Mytee S-300 TEMPO Instructions Manual

Download

Page 1

Instructions for

S-300 Tempo

Please read before use.

™

Set up p. 2 How to p. 4 General information p.14

Model #

Serial #

Form # ADM-Tempo

1-14

13655 Stowe Dr., Poway, Ca. 92064

Page 2

Page 3

S-300 TEMPO™

1. Handle

2. Solution Tank Lid

3. 3” Wheels

4. Solution Tank

FRONT

5. Recovery Tank

6. Recovery Tank Lid

BACK

7. Vacuum Hose Hook Up

8. Recovery Tank Drain Cap

9. Quick Disconnect

10. Power Switch

11. 25’ Power Cord

ACCESSORY

8’ vacuum and solution hose combo.

VACUUM AND SOLUTION

HOSE CONNECTION

Located at the back of the Tempo™, attach the male end of the solution hose to the Tempo’s™ QD. Then connect the vacuum hose to the Tempo’s™ hose port.

Page 4

S-300 TEMPO™

FILL SOLUTION TANK

Twist off solution tank lid and ll with water. For best results, ll with warm water (140o F).

POWER SWITCH

Plug machine’s cord into a grounded wall outlet then switch power on. FOR SAFETY: Do not operate machine unless cord is properly grounded.

EMPTY RECOVERY TANK

To empty the recovery tank, remove cap located above the quick disconnect to releases uid.

Page 5

S-300 TEMPO™

FILTER

To get the best performance out of the Tempo™, after each job, twist off the recovery tank lid and clean off the lter located on the vacuum stack.

DEFOAMER

Add defoamer in the recovery tank to reduce foam and prolonging the life of the Tempo’s™ vacuum motor .

SYSTEM MAINTAINER

Weekly ushing of the solution system with Mytee System Maintainer helps keep lines clean and prevents chemical buildup, improving pump life, performance and pressure.

Page 6

S-300 TEMPO™ PARTS & PRICING

PRODUCTS, INC.

858-679-1191

Spotter

mytee

TITLE:

DATE

4/5/11

NAME

J. Cash

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

CHECKED

DRAWN

REV

SHEET 1 OF 2

DO NOT

SCALE DRAWING

S-300

DWG. NO.

SCALE: 1:2

SIZE

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS

PROHIBITED.

ACCESSORIES

MSRP

$3.99 ea

QTY.

DESCRIPTION

cu-lynx, 2" to 1.5" reducer

stop sign register your product

H141

AD127

PART NO.

MSRP

$4.99 ea

$0.99 ea

$13.99 ea

QTY.

$8.49 ea

$3.49 ea

$36.99 ea

$19.99 ea

$17.99 ea

$98.99 ea

strap, velcro, w/buckle

quick disconnect, male, 1/4" male x 1/4" fpt

B101

G147

$1.49 ea

$49.99 ea

vac hose, 1-1/4" x 8' 1

tool, uph, s/s w/ valve

sol hose, 1/8" x 97", (OAL), m

quick disconnect, 1/4" female x 1/4" fpt

B102

H360

H282

AH135

$5.99 ea

$13.99 ea

$0.99 ea

$1.99 ea

$0.99 ea

$3.19 ea

$1.49 ea

$35.49 ea

$99.99 ea

$20.99 ea

$0.99 ea

$3.99 ea

$6.49 ea

$1.75 ea

$2.99 ea

$ 0.99 ea

$1.99 ea

$41.99 ea

$0.99 ea

$4.99 ea

$7.49 ea

$1.99 ea

$9.99 ea

$0.99 ea

$17.99 ea

$29.99 ea

$8.99 ea

$59.99 ea

$4.49 ea

$0.99 ea

$0.99/ft

$0.99 ea

$3.49 ea

$3.99 ea

DESCRIPTION

screw, #8 x 5/8 phil oval, s/s

H304

PART NO.

NO.

ITEM

wheel, 3"

sol tank, spotter

gasket, vac lid, 3.5", clear

bolt, 5/16" shoulder x 1-1/2" lg, alloy

H358

G039

P728A

H650

G030 lid, vac tank, 3.5", clear

nut, lock, 1/2" steel

nut, kep, #10-32 zinc

plate, switch, spotter

switch, rocker, 2 position

E515

H410

H273

H221

washer, #8 at, s/s

screw, #10-32 x 1/2" SHCS, alloy

H612

H389

gasket, vacuum motor

tting, strain relief, cord

power cord, end, 25', 16/3

screw, #8-32 x 3/8" SHCS, alloy

E533

H246

H220

G004

lter, strainer, 1/4"

washer, 1/4" at, s/s

washer, 1/4" lock, s/s

plate, vac. mounting, spotter

vac motor, 2 stage, 115V, peripheral

H213

H646

H210

C316

sol hose, 1/4" kuri 150psi

bolt, 1/4-20 x 1" hex head, s/s 3

adapter, brass, 1/4" barb x 1/4" mpt

B119

B109

H342

PH634-8

washer, 3/8 at, s/s

pump, 55psi, 115V ojet

tting, 1/4" barb x 1/8" FPT

B131

H384

bracket, set 55 psi pump

screw, 10-32 x 1/2 phil pan

nipple, hex, 1/8" mpt x 1/8" mpt

B129

H250

H230

C378

qd, brass, 1/4" f

vac tank, spotter

vac tank deector

tubing, 1/4", nylon black

tting, brass, 1/4"mpt x 1/4" push-in

connector, 1/4" tube push-in x 1/8" mpt

B140

B102

B166

H212 washer, 9/16"id x 1"od, at, s/s

PH657-8

lter strainer, spotter

plate, base & qd, spotter

H898

H664

G058

P728B

pipe, pvc, 3/4"

adapter, pvc, 3/4"

H645 pvc, 90, 3/4"

H644

PH610-2.5

Part prices are subject to change.Order parts at: www.mytee.com/products/product.php?id=8901

nut, brass, 3/4", lock 1

cap, 2.5" threaded, tethered

B653

G036

Page 7

S-300 TEMPO™ PARTS & PRICING

PRODUCTS, INC.

858-679-1191

Spotter

mytee

TITLE:

DATE

4/5/11

NAME

J. Cash

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

CHECKED

DRAWN

REV

SHEET 2 OF 2

DO NOT

SCALE DRAWING

S-300

DWG. NO.

SCALE: 1:4

SIZE

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS

PROHIBITED.

Inside sol tank

26 25

2119

Page 8

GENERAL INFORMATION

Dear Customer:

Congratulations on the purchase of your new Tempo™ spotter. As you are already aware, the scene of the equipment world is becoming more high tech, and we at Mytee Products Inc. strive to keep you on the cutting edge with superior quality and technology.

Keep in mind that the S-300 Tempo™ is a machine, so neglect or abuse will cause unnecessary damage and void the warranty. However with simple maintenance the S-300 will give quality performance for many years to come.

If warranty questions arise, please consult your user manual or get in touch with your distributor. If you have questions about maintenance, replacing parts or ordering parts, please call an authorized Mytee Products Inc. Service Center. To see an updated list, visit our website at www.mytee.com

Before you begin cleaning, please read your manual thoroughly.

Sincerely, Mytee Customer Care Dept.

Grounding Instructions

This machine must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical shock. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed in accordance with all local code and ordinances. Do not remove ground pin; if missing, replace plug before use.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualied electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the machine. If it will not t the outlet, have a proper outlet installed by a qualied electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a qualied electrician. The green colored rigid ear, tab or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. Grounding adapters are not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing a plug, this wire must be attached to the grounding pin only.

DO NOT use extension cords.

Please Note for America use only

Grounding Pin

Figure 1

Grounded Outlet

Metal Screw

Grounded Outlet Box

Figure 2 Figure 3

Adapter

Tab for Grounding Screw

Parts and Service

Repairs, when required, should be performed by Mytee service personnel or Mytee authorized Service Center using Mytee original replacement parts and accessories. Call Mytee for repair parts or service. Please specify the Model and Serial Number when discussing your machine.

Name Plate

The Model and Serial Number of your machine are shown on the Nameplate on the back panel of the machine. This information is needed when ordering repair parts for the machine. Use the space provided on the front cover to note the Model and Serial Number of your machine for future reference.

Unpacking the Machine

When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected by the carrier that delivered it. Contact the carrier immediately to le a freight damage claim.

Caution and Warnings

Symbols

Mytee uses the symbols below to signal potentially dangerous conditions. Always read this information carefully and take the necessary steps to protect personnel and property.

Is used to warn of immediate hazards that will cause severe personal injury or death.

Is used to call attention to a situation that could cause severe personal injury.

Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property. When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using this machine. This product is intended for commercial use only.

To reduce the risk of re, electrical shock, or injury:

1. Read all instructions before using equipment.

2. Use only as described in this manual. Use only manufacturer’s recommended attachments.

3. Always unplug power cord from electrical outlet before attempting any adjustments or repairs.

4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp edges or corners.

6. Do not run appliance over cord. Keep cord away from heated surfaces.

7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.

8. Do not use outdoors or on wet surfaces and or standing water.

9. Always unplug or disconnect the appliance from power supply when not in use.

10. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

11. Do not use in areas where ammable or combustible material may be present.

12. Do not leave the unit exposed to harsh weather elements. Temperatures below freezing may damage components and void warranty.

13. Use only the appropriate handles to move and lift unit. Do not use any other parts of this machine for this purpose.

14. Keep hair, loose clothing, ngers, and all parts of the body away from all openings and moving parts.

15. Use extra care when cleaning on stairs.

16. To reduce the risk of re or electric shock, do not use this machine with a solidstate speed control device.

17. The voltage and frequency indicated on the name plate must correspond to the wall receptacle supply voltage.

18. When cleaning and servicing the machine, local or national regulations may apply to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids.

19. Do not leave operating unattended.

Filling the Solution Tank

1. Fill the solution tank with the approved cleaning solution.

2. Do not ll up the solution tank completely: 1” should be left free at the top.

3. Typically, the solution should be a mixture of water and a cleaning chemical appropriate for the type of job.

4. Always follow the dilution instructions on the chemical container label.

5. The temperature of the cleaning solution must not exceed 70

Use only non-ammable liquid in this machine.

C/160oF.

Page 9

GENERAL INFORMATION

Setup

1. Fill solution tank with water or approved cleaning agent. For best results, ll with warm water (140

). Replace vacuum tank.

Flammable materials can cause an explosion or re. Do not use ammable solutions or materials in tank(s).

FOR SAFETY: When using machine, follow mixing and handling instructions on chemical containers.

ATTENTION: If using powdered cleaning chemicals, mix prior to adding.

2. Attach solution hose (located front of machine). NOTE: Make sure the quick disconnect snap together rmly. As you do this, always inspect hoses for cracks or fraying. Do not use if hoses are damaged.

3. Attach vacuum hose to recovery tank.

4. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate machine unless cord is properly grounded. FOR SAFETY: Do not operate machine with the use of an extension cord.

5. Turn on power. Key tool until you have a steady ow.

6. Re-key upholstery tool until hot water begins owing.

7. Begin cleaning. Make two dry passes to every wet pass.

8. Work away from cords to avoid damage.

9. Use a defoamer in your recovery tank.

10. To clean heavily soiled areas, repeat cleaning from different directions.

11. When vacuum tank is full, empty tank.

12. When work is complete, unplug cords and hoses.

13. Wrap and clean hoses. Clean all tanks.

Pre-Operation

1. Vacuum carpet and upholstery and remove other debris.

2. Perform machine setup procedures.

3. Inspect power cord for damage.

Operation

1. Turn power switch on.

2. Pull up on tool lever to release air in the line. Hold lever until a steady ow of water comes out of the upholstery tool. Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.

1. Work away from outlet and power cord to prevent cord damage.

2. Use a recommended foam control solution in the recovery tank to prevent vacuum motor damage. Periodically check for excessive foam buildup in solution tank, and recovery tank.

3. To clean heavily soiled areas, repeat cleaning path from different direction.

4. When vacuum tank is full, it is time to empty the dirty water from the recovery tank, and rell solution tank.

5. After cleaning, relieve water pressure from tool before disconnecting hose. Squeeze trigger for ve seconds after turning main power switch off.

After Use

1. Unplug.

2. Empty solution tank and rinse it with clean water.

3. Inspect hoses and replace if damaged.

4. Attach 45 recovery tank. 5 Inspect solution lter. Clean or replace if damaged.

6. Store the machine in a clean, dry place.

7. Open recovery tank cover to promote air circulation.

8. Do not expose to rain. Store indoors.

drain elbow to dump valve and lift up drain valve lever to empty

Maintenance Schedule

Maintenance item Daily Once a week

Clean and inspect Tanks Clean and inspect Hoses Check power supply cable Clean machine with all purpose cleaner and cloth Check spray nozzles Flush solution system with Mytee system maintainer Remove and clean oat shut-off screen from tank Inspect vacuum hoses for holes and loose cuffs Inspect machine for water leaks and loose hardware

x x x x

x x x x x

Trouble Shooting

There is no power.

1. Plug machine in proper outlet.

2. Check circuit breaker; reset circuit breaker, other items should not run on the same circuit as machine. Outlet must be a 20-amp circuit.

Pump does not work properly.

1. Snap quick disconnects rmly together.

2. Check solution tank; may be empty.

3. Jets clogged, remove jet and ush clean.

4. Filters clogged, remove lters and rinse clean with water.

5. If brass check valve is stuck replace valve.

6. Check pump wire. May need to reconnect wire.

7. Switch plate switch may need to be replaced.

8. If pump motor brushes are worn, replace pump.

Vacuum motor does not work properly.

1. Check that hose is tightly connected.

2. Close drain hose valve completely.

3. Check and clean foam lter located in recovery tank.

4. If water is coming out of vacuum motor, use a low foaming detergent.

5. Clean upholstery tool.

FAQs

Q: How much does the S-300 weigh and what are the dimensions?

A: 20 Pounds - Dimensions are: 20” x 10” x 16 1/2”. Shipping weight is 23 lbs. and shipping dimensions are 19” x 10 3/4” x 20”

Q: What comes standard with the S-300?

A: The S-300 comes with 8’ Vacuum/Solution Hose with a 4” Stainless Steel Upholstery Tool attached.

Q: Where do I plug the machine in?

A: The S-300 requires a 20A grounded circuit. Please note: GFI outlets may trip before the breaker setting.

Q: Is there anything I can do to increase the expected life of my machine?

A: Running the vacuum motors with the tank empty and lid off will allow excess moisture in the vacs to dry off. You should also run a System Maintainer through the system to keep the hoses, pump, and heater clean and free of debris.

Warranty

MYTEE LIFETIME LIMITED WARRANTY POLICY Mytee Products, Inc. endeavors to provide high quality products and product support to its customers and therefore backs up all of its new products purchased from Mytee Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this lifetime limited warranty. This limited warranty begins on the date of the customer’s purchase and is valid and available to the original purchaser with proof of purchase, and is not transferable. Mytee’s products are for commercial use only and are not intended for personal, family or household uses.

HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotationally-molded housings will be free from manufacturing defects. This warranty covers the cost of replacement or repair only and does not cover shipping or labor costs.

WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for 90 days from the date of original purchase. “Wear parts” are items which wear out as a result of usage or the passage of time and are consumed despite attempts to maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals, hoses, switches, thermostats, plastisol parts, lters, bearings, brushes, solenoids, orings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s sole discretion. This warranty covers the cost of replacement only and does not cover

Page 10

GENERAL INFORMATION

shipping or labor costs.

PUMP, VACUUM MOTOR AND HEATER ONE-YEAR LIMITED WARRANTY: Mytee warrants that pumps, vacuum and oor machine motors, and heaters will be free from manufacturing defects, defects in workmanship, and defects in material for one (1) year from the date of original purchase. This warranty does not apply and is void if the pump, vacuum motor, or heater has worn brush motors, water damage, chemical build-up, chemical damage, or evidence of abuse, neglect or tampering. This warranty covers the cost of replacement or repair only and does not cover shipping or labor costs.

HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT NOTICE.

LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.

All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication, improper installation, abuse, lack of maintenance, negligence in use or care, abnormal use, alteration of design, modication, use of incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor or service center. Mytee may make changes in products it manufactures and markets at any time; these changes are made without obligation to change, retrot, or upgrade any product previously sold or manufactured.

form for evaluation at the customer’s expense. This shipping is non-refundable. All warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if warranty will be approved. Any credit for repair and/or parts will only be issued upon evaluation and approval from Mytee Products, Inc.

3. When Warranty is approved, the Distributor’s account will be credited for the replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s) to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be credited for any parts sent for this claim.

Mytee has no obligation to honor the limited warranties set forth herein unless the original purchaser, promptly upon discovering the warranty claim and prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service center to describe the claim and to receive and follow instructions for documenting and resolving the claim. In addition, the purchaser must provide the product to which the claim applies to Mytee or a Mytee authorized distributor or service center for a thorough inspection. In addition, the purchaser must provide/return the product intact, unmodied, with all of its original parts.

If any provision or portion of this limited warranty policy is found to be unenforceable, then the remaining provisions and portions shall remain valid and enforceable. If any provision or portion of this limited warranty policy is found to be limited by law, then that provision or portion shall be construed to make it effective within the bounds of law. For example, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have the minimum duration required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible without violating the law.

The validity, construction and performance of this warranty policy shall be governed by the laws of the State of California, without respect to conicts of laws principles. The exclusive jurisdiction of any legal action arising from or related to this warranty policy shall be in the State of California and no legal action shall be commenced elsewhere.

Return Material Authorization Procedure

It is the responsibility of any Authorized Service Center (ASC) or Distributor with written authorization to ensure the Customers equipment is repaired as soon as possible. Only Mytee Products Inc. or it’s authorized dealers with written authorization, service centers, and agents may make warranty repairs on these products. All others do so at their own risk and expense.

The Distributor must follow Mytee Products, Inc. standard RMA procedure:

1. When a repair falls within the Warranty time period for a piece of equipment, the Distributor will ll out a RMA/Warranty claim form. This form will act as a repair order to replace any defective parts.

2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim

Page 11

NOTES

Page 12

NOTES

Mytee Products Inc.

13655 Stowe Dr.

Poway, CA 9 20 64

www.my te e. co m

Printed in the U.S.A.