Instructions for
M-3, M-5, M-12 & M-16 M-Series
Please read before use.
Register your product
at www.mytee.com/help
™
M-3 p. 2
M-5 p. 8
M-12 p. 14
M-16 p. 21
General information p. 27
Model #
Serial #
Form # ADM-MSeries
1-12
13655 Stowe Dr., Poway, Ca. 92064
1
M-3 M-SERIES™
M-3 BACKM-3 FRONT
10
9
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Female quick disconnect (QD)
4. Front handles
5. Prime valve
1
2
3
4
6
7
6. Pressure regulator
7. Front cooling fan
8. 4” locking casters
9. Solution tank
10. Solution tank cover
11
12
13
20
19
14
15
5
16
11. Recovery tank lid
12. Push handle
13. Drain valve
14. Auto-ll
15. Auto pump-out
17
16. Rear cooling fan
17. Dual power cords
18. 12” rear wheels
19. Latches (x2)
20. Recovery tank
18
M-3 ITEMS INCLUDED
H110 Cuff-Lynx™ H141 Cuff-Lynx™
2” Hose Adapter 2” Hose Reducer to 1.5”
H375 Hose Hanger H226 Drain Elbow
(4) screws
M-3 DUAL CORDS
Top cord: Plug into power Vac 1, Pump & Heater 1.
Bottom cord: Plug into power Vac 2, Pump-out & Heater 2.
Top cord
Bottom cord
Plug each of the two power cords into two separate, 20A grounded
wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits.
2
M-3 M-SERIES™
M-3 VAC/SOL HOSE CONNECTIONS
Before turning on switches, connect hoses to the extractor and a
wand or tool. Attach a solution hose to the front QD, the other end
to the tool. Attach a vacuum hose to the tool, the other to the front
Cuff-Lynx™ vacuum hose port. Just twist into place.
M-3 SWITCHES & PRESSURE GAUGE
VAC 2
VAC 1
HEATER
PUMP
Switches and Pressure Gauge are located on the plate in front
of the machine. The Amber light left of the Pressure Gauge will
illuminate when cords are plugged into two separate circuits. To use
vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on
Pump switch. Heater switch has three positions: Off (middle); 1,000
watts using one heater (left); and 2,000 using two heaters (right).
Red lights on panel display indicate watts selected: one light =
1,000 watts; two lights = 2,000 watts; no lights = heater is off.
M-3 FILL SOLUTION TANK
If not using the Auto-ll feature, lift the solution tank lid and manually ll
the tank.
M-3 AUTO-FILL & PUMP-OUT
AUTO-FILL
PUMP-OUT
PUMP-OUT
If using Auto-ll and Pump-out, connect one end of a 1/2 inch
garden hose to the top hose inlet in back of the machine, the other
end to a faucet. Add water pressure by turning on faucet. Attach a
second 1/2 inch garden hose to the bottom hose inlet, and place the
other end in a location where dirty water can drain. Turn on Pumpout switch. When job is complete, turn off Pump-out switch.
3
M-3 M-SERIES™
M-3 AUTO-FILL & FLOAT
After attaching a garden hose to the Auto-ll inlet, water will ll the
tank to a predetermined level until stopped by the oat. As water is
used and the level drops, water will once again enter the tank, and
be stopped again by the oat when maximum level is reached.
With each new job, check to make sure oat stops water after the
rst ll.
M-3 PRIME VALVE & PRESSURE REGULATOR
PRIME VALVE
HIGHER PSI
PRESSURE
REGULATOR
LOWER PSI
Prime the pump by turning the valve to the Prime position for 30
seconds, then turn horizontally to the Run position. Turn the
Pressure Regulator to the left to decrease the water pressure.
Turn the pressure regulator to the right to increase the water
pressure. Monitor pressure while adjusting, using Pressure Gauge
on Switch Panel.
M-3 DRAIN VALVE & LATCHES
You can drain the recovery tank by using the Drain Valve. When
not using the Auto Pump-out, you can drain the recovery tank by
using the Drain Valve. When the tank is full, an internal ball oat
will automatically shut off the vacuum. Attach the 45˚ drain elbow
to the drain spout, and lift up the Drain Valve to empty the tank.
Latches are located in the back to open tank for internal repairs.
M-3 FILTER MAINTENANCE
PUMP-OUT
FILTER
CLEAN WATER
INTAKE FILTER
To clean the internal lters, lift solution lid and/or remove recovery tank
lid, reach in and twist off. Rinse with clean water and replace.
PRIME VALVE
FILTER
4
M-3 M-SERIES™ PARTS & PRICING
1
SCALE: 1:2
DWG. NO.
D
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
mytee
M. LaBarbera
5/25/11
2
2
3
4
MSRP
2 $16.49 ea
2 $0.99 ea
2 $17.99 ea
1 $27.99 ea
QTY.
5
1 $23.99 ea
DESCRIPTION
hose, 3/8" x 14-1/2" (OAL), f
Thermostat, 200°, Auto, 1/4"
Thermostat, 310°F ± 10°F, Manual, 1/4"
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt 1 $5.99 ea
hose, 3/8" x 6.5", (OAL), f x fsw, 5400 Gray
screw, #6x3/16,phil pan head, self-tapping
6
NO.
E573
E574
H274
72
B207
AH184
AH156
73
74
75
76
PART
ITEM
71
NO.
$7.99/ft
1 $30.49 ea
2 $7.99 ea
1
1 $4.99 ea
3 $3.19 ea
1 $29.99 ea
24 $1.99 ea
1 $13.49 ea
ball valve, 1/4''
sol hose, kuriyama, 3/8"
clamp, hose, 5/16-29/32
hose, 3/8" x 10", (OAL), f x f
bracket, heater mounting, dual
adapter, brass, 3/8" barb x 1/4" fsw
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
B136
H528
77
B235
78
H347
80
PH715-28
80
B107 nipple, brass, 1/4"m, hex
B656
AH103
81
82
83
84
$8.99/ft
$8.99/ft
3 $1.99 ea
1 $39.99 ea
2 $3.49 ea
1
2 $2.49 ea
1 $86.99 ea
1 $8.49 ea
1
pump, 500 psi, 115V 1 $588.99 ea
sol hose, 1/2", kuri 100 psi
plug, brass, 3/8" mpt, hex
sol hose, 1/4" x 24 1/2", (OAL)
adapter, brass, 1/2" barb x 3/8" fsw, ball end
B246
B160
C313
AH108S
85
86
87
88
sol hose, 1/2", kuri 100 psi
regulator, 450 psi, silver spring
adapter, brass, 1/2" barb x 1/4" mpt
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
B644
B652
C313C
PH615-21
PH615-24
89
90
91
92
93
$5.99/ft
2 $11.49 ea
2 $3.19 ea
1
2 $9.49 ea
1 $13.99 ea
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
solution hose, black, low pressure, 1/2"
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
E550
B172
B242
H220
PH615A-10
97
98
94
95
96
1 $5.99 ea
2 $1.99 ea
2 $13.99 ea
1 $0.99 ea
13 $0.99 ea
latch, front breeze
nut, lock, 1/2" steel
nut, kep, #10-32 zinc
plate, switch, spotter
plug, brass, 3/4", garden hose 1 13.99 ea
screw, #10-32 x 3/4" phil pan head, zinc
H486
100
H273
101
H256
102
H410
103
B221
104
H221
99
1 $1.99 ea
1 $5.99 ea
2 $2.99 ea
2 $0.99 ea
2 $41.99 ea
wheel, 12"
guard, cooling fan, wire
filter, 60 mesh, garden hose
cap, brass, 3/4", garden hose 1 $1.49 ea
swivel, brass, 3/4" fgh x 1/2" fpt 1 $5.49 ea
fitting, brass, 3/4" mgh x 1/2" fpt
B640
B642
B120
B196
H296
H219 cap, axle, 1/2"
H251
105
106
107
108
109
110
111
3 $0.99 ea
1 $9.99 ea
1 $8.99 ea
2 $0.99
2 $0.99 ea
base, m series 1 $196.99 ea
washer, axle, cut 1/2" id
bracket, front hinge, sp/fb
bolt, 1/4-20 x 1 3/4" hex head, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
P707
H254
H232 axle, 19.75" x .50"
H378
H378
H201
112
113
114
117
115
116
$8.99/ft
2 $19.49 ea
1 $14.49 ea
1 $0.99 ea
1 $187.49 ea
4 $0.99 ea
1
1 $9.49 ea
pump out, 115v
sol hose, 1/2" kuri 100psi
bolt, 1/4-20 x 1" hex head, s/s 8 $0.99
caster, 4", black hub & gray tread
elbow, brass, 90 deg, 1/2" barb x 3/8" fpt
adapter, brass, 1/2" barb x 1/2" mpt
screw, 10-32 x 3/4", phil flat full thread, black oxide
H668
118
H342
119
B236
120
B132
H186
C381
PH615-37
PH615-17 sol hose, 1/2", black, 200 psi 200 degree max
121
122
123
124
125
MSRP
2 $4.99 ea
1 $9.99 ea
1 $62.49 ea
QTY.
DESCRIPTION
controller, circuit light
gasket, strip, 3/4" x 36" x 1/8"
filter, bag, vac tank, draw string
NO.
E564
PART
G085
G010
ITEMS NOT SHOWN
1 $3.19 ea
1 $10.99 ea
spout, drain, 45 degree
hanger, wire formed, hose
H375
H226
3
4
5
6
MSRP
6 $0.99 ea
1 $36.99 ea
7
QTY.
DESCRIPTION
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
8
NO.
PART
H304
G090
1
2
NO.
ITEM
$7.99/ft
1 $11.99 ea
1 $11.49 ea
3
1 $18.49 ea
1 $6.99 ea
pipe, pvc, 2" 1
elbow, 2" float
float, 2", ball style
gasket, 7", vac lid
G091
3
adaptor, pvc 2, fmsl x fmt
screw, 8 x 1/2", hex head, zinc
P726
P682
P684
H297
H490
4
5
6
7
8
F
1 $15.99 ea
1 $243.99 ea
1 $20.99 ea
1 $3.99 ea
2 $6.99 ea
1 $10.99 ea
inlet, 2"
valve, drain, 1-1/2"
elbow, inlet assembly 2"
bracket, "L" (all extracters)
Cuff-Lynx, 2" m cuff x 2" mpt
P709 vac tank, m series
P685
H225
H135
A926
H390A
9
11
12
13
14
10
4 $0.99 ea
1 $3.99 ea
3 $5.49 ea
6 $0.99 ea
1 $3.49 ea
1 $9.99 ea
3 $3.49 ea
filter, strainer, 1/4"
nipple, brass, 1/4" x close
washer, 9/16"id x 1"od, flat, s/s
mesh filter, auto dump, 1/2" npt
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
45 deg, street elbow, brass, 1/4" male NPTF
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
B119
B130
B106
H770
15
B111
H212
H333
16
17
18
19
20
21
E
9 $0.99 ea
2 $1.99 ea
1 $8.99 ea
1 $47.99 ea
3 $2.49 ea
1 $9.99 ea
2 $5.99 ea
4 $13.99 ea
1 $14.99 ea
light, red, 250v
switch, rocker, 2 position
nipple, brass, 3/8" x close
hose, pulse, 3/8" x 34", (OAL)
washer, 11/16"id x 1-1/2"od x .075, s/s
bushing, brass, 1/2"mpt x 3/8" fpt, hex
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt 8 $4.49 ea
B210
B216
B103
H299
AH203
22
23
24
26
25
switch, rocker, 3 position
light, indicator, 125v (amber)
plate, switch, sp, 4 hole w/gauge
E511
E515
E516
H337
E512B
28
29
30
31
27
D
3 $0.99 ea
3 $0.99 ea
1 $38.99 ea
1 $4.99 ea
1 $37.99 ea
1 $4.99 ea
1 $17.99 ea
2 $0.99
qd, brass, 1/4" f
bolt, 1/4-20 x 1 1/4"
plate, mounting, QD
Washer, #8, flat regular
gauge, pressure, 2000 PSI
screw, #10-32 x 1/2" SHCS, alloy
H389
H616
32
33
screw, 10-32 x 1/2" phil pan head, s/s 19 $0.99 ea
sol hose, 57 x 1/4", (OAL), m x msw 3000psi
adapter, brass, 3/8" female npt x 1/4" male npt
B643
B102
H484
H230
H203
AH195
H308D
34
35
36
37
38
39
40
5
8 $0.99 ea
6 $1.99 ea
4 $0.99
2 $0.99 ea
1 $12.99 ea
1 $124.99 ea
1 $23.99 ea
nut, hex, 1/4-20 s/s
valve, float, autofill
washer, 1/4" lock, s/s
cover, sol tank (m-series)
H213
43
H215
44
G212
45
nipple, 12" x 1/4" npt, m x m
bushing, brass, 3/8"mpt x 1/4" 4 $3.19 ea
B115
B105
H541
46
47
48
washer, 1/4"id x 1"od, flat, s/s
washer, buna 1-1/8" od x 3/16" id
H211
G052
42
41
C
$8.99/ft
1 $210.99 ea
2 $6.99 ea
1 $6.49 ea
5 $8.99 ea
1 $12.49 ea
2 $4.99 ea
13 $0.99 ea
sol tank, m series
handle, breeze and dx
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
P708
H485
H768
49
50
51
1
10 $0.99 ea
filter, strainer, 1/2"
B119A
52
exhaust boot, plastisol
cuff hose, 2 X 2, wire reinforced
screw, #10 x 5/8" hex head zinc
vac hose, 2", black wire reinforced
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
B186
H343
H544
G059
PH628-25
53
54
55
56
57
B
Part prices are subject to change.Order parts at: http://www.mytee.com/products/product.php?id=M-3
6 $4.99 ea
2 $139.99 ea
3 $1.49 ea
2 $8.99 ea
1 $15.99 ea
1 $13.49 ea
2 $0.99 ea
17 $0.99
35 $0.99 ea
10 $0.99
clamp, hose, 2-1/4 dia
vac support, 3 stage, 4-1/16"
H501
H217
C302 vac motor, 3 stage, 120V, tangential
58
59
60
washer, 1/4" flat, s/s
gasket, vacuum motor
plate, manifold, parallel
bolt, 1/4x20x3/4" hex head
manifold, dual vac, parallel
nut, lock, 1/4-20, nylon insert, s/s
P750
H601
H216
H210
G004
61
H202
65
62
63
64
66
A
washer, zinc, 1.625 x .847 x .078
H191
67
1 $39.99 ea
2 $78.99 ea
2 $51.99 ea
7
heating rod, 1000W, 115V
hose, pulse, 3/8" x 34", (OAL)
heater, aluminum cast, single
8
E519
AH202
H903A
68
69
70
F
E
D
11
1
12
3
2
1
4
5
7
10
9
8
M-3 M-SERIES™ PARTS & PRICING
C
13
B
20
17
19
18
14
18
16
15
23
24
23
21
22
78
#
thru B235
to prive valve
A
PRODUCTS, INC.
858-679-1191
M Series
mytee
TITLE:
DATE
5/25/11
NAME
M. LaBarbera
CHECKED
DRAWN
REV
OD
SHEET 2 OF 2
M3
DO NOT SCALE
DRAWING
DWG. NO.
D
SCALE: 1:2
SIZE
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
1
6
2
40
42
41
41
3
44
42
43
45
4
46
47
25
20
23
48
23
25
35
26
27
28
29
36
34
33
thru AH108s
to pump "OUT"
32
31
30
37
20 38
39
52
17
18
51
49
41
42
to heaters "OUT"
24
23
23
23
18
25
to regulator
86
#
76
#
thru B207
23
53
)
48
(#
thru B105
120
#
thru B236
to pump out
88
#
thru B160
to pump in
2
3
4
50
53
#
to AH202
65
63
51
64
5
58
58
60
61
59
66
51
54
56
55
86
6722
57
6
to B642
106
68
#
guage
to pressure
35
#
through B643
25
75
36
To qd
#
76
thru AH195
83
87
thru B186
38
48
65
66
65
85
38
100
101
30
102
101
105
106
109
97
54
98
99
22
125
#
#
thru B210
108
thru B132
to pump out
113
5
108
#
to B196
67
125
111 110
112 112
24
#
thru B142
to vac tank
80
124
65
123
101
120
121
6
122
to AH202
103
104
107
25
74
25
53
7
48
#
thru B105
to sol tank
8
F
78
69
70
71
73
72
?
20
#
thru B111
to vac tank
E
77
118
65
25
#
thru B103
to sol tank
89
82
80
80
81
48
83
80
88
78
17
18
25
25
84
80
90
91
92
to pump "in"
18 83
53
53
94
114
5141
87
#
50
50
115
116
43
65
65
119 23
65
7
117
88
96
90
95
944880
C
B
A
8
to sol tank
through B186
D
93
53
#
6
M-3 M-SERIES™ WIRING DIAGRAM
M3
Amber
PUMP
OUT
TopCord
BottomCord
7
M3Wiring
M-5 M-SERIES™
M-5 BACKM-5 FRONT
10
9
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Female quick disconnect (QD)
4. Front handles
5. Prime valve
1
2
3
4
6
7
6. Pressure regulator
7. Front cooling fan
8. 4” locking casters
9. Solution tank
10. Solution tank cover
11
12
13
20
19
14
15
5
16
11. Recovery tank lid
12. Push handle
13. Drain valve
14. Auto-ll
15. Auto pump-out
17
16. Rear cooling fan
17. Dual power cords
18. 12” rear wheels
19. Latches (x2)
20. Recovery tank
18
M-5 ITEMS INCLUDED
H110 Cuff-Lynx™ H141 Cuff-Lynx™
2” Hose Adapter 2” Hose Reducer to 1.5”
H375 Hose Hanger H226 Drain Elbow
(4) screws
M-5 DUAL CORDS
Top cord: Plug into power Vac 1 & Pump.
Bottom cord: Plug into power Vac 2 & Pump-out.
Top cord
Bottom cord
Plug each of the two power cords into two separate, 20A grounded
wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits.
8
M-5 M-SERIES™
M-5 VAC/SOL HOSE CONNECTIONS
Before turning on switches, connect hoses to the extractor and a
wand or tool. Attach a solution hose to the front QD, the other end
to the tool. Attach a vacuum hose to the tool, the other to the front
Cuff-Lynx™ vacuum hose port. Just twist into place.
M-5 SWITCHES & PRESSURE GAUGE
VAC 2
VAC 1
PUMP
PUMP OUT
Switches and Pressure Gauge are located on the plate in front of
the machine. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. To use
vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on
Pump switch. The Pressure Gauge displays the water pressure as
PSI. To use Pump-out feature, turn on Pump-out switch.
M-5 FILL SOLUTION TANK
If not using the Auto-ll feature, lift the solution tank lid and manually ll
the tank.
M-5 AUTO-FILL & PUMP-OUT
AUTO-FILL
PUMP-OUT
If using Auto-ll and Pump-out, connect one end of a 1/2 inch
garden hose to the top hose inlet in back of the machine, the other
end to a faucet. Add water pressure by turning on faucet. Attach a
second 1/2 inch garden hose to the bottom hose inlet, and place
the other end in a location where dirty water can drain.
9
M-5 M-SERIES™
M-5 AUTO-FILL & FLOAT
After attaching a garden hose to the Auto-ll inlet, water will ll the
tank to a predetermined level until stopped by the oat. As water is
used and the level drops, water will once again enter the tank, and
be stopped again by the oat when maximum level is reached.
With each new job, check to make sure oat stops water after the
rst ll.
M-5 PRIME VALVE & PRESSURE REGULATOR
PRIME VALVE
HIGHER PSI
PRESSURE
REGULATOR
LOWER PSI
Prime the pump by turning the valve to the Prime position for 30
seconds, then turn horizontally to the Run position. Turn the
Pressure Regulator to the left to decrease the water pressure.
Turn the pressure regulator to the right to increase the water
pressure. Monitor pressure while adjusting, using Pressure Gauge
on Switch Panel.
M-5 DRAIN VALVE & LATCHES
You can drain the recovery tank by using the Drain Valve. When
not using the Auto Pump-out, you can drain the recovery tank by
using the Drain Valve. When the tank is full, an internal ball oat
will automatically shut off the vacuum. Attach the 45˚ drain elbow
to the drain spout, and lift up the Drain Valve to empty the tank.
Latches are located in the back to open tank for internal repairs.
M-5 FILTER MAINTENANCE
PUMP-OUT
FILTER
CLEAN WATER
INTAKE FILTER
To clean the internal lters, lift solution lid and/or remove recovery tank
lid, reach in and twist off. Rinse with clean water and replace.
PRIME VALVE
FILTER
10
2
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
M-5 M-SERIES™ PARTS & PRICING
2
3
4
1 $9.99 ea
MSRP
QTY.
1 $3.19 ea
1 $3.99 ea
1 $10.99 ea
1 $3.99 ea
1
1
1 $3.99 ea
MSRP
4 $0.99 ea
6 $1.99 ea
2 $0.99 ea
1 $210.99 ea
1 $4.99 ea
1 $17.99 ea
1 $3.99 ea
1 $6.49 ea
1 $8.99 ea
2 $8.99 ea
6 $4.99 ea
1 $14.99 ea
1 $12.99 ea
1 $23.99 ea
1 $124.99 ea
5
QTY.
2 $0.99 ea
2 $0.99 ea
2 $0.99 ea
1 $3.99 ea
$7.99/ft
2 $6.99 ea
2 $18.49 ea
2 $11.49 ea
6 $0.99 ea
6 $0.99 ea
1 $36.99 ea
1 $11.99 ea
1 $15.99 ea
1 $243.99 ea
1 $20.99 ea
1 $62.49 ea
1 $0.99 ea
2 $10.99 ea
2 $6.99 ea
4 $0.99 ea
1 $9.99 ea
1 $4.99 ea
1 $47.99 ea
1 $38.99 ea
4 $13.99 ea
3 $0.99 ea
3 $0.99 ea
1 $9.99 ea
1 $8.99 ea
2 $1.99 ea
2 $0.99 ea
MSRP
QTY.
1 $4.99 ea
3
4
5
DESCRIPTION
gasket, vacuum motor
vac support, 3 stage, 4-1/16"
6
H501
G004
PART NO.
71
72
NO.
ITEM
MSRP
7
4 $0.99 ea
27 $0.99 ea
QTY.
DESCRIPTION
washer, 1/4" flat, s/s
8
plate, dual manifold, 9" x 13"
H253
73
14 $0.99 ea
nut, kep, #10-32 zinc
nut, hex, 1/4-20 s/s
valve, float, autofill
cover, sol tank (m-series)
G212
74
washer, 1/4" lock, s/s
nipple, 12" x 1/4" npt, m x m
B115
75
washer, buna 1-1/8" od x 3/16" id
H213
H541
H215
G052
79
77
76
78
$8.99/ft
1 $187.49 ea
1
1 $14.49 ea
9 $0.99 ea
24 $1.99 ea
pump out, 115v
clamp, hose, 5/16-29/32
sol hose, 1/2", kuri 100 psi
washer, 11/16"id x 1-1/2"od x .075, s/s
elbow, brass, 90 deg, 1/2" barb x 3/8" fpt
screw, 10-32 x 3/4", phil flat full thread, black oxide
PART NO.
NO.
ITEM
H186
1
H210
2
H273
3
C381
4
H347
PH615-37
5
6
F
B236
7
H299
8
qd, brass, 1/4" f
sol tank, m series
filter, strainer, 1/4"
filter, strainer, 1/2"
plate, mounting, QD
bolt, 1/4-20 x 1-1/4" hex head, s/s
P708
H203
H484
80
81
82
bracket, front hinge, sp/fb
B102
B119
H378
B119A
83
84
85
86
$8.99/ft
1
1 $9.49 ea
2 $2.49 ea
2 $0.99 ea
2 $0.99 ea
2 $41.99 ea
3 $0.99 ea
1 $9.99 ea
wheel, 12"
sol hose, 1/2", kuri 100 psi
adapter, brass, 1/2" barb x 1/2" mpt
adapter, brass, 1/2" barb x 1/4" mpt
B132
B644
PH615-17
9
10
11
washer, axle, cut 1/2" id
washer, zinc, 1.625 x .847 x .078
H191
H219 cap, axle, 1/2"
H251
H254
H232 axle, 19.75" x .50"
12
13
14
15
16
pipe, pvc, 2" 2
elbow, 2" float
float, 2", ball style
adaptor, pvc 2, fmsl x fmt
Cuff-Lynx, 2" m cuff x 2" mpt
bolt, 1/4-20 x 1-3/4" hex head, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
P684
H204
H135
88
89
2 $19.49 ea
P682
90
91
17 $0.99 ea
H201
87
screw, #8 x 5/8 phil oval, s/s
screw, #8 x 1/2", hex head, zinc
P726
H490
H297
H304
92
93
94
95
8 $0.99 ea
2 $6.99 ea
13 $0.99 ea
2 $3.49 ea
base, m series 1 $196.99 ea
handle, breeze and dx
nut, lock, 1/4-20 nylon insert
washer, 1/4"id x 1"od, flat, s/s
bolt, 1/4-20 x 1" hex head, s/s 8 $0.99 ea
caster, 4", black hub & gray tread
P707
H668
H342
H216
17
18
19
20
E
bushing, brass, 3/8"mpt x 1/4" 5 $3.19 ea
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
H768
21
adapter, brass, 1/2" barb x 3/8" fsw, ball end
B105
B160
H211
H485
22
23
24
25
inlet, 2"
gasket, 7", vac lid
valve, drain, 1-1/2"
lid, vac tank, black, 7"
controller, circuit light
elbow, inlet assembly 2"
screw, #8-32 x 3/8" SHCS, alloy
bracket, "L" (all extracters)
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
G090
96
G091
97
A926
98
P709 vac tank, m series
99
H225
100
P685
H246
H770
H390A
101
102
103
104
105
E564
$8.99/ft
1
1 $4.99 ea
1 $86.99 ea
1 $13.49 ea
6 $0.99 ea
3 $3.19 ea
3 $5.49 ea
2 $7.99 ea
1 $30.49 ea
ball valve, 1/4''
regulator, 450 psi
sol hose, 1/2", kuri 100 psi
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
B136
PH615-21
26
27
washer, 9/16"id x 1"od, flat, s/s
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt 5 $4.49 ea
B103
B656
H212
C313C
28
29
30
31
D
hose, 3/8" x 10", (OAL), f x f
adapter, brass, 3/8" barb x 1/4" fsw
45 deg, street elbow, brass, 1/4" male NPTF
B107 nipple, brass, 1/4"m, hex
B130
B235
AH103
32
33
34
35
washer, #8 flat, s/s
switch, rocker, 2 position
gauge, pressure, 2000 PSI
hose, pulse, 3/8" x 34", (OAL)
mesh filter, auto dump, 1/2" npt
screw, #10-32 x 1/2" SHCS, alloy
plug, dome 3/8", black
nipple, brass, 3/8" x close
light, indicator, 125v (amber)
plate, switch, sp, 4 hole w/gauge
adapter, brass, 3/8" female npt x 1/4" male npt
H333
106
B643
107
AH203
108
H308D
109
H389
110
111
H612
112
E512B
113
H337
114
B216
115
H422
116
E515
$7.99/ft
1
3 $3.49 ea
1 $3.49 ea
3 $2.99 ea
4 $8.99 ea
1 $39.99
3 $2.49 ea
2 $13.99 ea
2 $1.99 ea
14 $0.99 ea
sol hose, kuriyama, 3/8"
guard, cooling fan, wire
nipple, brass, 1/4" x close
screw, 10 x 5/8" hex head, zinc
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
hose, pulse, 3/8" x 34", (OAL)
bushing, brass, 1/2"mpt x 3/8" fpt, hex
2 $3.19 ea
18 $0.99 ea
latch, front breeze
nut, lock, 1/2" steel
fitting, strain relief, cord
screw, 10-32 x 1/2 phil pan
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
B111
B106
B186
PH715-28
36
37
H343
38
39
H296
40
B210
H230
H486
H221
AH202
43
41
42
C
H220
44
45
46
47
DESCRIPTION
PART NO.
ACCESSORIES
manual, m-series
ADM-M-SERIES
DESCRIPTION
gasket, strip, 3/4" x 36" x 1/8"
filrer, bag, vac tank, drawstring
G010
G085
PART NO.
ITEMS NOT SHOWN
$8.99/ft
2 $11.49 ea
2 $4.99 ea
1 $1.99 ea
1 $5.99 ea
2 $9.49 ea
1
connector, cord lock
filter, 60 mesh, garden hose
cap, brass, 3/4", garden hose 1 $1.49 ea
plug, brass, 3/4", garden hose 1 13.99 ea
power cord, pigtail, 30", 12/3, black
E550
B221
B120
B640
G131
48
49
50
51
52
sol hose, 1/2", kuri 100 psi
swivel, brass, 3/4" fgh x 1/2" fpt 1 $5.49 ea
fitting, brass, 3/4" mgh x 1/2" fpt
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
B642
B196
B172
PH615-10
53
54
55
56
B
Part prices are subject to change.Order parts at: http://www.mytee.com/products/product.php?id=M-5
spout, drain, 45 degree
hanger, wire formed, hose
stop sign, register your product
AD127
1 $8.49 ea
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
B652
57
cuff-lynx, 2" to 1.5" reducer
banana bag, mesh bag, yellow
screw. 10-32 x 1/2" phil pan head, s/s 2 $0.99 ea
cuff-lynx, 2" hose x 2" fem swivel cuff-lynx
H226
H230
H110
H375
H141
G029
$8.99/Ft
3 $1.99 ea
1 $13.99 ea
1
1 $37.99 ea
1 $26.49 ea
pump, 500 psi, 115V 1 $588.99 ea
sol hose, 1/2", kuri 100 psi
plug, brass, 3/8" mpt, hex
sol hose, 57 x 1/4", (OAL), m
sol hose, 1/4" x 24 1/2", (OAL)
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
B246
B242
C313
AH195
AH108S
PH615-15
58
59
60
61
62
63
$ 8.99/ft
2 $14.99 ea
4 $1.49 ea
1
10 $0.99 ea
clamp, hose, 2-1/4 dia
bolt, 1/4-20 x 3/4" hex head, s/s
manifold, single vac, no gasket
vac hose, 2", black wire reinforced
P735
H202
H217
PH628-25
64
65
66
67
A
6
2 $4.99 ea
2 $148.99 ea
7
2 $12.49 ea
exhaust boot, plastisol
cuff hose, 2 X 2, wire reinforced
motor, 3-stage, 115 cfm,14.5 amps
8
H544
G059
C302A
68
69
70
11
M-5 PARTS & PRICING
F
1
96
95
2
93
3
E
97
98
D
99
C
100
101
102
104
106
103
94
91
89
90
92
29
114
113
112
107
3 3
108
109
110
111
44
82
105
33
84
43
63
#
thru Ah108S
to 500 PSI pump
to 500 PSI
thru Ah195
pump "OUT"
37
83
thru B106
to prime valve
31
8
8
61
#
B
38
#
115
thru B236
to pump out "IN"
A
REV
OD
SHEET 2 OF 2
PRODUCTS, INC.
858-679-1191
TITLE:
5/24/11
M. LaBarbera
CHECKED
DRAWN
M5
M Series
DWG. NO.
D
SIZE
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
DO NOT SCALE
DRAWING
SCALE: 1:5
1
2
3
mytee
DATE
NAME
7
#
81
8
115
80
79
22
22
4
76
79
78
77
85
33
782
29
37
69
73
66
65
70
21
72
70
39
5
71
66
67
69
68
107
#
thru B643
6
to pressure gauge
63
61
37
#
thru B111
to female QD
25
7
8
F
thru B186
to sol tank
41
#
60
E
64
65
20
32
24
64220
62
24
58
24
59
55
6
to B644 #
2
41
11
D
thru B105
to auto fill
21
55
41
75
24
#
11
to B105
thru B652
to regulator
24
#
57
#
8
49
48
56
B642
to male
garden hose,
to auto fill thru
46
74
to sol tank
45
53
#
B115
thru B210
12
75
#
21
22
23
79
43
#
51
50
44
3
52
53
10
#
thru B132
to pump out "OUT"
54
47
20
2
88
13
14
15
16
40
43
40
39
42
24
38
thru B130
to vac tank
41
8
C
34
37
31
33
#
36
8
8
43
31
31
86
87
10 12
8
39
thru B216
to vac tank
17
2
20
21
22
to sol tank
23
24
26
25
35
33
34
32
B
8
29
115
#
19
thru B103
25
#
to 500psi
thru B160
pump "IN"
41
to regulator
thru B196
to female
garden hose
thru B105
54
#
24
#
4
6
6
9
7
6
6
2
3
6
4
6
5
1
6
5
18
7
29
#
6
11
27
57
32
31
29
30
41
thru B186
to pump "OUT"
28
31
29
A
8
12
D
C
B
A
E
F
SHEET 1 OF 1
REV
PRODUCTS, INC.
M-5 WIRING DIAGRAM
1
858-679-1191
TITLE:
CHECKED
DRAWN
M5
DO NOT SCALE
M Series
DWG. NO.
D
SIZE
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
DRAWING
1
SCALE: 1:2
mytee
DATE
NAME
9/10/2010
J.Cash
2
3
4
Green
5
Black
Out
Pump
White
Yellow
Blue
Red
Black
Brown
Black
Red
Black
Yellow
Vacuum
White
Green
2
3
4
5
Amber
Light
White
6
Vacuum
Brown
7
Red
Red
Black
Black
Blue
Pump
500psi
White
6
7
White
Green
Bottom Cord
8
115V
Top Cord
White
115V
Green
8
F
E
D
C
B
A
13
M-12
M-12 BACKM-12 FRONT
10
9
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Female quick disconnect (QD)
4. Front handles
5. Prime valve
1
2
3
4
6
7
6. Pressure regulator
7. Front cooling fan
8. 4” locking casters
9. Solution tank
10. Solution tank cover
11
12
13
20
19
14
15
5
16
11. Recovery tank lid
12. Push handle
13. Drain valve
14. Auto-ll
15. Auto pump-out
17
16. Rear cooling fan
17. Dual power cords
18. 12” rear wheels
19. Latches (x2)
20. Recovery tank
18
M-12 ITEMS INCLUDED
H110 Cuff-Lynx™ H141 Cuff-Lynx™
2” Hose Adapter 2” Hose Reducer to 1.5”
H375 Hose Hanger H226 Drain Elbow
(4) screws
M-12 DUAL CORDS
Top cord: Plug into power Vacuum 1, 2 & Pump-out.
Bottom cord: Plug into power Pump-Mode: Carpet & Tile.
Top cord
Bottom cord
Plug each of the two power cords into two separate, 20A grounded
wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits.
14
M-12
M-12 VAC/SOL HOSE CONNECTIONS
Before turning on switches, connect hoses to the extractor and a
wand or tool. Attach a solution hose to the front QD, the other end
to the tool. Attach a vacuum hose to the tool, the other to the front
Cuff-Lynx™ vacuum hose port. Just twist into place.
M-12 SWITCHES & PRESSURE GAUGE
VAC 2
VAC 1
PUMP MODE
PUMP OUT
Switches and Pressure Gauge are located on the plate in front
of the machine. The Amber light left of the Pressure Gauge will
illuminate when cords are plugged into two separate circuits. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump-out,
turn on Pump-out switch.
to Carpet. To use for Tile, turn the Pump Mode switch to Tile.
sure Gauge displays the water pressure as PSI.
CARPET TILE
To use on carpet, turn the Pump Mode switch
The Pres-
M-12 CARPET MODE
ON
PUMP MODE
CARPET
Press left side of Pump mode button for Carpet. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two
separate circuits. Two red lights left of switches will appear when Carpet mode is activated. In carpet cleaning mode, a 220 PSI pump and
solution heater are used. The 220 PSI is not adjustable. Adjusting the regulator in this mode will not affect the pump pressure.
15
M-12 TILE MODE
ON
PUMP MODE
M-12
TILE
Press right side of Pump mode button for Tile. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two
separate circuits. In Tile cleaning mode, a 1200 PSI pump will be used. Pump pressure is set using the regulator on the front of the unit.
There is no heat in tile mode. It is not possible to run the heater and 1200 PSI pump simultaneously.
M-12 FILL SOLUTION TANK
M-12 AUTO-FILL & PUMP-OUT
AUTO-FILL
PUMP-OUT
If not using the Auto-ll feature, lift the solution tank lid and manually ll
the tank.
If using Auto-ll and Pump-out, connect one end of a 1/2 inch
garden hose to the top hose inlet in back of the machine, the other
end to a faucet. Add water pressure by turning on faucet. Attach a
second 1/2 inch garden hose to the bottom hose inlet, and place
the other end in a location where dirty water can drain.
16
M-12
M-12 AUTO-FILL & FLOAT
After attaching a garden hose to the Auto-ll inlet, water will ll the
tank to a predetermined level until stopped by the oat. As water is
used and the level drops, water will once again enter the tank, and
be stopped again by the oat when maximum level is reached.
With each new job, check to make sure oat stops water after the
rst ll.
M-12 PRIME VALVE & PRESSURE REGULATOR
PRIME VALVE
HIGHER PSI
PRESSURE
REGULATOR
LOWER PSI
Prime the pump by turning the valve to the Prime position for 30
seconds, then turn horizontally to the Run position. Turn the
Pressure Regulator to the left to decrease the water pressure.
Turn the pressure regulator to the right to increase the water
pressure. Monitor pressure while adjusting, using Pressure Gauge
on Switch Panel.
M-12 DRAIN VALVE & LATCHES
You can drain the recovery tank by using the Drain Valve. When
not using the Auto Pump-out, you can drain the recovery tank by
using the Drain Valve. When the tank is full, an internal ball oat
will automatically shut off the vacuum. Attach the 45˚ drain elbow
to the drain spout, and lift up the Drain Valve to empty the tank.
Latches are located in the back to open tank for internal repairs.
M-12 FILTER MAINTENANCE
PUMP-OUT
FILTER
CLEAN WATER
INTAKE FILTER
To clean the internal lters, lift solution lid and/or remove recovery tank
lid, reach in and twist off. Rinse with clean water and replace.
PRIME VALVE
FILTER
17
M-12 PARTS & PRICING
2
3
3
2
4
MSRP
$4.49 ea
1
new/QTY.
5
DESCRIPTION
coupling, brass, 1/4" fpt x 1/4" fpt
6
B142A
PART NO.
81
NO.
ITEM
$6.49 ft
$6.49 ft
$0.99 ea
$4.99 ea
$86.99 ea
1
1
1
plate, mounting, QD
sol hose, 1/4", 300 PSI
regulator, 1000 psi, white spring
H484
C359C
PH634-36
82
83
84
$6.49 ea
$1.99 ea
$13.49 ea
1
1
1
2
1
ball valve, 1/4''
filter, strainer, 1/2"
sol hose, 1/4", 300 PSI
adapter, brass, 1/4" barb x 1/4" mpt
B656
B109
G034 grommet, rubber, 3/4" ID x 1-5/8" OD
B119A
PH634-20
87
88
89
85
86
$2.49 ea
$1.99 ea
$8.99 ea
$0.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$12.99 ea
$23.99 ea
2
2
1
2
2
6
1
1
1 $124.99 ea
2
1 $210.99 ea
sol tank, m series
valve, float, autofill
nipple, brass, 3/8" x close
bushing, brass, 1/2"mpt x 3/8" fpt, hex
B210
B216
90
91
cover, sol tank (m-series)
bracket, front hinge, sp/fb
H378
92
nipple, 12" x 1/4" npt, m x m
bolt, 1/4-20 x 1-1/4" hex head
washer, buna 1-1/8" od x 3/16" id
bolt, 1/4-20 x 1-1/2" hex head, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
B115
G212
96
97
H541-A
98
H203
99
P708
100
H201
93
H316
94
G052
95
$7.99/ft
$0.99 ea
$5.99 ea
$38.99 ea
$14.99 ea
1
1
$13.99 ea
3
2
$0.99 ea
3
$22.99 ea
1
light, red, 250v
switch, rocker, 3 position
switch, rocker, 2 position
gauge, pressure, 2000 PSI
screw, #10-32 x 1/2" SHCS, alloy
hose, pulse, black, 76" (OAL), 1/4" fsw x 3/8" msw
E516
E515
E511
H308D
102
H389
103
104
105
106
AH101
101
$6.49 ea
$0.99 ea
$9.99 ea
$6.99 ea
$3.99 ea
$8.99 ea
1
3
1
1
washer, #8 flat, s/s
Cuff-Lynx, 2" m cuff x 2" mpt
light, indicator, 125v (amber)
plate, switch, sp, 4 hole w/gauge
$11.49 ea
3
1
2
1
pipe, pvc, 2" 1
elbow, 2" float
adaptor, pvc 2, fmsl x fmt
screw, #8 x 1/2", hex head, zinc
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
P682
P726
P684
H297
H135
H612
H337
G002
E512B
114
113
115
111
112
110
107
108
109
$0.99 ea
$18.49 ea
$36.99 ea
$11.99 ea
$15.99 ea
1
1
6
1
1
1 $243.99 ea
float, 2", ball style
gasket, 7", vac lid
lid, vac tank, black, 7"
elbow, inlet assembly 2"
screw, #8 x 5/8 phil oval, s/s
G090
117
H304
118
G091
119
P709 vac tank, m series
A926
120
121
H490
116
$6.99 ea
$0.99 ea
$9.99 ea
$20.99 ea
$10.99 ea
1
2
4
1
1
inlet, 2"
valve, drain, 1-1/2"
bracket, "L" (all extracters)
mesh filter, auto dump, 1/2" npt
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
P685
H225
H770
H333
H390A
122
123
124
125
126
MSRP
$9.99 ea
$3.49 ea
$62.49 ea
$74.99 ea
1
1
1
2
QTY.
DESCRIPTION
controller, circuit light
strap, velcro, w/buckle
filter, bag, vac tank, drawstring
power cord, ext, 50', 12/3, black
E564
E530
G010
PART NO.
G147
ITEMS NOT SHOWN
MSRP
$6.49 ft
1
QTY
DESCRIPTION
sol hose, 1/4", kuri
PART NO.
PH634-36
ACCESSORIES
$0.99 ea
$3.99 ea
$3.99 ea
$3.19 ea
$3.99 ea
$10.99 ea
1
1
1
1
1
1
1
1
DATE
NAME
manual, m-series
ADM-M-SERIES
spout, drain, 45 degree
Cuff-Lynx instruction guide
stop sign, register your product
AD127
hanger, wire formed, hose
Cuff-Lynx, 2" ro 1.5" reducer
screw, 10-32 x 1/2" phil pan head s/s 2
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
UNLESS OTHERWISE SPECIFIED:
H375
H226
H230
H110
H141
G029 banana bag, mash bag, yellow
ADM-Cuff-Lynx
PRODUCTS, INC.
858-679-1191
M Series
mytee
TITLE:
7/10/11
M. LaBarbera
COMMENTS:
CHECKED
DRAWN
.003
.001
.005
.5
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR:
ONE PLACE DECIMAL
TWO PLACE DECIMAL
THREE PLACE DECIMAL
REV
OD
SHEET 1 OF 2
DO NOT SCALE
DRAWING
M12
DWG. NO.
D
SCALE: 1:8
SIZE
FINISH
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
4
5
6
MSRP
$4.99 ea
$3.19 ea
$0.99 ea
$13.99 ea
$27.99 ea
1
1
2
4
7
new/QTY.
1 $208.99 ea
DESCRIPTION
valve, brass, 1/4" check
8
B108
PART NO.
1
NO.
ITEM
pump, 200psi, bypass, 115V
bushing, brass, 3/8"mpt x 1/4" 5
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
screw, 10-32 x 1-1/4", phil flat full thread, black oxide
B136
B105
H185
AH184 hose, 3/8" x 14-1/2" (OAL), f
C322D
2
3
4
5
6
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$9.99 ea
$4.49 ea
7
2
24
20
washer, 1/4" flat, s/s
nut, kep, #10-32 zinc
$0.99 ea
$41.99 ea
2
4
1
16
wheel, 12"
base, m series 1 $196.99 ea
nut, hex, 1/4-20 s/s
washer, axle, cut 1/2" id
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
B103
H210
H273
7
8
9
F
H219 cap, axle, 1/2"
H251
H254
H232 axle, 19.75" x .50"
10
11
12
13
P707
14
H215
15
$0.99 ea
$0.99 ea
$3.19 ea
$0.99 ea
$0.99 ea
$6.99 ea
$19.49 ea
2
3
2
12
washer, 1/4" lock, s/s
bolt, 1/4-20 x 1" hex head, s/s 8
caster, 4", black hub & gray tread
$0.99 ea
$17.99 ea
2
8
2
4
10 $0.99
qd, brass, 1/4" f
handle, breeze and dx
screw, 10-32 x 5/8" hex head, zinc
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
B107 nipple, brass, 1/4"m, hex
H668
16
B102
H342
H213
H212 washer, 9/16"id x 1"od, flat, s/s
H768
17
18
19
20
21
22
E
H211 washer, 1/4"id x 1"od, flat, s/s
H485
H206
24
23
25
$2.99 ea
3
guard, cooling fan, wire
H296
26
$8.99 ft
$0.99 ea
$9.49 ea
$1.99 ea
$21.49 ea
1
$14.49 ea
2
8
2
2
1
fan, cooling, 115V
screw, 10 x 5/8" hex head, zinc
washer, zinc, 1.625 x .847 x .078
adapter, brass, 1/2" barb x 1/2" mpt
elbow, brass, 90 deg, 1/2" barb x 3/8" fpt
sol hose, 1/2" black, 200 psi 200 degree max
B236
B132
H343
H191
C317
PH615-36
27
32
28
29
30
31
$0.99 ea
$1.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$29.99 ea
$78.99 ea
$16.49 ea
9
6
1
2
2
16
clamp, hose, 5/16-29/32
Thermostat, 200°, Auto, 1/4"
heater, aluminum cast, single
bracket, heater mounting, dual
washer, 11/16"id x 1-1/2"od x .075, s/s
screw, #10-32 x 3/4" phil pan head, zinc
H299
33
E573
H347
H256
H528
H903A
34
35
36
37
38
D
$5.99 ea
$17.99 ea
$51.99 ea
8
2
2
10
heating rod, 1000W, 115V
6-32 x 3/16 p-pan internal sem zinc
phil pan head screw zinc, 6-32 x 3/16"
Thermostat, 310°F ± 10°F, Manual, 1/4"
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt 1
E574
E519
B207
H274
H275
39
40
41
42
43
$0.99 ea
$3.99 ea
$8.99 ea
$0.99 ea
$4.99 ea
$15.99 ea
$23.99 ea
6
2
1
1
hose, 3/8" x 6.5" (OAL), f x fs, 5400 gray
AH156
44
9
2
exhaust boot, plastisol
G059
45
10
gasket, vacuum motor
vac support, 2 stage, 3-1/8"
nut, lock, 1/4-20 nylon insert
manifold, dual vac, parallel
bolt, 1/4-20 x 3/4" hex head, s/s
P750
H202
H500
H216
G004
50
46
47
48
49
C
$8.99/ft
$0.99 ea
$1.49 ea
$13.49 ea
$12.49 ea
3
1
1
1
3
clamp, hose, 2-1/4 dia
plate, manifold, parallel
screw, 1/4-20 x 1", phil flat
cuff hose, 2 X 2, wire reinforced
vac hose, 2", black, wire reinforced
H188
H601
H217
H544
PH628-21
51
52
53
54
55
$5.99 ea
13.99 ea
$1.99 ea
$5.49 ea
$1.49 ea
$0.99 ea
$1.99 ea
$3.19 ea
$13.99 ea
$11.49 ea
2 $103.99 ea
vac motor, 2 stage high performance
C310
56
1
1
2
18
latch, front breeze
screw, 10-32 x 1/2 phil pan
filter, 60 mesh, garden hose
cap, brass, 3/4", garden hose 1
plug, brass, 3/4", garden hose 1
swivel, brass, 3/4" fgh x 1/2" fpt 1
fitting, brass, 3/4" mgh x 1/2" fpt
B221
B640
B642
B120
B196
H230
H486
57
62
58
59
60
61
63
B
2
2
2
nut, lock, 1/2" steel
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
E550
H221
H220
64
65
66
$4.99 ea
$6.99 ea
$4.99 ea
$39.99 ea
2
1 $187.49 ea
1
1
1
pump out, 115v
tee, brass, 1/4" fpt
connector, cord lock
hose, pulse, 3/8" x 34", (OAL)
adapter, brass, 3/8" female npt x 1/4" male npt
B113
B643
C381
G131
AH202
68
69
70
71
67
$8.99 ft
$5.49 ea
2
tee, brass, 1/4" mpt
B135
72
$2.49 ea
$8.99 ea
$8.49 ea
1
4
1
1
pump, 1200 psi 1 $708.99 ea
adapter, brass, 1/2" barb x 1/4" mpt
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
sol hose, 1/2", black, 200 psi 200 degree max
B644
B186
B652
C359A
PH615-9
77
73
74
75
76
A
$3.49 ea
$3.49 ea
1
1
2
7
nipple, brass, 1/4" x close
hose, pulse, black, 49" (OAL), 1/4" fswl x 1/4" fswl
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
B111
AH117
78
79
8
B106
80
Part prices are subject to change.Order parts at: http://www.mytee.com/products/product.php?id=M-12
18
M-12 PARTS & PRICING
F
1
2
3
4
101
guage
#
thru AH101
to pressure
5
73
75
74
74
74
4
19
to QD
(upper)
thru AH117
6
7
8
F
50
78
#
76
49
7
4
72
thru B130
to 220 psi
pump "IN"
54
53
116
115
77
69
9
#
D
M12 updating
E
D
C
122
118
119
121
120
117
REV
123
B
124
32
#
to pump-out
"IN' thru B236
91
90
33
125
126
A
PRODUCTS, INC.
858-679-1191
M Series
mytee
TITLE:
DATE
7/10/11
NAME
M. LaBarbera
COMMENTS:
CHECKED
DRAWN
.003
.001
.005
.5
UNLESS OTHERWISE SPECIFIED:
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR:
ONE PLACE DECIMAL
TWO PLACE DECIMAL
THREE PLACE DECIMAL
REV
OD
DWG. NO.
SIZE
FINISH
SHEET 2 OF 2
DO NOT SCALE
DRAWING
M12
D
SCALE: 1:7
1
8
109
111
111
112
113
114
108
110
107
106
105
100
4
99
#
thru B105
to auto fill
107106
104
103
9
101
102
9
79
80
62
81
19
82
85
86
87
89
83
to 1200 psi
pump "OUT"
84
85
88
7221
33
thru B186
to 12oo psi
pump "OUT"
19
#
thru B107
91
33
74
#
78
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
4
2
3
74
95 95 23
98
23
18
15
9
97
79
70
61
garden
#
to female
71
hose thru B196
91
#
thru B216
to vac tank
67
30
29
32
33
68
32
thru B108
to 220 psi
pump "OUT"
55
56
43
22
44
32
1
#
33
thru B132
to auto fill
66
65
35
2
31
#
64
to QD
8
(lower)
96
57
63
62
21
#
thru B107
22
94
23
95
24
29
"OUT" thru
H191 #
to pump-out
58
59
60
61
8
10
12
72
13
#
thru B135
to sol tank
14
15
19
29
28
9
27
26
30
25
37
36
4
thru B115
to auto fill
8
35
59
hose
#
garden
31
to male
thru B642
34
32
33
97
#
C
45
42
46
52
51
50
E
41
47
40
15
48
49
38
39
39
D
90
92
93
18
7
49
7
11
5
6
7
8
2
16
17
7
18
20
22
21
2
AH184
#
to heater
"OUT" thru
23
9
4
71
#
pumps "IN"
thru AH202
to 220/1200 psi
3
2
1
43
B207
#
"IN" thru
to heater
5
6
7
24
8
B
A
19
M-12 WIRING DIAGRAM
A
A
B
B
C
C
D
D
E
E
1 1
2 2
3 3
4 4
Pump
1200
Pump
Out
Pump
200
White
Black
Black
White
Green
Red
Green
Green
White
White
Blue
Green
White
Blue
Brown
Red
Black
Black
Yellow
115v
115v
MyteeProducts,Inc.
M12WiringDiagram
1000W
H1
1000W
H2
Motor
2
Motor
1
SW2
SW3
SW4
SW1
Top
Cord
Bottom
Cord
20
M-16
M-16 BACKM-16 FRONT
10
9
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Female quick disconnect (QD)
4. Front handles
5. Prime valve
1
2
3
4
6
7
6. Pressure regulator
7. Front cooling fan
8. 4” locking casters
9. Solution tank
10. Solution tank cover
11
12
13
20
19
14
15
5
16
11. Recovery tank lid
12. Push handle
13. Drain valve
14. Auto-ll
15. Auto pump-out
17
16. Rear cooling fan
17. Dual power cords
18. 12” rear wheels
19. Latches (x2)
20. Recovery tank
18
M-16 ITEMS INCLUDED
H110 Cuff-Lynx™ H141 Cuff-Lynx™
2” Hose Adapter 2” Hose Reducer to 1.5”
H375 Hose Hanger H226 Drain Elbow
(4) screws
M-16 DUAL CORDS
Top cord: Plug into power Vacuum 1 & 2.
Bottom cord: Plug into power Pump & Pump-out.
Top cord
Bottom cord
Plug each of the two power cords into two separate, 20A grounded
wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits.
21
M-16
M-16 VAC/SOL HOSE CONNECTIONS
Before turning on switches, connect hoses to the extractor and a
wand or tool. Attach a solution hose to the front QD, the other end
to the tool. Attach a vacuum hose to the tool, the other to the front
Cuff-Lynx™ vacuum hose port. Just twist into place.
M-16 SWITCHES & PRESSURE GAUGE
VAC 2
VAC 1
PUMP
PUMP OUT
Switches and Pressure Gauge are located on the plate in front of
the machine. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. To use
vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on
Pump switch. The Pressure Gauge displays the water pressure as
PSI. To use Pump-out feature, turn on Pump-out Switch.
M-16 FILL SOLUTION TANK
If not using the Auto-ll feature, lift the solution tank lid and manually ll
the tank.
M-16 AUTO-FILL & PUMP-OUT
AUTO-FILL
PUMP-OUT
If using Auto-ll and Pump-out, connect one end of a 1/2 inch
garden hose to the top hose inlet in back of the machine, the other
end to a faucet. Add water pressure by turning on faucet. Attach a
second 1/2 inch garden hose to the bottom hose inlet, and place
the other end in a location where dirty water can drain.
22
M-16
M-16 AUTO-FILL & FLOAT
After attaching a garden hose to the Auto-ll inlet, water will ll the
tank to a predetermined level until stopped by the oat. As water is
used and the level drops, water will once again enter the tank, and
be stopped again by the oat when maximum level is reached.
With each new job, check to make sure oat stops water after the
rst ll.
M-16 PRIME VALVE & PRESSURE REGULATOR
PRIME VALVE
HIGHER PSI
PRESSURE
REGULATOR
LOWER PSI
Prime the pump by turning the valve to the Prime position for 30
seconds, then turn horizontally to the Run position. Turn the
Pressure Regulator to the left to decrease the water pressure.
Turn the pressure regulator to the right to increase the water
pressure. Monitor pressure while adjusting, using Pressure Gauge
on Switch Panel.
M-16 DRAIN VALVE & LATCHES
You can drain the recovery tank by using the Drain Valve. When
not using the Auto Pump-out, you can drain the recovery tank by
using the Drain Valve. When the tank is full, an internal ball oat
will automatically shut off the vacuum. Attach the 45˚ drain elbow
to the drain spout, and lift up the Drain Valve to empty the tank.
Latches are located in the back to open tank for internal repairs.
M-16 FILTER MAINTENANCE
PUMP-OUT
FILTER
CLEAN WATER
INTAKE FILTER
To clean the internal lters, lift solution lid and/or remove recovery tank
lid, reach in and twist off. Rinse with clean water and replace.
PRIME VALVE
FILTER
23
M-16 PARTS & PRICING
2
2
3
4
MSRP
1 $12.99 ea
6 $1.99 ea
1 $8.99 ea
4 $0.99 ea
2 $0.99 ea
2 $0.99 ea
2 $1.99 ea
2 $5.49 ea
1 $6.49 ea
1 $17.99 ea
1 $4.99 ea
1 $37.99 ea
2 $0.99 ea
2 $0.99 ea
3 $0.99 ea
3 $0.99 ea
4 $13.99 ea
1 $9.99 ea
1 $38.99 ea
1 $243.99 ea
2 $6.99 ea
1 $8.99 ea
4 $0.99 ea
1 $9.99 ea
1 $14.49 ea
1 $3.99 ea
1 $3.49 ea
1 $3.99 ea
1 $6.49 ea
1 $23.99 ea
1 $210.99 ea
11 $0.99 ea
QTY.
5
1 $15.99 ea
1 $20.99 ea
1 $10.99 ea
$7.99/ft
1 $6.99 ea
1 $11.49 ea
1 $18.49 ea
1 $11.99 ea
1 $36.99 ea
6 $0.99 ea
MSRP
QTY
2 $4.99 ea
1 $62.49 ea
1 $9.99 ea
1 $10.99 ea
3
4
5
DESCRIPTION
sol tank, m series
cover, sol tank (m-series)
nipple, 12" x 1/4" npt, m x m
washer, 11/16"id x 1-1/2"od x .075, s/s
6
B115
P708
H299
PART NO.
NO.
ITEM
G212
71
72
73
74
MSRP
1 $21.49 ea
3 $2.99 ea
7
QTY.
DESCRIPTION
2 $6.99 ea
15 $0.99 ea
fan, cooling, 115V
handle, breeze and dx
guard, cooling fan, wire
screw, #10 x 5/8" hex head zinc
8
qd, brass, 1/4" f
filter, strainer, 1/2"
sol, hose, 57 x 1/4"
washer, 1/4" lock, s/s
bracket, front hinge, sp/fb
washer, buna 1-1/8" od x 3/16" id
nipple, brass, 3/8" x close
bolt, 1/4-20 x 1-3/4" hex head, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
plate, mounting, QD
45 deg, street elbow, brass, 1/4" male NPTF
B216
B130
H378
H213
H201
76
77
10 $0.99 ea
H204
78
79
1 $13.49 ea
14 $0.99 ea
G052
75
8 $0.99 ea
ball valve, 1/4''
washer, 1/4"id x 1"od, flat, s/s
nut, lock, 1/4-20 nylon insert
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt 7 $4.49 ea
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
B102
H484
B119A
AH195
80
81
82
83
84
85
3 $0.99 ea
2 $19.49 ea
24 $0.99 ea
base, m series 1 $196.99 ea
washer, 1/4" flat, s/s
nut, lock, 10-32, thin pattern
bolt, 1/4-20 x 1" hex head, s/s 8 $0.99 ea
caster, 4", black hub & gray tread
washer, #8 flat, s/s
nut, hex, 1/4-20 s/s
H215
86
1 $9.99 ea
4 $0.99 ea
switch, rocker, 2 position
light, indicator, 125v (amber)
screw, #10-32 x 1/2" SHCS, alloy
bolt, 1/4-20 x 1-1/4" hex head, s/s
E515
H203
H389
H612
E512B
87
88
89
90
91
2 $41.99 ea
2 $0.99 ea
1 $5.99 ea
wheel, 12"
washer, axle, cut 1/2" id
cap, brass, 3/4", garden hose 1 $1.49 ea
swivel, brass, 3/4" fgh x 1/2" fpt 1 $5.49 ea
fitting, brass, 3/4" mgh x 1/2" fpt
gauge, pressure, 2000 PSI
filter, strainer, 1/4"
bracket, "L" (all extracters)
plate, switch, sp, 4 hole w/gauge
H337
H308D
92
93
1 $1.99 ea
filter, 60 mesh, garden hose
plug, brass, 3/4", garden hose 1 13.99 ea
mesh filter, auto dump, 1/2" npt
elbow, brass, 90 deg, 1/2" barb x 3/8" fpt
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
B236
P709 vac tank, m series
H390A
94
95
2 $13.99 ea
14 $0.99 ea
latch, front breeze
nut, kep, #10-32 zinc
B119
H770
H333
96
97
98
99
2 $4.99 ea
2 $11.49 ea
2 $3.19 ea
18 $0.99 ea
connector, cord lock
fitting, strain relief, cord
screw, 10-32 x 1/2 phil pan
power cord, pigtail, 30", 12/3, black
inlet, 2"
pipe, pvc, 2" 1
elbow, 2" float
float, 2", ball style
nipple, brass, 1/4" x close
Cuff-Lynx, 2" m cuff x 2" mpt
adaptor, pvc 2, fmsl x fmt
valve, drain, 1-1/2"
elbow, inlet assembly 2"
gasket, 7", vac lid
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
B106
H135
100
101
2 $1.99 ea
2 $1.99 ea
nut, lock, 1/2" steel
washer, zinc, 1.625 x .847 x .078
P685
P684
P726
P682
H225
A926
G002
102
103
104
105
$8.99/ft
4 $0.99 ea
1 $9.49 ea
24 $1.99 ea
sol hose, kuriama, 1/2" 1
clamp, hose, 5/16-29/32
adapter, brass, 1/2" barb x 1/2" mpt
screw, #10-32 x 1-1/4" phil pan head, zinc
H490
G091
106
108
109
110
107
$8.99/ft
3 $2.49 ea
1 $187.49 ea
pump out, 115v
1 $39.99 ea
sol hose, kuriama, 1/2" 1
hose, pulse, 3/8" x 34" OAL
bushing, brass, 3/8"mpt x 1/4" 7 $3.19 ea
bushing, brass, 1/2"mpt x 3/8" fpt, hex
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
DESCRIPTION
gasket, strip, 3/4" x 36" x 1/8"
H304
G090
111
112
G085
PART NO
ITEMS NOT SHOWN
$8.99/ft
1 $13.49 ea
10 $0.99 ea
plate, manifold, parallel
bolt, 1/4-20 x 3/4" hex head, s/s
1 $12.49 ea
2 $8.99 ea
6 $3.99 ea
3 $0.99 ea
1 $15.99 ea
1
manifold, dual vac, parallel
vac hose, 2", black, wire reinforced
2 $103.99 ea
gasket, vacuum motor
vac support, 2 stage, 3-1/8"
cuff hose, 2 X 2, wire reinforced
vac motor, 2 stage high performance
2 $4.99 ea
3 $1.49 ea
exhaust boot, plastisol
clamp, hose, 2-1/4 dia
screw, 1/4-20 x 1, phil flat full thread, blacl oxide
controller, circuit light
hanger, wire formed, hose
filter, bag, vac tank, draw string
E564
H375
G010
$7.99/ft
6 $0.99 ea
3 $3.19 ea
2 $7.99 ea
2 $13.99 ea
1 $8.49 ea
6 $3.49 ea
1
sol hose, kuriyama, 3/8"
nipple, brass, 1/4"m, hex
washer, 9/16"id x 1"od, flat, s/s
adapter, brass, 3/8" barb x 1/4" fsw
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
$8.99/ft
2 $47.99 ea
2 $3.49 ea
1
sol hose, 3/8" x 10"
unloader, 1200 psi 1 $126.49 ea
sol hose, 1/2" kuri 100psi
adapter, brass, 1/2" barb x 3/8" fsw, ball end
$8.99/ft
3 $2.49 ea
2 $47.99 ea
1
5 $8.99 ea
1 $9.49 ea
pump, 1200 psi 1 $708.99 ea
sol hose, 1/2" kuri 100psi
hose, pulse, 3/8" x 34", OAL
adapter, brass, 1/2" barb x 1/4" mpt
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
6
$8.99/ft
1
1 $124.99 ea
7
valve, float, autofill
sol hose, 1/2" kuri 100psi
8
PART NO.
NO.
ITEM
C317
1
H296
2
H343
3
H485
4
H211
5
F
H768
6
B103
7
H210
11
H668
12
H342
13
P707
14
H232 axle, 19.75" x .50"
15
H216
H458
8
9
10
H254
16
H251
17
E
B196
B120
B642
H219 cap, axle, 1/2"
18
19
20
21
B640
22
B656
B221
23
H273
24
H486
25
H230
26
G131
27
E550
28
H220
29
D
H221
30
H191
31
B132
32
H347
33
H222
PH615-17
35
34
24
C381
36
B210
PH615-37
38
37
B105
39
AH202
40
H601
41
H202
42
C
H188
43
P750
44
H544
PH628-20
46
45
G004
47
H500
48
C310
49
H217
50
G059
51
Part prices are subject to change.Order parts at: http://www.mytee.com/products/product.php?id=M-16
H212
52
B107
53
B235
54
B
B242
PH715-27
55
56
B652
57
B111
58
AH104
59
H306B
60
B160
61
B644
PH615-22
63
62
C359A
64
AH203
65
B186
PH615-34
67
66
A
B172
68
H541
PH615-8
70
69
M-16 PARTS & PRICING
F
1
112
110
111
2
3
E
109
3
108
D
105
106
107
87
5
75
C
104
7
65
90
75
5
86
77
103
24
24
93
92
91
89
88
84
B
102
101
95
94
26
58
83
97
38
96
65
#
thru AH203
To pump "OUT"
85
82
3872728072
52
52
81
58
100
99
80
98
72
72
72
39
#
thru B105
To regulator
72
67
To pump "IN"
54
#
thru B235
To PH715-27
37
#
thru PH615-37
To pump out "IN"
61
#
thru B160
A
PRODUCTS, INC.
858-679-1191
mytee
TITLE:
DATE
5/25/11
NAME
M. LaBarbera
CHECKED
DRAWN
REV
OD
DO NOT SCALE
M16
M Series
DWG. NO.
D
SIZE
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
SHEET 2 OF 2
DRAWING
1
SCALE: 1:6
2
3
761177
111213
7
To PH715-27
6
5
4
72
53
#
thru B107
52
39
7
81
52
72
11
9
78
61
#
thru B160
To regulator
67
79
40
#
To AH202
4
5
6
7
70
7
4
6
5
75
4
18
17
16
15
14
9
8
1
2
3
27
To B196
28
19
#
37
29
thru B105
To sol tank
31
32
7139727273
67
#
30
33
35
36
25
thru B210
To AH202
34
11
74
32
#
thru B132
To pump
out "OUT"
26
24
20
19
22 23
21
38
#
53
#
24
thru B107
To regulator
66
54
To B642
31
63
39 63
39
58
53
21
#
thru B186
To sol tank
53
40
67
#
62
33
61
39
52
7
#
thru B103
To ball valve
thru B236
To vac tank
60
33
To q.d
98
#
58
63
7
85
#
thru AH195
68
67
67
65
#
guage
thru AH203
To pressure
5
6
7
65
64
11
39
42
9
7
#
thru B103
To ball valve
58
#
thru B111
To vac tank
54
6
49
48
47
10
45
44 46
43
42
41
69
67
56
33
61
58
58
59
58
57
53
52
39 56
7
55
50
51
38
8
F
E
thru B186
To auto fill
67
#
D
C
B
A
8
25
1
1
M-16 WIRING DIAGRAM
Black
2
Yellow
Out
Pump
White
3
Black
Brown
Black
Yellow
PRODUCTS, INC.
mytee
DATE
NAME
White
858-679-1191
9/10/2010
J.Cash
DRAWN
TITLE:
CHECKED
REV
SHEET 1 OF 1
DO NOT SCALE
DRAWING
M16
M Series
DWG. NO.
D
SCALE: 1:2
SIZE
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
2
3
Blue
4
Green
5
White
Red
Red
Black
Amber
Light
Red
Black
Brown
Green
4
5
6
Pump
1200psi
Blue
Red
7
Green
115V
Bottom Cord
White
White
115V
Top Cord
26
6
Vacuum Vacuum
White
Black
7
Green
38.27
General information
Dear Customer:
Congratulations on the purchase of your new M-Series™ Extractor. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior quality
and technology.
Keep in mind that the M-Series™ Extractor is a machine, so neglect or abuse will
cause unnecessary damage and void the warranty. However with simple maintenance the M-Series™ will give quality performance for many years to come.
If warranty questions arise, please consult user manual or get in touch with your
distributor. If you have questions about maintenance, replacing parts or ordering
parts, please call an authorized Mytee Products Inc. Service Center. To see an
updated list, visit our website at www.mytee.com
Before you begin using, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed in accordance
with all local code and ordinances. Do not remove ground pin; if missing, replace
plug before use.
Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualied electrician or service person if you are in
doubt as to whether the outlet is properly grounded. Do not modify the plug provided
with the machine. If it will not t the outlet, have a proper outlet installed by a
qualied electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualied electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounding Pin
Figure 1
Grounded Outlet
Metal
Screw
Grounded Outlet Box
Figure 2 Figure 3
Adapter
Tab for Grounding
Screw
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Name Plate
The Model and Serial Number of your machine are shown on the name plate located
on the inside of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to le a
freight damage claim.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause severe personal injury or death.
Is used to call attention to a situation that could cause severe personal injury.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of re, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where ammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
14. Keep hair, loose clothing, ngers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when using on stairs.
16. To reduce the risk of re or electric shock, do not use this machine with a solidstate speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid,
alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
Pre-Operation
1. Remove furniture and other items from the area you are going to clean.
2. Vacuum area and remove debris.
3. Protect cabinets, walls and painted surfaces with drop cloths or plastic.
4. Inspect power cord for damage.
Operating Instructions
1. Fill the solution tank.
2. If using the auto-ll and pump-out, connect one end of a ½” garden hose to the
top hose inlet in back of the machine, the other end to a faucet. Attach a second ½”
garden hose to the bottom hose inlet, and place the other end in a location where
dirty water can drain.
3. If manually lling and emptying the tank, keep both back hose inlets securely
capped.
4. In front, attach one end of a solution hose from a wand or other tool to the front
quick disconnect.
27
General Information
5. Attach one end of the vacuum hose from a wand or other attachment to the front
Cuff-Lynx™ vacuum hose port.
6. Plug in power cords.
• M-3 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1,
Pump and Heater 1. Using a second 20A grounded wall outlet on a separate circuit,
plug in the bottom cord to turn on Vac 2, Pump-out and Heater 2. The amber light
indicator on the switch plate will illuminate brightly when cords are plugged into two
separate circuits. Do not use extension cords longer than 50 feet.
• M-5 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1 and
Pump. Using a second 20A grounded wall outlet on a separate circuit, plug in the
bottom cord to turn on Vac 2 and Pump-out. The amber light indicator on the switch
plate will illuminate brightly when cords are plugged into two separate circuits. Do not
use extension cords longer than 50 feet.
• M-12 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1
and 2, and Pump-out. Using a second 20A grounded wall outlet on a separate circuit,
plug in the bottom cord to turn on the Pump-Mode for carpet and tile. The amber light
indicator on the switch plate will illuminate brightly when cords are plugged into two
separate circuits. Do not use extension cords longer than 50 feet.
• M-16 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1
and Vac 2. Using a second 20A grounded wall outlet on a separate circuit, plug in the
bottom cord to turn on Pump and Pump-out. The amber light indicator on the switch
plate will illuminate brightly when cords are plugged into two separate circuits. Do not
use extension cords longer than 50 feet.
7. Prime the pump by turning the valve to the Prime position and turning on the pump
for 30 seconds, then turn left to the Run position.
8. Turn on vacuum and pump switches. The Amber light left of the Pressure Gauge
will illuminate when cords are plugged into two separate circuits.
•M-3 - To use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on
Pump switch. Heater switch has three positions: Off (middle); 1,000 watts using one
heater (left); and 2,000 watts using two heaters (right). Red lights on panel display
indicate watts selected: one light = 1,000 watts; two lights = 2,000 watts; no lights =
heaters is off.
•M-5 – Turn on Vac 1 and Vac 2 switches. If using Pump-out feature, turn on Pumpout switch. To use pump, turn on the Pump switch.
•M-12 – Turn on Vac 1 and Vac 2 switches. If using Pump-out feature, turn on Pumpout switch. In carpet cleaning mode, a 220 PSI pump and solution heater are used.
The 220 PSI is not adjustable. Adjusting the regulator in this mode will not affect
the pump pressure. Two red lights left of switches will appear when Carpet mode is
activated. In Tile cleaning mode, a 1200 PSI pump will be used. Pump pressure is
set using the regulator on the front of the unit. There is no heat in Tile mode. It is not
possible to run the heater and 1200 PSI pump simultaneously.
•M-16 – Turn on Vac 1 and Vac 2 switches. To use Pump-out feature, turn on
Pump-out switch. To use pump, turn on Pump switch.
9. To adjust water pressure, turn the pressure regulator, located on the lower front
of the extractor, to the right to increase water pressure. Turn to the left to decrease
water pressure. Level will be visible on the pressure gauge.
10. Begin cleaning. Make two dry passes to every wet pass. Work away from cords
to avoid damage. To clean heavily soiled areas, repeat cleaning from different
directions.
11. Use a foam control solution in the recovery tank to prevent vacuum motor damage and check for foam build-up in recovery and solution tanks.
12. When not using the Auto Pump-out and using the recovery tank, an internal ball
oat will automatically stop the vacuum when tank lls. Empty the tank by using the
rear drain valve.
13. Relieve water pressure from the solution hose before disconnecting it, squeeze
the tools trigger ve seconds after turning the power switches off.
14. Once machine is off unplug power cords. Remove solution and vacuum hoses.
To empty the recovery tank, if Pump-out is not used, attach the 45˚ drain elbow to the
drain sprout in back. Lift up the dump valve to empty the tank.
15. To empty remaining water in the solution tank, turn the Prime Valve to the right
and turn on pump to move water into the recovery tank. Empty recovery tank.
After Use
1. Before storing machine, drain, rinse and dry tanks and vacuum hose of water
and solution.
2. Store in a dry area in the upright position.
3. Open recovery tank cover to promote air circulation.
4. Make sure the machine and solution system are completely drained and dry.
Trouble Shooting
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker. Reset circuit breaker, other items should not run on the
same circuit as the machine. Must be two 20-amp circuit outlets.
Pump does not work properly
1. Snap quick disconnects rmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and ush clean.
4. Filters clogged, remove lters and rinse clean with water.
5. Heater is blocked; ush out with Mytee’s
6. If brass check valve is stuck, replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate may need to be replaced.
9. If pump motor brushes are worn, replace pump.
M-3 or M-12 heater does not work properly
1. If sensor mounted on the heater has popped, reset sensor by pushing in button.
2. Heating element may need to be replaced.
Vacuum motor does not work properly
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Secure the vacuum tank tightly.
4. If ball oat is shut off, empty vacuum tank of all wastewater.
5. Make sure ball oat is rmly installed on the elbow.
6. If water is coming out of the vacuum motor, use a low foaming detergent.
7. Clean upholstery tool or oor wand jets.
®
System Maintainer.
Maintenance Schedule
Latches are located in back to open tank for internal maintenance. To keep machine
in good working condition, follow machine’s daily and weekly maintenance proce-
dures. Check valves and relief valves should be replaced annually.
Maintenance item
Flush pump-out with clear water.
Clean and inspect tanks.
Clean and inspect hoses.
Check and clean internal lters by twisting off, rinsing
with clean water and replacing.
Check power supply cable.
Clean machine with all-purpose cleaner and cloth.
Check spray nozzles.
Flush solution system with Mytee
Remove and oat shut-off screen from tank and clean.
Simply pull off.
Inspect vacuum hoses for holes and loose cuffs.
Inspect spray pattern for clogging. If clogged, remove
spray tips and soak them in a recommended liquid
neutralizer for up to six hours. To remove spray tip,
twist spray tip body counter-clockwise.
Lubricate wheels with water resistant oil.
Inspect machine for water leaks and loose hardware.
®
System Maintainer.
Daily
x
x
x
x
x
x
Once a week
x
x
x
x
x
x
x
FAQs
Q: How much do the M-Series™ Extractors weigh and what are dimensions?
A: M-3:
Machine Weight – 147.2 lbs.
Shipping Weight – 179.2 lbs.
Machine Dimensions – 35 1/4” x 19 1/2” x 43”
Shipping Dimensions – 37 1/4” x 21” x 50 3/4”
M-5:
Machine Weight – 141 lbs.
Shipping Weight – 172.6 lbs.
Machine Dimensions – 35 1/4” x 19 1/2” x 43”
Shipping Dimensions – 37 1/4” x 21” x 50 3/4”
M-12:
Machine Weight – 168 lbs.
Shipping Weight – 200 lbs.
Machine Dimensions – 35 1/4” x 19 1/2” x 43”
Shipping Dimensions – 37 1/4” x 21” x 50 3/4”
M-16:
Machine Weight – 152 lbs.
Shipping Weight – 183.6 lbs.
Machine Dimensions – 35 1/4” x 19 1/2” x 43”
Shipping Dimensions – 37 1/4” x 21” x 50 3/4”
Q: What comes standard with M-Series™ Extractors?
A: Hose hanger with four screws, two Cuff-Lynx™ Model Nos.: H141 Reducer and
H110 Coupler Swivel and 45˚ drain elbow.
®
Q: Does Mytee
A: All upholstery tools, wands and Spinners
recommend tools for this machine?
®
can be used with the M-Series™.
28
General information
Q: Where do I plug the machine in?
A: Into two separate 20A grounded circuits.
Q: How will I know when I nd two separate circuits?
A: The amber indicator light on the switch plate will illuminate when the power cords
are plugged into two separate circuits.
Q: Are pumps rebuildable for the M-Series™?
A: For a 1200 PSI pump, available rebuildable kits are: RK0034 seal & piston kit,
RL0038 valve & o-ring kit, and RL0033 cam & bearing kit. For a 500 PSI pump,
available rebuildable kits are: RK0022 seal & piston kit, RL0023 valve & o-ring kit
and RK0024 cam & bearing kit.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off. You should also run Mytee’s
through the system to keep the hoses, pump, and heater clean and free of debris.
®
System Maintainer
Warranty
MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and product support
to its customers and therefore backs up all of its new products purchased from Mytee
Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this
lifetime limited warranty. This limited warranty begins on the date of the customer’s
purchase and is valid and available to the original purchaser with proof of purchase,
and is not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.
HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotationally-molded housings will be free from manufacturing defects. This warranty covers
the cost of replacement or repair only and does not cover shipping or labor costs.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for
90 days from the date of original purchase. “Wear parts” are items which wear out
as a result of usage or the passage of time and are consumed despite attempts to
maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals,
hoses, switches, thermostats, plastisol parts, lters, bearings, brushes, solenoids,
o-rings, bulbs, heating elements, castors, or other parts deemed wear items in
Mytee’s sole discretion. This warranty covers the cost of replacement only and does
not cover shipping or labor costs.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY,
EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT
ANY TIME WITHOUT NOTICE.
then the remaining provisions and portions shall remain valid and enforceable.
If any provision or portion of this limited warranty policy is found to be limited by law,
then that provision or portion shall be construed to make it effective within the
bounds of law. For example, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have the minimum duration
required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible without
violating the law.
The validity, construction and performance of this warranty policy shall be governed
by the laws of the State of California, without respect to conicts of laws principles.
The exclusive jurisdiction of any legal action arising from or related to this warranty
policy shall be in the State of California and no legal action shall be commenced
elsewhere.
Return Material Authorization Procedure
It is the responsibility of any Authorized Service Center (ASC) or Distributor with
written authorization to ensure the Customers equipment is repaired as soon as
possible. Only Mytee Products Inc. or it’s authorized dealers with written authorization, service centers, and agents may make warranty repairs on these products. All
others do so at their own risk and expense.
The Distributor must follow Mytee Products, Inc. standard RMA procedure:
1. When a repair falls within the Warranty time period for a piece of equipment, the
Distributor will ll out a RMA/Warranty claim form. This form will act as a repair order
to replace any defective parts.
2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim
form for evaluation at the customer’s expense. This shipping is non-refundable. All
warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if
warranty will be approved. Any credit for repair and/or parts will only be issued upon
evaluation and approval from Mytee Products, Inc.
3. When Warranty is approved, the Distributor’s account will be credited for the
replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s)
to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be
credited for any parts sent for this claim.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR
OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER
ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO
EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.
All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication, improper installation, abuse, lack of maintenance,
negligence in use or care, abnormal use, alteration of design, modication, use of
incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor
or service center. Mytee may make changes in products it manufactures and markets
at any time; these changes are made without obligation to change, retrot, or upgrade any product previously sold or manufactured.
Mytee has no obligation to honor the limited warranties set forth herein unless the
original purchaser, promptly upon discovering the warranty claim and prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service
center to describe the claim and to receive and follow instructions for documenting
and resolving the claim. In addition, the purchaser must provide the product to which
the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the product intact,
unmodied, with all of its original parts.
If any provision or portion of this limited warranty policy is found to be unenforceable,
29
NOTES
30
Mytee Products I nc.
13655 Stowe Dr.
Poway, Ca. 920 64
www.my tee.com
PH 85 8.679.1191
F X 858.6 79 .7814
© 2012 Mytee Pro ducts In c.
Print ed in the U.S.A.
Loading...