipple, brass, 1/4" x close

washer, nylon, 9/16id x 1-1/16od x .031

$0.99 ea

$6.49 ea

1

1

1

2

1

filter, strainer, 1/2"

nipple, brass, 3/8" x close

bracket, front hinge, sp/fb

bolt, 1/4-20 x 1-1/2" hex head, s/s

bushing, brass, 1/2"mpt x 3/8" fpt, hex

adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex

B216

B106

B210

B107 nipple, brass, 1/4"m, hex

B111

B102

P732

H413

59

60

$0.99 ea

$6.99 ea

2

19

61

62

$0.99 ea

$23.19 ea

2

64

63

$0.99 ea

$141.99 ea

1

13

$0.99 ea

4

B119A

65

66

$41.99 ea

2

H316

67

68

$0.99 ea

$9.99 ea

2

1

H378

69

$4.99 ea

2

$7.99/ft

$6.49 ea

$6.99 ea

$6.99 ea

$18.49 ea

1

1

pipe, pvc, 2" 1

float, 2", ball style

$11.49 ea

1

elbow, 2" float

$20.99 ea

1

2

1

valve, drain, 1-1/2"

bracket, "L" (all extracters)

$0.99 ea

$15.99 ea

$11.99 ea

$36.99 ea

1

1

1

6

gasket, 7", vac lid

lid, vac tank, black, 7"

elbow, inlet assembly 2"

screw, #8 x 5/8 phil oval, s/s

gasket, cam fitting polyethylene, 2.35" OD 1.90" ID

P684 adaptor, pvc 2, fmsl x fmt

P682

H225

H390A

70

71

$3.19 ea

$11.49 ea

2

2

G002

73

72

$1.99 ea

31.99 ea

2

2

H490

74

75

$4.49 ea

$23.99 ea

4

2

P726

76

$0.99 ea

$0.99 ea

6

6

A926

G091

78

77

$29.99 ea

1

H304

G090

79

80

$0.99 ea

$51.99 ea

2

10

$2.49 ea

$5.99 ea

$3.99 ea

$190.99 ea

1

vac tank, speedster

P733

81

$4.49 ea

$13.99 ea

1

1

$14.99 ea

1

1

2

1

gasket, 2" inlet

light, red, 250v

switch, rocker, 3 position

Cuff-Lynx, 2" m cuff x 2" mpt

E511

E516

H135

G083

84

85

82

83

$78.99 ea

$17.99 ea

$16.49 ea

2

2

2

$9.99 ea

$6.99 ea

$0.99 ea

$13.99 ea

3

$0.99 ea

$10.99 ea

1

1

3

3

1

inlet, 2"

washer, #8 flat, s/s

plate, switch, sp, 4 hole

switch, rocker, 2 position

light, indicator, 125v (amber)

screw, #10-32 x 1/2" SHCS, alloy

E515

E512B

86

87

$0.99 ea

$13.49 ea

4

1

$0.99 ea

11

H348

H389

88

89

$15.99 ea

1

P685

H612

90

91

$8.99 ea

$3.99 ea

2

6

$103.99 ea

2

MSRP

$208.99 ea

1

QTY

DESCRIPTION

pump, 220psi, demand, 120V

C322D

PART NO.

58

NO.

ITEM

1001DX-200

$8.99/ft

1

$1.49 ea

$12.49 ea

1

3

$0.99 ea

8

$4.99 ea

2

MSRP

$9.99 ea

$4.99 ea

$3.99 ea

$74.99 ea

2

1

2

QTY

1

DESCRIPTION

gasket, strip, 3/4" x 36" x 1/8"

filter, bag, vac tank, drawstring

power cord, ext, 50', 12/3, black

Cuff-Lynx, female swivel x female thread 2"

E530

H140

G010

G085

PART NO.

Items Not Shown

$8.99/ft

$3.49 ea

$8.99 ea

$1.99 ea

1

4

1

$0.99 ea

5

$9.49 ea

1

1

3

$3.99 ea

$10.99 ea

1

1

4

hanger, wire formed, hose

Cuff-Lynx, 2" to 1.5" reducer

5

H141

H375

$151.99 ea

1

6

$4.99 ea

$3.19 ea

1

1

7

DESCRIPTION

fan, cooling, 115V

guard, cooling fan, wire

screw, #10 x 5/8" hex head, zinc

handle, breeze and dx

washer, 1/4"id x 1"od, flat, s/s

caster, 5"

washer, 1/4" flat, s/s

bolt, 1/4-20 x 1" hex head, s/s 8

wheel, 12"

cap, axle, 1/2"

base, speedster

axle, 18.25" x .50" dia

washer, axle, cut 1/2" id

connector, cord lock

nut, lock, 1/4-20, nylon insert, s/s

bolt, 1/4-20 x 1/2" serrated hex flange, zinc

8

P731

H666

H216

H254

H251

H219

PART NO.

NO.

ITEM

H343

1

H296

2

C317

3

H770

4

H211

5

H485

6

H210

7

H342

8

9

10

11

H371

G131

12

13

14

15

16

nut, lock, 1/2" steel

fitting, strain relief, cord

power cord, pigtail, 30", 12/3, black

E550

H220

H221

17

18

19

nut, kep, #10-32 zinc

hose, 3/8" x 17-1/2", (OAL), f

hose, 3/8" x 6", (OAL), f x fsw, surge, 1600psi

AH105

AH156

20

21

bracket, heater mounting, dual

elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt

screw, #10-32 x 1-1/4" phil pan head, zinc

screw, 6 x 3/16, phil pan head, self tapping

B103

H273

H222

H528

H274

23

24

25

22

26

valve, brass, 1/4" check

heating rod, 1000W, 115V

coupling, brass, 1/4" fpt x 1/4" fpt

E519

B142

27

28

Thermostat, 200°, Auto, 1/4"

washer, 9/16"id x 1"od, flat, s/s

heater, aluminum cast, single

Thermostat, 310°F ± 10°F, Manual, 1/4"

E574

E573

B108

29

H903A

30

H212

31

32

33

12

exhaust boot, plastisol

gasket, vacuum motor

plate, manifold, parallel

H601

34

vac support, 2 stage, 3-1/8"

manifold, dual vac, parallel

bolt, 1/4-20 x 3/4" serrated hex flange, zinc

H768

35

vac motor, 2 stage high performance

P750

H500

C310

G004

37

38

39

36

clamp, hose, 2-1/4 dia

vac hose, 2", wire reinforced

cuff hose, 2 X 2, wire reinforced

H544

H217

G059

PH628-24

41

42

43

40

Part prices are subject to change.Order parts at: www.mytee.com/products/product.php?id=1001DX

sol hose, 1/2" kuri 100psi

clamp, hose, 5/16-29/32

bolt, 1/4-20 x 1/2", hex head, zinc

elbow, brass, 90 deg, 1/2" barb x 3/8"mpt

B172

H201

44

45

elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt

adapter, brass, 1/2" barb x 3/8" fsw, ball end

B186

B160

H347

PH615-26

49

46

47

48

bushing, brass, 3/8"mpt x 1/4"

pump, 120psi, demand, 115V

washer, 11/16"id x 1-1/2"od x .075, s/s

elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt

B136

B105

H299

C305

52

53

50

51

7

8

D

C

B

A

E

F

1001DX

SHEET 2 OF 2

speedster

REV

PRODUCTS, INC.

858-679-1191

DO NOT SCALE

DRAWING

1

80

82

81

79

78

2

77

1001DX & 1001DX-200 SPEEDSTER

83

85

84

86

87

88

89

90

91

4

70

DATE

NAME

mytee

9/24/2010

J. Cash

DRAWN

TITLE:

CHECKED

DWG. NO.

D

SCALE: 1:6

SIZE

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS PROHIBITED.

1

2

76

74

73

72

71

75

3

62

to heater

thru AH105-18 (#20)

61

33

60

35

6

5

56

7

to female QD

thru B111 (#61)

64

22

57

20

to heater

thru AH105-18 (#20)

33

63

3

44

59

4

58

57

5

56

56

5

69

10

68

4

4

54

65

66

50

67

to pump "IN"

thru B186 (#49)

22

4

55

1

5

45

53

7

23

24

3

5

4

7

8

6

5

52

51

6

to heater

thru AH156 (#21)

42

41

7

39

35

8

43

40

38

37

50

49

to sol tank filter

thru B216 (#67)

36

10

10

46

47

48

19

11

15

12

9

2

6

18

17

44

16

to female QD

thru B103 (#22)

34

13

14

to pump "OUT"

20

thru B136 (#51)

22

21

21

7

35

7

29

28

30

27

23

24

25

31

32

26

8

13

1001DX & 1001DX-200 SPEEDSTER

White

White / Red

Green

White

Green

Thermal Switch

Green

Green

White

White / Red

Green

Thermal Switch

White

013C013C

Inline Conn.

GND

Green

L2

Black

Inline Conn.

Circuit Detector

E564

L1a

L2a

Light 1
Light 2

L2b

L1b

Black

Pink 18 AWG
Pink 18 AWG

Red

E512B

Lamp Amber

C317

Cooling Fan

Heater 2

GND

Black

13655 Stowe Dr.

Poway, CA

92064

---1

Mytee Products

1

Revision:

Sheet of

C519C519

Switch

Thermal

L1 L2

Black

Orange

0000 A

Time:

GND

Switch

Thermal

L1 L2

Heater 1

Orange / Black

Letter

11/30/2010 10:45:09 AM

1001DX

Title

C:\Compaines\GHI\Projects\Mytee Schematics\1001DX\1001DX.SCHDOC

Size: Number:

Date:

File:

515E515E

Inline Conn.

L1

Brown

Black

Orange

Vacuum Motor 2

Inline Conn.

GND

Green

L2

Black

White

Inline Conn.

L1

Black

SW-DPST SW-DPST

Yellow

Inline Conn.

Green

Green

Vacuum Motor 1

Orange / Black

E511

E511

Orange

Lamp Heater 1

Lamp Heater 2

White White White

Inline Conn.

Green

White

Black

Inline Conn.

Green

Green

White / Red White / Red White / Red White / Red

C322D

GND

L2

L1

Pressure

Inline Conn.

Black

Switch

Pressure Pump

Black

E515

SW-DPST

Blue

Black Black Black

Heater Switch

Red Red Red Red Red

Red

Black

E516

3-Position

Red

White Red White / Red

Inline Conn.

Inline Conn.

GND

L1

L2

Black

L1

White

GND

L2

Cord Input Primary

Entry Location, Top or Far Right

Cord Input Secondary

or Far Left

Entry Location, Bottom

14

1003DX SPEEDSTER

1003DX SPEEDSTER® BACK1003DX SPEEDSTER® FRONT

10

1

2

11

3

4

5

6

7

1. Switch plate

2. 2” Male Cuff-Lynx™

3. Solution lid

4. Female quick disconnect (QD)

5. Front handle

6. Front cooling fan

7. Prime Valve

8. Pressure Regulator

9. Solution tank

10. Recovery lid

1003DX SPEEDSTER® ITEMS INCLUDED

12

13

9

14

17

15

8

11. Push handle

12. Recovery tank

13. Drain valve

14. Back vent

15. Dual Power cords

16

16. 12” Rear wheels

17. 5” locking casters

1003DX SPEEDSTER® CORD

Left cord: Powers Vac 2 & Heater 2.

Right cord: Powers Vac 1, Heater 1 & Pump.

H110 Cuff-Lynx™ H141 Cuff-Lynx™

2” Hose Adapter 2” Hose Reducer to 1.5”

H375- Hose Hanger H226 Drain Elbow

(4) screws

Yellow tag

indicates primary

cord.

Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.

15

1003DX SPEEDSTER

Speedster Prime Label

1003DX SPEEDSTER® VAC/SOL

HOSE CONNECTIONS

Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s®
Cuff-Lynx™ vacuum hose port.

1003DX SPEEDSTER® SWITCHES

Vac 1 Vac 2

Pump

“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. To activate heat, use lower right switch.
Press to the left for 1,000 watts, press to the right for 2,000 watts.

Heater

1 2

1003DX SPEEDSTER® FILL SOLUTION TANK

Lift lid and manually ll the tank.

1003DX SPEEDSTER® PRIME VALVE

& PRESSURE REGULATOR

PRIME POSITION

HIGHER PSI

PRESSURE
REGULATOR

RUN POSITION

Prime the pump by turning the valve to the Prime position (as
shown above) for 30 seconds, then turn right to the Run position.
Turn the Pressure Regulator to the left to decrease water pres­sure. Turn the Pressure Regulator to the right to increase water
pressure.

LOWER PSI

16

1003DX SPEEDSTER

1003DX SPEEDSTER® FILTER MAINTENANCE

INTAKE
FILTER

Check and clean solution tank lter daily by twisting off, rinsing
with clean water and replacing.

1003DX SPEEDSTER® BALL FLOAT

An internal ball oat automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear dump valve.

1003DX SPEEDSTER® DUMP VALVE

& LOCKING CASTERS

Above, empty the recovery tank by attaching the 45˚ drain elbow to
the drain spout in back. Lift up the dump valve and empty the tank.
Below, locking casters help keep the machine remain stationary
during use.

MYTEE® SYSTEM MAINTAINER

Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.

17

1003DX SPEEDSTER

$74.99 ea

$62.49 ea

$10.99 ea

A

3

4

MSRP

1

2

1 $9.99 ea

QTY

DESCRIPTION

filter, bag, vac tank

controller, circuit light

power cord, ext, 50', 12/3, black

E530

E564

G010

PART NO.

Items Not Shown

2 $4.99 ea

1 $3.99 ea

1 $3.99 ea

1

hanger, wire formed, hose

Cuff-Lynx, 2" to 1.5" reducer

gasket, strip, 3/4" x 36" x 1/8"

Cuff-Lynx, female swivel x female thread 2"

H140

H141

H375

G085

MSRP

$8.99/ft

3 $3.49 ea

1

1 $2.49 ea

2 $8.99 ea

2 $1.99 ea

QTY.

5

DESCRIPTION

sol hose, 1/2" kuri 100psi

nipple, brass, 3/8" x close

adapter, brass, 1/2" barb x 1/4" mpt

elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt

6

7

PART NO.

NO.

ITEM

MSRP

QTY.

B216

56

1 $30.49 ea

adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex

B111

B644

B186

PH615-24

60

58

59

57

1 $13.49 ea

3 $3.19 ea

2 $4.99 ea

14 $0.99 ea

$8.99/ft

1 $141.99 ea

2 $0.99 ea

1 $9.99 ea

2 $6.99 ea

4 $0.99 ea

1 $5.49 ea

1

1 $8.49 ea

1 $86.99 ea

regulator, 450 psi

C313C

61

tee, brass, 1/4" mpt

sol hose, 1/2" kuri 100psi

bushing, brass, 3/8"mpt x 1/4" 1 $3.19 ea

elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt

B135

B105

B652

PH615-12

65

63

64

62

$7.99/ft

1

3 $2.99 ea

2 $7.99 ea

16 $1.99 ea

sol tank, speedster

bracket, rear, fb/spy

washer, 1/4" lock, s/s

bracket, "L" (all extracters)

bolt, 1/4-20 x 1-1/4" hex head

P732

H203

H912

H213

H390A

68

69

70

67

66

1 $21.49 ea

2 $23.19 ea

16 $0.99 ea

20 $0.99 ea

12 $0.99 ea

2 $3.49 ea

1 $6.99 ea

1 $17.99 ea

1 $31.99 ea

2 $0.99 ea

6 $1.99 ea

6 $0.99 ea

qd, brass, 1/4" f

nut, hex, 1/4-20 s/s

washer, 1/4"id x 1"od, flat, s/s

washer, buna 1-1/8" od x 3/16" id

washer, nylon, 9/16id x 1-1/16od x .031 4 $0.99 ea

H413

H215

H211

G052

74

73

72

71

1 $141.99 ea

2 $41.99 ea

4 $0.99 ea

handle, breeze and dx

nipple, brass, 1/4" x close

hose, 3/8" x 17-1/2", (OAL), f

B106

B102

H485

AH105

78

76

77

75

2 $3.19 ea

2 $1.99 ea

1 $9.99 ea

2 $0.99 ea

1 $6.99 ea

1 $18.49 ea

1 $6.49 ea

1 $3.19 ea

1 $20.99 ea

1 $6.49 ea

1 $8.99 ea

5 $0.99 ea

2 $0.99 ea

filter, strainer, 1/2"

valve, drain, 1-1/2"

bracket, front hinge, sp/fb

bolt, 1/4-20 x 1-1/2" hex head, s/s

washer, 11/16"id x 1-1/2"od x .075, s/s

H225

H299

H378

H316

B119A

83

81

82

80

79

1 $29.99 ea

2 $0.99 ea

2 $4.99 ea

2 $78.99 ea

2 $11.49 ea

float, 2", ball style

spout, drain, 45 degree

adaptor, pvc 2, fmsl x fmt

gasket, cam fitting polyethylene, 2.35" OD 1.90" ID

P684

H490

H226

G002

86

87

85

84

2 $51.99 ea

2 $17.99 ea

4 $0.99 ea

10 $0.99 ea

$7.99/ft

1 $3.99 ea

1 $2.49 ea

1 $11.99 ea

6 $0.99 ea

1 $36.99 ea

1 $190.99 ea

1 $15.99 ea

3 $0.99 ea

1 $11.49 ea

pipe, pvc, 2" 1

elbow, 2" float

vac tank, speedster

elbow, inlet assembly 2"

screw, 10 x 3/4, self-tap, hex head, zinc

P682

P733

P726

H118

A926

90

92

91

89

88

1 $13.49 ea

8 $0.99 ea

3 $26.49 ea

1 $23.99 ea

2 $16.49 ea

gasket, 2" inlet

gasket, 7", vac lid

lid, vac tank, black, 7"

screw, #8 x 5/8 phil oval, s/s

Cuff-Lynx, 2" m cuff x 2" mpt

H135

H304

G083

G091

G090

97

96

95

94

93

8 $0.99 ea

2 $4.99 ea

2 $8.99 ea

1 $15.99 ea

10 $0.99 ea

3 $0.99 ea

2 $0.99 ea

1 $8.99 ea

1 $9.99 ea

light, indicator, 125v (amber)

plate, switch, sp, 4 hole w/gauge

H337

E512B

99

98

6 $4.99 ea

2 $140.99

1 $0.99 ea

2 $5.99 ea

3 $13.99 ea

1 $14.99 ea

light, red, 250v

switch, rocker, 2 position

switch, rocker, 3 position

screw, #10-32 x 1/2" SHCS, alloy

screw, 8-32 x 3/8" SHCS, alloy, Black

E515

E516

E511

100

3 $1.49 ea

101

102

$8.99/ft

1

1 $12.49 ea

H246

H389

104

103

4 $1.99 ea

1 $27.99 ea

washer, #10 flat, s/s

H289

105

1 $10.99 ea

1 $5.49 ea

1 $38.99 ea

inlet, 2"

gauge, pressure, 2000 PSI

45 deg, street elbow, brass, 1/4" male NPTF

B130

P685

H308D

108

107

106

$8.99/ft

1

2 $2.49 ea

2 $3.49 ea

3 $9.49 ea

1 $13.99 ea

DESCRIPTION

hose, 3/8" x 10", (OAL), f x f

8

AH103

PART NO.

1

NO.

ITEM

ball valve, 1/4''

washer, 9/16"id x 1"od, flat, s/s

elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt

B656

B107 nipple, brass, 1/4"m, hex

B136

H212

5

4

3

2

F

sol hose, kuriyama, 3/8"

guard, cooling fan, wire

clamp, hose, 5/16-29/32

adapter, brass, 3/8" barb x 1/4" fsw

elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt 11 $4.49 ea

B103

B235

6

7

screw, #10 x 5/8" hex head zinc

H343

H347

H296

PH715-25

8

9

11

10

caster, 5"

fan, cooling, 115V

washer, 1/4" flat, s/s

nut, lock, 1/4-20 nylon insert

H216

H210

H666

C317

13

14

15

12

wheel, 12"

base, speedster

washer, axle, cut 1/2" id

bolt, 1/4-20 x 1" hex head, s/s 12 $0.99 ea

P731

H254

H251

H342

17

18

19

16

E

cap, axle, 1/2"

nut, lock, 1/2" steel

connector, cord lock

fitting, strain relief, cord

axle, 1/2" x 18-1/2", sp, breeze

H221

H371

H219

22

21

20

heater, aluminum cast, single

power cord, pigtail, 30", 12/3, black

E550

H220

G131

H903A

26

25

24

23

nut, kep, #10-32 zinc

heating rod, 1000W, 115V

bracket, heater mounting, dual

screw, #10-32 x 3/4" phil pan head, zinc

H256

H273

H528

28

29

27

D

Thermostat, 200°, Auto, 1/4"

Thermostat, 310°F ± 10°F, Manual, 1/4"

screw, 6 x 3/16, phil pan head, self tapping

sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi

hose, 3/8" x 6.5", (OAL), f x fsw, surge, 1600psi

E573

E574

E519

H274

AH156

AH108S

35

33

34

31

32

30

18

exhaust boot, plastisol

plate, manifold, parallel

bolt, 1/4-20 x 1/2", hex head, zinc

H601

H201

37

36

gasket, vacuum motor

manifold, dual vac, parallel

bolt, 1/4-20 x 3/4" serrated hex flange, zinc

P750

H768

G059

40

39

38

vac support, 3 stage, 4-1/16"

bolt, 1/4-20 x 1/2" serrated hex flange, zinc

H501

H770

C302 vac motor, 3 stage, 120V, tangential

G004

43

44

42

41

C

Part prices are subject to change.Order parts at: www.mytee.com/products/product.php?id=1003DX

clamp, hose, 2-1/4 dia

vac hose, 2", wire reinforced

H217

PH628-20

45

46

pump, 450 psi, 115V 1 $588.99 ea

plug, brass, 3/8" mpt, hex

cuff hose, 2 X 2, wire reinforced

hose, 3/8" x 14-1/2" (OAL), f surge

tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt

B242

B246

H544

C313

AH184

50

49

51

48

47

sol hose, 1/2" kuri 100psi

bushing, brass, 1/2"mpt x 3/8" fpt, hex

elbow, brass, 90 deg, 1/2" barb x 3/8"mpt

adapter, brass, 1/2" barb x 3/8" fsw, ball end

B210

B160

B172

PH615-36

54

55

53

52

B

D

C

B

A

E

F

1003DX

SHEET 2 OF 2

speedster

REV

PRODUCTS, INC.

OD

1

99

97

96

95

94

93

102

101

103

100

104

98

29

105

106

36

6

4

4

77

107

60

to pump "OUT"

thru AH108S (#36)

2

mytee

DATE

10/12/10

NAME

J. Cash

858-679-1191

TITLE:

CHECKED

DRAWN

DO NOT SCALE

DRAWING

DWG. NO.

D

SCALE: 1:6

SIZE

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS PROHIBITED.

1

1003DX SPEEDSTER

2

92

91

89

90

88

85

3

87

86

83

84

4

6

72

71

73

66

4

71

72

39

78

72

52

52

26

to female QD

thru B103 (#6)

71

70

39

69

68

67

42

39

63

to vac tank

thru B111 (#62)

27

28

29

to prime valve

thru B136 (#2)

60

62

59

58

61

to sol tank

55

4

5

6

53

56

57

4

54

53

to sol tank filter

thru B186 (#59)

49

8

52

51

13

50

49

36

16

14

64

6

65

6

to heater "IN"

48

6

to pressure gauge

thru B136 (#2)

35

108

to prime valve

thru B235 (#7)

2

75

4

60

74

74

77

6

4

79

14

to unloader

thru B111 (#62)

2

76

3

13

80

36

66

14

to pump "IN"

thru B160 (#55)

4

3

to heater "OUT"

thru AH108S (#36)

82

55

81

56

81

57

5

6

3

4

5

1

7

8

9

7

10

11

12

13

14

15

16

6

30

7

47

13

36

34

6

31

32

33

17

18

7

21

46

45

44

37

38

39

22

23

24

19

20

43

42

8

40

41

25

8

19

1003DX SPEEDSTER

Circuit Detector

E564

L1a

L2a

White

White / Red

Light 1
Light 2

L2b

L1b

E317

Cooling Fan

White

Black

Pink 18 AWG
Pink 18 AWG

Red

E512B

Lamp Amber

Black

Heater 2

Thermal Switch

GND

Thermal Switch

1000W

White / Red

L1 L2

Black

Orange

Thermal Switch

GND

1000W

Thermal Switch

White / Red

L1 L2

Heater 1

203C203C

Inline Conn.

GND

L2

Black

White/Red

Inline Conn.

L1

Black

Brown

Orange / Black

515E515E

Inline Conn.

Vacuum Motor 2

Inline Conn.

GND

L2

Black

White

Inline Conn.

L1

Black

SW-DPST SW-DPST

Yellow

Vacuum Motor 1

Inline Conn.

E511

E511

C313

White White White

GND

White / Red

L2

L1

Blue

E515

SW-DPST

Orange / Black

Orange Orange

Lamp Heater 2

Lamp Heater 1

13655 Stowe Dr.

Poway, CA

92064

---1

Mytee Products

Revision:

Sheet of1

White / Red White / Red White / Red White / Red

Black

Red

Inline Conn.

Inline Conn.

Black

White

GND

L2

L1

GND

L1

L2

Cord Input Primary

Bottom or Far Left

Entry Location,

Entry Location, Top or Far Right

Cord Input Secondary

Pressure Pump

Black Black Black

Heater Switch

Red Red Red Red Red

Black

E516

3-Position

Red

White Red White / Red

0000 A

Time:

Legal

12/7/2010 10:34:12 AM

C:\Compaines\GHI\Projects\Mytee Schematics\1003DX\1003DX.SCHDOC

1003DX

Date:

File:

Title

Size: Number:

20

1005DX SPEEDSTER

1005DX SPEEDSTER® BACK1005DX SPEEDSTER® FRONT

10

1

2

11

3

4

5

6

7

1. Switch plate

2. 2” Male Cuff-Lynx™

3. Solution lid

4. Female quick disconnect (QD)

5. Front handle

6. Front vent

7. Prime Valve

8. Pressure Regulator

9. Solution tank

10. Recovery lid

1005DX SPEEDSTER® ITEMS INCLUDED

12

13

9

14

17

15

8

11. Push handle

12. Recovery tank

13. Drain valve

14. Back vent

15. Dual Power cords

16

16. 12” Rear wheels

17. 5” locking casters

1005DX SPEEDSTER® CORD

Left cord: Powers power Vac 2.

Right cord: Powers Vac 1 & Pump.

H110 Cuff-Lynx™ H141 Cuff-Lynx™

2” Hose Adapter 2” Hose Reducer to 1.5”

H375- Hose Hanger H226 Drain Elbow

(4) screws

Yellow tag

indicates primary

cord.

Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.

21

Speedster Prime Label

1005DX SPEEDSTER

Speedster Prime Label

1005DX SPEEDSTER® VAC/SOL

HOSE CONNECTIONS

Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® Cuff­Lynx™ vacuum hose port.

1005DX SPEEDSTER® SWITCHES

Vac 1 Vac 2

Pump

“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. Bottom right switch has no use.

1005DX SPEEDSTER® FILL SOLUTION TANK

Lift lid and manually ll the tank.

1003DX SPEEDSTER® PRIME VALVE

1005DX SPEEDSTER® PRIME VALVE

& PRESSURE REGULATOR

& PRESSURE REGULATOR

PRIME POSITION

PRIME POSITION

HIGHER PSI

HIGHER PSI

PRESSURE

PRESSURE
REGULATOR

REGULATOR

LOWER PSI

RUN POSITION

RUN POSITION

Prime the pump by turning the valve to the Prime position (as

Prime the pump by turning the valve to the Prime position (as
shown above) for 30 seconds, then turn right to the Run position.

shown above) for 30 seconds, then turn right to the Run position.
Turn the Pressure Regulator to the left to decrease water pres-

Turn the Pressure Regulator to the left to decrease water pres­sure. Turn the Pressure Regulator to the right to increase water

sure. Turn the Pressure Regulator to the right to increase water
pressure.

pressure.

LOWER PSI

22

1005DX SPEEDSTER

1005DX SPEEDSTER® FILTER MAINTENANCE

INTAKE
FILTER

Check and clean solution tank lter daily by twisting off, rinsing
with clean water and replacing.

1005DX SPEEDSTER® BALL FLOAT

An internal ball oat automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear dump valve.

1005DX SPEEDSTER® DUMP VALVE

& LOCKING CASTERS

Above, empty the recovery tank by attaching the 45˚ drain elbow to
the drain spout in back. Lift up the dump valve and empty the tank.
Below, locking casters help keep the machine remain stationary
during use.

MYTEE® SYSTEM MAINTAINER

Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.

23

1005DX SPEEDSTER

D

C

B

E

F

A

1

2

REV

OD

PRODUCTS, INC.

858-679-1191

SPEEDSTER

mytee

TITLE:

DATE

10/12/10

NAME

J. Cash

CHECKED

DRAWN

SHEET 1 OF 2

1

DO NOT

SCALE DRAWING

1005DX

DWG. NO.

C

SCALE: 1:8

SIZE

2

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS

PROHIBITED.

MSRP

3

$190.99 ea

1

QTY.

4

DESCRIPTION

vac tank, speedster

5

P733

PART NO.

55

NO.

ITEM

MSRP

6

$2.99 ea

2

QTY.

$7.99/ft

$6.99 ea

$11.49 ea

$11.99 ea

1

1

1

pipe, pvc, 2"

elbow, 2" float

gasket, 7", vac lid

P726

P682

G091

59

58

60

$0.99 ea

$0.99 ea

$0.99 ea

2

2

23

$36.99 ea

1

lid, vac tank, black, 7"

G090

61

$3.19 ea

4

$10.99 ea

1

1

inlet, 2"

adaptor, pvc 2, fmsl x fmt

P685

P684

56

57

$0.99 ea

$8.99 ea

1

10

$0.99 ea

6

screw, #8 x 5/8 phil oval, s/s

$4.99 ea

$18.49 ea

$11.49 ea

$141.99 ea

1

1

2

2

float, 2", ball style

sol tank, speedster

connector, cord lock

$3.19 ea

$1.99 ea

2

2

nut, lock, 1/2" steel

fitting, strain relief, cord

power cord, pigtail, 30", 12/3, black

E550

P732

H304

H490

62

63

$0.99 ea

$4.49 ea

7

10

G131

64

65

$0.99 ea

$13.49 ea

17

H220

66

67

$0.99 ea

$23.19 ea

2

2

H221

68

$0.99 ea

18

$9.99 ea

$4.99 ea

$8.99 ea

$13.49 ea

$15.99 ea

$148.99 ea

1

1

6

1

2

2

bracket, rear, fb/spy

gasket, vacuum motor

plate, manifold, parallel

manifold, dual vac, parallel

vac support, 3 stage, 4-1/16"

motor, 3-stage, 115 cfm,14.5 amps

P750

H912

H601

H501

G004

C302A

69

70

71

72

73

74

$6.99 ea

$0.99 ea

$0.99 ea

$0.99 ea

$9.99 ea

$141.99 ea

2

8

1

4

1

13

$8.99/ft

$1.49 ea

1

3

clamp, hose, 2-1/4 dia

vac hose, 2" wire reinforced, gray

$8.99/ft

$2.49 ea

$3.49 ea

$4.99 ea

$12.49 ea

1

2

exhaust boot, plastisol

cuff hose, 2 X 2, wire reinforced

$86.99 ea

1

1

2

1

regulator, 450 psi

sol hose, 1/2" kuri 100 psi

adapter, brass, 1/2" barb x 1/4" mpt

adapter, brass, 1/2" barb x 3/8" fsw, ball end

B644

B160

H544

H217

PH628-24

76

75

$0.99 ea

$41.99 ea

2

2

G059

77

78

$1.99 ea

$6.49 ea

6

1

PH615-22

79

80

$2.49 ea

$0.99 ea

2

10

C313C

81

82

$1.99 ea

$8.99 ea

2

2

$8.99/ft

$8.49 ea

$4.99 ea

$30.49 ea

1

2

1

1

sol hose, 1/2" kuri 100 psi

hose, 3/8" x 10", (OAL), f x f

elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt

elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt

B136

B652

AH103

PH615-10

83

84

85

86

$0.99 ea

$3.49 ea

$31.99 ea

$17.99 ea

1

2

1

3

$8.99/ft

$1.99 ea

$9.49 ea

4

3

plug, brass, 3/8" mpt, hex

elbow, brass, 90 deg, 1/2" barb x 3/8"mpt

B246

B172

87

88

$0.99 ea

$0.99 ea

3

1

$3.19 ea

$13.99 ea

1

$5.49 ea

$588.99 ea

1

1

1

1

tee, brass, 1/4" mpt

pump, 450 psi, 115V

sol hose, 1/2" kuri 100 psi

bushing, brass, 3/8"mpt x 1/4"

tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt

B242

89

$38.99 ea

1

C313

PH615-36

91

90

$9.99 ea

$13.99 ea

4

1

B135

B105

92

93

$0.99 ea

$8.99 ea

1

2

MSRP

3 $26.49

sol hose, 1/4" x 24 1/4"

$74.99 ea

2

QTY.

DESCRIPTION

power corf, ext 50', 12/3 black

AH108S

94

$0.99 ea

$0.99 ea

2

2

E530

PART NO.

Items not shown

$5.49 ea

$3.49 ea

$7.99 ea

$3.99 ea

2

1

1

1

$9.99 ea

$4.99 ea

$3.99 ea

$62.49 ea

1

1

controller, circuit light

filter, bag, vac tank, draw string

$3.99 ea

$10.99 ea

2

1

1

1

hanger, wire forned, hose

cuff-lynx, 2" to 1.5" reducer

gasket, strip, 3/4" x 36" x 1/8"

cuff-lynx, female swivel x female thread 2"

E564

$7.99/ft

G010

G085

$1.99 ea

$0.99 ea

8

16

H140

$6.99 ea

$3.99 ea

2

1

H141

H375

$2.49 ea

$15.99 ea

1

1

$3.19 ea

$20.99 ea

1

3

4

5

6

7

DESCRIPTION

guard, cooling fan, wire

screw, #10 x 5/8" hex head zinc

8

H296

H343

PART NO.

1

2

NO.

ITEM

washer, 1/4" flat, s/s

washer, 1/4" lock, s/s

bracket, front hinge, sp/fb

nipple, brass, 1/4"m, hex

washer, 9/16"id x 1"od, flat, s/s

bolt, 1/4-20 x 1/2", hex head, zinc

elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt

B107

H201

6

B103

H212

7

8

9

H378

3

H210

4

F

H213

5

caster, 5"

ball valve, 1/4'' 1

nut, lock, 1/4-20 nylon insert

B656

H216

10

11

handle, breeze and dx

washer, 1/4"id x 1"od, flat, s/s

bolt, 1/4-20 x 3/4" hex head, s/s

bolt, 1/4-20 x 1-1/2" hex head, s/s

H316

H666

H202

H485

H211

12

13

14

15

16

E

bolt, 1/4-20 x 3/4" serrated hex flange, zinc

H768

17

base, speedster

P731

18

wheel, 12"

axle, 18.25" x .50" dia

washer, axle, cut 1/2" id

H254

H371

H251

H219 cap, axle, 1/2"

19

20

21

22

filter, strainer, 1/2"

qd, brass, 1/4" f

nipple, brass, 3/8" x close

washer, buna 1-1/8" od x 3/16" id

washer, 11/16"id x 1-1/2"od x .075, s/s

bushing, brass, 1/2"mpt x 3/8" fpt, hex

elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt

adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex

B210

B216

B186

B102

G052

23

D

B119A

24

H299

25

26

B111

28

29

30

27

24

washer, #8 flat, s/s

hose, 3/8" x 24 1/2", (OAL)

AH105

31

gauge, pressure, 2000 PSI

screw, #10-32 x 1/2" SHCS, alloy

screw, 8-32 x 3/8" SHCS, alloy, Black

H246

H612

H389

H308D

32

33

34

35

C

nut, kep, #10-32 zinc

switch, rocker, 2 position

light, indicator, 125v (amber)

plate, switch, sp, 4 hole w/gauge

E515

H273

H337

E512B

36

37

39

38

filter, strainer, 1/4"

nut, hex, 1/4-20 s/s

bolt, 1/4-20 x 1-1/4" hex head

B119

H215

H203

40

41

42

B

sol hose, kuriyama, 3/8" 1

clamp, hose, 5/16-29/32

nipple, brass, 1/4" x close

adapter, brass, 3/8" barb x 1/4" fsw

45 deg, street elbow, brass, 1/4" male NPTF

B130

B106

43

44

bolt, 1/4-20 x 1/2" serrated hex flange, zinc

B235

H347

H770

PH715-28

47

45

46

48

Part prices are subject to change.Order parts at: www.mytee.com/products/product.php?id=1005DX

gasket, 2" inlet

valve, drain, 1-1/2" 1

spout, drain, 45 degree

elbow, inlet assembly 2"

bracket, "L" (all extracters)

Cuff-Lynx, 2" m cuff x 2" mpt

H226

G083

51

A

A926

52

H225

54

53

H390A

49

H135

50

7

8

1005DX SPEEDSTER

F

1

62

61

2

3

4

E

59

60

58

63

D

54

55

57

56

To pump "OUT"

64

*

53

thru AH108s

(#96)

C

52

49

42

41

39

9

38

37

9

7

8

8

30

29

To pump "IN"

36

35

34

32 33

31

thru PH615-36

(#92)

51

43

8

16

23

28

50

48

44830

23

16

40

8

7

To regulator

thru PH615-22

(#82)

26

27

B

45

To pump "OUT"

thru AH108S

(#96)

8

26

26

26

26

25

A

REV

OD

SHEET 2 OF 2

1

PRODUCTS, INC.

858-679-1191

SPEEDSTER

47

45

To ball valve

thru B107

(#7)

mytee

TITLE:

DATE

7/1/2010

NAME

J. Cash

DRAWN

CHECKED

46

DO NOT

SCALE DRAWING

1005DX

DWG. NO.

C

SCALE: 1:8

SIZE

2

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS

PROHIBITED.

3

4

24

17

23 16

15

22

21

20

19

18

17

16

15

4

(#87)

8

B

13

14

7

8

9

10

9

A

11

4

12

1

2

C

11

To regulator

thru AH103

3

5

4

6

7

To vac tank

thru B235

(#45)

5

6

7

8

90

90

89

4

D

65

66

86

To ball valve

thru B107

(#7)

11

67

68

69

70

48

48

83

84

85

30

88

5

71

14

73

96

72

To sol tank "IN"

thru B186

(#28)

81

96

86

To q.d.

thru AH105

(#31)

E

4

17

82

81

To sol tank

thru B186

(#28)

87

47

92

9

95

96

9

91

90

14

94

4

93

2

17

77

78

6

79

77

7

To pressure guage "OUT"

thru B103

(#9)

8

F

74

76

80

25

1005DX SPEEDSTER

Circuit Detector

E564

L1a

L2a

White

White / Red

Light 1
Light 2

L2b

L1b

Black

Pink 18 AWG
Pink 18 AWG

E512B

Lamp

Amber

Red

13655 Stowe Dr.

Poway, CA

92064

---1

Mytee Products

Revision:

Sheet of1

Black

0000 A

Time:

Letter

11/30/2010 11:52:30 AM

1005DX

Title

Vacuum Motor 2

C302AC302AC313

Inline Conn.

White

GND

Green

L2

Black

L1

BlackBrown

515E515E

C:\Compaines\GHI\Projects\Mytee Schematics\1005DX\1005DX.SCHDOC

Size: Number:

Date:

File:

Inline Conn.

Inline Conn.

GND

Green

White

L2

Black

Inline Conn. Inline Conn.

L1

SW-DPST SW-DPST

Yellow Black

Vacuum Motor 1

Inline Conn.

E515

White White White

Green Green

Green Green

Green

White / Red White / Red White / Red White / Red

GND

L2

White

L1

Pressure Pump

Black

SW-DPST

Blue

Black Black Black

Red Red Red Red Red

Red

Inline Conn.

Black

GND

L2

L1

L1

Entry Location, Top or Far Right

Cord Input Primary

Inline Conn.

White

GND

L2

Bottom or Far Left

Entry Location,

Cord Input Secondary

26

GENERAL INFORMATION

Dear Customer:

Congratulations on the purchase of your new Speedster® Extractor. As
you are already aware, the scene of the equipment world is becoming
more high tech, and we at Mytee Products Inc. strive to keep you on the
cutting edge with superior quality and technology.

Keep in mind that the Speedster® Extractor is a machine, so neglect or
abuse will cause unnecessary damage and void the warranty. However
with simple maintenance the Speedster® will give quality performance for
many years to come.

If warranty questions arise, please consult user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts
or ordering parts, please call an authorized Mytee Products Inc. Service
Center. To see an updated list, visit our website at www.mytee.com

Before you begin using, please read your manual thoroughly.

Sincerely,
Mytee Customer Care Dept.

Grounding Instructions

This machine must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electrical shock. This ma­chine is equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed in accordance with all local code and ordinances.
Do not remove ground pin; if missing, replace plug before use.

Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualied electrician or service person
if you are in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the machine. If it will not t the outlet, have a
proper outlet installed by a qualied electrician.

This appliance is for use on a nominal 120-volt circuit, and has a ground­ing plug that looks like the plug illustrated in Figure 1 below. A temporary
adapter illustrated in Figures 2 and 3 may be used~to connect this plug to
a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is
not available. The temporary adapter should be used only until a properly
grounded outlet (Figure 1) can be installed by a qualied electrician. The
green colored rigid ear, tab or the like extending from the adapter must be
connected to a permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place by a metal
screw. Grounding adapters are not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

The Green (or GreenYellow) wire in the cord is the grounding wire. When
replacing a plug, this wire must be attached to the grounding pin only.

DO NOT use extension cords.
Please Note for America use only

Grounding Pin

Figure 1

Grounded Outlet

Metal
Screw

Grounded Outlet Box

Figure 2 Figure 3

Adapter

Tab for Grounding
Screw

Parts and Service

Repairs, when required, should be performed by Mytee service person­nel or Mytee authorized Service Center using Mytee original replacement
parts and accessories. Call Mytee for repair parts or service. Please

specify the Model and Serial Number when discussing your machine.

Name Plate

The Model and Serial Number of your machine are shown on the name
plate located on the inside of the machine. This information is needed
when ordering repair parts for the machine. Use the space provided on
the front cover to note the Model and Serial Number of your machine for
future reference.

Unpacking the Machine

When the machine is delivered, carefully inspect the shipping carton and
the machine for damage. If damage is evident, save the shipping carton so
that it can be inspected by the carrier that delivered it. Contact the carrier
immediately to le a freight damage claim.

Caution and Warnings

Symbols

Mytee uses the symbols below to signal potentially dangerous conditions.
Always read this information carefully and take the necessary steps to
protect personnel and property.

Is used to warn of immediate hazards that will cause severe personal
injury or death.

Is used to call attention to a situation that could cause severe personal
injury.

Is used to call attention to a situation that could cause minor personal
injury or damage to the machine or other property. When using an electri­cal appliance, basic precautions should always be followed, including the
following: Read all instructions before using this machine. This product is
intended for commercial use only.

To reduce the risk of re, electrical shock, or injury:

1. Read all instructions before using equipment.

2. Use only as described in this manual. Use only manufacturer’s recom­mended attachments.

3. Always unplug power cord from electrical outlet before attempting any
adjustments or repairs.

4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord.

5. Do not pull or carry by cord. Do not close a door on cord or pull cord
around sharp edges or corners.

6. Do not run appliance over cord. Keep cord away from heated surfaces.

7. Do not use with damaged cord or plug. If cord is damaged, repair im­mediately.

8. Do not use outdoors or on wet surfaces and or standing water.

9. Always unplug or disconnect the appliance from power supply when not
in use.

10. Do not allow to be used as a toy. Close attention is necessary when
used by or near children.

11. Do not use in areas where ammable or combustible material may be
present.

12. Do not leave the unit exposed to harsh weather elements. Tempera­tures below freezing may damage components and void warranty.

13. Use only the appropriate handles to move and lift unit. Do not use any
other parts of this machine for this purpose.

14. Keep hair, loose clothing, ngers, and all parts of the body away from
all openings and moving parts.

15. Use extra care when using on stairs.

16. To reduce the risk of re or electric shock, do not use this machine with
a solid-state speed control device.

27

GENERAL INFORMATION

17. The voltage and frequency indicated on the name plate must corre­spond to the wall receptacle supply voltage.

18. When cleaning and servicing the machine, local or national regulations
may apply to the safe disposal of liquids which may contain: chemicals,
grease, oil, acid, alkalines, or other dangerous liquids.

19. Do not leave operating unattended.

Preparation

1. Remove furniture and other items from the area you are going to clean.

2. Vacuum carpet and upholstery, and remove debris.

3. Protect cabinets, walls and painted surfaces with drop cloths or plastic.

4. Inspect power cords for damages.

Operating Instructions

1. Fill the solution tank.

2. Attach one end of a solution hose to a wand or other tool, the other end
to the Speedster’s® front quick disconnect.

3. Attach one end of a vacuum hose to the tool, the other end to the
Speedster’s® Cuff-Lynx™ vacuum hose port.

4. Plug in power cords.

• 1000DX and 1000DX-200 models – Plug single cord into single, 20A
grounded wall outlet.

• 1001DX, 1001DX-200 models – Using two separate circuits/breakers,
plug the left power cord into 20A grounded wall outlet to turn on Vac 2 and
Heater 2. Plug the right power cord into separate 20A grounded wall outlet
to turn on Vac 1, Heater 1 and Pump.

• 1003DX models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2 and Heater 2.
Plug the right power cord into separate 20A grounded wall outlet to turn on
Vac 1, Heater 1 and Pump.

• 1005DX models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2. Plug the right
power cord into separate 20A grounded wall outlet to turn on Vac 1 and
Pump.
The amber light indicator on the switch plate will illuminate brightly when
cords are plugged into two separate circuits. Do not use extension cords
longer than 50 feet.

5. Turn on switches.

• 1000DX, 1000DX-200, 1005DX models – Turn on Vac 1, Vac 2 and
Pump switches.

• 1001DX, 1001DX-200 and 1003DX – Turn on Vac 1, Vac 2 and Pump
switches. Turn on Heater switch if heat is being used. Wait several
minutes for water to heat. Heater switch has three positions: Off (middle);
1,000 watts using one heater (left); and 2,000 watts using two heaters
(right). Red lights on panel display indicate watts selected: one light =
1,000 watts; two lights = 2,000 watts; no lights = heaters are off.

6. 1003DX and 1005DX models – Prime Valve and Pressure Regulator
are located on the lower front of the extractor. To prime the pump, turn the
valve to the Prime position for 30 seconds, then turn horizontally to the
Run position. Turn the Pressure Regulator to the left to decrease the water
pressure. Turn to the right to increase water pressure. Level will be visible
on the pressure gauge. Monitor while adjusting, using Pressure Gauge on
Switch Panel.

7. Begin cleaning. Make two dry passes to every wet pass. Work away
from cords to avoid damage. To clean heavily soiled areas, repeat clean­ing from a different direction.

8. Use a foam control solution in the recovery tank to prevent motor dam­age and check for foam build-up in recovery and solution tanks.

9. Empty the recovery tank as needed when the internal ball oat auto­matically shuts off the vacuum. Attach the 45˚ drain elbow to the drain
spout in back. Lift up the dump valve and empty tank.

10. To relieve water pressure from the solution hose before disconnecting
it, squeeze the tool’s trigger ve seconds after turning the power switches
off.

11. Once machine is off, unplug power cords. Remove solution and
vacuum hoses. Empty the recovery tank by attaching the 45˚ drain elbow
to the drain spout in back. Lift up the dump valve and empty tank.

12. 1003DX and 1005DX models – Water remaining in the solution tank
can be emptied by turning the Prime Valve to the right to move water into
the recovery tank. Empty recovery tank.

After Use

1. Before storing machine, drain, rinse and dry tanks and vacuum hose of
water and solution.

2. Store in a dry are in the upright position.

3. Open recover tank cover to promote air circulation.

4. Store indoors in a dry area. If storing in freezing temperatures, make
sure the machine and solution system are completely drained and dry.

Maintenance Schedule

Latches are located in back to open tank for internal maintenance. To
keep machine in good working condition, follow machine’s daily and
weekly maintenance procedures. Check valves and relief valves should be
replaced annually.

Maintenance item Daily Once a week

Clean and inspect tanks.
Clean and inspect hoses.
Check and clean internal lters by twisting
off, rinsing with clean water and replacing.
Check power supply cable.
Clean machine with all-purpose cleaner
and cloth.
Check spray nozzles.
Flush solution system with Mytee® System
Maintainer.
Remove and oat shut-off screen from
tank and clean. Simply pull off.
Inspect vacuum hoses for holes and loose
cuffs.
Inspect spray pattern for clogging. If
clogged, remove spray tips and soak them
in a recommended liquid neutralizer for
up to six hours. To remove spray tip, twist
spray tip body counter-clockwise.
Lubricate wheels with water resistant oil.
Inspect machine for water leaks and loose
hardware.

x
x
x

x
x

x

x

x

x

x

x
x

Trouble Shooting

There is no power.

1. Plug machine in proper outlet.

2. If using two cords, make sure each is plugged into a separate circuit.

3. Check circuit breaker. Reset circuit breaker, other items should not run
on the same circuit as the machine. Outlet must be a 20-amp circuit.

Pump does not work properly

1. Snap quick disconnects rmly together.

2. Check solution tank; may be empty.

3. Jets clogged, remove jet and ush clean.

4. Filters clogged, remove lters and rinse clean with water.

5. Heater is blocked; ush out with Mytee’s® System Maintainer.

6. If brass check valve is stuck, replace valve.

7. Check pump wire. May need to reconnect wire.

8. Switch plate may need to be replaced.

9. If pump motor brushes are worn, replace pump.

1001DX, 1001DX-200 or 1003DX heater does not work properly

1. If sensor mounted on the heater has popped, reset sensor by pushing
in button.

2. Heating element may need to be replaced.

Vacuum motor does not work properly

1. Check that hose is tightly connected.

2. Close drain hose valve completely.

3. Secure the vacuum tank tightly.

4. If ball oat is shut off, empty vacuum tank of all wastewater.

5. Make sure ball oat is rmly installed on the elbow.

6. If water is coming out of the vacuum motor, use a low foaming
detergent.

7. Clean upholstery tool or oor wand jets.

28

GENERAL INFORMATION

FAQs

Q: How much do the Speedster® Series extractors weigh and what are
the dimensions?
A: All Speedsters
Machine Dimensions: 28” x 18 ¼” x 40”
Shipping Dimensions: 29 ½” x 19 ¼” x 46 ½”

1000DX – Machine Weight: 83 lbs.
Shipping Weight: 104 lbs.

1000DX-200 – Machine Weight: 83 lbs.
Shipping Weight: 104 lbs.

1001DX – Machine Weight: 94 lbs.
Shipping Weight: 124 lbs.

1001DX-200 – Machine Weight: 94 lbs.
Shipping Weight: 124 lbs.

1003DX – Machine Weight: 122 lbs.
Shipping Weight: 150 lbs.

1005DX – Machine Weight: 113 lbs.
Shipping Weight: 140 lbs.

Q: What comes standard with Speedsters™ extractors?
A: Hose hanger with four screws, two Cuff-Lynx™ Model Numbers: H141
Reducer and H110 Coupler Swivel, and 45˚ drain elbow.

Q: Does Mytee® recommend tools for this machine?
A: All upholstery tools and wands can be used with the Speedster® series.

Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow
excess moisture in the vacs to dry off. You should also run Mytee’s®
System Maintainer through the system to keep the hoses, pump, and
heater clean and free of debris..

Warranty

MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and
product support to its customers and therefore backs up all of its new
products purchased from Mytee Products Inc. (“Mytee”) or any authorized
Mytee distributor/service center with this lifetime limited warranty. This
limited warranty begins on the date of the customer’s purchase and is
valid and available to the original purchaser with proof of purchase, and is
not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.

HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that
its rotationally-molded housings will be free from manufacturing defects.
This warranty covers the cost of replacement or repair only and does not
cover shipping or labor costs.

WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear
parts for 90 days from the date of original purchase. “Wear parts” are
items which wear out as a result of usage or the passage of time and are
consumed despite attempts to maintain them, such as gaskets, wheels,
brass, cords, wires, electrical terminals, hoses, switches, thermostats,
plastisol parts, lters, bearings, brushes, solenoids, o-rings, bulbs, heat­ing elements, castors, or other parts deemed wear items in Mytee’s sole
discretion. This warranty covers the cost of replacement only and does not
cover shipping or labor costs.

HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO
WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUAL­ITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE,
PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY
GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRAN­TIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE

HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME
FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE
SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY
BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT
NOTICE.

LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR
REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE
REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER
EXPRESS OR IMPLIED. IN NO EVENT SHALL MYTEE BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY
DAMAGES, OR PERSONAL INJURIES.

All limited warranties are void for, and Mytee does not warrant in any way,
any product that evidences misapplication, improper installation, abuse,
lack of maintenance, negligence in use or care, abnormal use, alteration
of design, modication, use of incompatible or corrosive chemicals, use in
a rental service, and/or servicing, installation of parts, or repairs by anyone
other than Mytee or a Mytee authorized distributor or service center. Mytee
may make changes in products it manufactures and markets at any time;
these changes are made without obligation to change, retrot, or upgrade
any product previously sold or manufactured.

Mytee has no obligation to honor the limited warranties set forth herein
unless the original purchaser, promptly upon discovering the warranty
claim and prior to continuing to use the product, contacts Mytee or a
Mytee authorized distributor or service center to describe the claim and to
receive and follow instructions for documenting and resolving the claim.
In addition, the purchaser must provide the product to which the claim
applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the
product intact, unmodied, with all of its original parts.

If any provision or portion of this limited warranty policy is found to be
unenforceable, then the remaining provisions and portions shall remain
valid and enforceable. If any provision or portion of this limited warranty
policy is found to be limited by law, then that provision or portion shall
be construed to make it effective within the bounds of law. For example,
if there are legal limitations on the duration of warranties, the warranties
made herein shall be construed to have the minimum duration required by
law, or, if there are legal limitations of exclusion of remedies, the exclu­sions made herein shall be construed to apply to the fullest extent possible
without violating the law.

The validity, construction and performance of this warranty policy shall be
governed by the laws of the State of California, without respect to conicts
of laws principles. The exclusive jurisdiction of any legal action arising
from or related to this warranty policy shall be in the State of California and
no legal action shall be commenced elsewhere.

Return Material Authorization Procedure

It is the responsibility of any Authorized Service Center (ASC) or Dis­tributor with written authorization to ensure the Customers equipment is
repaired as soon as possible. Only Mytee Products Inc. or it’s authorized
dealers with written authorization, service centers, and agents may make
warranty repairs on these products. All others do so at their own risk and
expense.

The Distributor must follow Mytee Products, Inc. standard RMA procedure:

1. When a repair falls within the Warranty time period for a piece of equip­ment, the Distributor will ll out a RMA/Warranty claim form. This form will
act as a repair order to replace any defective parts.

2. All defective parts must be returned to Mytee Products, Inc. with the
RMA/claim form for evaluation at the customer’s expense. This shipping is
non-refundable. All warranty claims are subject to an evaluation by Mytee
Products, Inc. to determine if warranty will be approved. Any credit for

29

repair and/or parts will only be issued upon evaluation and approval from
Mytee Products, Inc.

3. When Warranty is approved, the Distributor’s account will be credited
for the replacement part(s). Mytee Products, Inc. will ship the warranted
replacement part(s) to the Distributor prepaid. If Warranty is denied the
Distributor’s account will not be credited for any parts sent for this claim.

NOTES

30

NOTES

31

Mytee Product s I nc.
13655 Stowe Dr.
Poway, Ca. 920 64

www.my tee.com
PH 85 8.679.1191
F X 858.6 79.7814

© 2010 M ytee Pro du cts Inc.
Print ed in t he U.S.A.

32