Mytee Spyder HP60, HP100 Grand Prix Instructions Manual

Instructions for

HP60 Spyder

Please read before use.

Register your product
at www.mytee.com/help

™

Set up p. 3
General information p. 6
Parts & pricing p. 9
Wiring diagram p. 11
Notes p.12

Model #

Serial #

Form # ADM-HP60

6-11

13655 Stowe Dr., Poway, Ca. 92064

1

2

HP60 SPYDER™

6

1. Waist high controls

2. 2” Male Cuff-Lynx™

3. Female quick disconnect

4. Solution tank

5. Blower attachment

6. Solution tank lid

FRONT

BACK

1

7

2

3

12

4

11

5

8

10

9

7. Easy open lid

8. Motor base housing

9. Locking casters

10. Vent guard

11. Single 25’ power cord

12. Bucket-high drain valve

ACCESSORIES

8400- 3” Stainless Steel H122-Cuff-Lynx™
Upholstery Tool 1/1/4” reducer

8501- 15’ 1-1/4” Vac/Sol Hose H375- Hose Hanger

FILL SOLUTION TANK

Lift lid to ll. For best results, ll with warm water (140° F).

3

HP60 SPYDER™

ATTACH HOSES

Attach one end of a solution hose to a wand or other tool, the
other end to the Spyder’s™ front quick disconnect. Attach one
end of a vacuum hose to the tool, the other end to the Spyder’s™
Cuff-Lynx™ vacuum hose port.

PUMP

VACUUM PUMP HEATER

After the machine has been plugged into a 20 amp grounded
outlet, turn on pump. Key tool until upholstery tool releases a
steady ow.

HEATER

VACUUM PUMP HEATER

Release tool trigger. Turn on heater. Wait 8 – 10 minutes for unit
to pre-heat. Once heated, re-key upholstery tool until hot water
begins owing. Once hot water is owing, release trigger and
pre-heat an additional 4 – 5 minutes.

VACUUM MOTOR

VACUUM PUMP HEATER

Turn on vacuum motor and begin cleaning. For best results
make two dry passes to every wet pass.

4

ENGLISH

HP60 SPYDER™

BLOWER ATTACHMENT

Connect blower attachment for drying (optional).

RECOVERY TANK

.

Add a defoamer in the recovery tank to reduce foam, prolonging
the life of the Spyder™ vacuum motor .

45 DEGREE SPOUT DRAIN

When the oat shuts off vacuum, empty tank. Pull lever located at
the back of the machine to release water.

MYTEE® SYSTEM MAINTAINER

Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.

5

GENERAL INFORMATION

Dear Customer:

Congratulations on the purchase of your new HP60 Spyder™. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.

Keep in mind that the HP60 Spyder™ is a machine, so neglect or abuse
will cause unnecessary damage and void the warranty. However with simple
maintenance the HP60 will give quality performance for many years to come.

If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com

Before you begin cleaning, please read your manual thoroughly.

Sincerely,
Mytee Customer Care Dept.

Grounding Instructions

This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must
be plugged into an appropriate outlet that is properly installed in accordance with all
local code and ordinances. Do not remove ground pin; if missing, replace plug before
use.

Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualied electrician or service person if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the machine. If it will not t the outlet, have a proper outlet installed by a qualied
electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualied electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.

DO NOT use extension cords.

Please Note for America use only

Grounding Pin

Figure 1

Grounded Outlet

Metal
Screw

Grounded Outlet Box

Figure 2 Figure 3

Adapter

Tab for Grounding
Screw

Parts and Service

Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.

Name Plate

The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.

Unpacking the Machine

When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to le a
freight damage claim.

Caution and Warnings

Symbols

Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.

Is used to warn of immediate hazards that will cause severe personal injury or death.

Is used to call attention to a situation that could cause severe personal injury.

Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.

To reduce the risk of re, electrical shock, or injury:

1. Read all instructions before using equipment.

2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.

3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.

4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.

6. Do not run appliance over cord. Keep cord away from heated surfaces.

7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.

8. Do not use outdoors or on wet surfaces and or standing water.

9. Always unplug or disconnect the appliance from power supply when not in use.

10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.

11. Do not use in areas where ammable or combustible material may be present.

12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.

13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.

14. Keep hair, loose clothing, ngers, and all parts of the body away from all
openings and moving parts.

15. Use extra care when cleaning on stairs.

16. To reduce the risk of re or electric shock, do not use this machine with a solid­state speed control device.

17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.

18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alka­lines, or other dangerous liquids.

19. Do not leave operating unattended.

Filling the Solution Tank

1. Fill the solution tank with the approved cleaning solution.

2. Do not ll up the solution tank completely: 1” should be left free at the top.

3. Typically, the solution should be a mixture of water and a cleaning chemical
appropriate for the type of job.

4. Always follow the dilution instructions on the chemical container label.

5. The temperature of the cleaning solution must not exceed 70

Use only non-ammable liquid in this machine.

o

C/160oF.

6

GENERAL INFORMATION

Setup

1. Open lid of solution tank. Fill solution with water or approved cleaning agent. For
best results, ll with warm water (140

o

).

Flammable materials can cause an explosion or re. Do not use ammable solutions
or materials in tank(s).

FOR SAFETY: When using machine, follow mixing and handling instructions on
chemical containers.

ATTENTION: If using powdered cleaning chemicals, mix prior to adding.

2. Attach solution hose (located front of machine). NOTE: Make sure the quick
disconnect snap together rmly. As you do this, always inspect hoses for cracks or
fraying. Do not use if hoses are damaged.

3. Attach other end of solution hose to wand.

4. Attach vacuum hose to recovery tank.

5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate
machine unless cord is properly grounded. FOR SAFETY: Do not operate machine
with the use of an extension cord.

6. Turn on pump. Key tool until you have a steady ow.

7. Release tool trigger. Turn on heater.

8. Wait 8–10 minutes for unit to pre-heat.

9. Re-key upholstery tool until hot water begins owing.

10. Once hot water is owing, release trigger and pre-heat an additional 4–5 minutes.

11. Turn on vacuum motor.

12. Begin cleaning. Make two dry passes to every wet pass.

13. For oor cleaning, unplug tool and attach oor wand.

14. Work away from cords to avoid damage.

15. Use a defoamer in your recovery tank.

16. To clean heavily soiled areas, repeat cleaning from different directions.

17. When oat shuts off vacuum, empty tanks.

18. When work is complete, unplug cords and hoses.

19. Wrap and clean hoses. Clean all tanks.

Pre-Operation

1. Vacuum carpet and upholstery and remove other debris.

2. Perform machine setup procedures.

3. Inspect power cord for damage.

Operation

1. Turn pump switch on.

2. Pull up on tool lever to release air in the line. Hold lever until a steady ow of water
comes out of the wand.

3. Once pump is primed and there is pressure in the solution line, turn on heater switch
(if model is equipped with heater) and wait a few minutes for water to heat up.

4. Once water is heated, turn on vacuum and begin cleaning.
Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.

1. Work away from outlet and power cord to prevent cord damage.

2. Use a recommended foam control solution in the recovery tank to prevent vacuum
motor damage. Periodically check for excessive foam buildup in solution tank, and
recovery tank.

3. To clean heavily soiled areas, repeat cleaning path from different direction.

4. When ball oat shuts off vacuum, it is time to empty the dirty water from the
recovery tank, and rell solution tank.

5. After cleaning, relieve water pressure from tool before disconnecting hose.
Squeeze trigger for ve seconds after turning main power switch off.

After Use

1. Unplug.

2. Empty solution tank and rinse it with clean water.

3. Inspect hoses and replace if damaged.

4. Inspect solution lter. Clean or replace if damaged.

5. Store the machine in a clean, dry place.

6. Open recovery tank cover to promote air circulation.

Maintenance Schedule

Maintenance item Daily Once a week

Clean and inspect Tanks
Clean and inspect Hoses
Check lters
Check power supply cable
Clean machine with all purpose cleaner and cloth
Check spray nozzles
Flush solution system with Mytee system maintainer
Remove and clean oat shut-off screen from tank
Inspect vacuum hoses for holes and loose cuffs

x
x
x
x
x

x
x
x
x

Trouble Shooting

There is no power.

1. Plug machine in proper outlet.

2. Check circuit breaker; reset circuit breaker, other items should not run on the
same circuit as machine. Outlet must be a 20-amp circuit.

Pump does not work properly.

1. Snap quick disconnects rmly together.

2. Check solution tank; may be empty.

3. Jets clogged, remove jet and ush clean.

4. Filters clogged, remove lters and rinse clean with water.

5. Heater is blocked; ush out with Mytee’s system maintainer.

6. If brass check valve is stuck replace valve.

7. Check pump wire. May need to reconnect wire.

8. Switch plate switch may need to be replaced.

9. If pump motor brushes are worn, replace pump.

Heater does not work properly.

1. If sensor mounted on the heater has popped, reset sensor by pushing in button.

2. Heating element may need to be replaced.

Vacuum motor does not work properly.

1. Check that hose is tightly connected.

2. Close drain hose valve completely.

3. Secure the vacuum tank tightly.

4. If ball oat is shut off, empty vacuum tank of all wastewater.

5. Make sure ball oat is rmly installed on the elbow.

6. If water is coming out of vacuum motor, use a low foaming detergent.

7. Clean upholstery tool or oor wand jets.

Accessories (optional)

2200 Airmover
3601 System Maintainer
2700 Mytee-Dry
8700 Crevice Tool

HP-Dry Vehicle Drying Kit

FAQs

Q: How much does the HP60 weigh and what are the shipping dimensions?

A: 69 Pounds - Box dimensions are 28 1/2” x 17 1/4” x 35 3/4”.
Must ship motor freight.

Q: What comes standard with the HP60?

A: The HP60 comes with a hose hanger ( H375 ), a 25’ 12/3 Cord, 15’ 1-1/4”
Vacuum/Solution Hose ( 8501 ), Cuff-Lynx™ 1-1/4” reducer ( H122 ) and a
3” Stainless Steel Upholstery Tool ( 8400 ).

Q: Does Mytee recommend a tool for the machine?

A: A variety of tools can be used with the unit, including our 8390 wand, 8700 crevice
tool, and 8400 upholstery tool. Also our HP-Dry kit can be used for drying interiors
and exteriors.

Q: Where do I plug the machine in?

A: The HP60 requires a 20A grounded circuit. Please note: GFI outlets may trip
before the breaker setting.

Q: What is the proper pre heat cycle for the HP60?

A: Turn pump switch to the on position and prime pump through the solution hose
and the tool. Then turn the heater switch to the on position. Let the machine sit idle
for 8-10 minutes. Spray tool until you feel the hot water from the jet. Let machine sit
idle for an additional 3-5 minutes. This will insure the water in the heater and hoses
will be at the hottest point to start cleaning.

7

GENERAL INFORMATION

Q: Are the pumps re-buildable for the HP60?

A: Yes, both the seals and the pistons have repair kits available.
Please see the pump manual that shipped with your machine for the
maintenance schedule.

Q: Is there anything I can do to increase the expected life of my machine?

A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off. You should also run a System Maintainer through
the system to keep the hoses, pump, and heater clean and free of debris.

Warranty

MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and product support
to its customers and therefore backs up all of its new products purchased from Mytee
Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this
lifetime limited warranty. This limited warranty begins on the date of the customer’s
purchase and is valid and available to the original purchaser with proof of purchase,
and is not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.

HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotation­ally-molded housings will be free from manufacturing defects. This warranty covers
the cost of replacement or repair only and does not cover shipping or labor costs.

WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for
90 days from the date of original purchase. “Wear parts” are items which wear out
as a result of usage or the passage of time and are consumed despite attempts to
maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals,
hoses, switches, thermostats, plastisol parts, lters, bearings, brushes, solenoids, o­rings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s
sole discretion. This warranty covers the cost of replacement only and does not cover
shipping or labor costs.

PUMP, VACUUM MOTOR AND HEATER TWO-YEAR LIMITED WARRANTY: Mytee
warrants that pumps, vacuum and oor machine motors, and heaters will be free
from manufacturing defects, defects in workmanship, and defects in material for two
(2) years from the date of original purchase. This warranty does not apply and is void
if the pump, vacuum motor, or heater has worn brush motors, water damage, chemi­cal build-up, chemical damage, or evidence of abuse, neglect or tampering. This
warranty covers the cost of replacement or repair only and does not cover shipping
or labor costs.

HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY,
EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGE­MENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIM­ITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT
ANY TIME WITHOUT NOTICE.

If any provision or portion of this limited warranty policy is found to be unenforceable,
then the remaining provisions and portions shall remain valid and enforceable.
If any provision or portion of this limited warranty policy is found to be limited by law,
then that provision or portion shall be construed to make it effective within the
bounds of law. For example, if there are legal limitations on the duration of warran­ties, the warranties made herein shall be construed to have the minimum duration
required by law, or, if there are legal limitations of exclusion of remedies, the exclu­sions made herein shall be construed to apply to the fullest extent possible without
violating the law.

The validity, construction and performance of this warranty policy shall be governed
by the laws of the State of California, without respect to conicts of laws principles.
The exclusive jurisdiction of any legal action arising from or related to this warranty
policy shall be in the State of California and no legal action shall be commenced
elsewhere.

Return Material Authorization Procedure

It is the responsibility of any Authorized Service Center (ASC) or Distributor with
written authorization to ensure the Customers equipment is repaired as soon as
possible. Only Mytee Products Inc. or it’s authorized dealers with written authoriza­tion, service centers, and agents may make warranty repairs on these products. All
others do so at their own risk and expense.

The Distributor must follow Mytee Products, Inc. standard RMA procedure:

1. When a repair falls within the Warranty time period for a piece of equipment, the
Distributor will ll out a RMA/Warranty claim form. This form will act as a repair order
to replace any defective parts.

2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim
form for evaluation at the customer’s expense. This shipping is non-refundable. All
warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if
warranty will be approved. Any credit for repair and/or parts will only be issued upon
evaluation and approval from Mytee Products, Inc.

3. When Warranty is approved, the Distributor’s account will be credited for the
replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s)
to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be
credited for any parts sent for this claim.

LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR
OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER
ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO
EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.

All limited warranties are void for, and Mytee does not warrant in any way, any prod­uct that evidences misapplication, improper installation, abuse, lack of maintenance,
negligence in use or care, abnormal use, alteration of design, modication, use of
incompatible or corrosive chemicals, use in a rental service, and/or servicing, installa­tion of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor
or service center. Mytee may make changes in products it manufactures and markets
at any time; these changes are made without obligation to change, retrot, or up­grade any product previously sold or manufactured.

Mytee has no obligation to honor the limited warranties set forth herein unless the
original purchaser, promptly upon discovering the warranty claim and prior to continu­ing to use the product, contacts Mytee or a Mytee authorized distributor or service
center to describe the claim and to receive and follow instructions for documenting
and resolving the claim. In addition, the purchaser must provide the product to which
the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the product intact,
unmodied, with all of its original parts.

8

CHECKED

DRAWN

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS PROHIBITED.

HP60 SPYDER™ PARTS & PRICING

MSRP

1 $3.49 ea

1 $17.99 ea

2 $0.99 ea

QTY.

DESCRIPTION

qd, brass, 1/4" f

washer, nylon, 9/16id x 1-1/16od x .031

$4.99/ft

1

1 $8.99 ea

1 $19.99 ea

1 $25.99 ea

1 $9.99 ea

1 $117.99 ea

vac tank, spyder

bracket, rear, fb/spy

6 $0.99 ea

float, 1.5", ball style

elbow, U, 180, 1-1/2", float

screw, #8 x 5/8 phil oval, s/s

PIPE, PVC, 1-1/2" x 7-1/2" LG.

hose, 3/8" x 9" (OAL), f x f, surge, 1600psi

adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex

B111

PART NO.

NO.

ITEM

B102

H413

AH157

61

62

63

64

H912

65

P793

66

P755

PH633-6

68

67

H235

69

H304

70

MSRP

2 $17.99 ea

QTY.

2 $0.99 ea

6 $0.99 ea

1 $29.99 ea

2 $49.99 ea

10 $0.99 ea

2 $78.99 ea

2 $16.49 ea

6 $4.49 ea

1 $26.49 ea

1 $14.99 ea

1 $20.99 ea

1 $3.19 ea

2 $6.99 ea

1 $28.99 ea

1 $9.99 ea

lid, vac, 6", clear

elbow, inlet assy 1-1/2"

gasket, vac lid, 6.5" i.d 7.5" o.d

A925

G056

G060

71

72

73

1 $23.99 ea

3 $13.99 ea

valve, drain, 1-1/2"

spout, drain, 45 degree

switch, rocker, 2 position

bracket, "L" (all extracters)

E515

H225

H226

H390A

74

75

76

77

1 $27.99 ea

1 $4.99 ea

1 $151.99 ea

MSRP

1 $6.99 ea

4 $0.99 ea

QTY.

DESCRIPTION

plate, switch, ml/trkr, 3 hole

screw, #10-32 x 1/2" SHCS, alloy

H636

H389

78

79

$0.99ea

4 $0.99 ea

24

$8.99/ft

1 $9.49 ea

1

ITEMS NOT SHOWN:

PART NO.

4 $1.99 ea

1 $3.49 ea

2 $4.99 ea

1 $9.99 ea

2 $4.99 ea

2 $10.99 ea

filter, bag, vac tank

hanger, wire formed, hose

gasket, strip, 3/4" x 36" x 1/8"

H375

G085

G010

$6.49/ft

$8.99/ft

$4.99/Ft

1 $14.99 ea

1

3 $1.49 ea

1

1

1 $5.99 ea

1 $140.99

1 $8.99 ea

11 $0.99 ea

1 $7.99 ea

3 $4.99 ea

3 $0.99 ea

3 $0.99 ea

1 $52.99 ea

21 $0.99 ea

1 $3.19 ea

1 $1.99 ea

1 $106.99 ea

8 $0.99 ea

2 $2.99 ea

3 $5.99 ea

1 $2.99 ea

4 $14.99 ea

16 $0.99 ea

1 $103.99 ea

1 $0.99 ea

3 $0.99 ea

2 $0.99 ea

2 $1.99 ea

1 $0.99 ea

2 $0.99 ea

1 $3.99 ea

2 $0.99 ea

1 $3.99 ea

6 $0.99 ea

3 $3.19 ea

DESCRIPTION

nut, kep, #10-32 zinc

screw, 10-32 x 1/2 phil pan

bracket, heater mounting, dual

H528

H273

H230

PART NO.

3

1

2

NO.

ITEM

heating rod, 600W, 115V

Thermostat, 200°, Auto, 1/4"

Thermostat, 310°F ± 10°F, Manual, 1/4"

screw, 6 x 3/16, phil pan head, self tapping

elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt

valve, brass, 1/4" check 1 $13.99 ea

hose, 3/8" x 14-1/2" (OAL), f surge

elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt 1 $5.99 ea

sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi

hose, 3/8" x 6.5", (OAL), f x fsw, surge, 1600psi

heater, aluminum cast, single w/wrap & drilled holes

E574

E573

E571

4

H274

5

B103

B207

AH156

AH108S

10

11

B108

AH184

12

13

14

H903A

6

7

9

8

washer, 1/4" flat, s/s

bushing, brass, 3/8"mpt x 1/4" 2 $3.19 ea

pump, 120psi, demand, 115V

elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt

elbow, brass, 90 deg, 1/2" barb x 3/8"mpt

screw, 10-32 x 1-1/4", phil flat full thread, black oxide

C305

17

H210

18

H185

19

B172

20

B136

15

B105

16

pipe, pvc, 1-1/2"

sol hose, 1/2" kuri 100psi

clamp, hose, 5/16-29/32

clamp, hose, 2-1/4 dia

adapter, pvc, 1-1/2" fms x fmpt

cuff, black 1-1/2"

vac hose, 2", wire reinforced

manifold, single vac, no gasket

vac hose, 1-1/2", wire reinforced

adapter, brass, 1/2" barb x 3/8" fsw, ball end

H347

PH615-22

21

22

B160

23

H244

24

H217

PH633-03

26

25

P735

PH628-18

27

28

H300

PH627-24

30

29

gasket, vacuum motor

vac support, 3 stage, 4-1/16"

plate, single manifold, 6.5" x 9"

bolt, 1/4-20 x 1-3/4" hex head, s/s

bolt, 1/4-20 x 1/2" serrated hex flange, zinc

G004

33

H501

34

H330

35

H204

36

H770

C302 vac motor, 3 stage, 120V, tangential

32

31

fitting, strain relief, cord

nut, lock, 10-32, thin pattern

power cord, end, 25', 12/3 black

bolt, 1/4-20 x 3/4" serrated hex flange, zinc

E531

H458

H220

H768

38

39

40

37

9

base, spyder

nut, lock, 1/2" steel

P791

H221

41

42

gasket, inlet, 1.80" i.d.

guard, cooling fan, wire

fitting, inlet, pvc, 1-1/2", gray

screw, #10 x 5/8" hex head, zinc

H343

H296

H229

G001

43

44

45

46

sol tank, spyder

nut, hex, 1/4-20 s/s

washer, 1/4" lock, s/s

washer, 1/4"id x 1"od, flat, s/s

bolt, 1/4-20 x 3/4" hex head, s/s

caster, 3", Black Hub, Gray Tread

P792

H215

H202

H667

50

47

48

49

bolt, 1/4-20 x 1-1/4" hex head

washer, buna 1-1/8" od x 3/16" id

H213

H211

H203

G052

51

52

53

54

Part prices are subject to change.Order parts at: http://www.mytee.com/products/product.php?id=HP60

filter, strainer, 1/4"

bracket, front, kodiak

bolt, 1/4-20 x 1-1/2" hex head, s/s

bolt, 1/4-20 x 1/2", hex head, zinc

B119

H316

55

H379

56

B107 nipple, brass, 1/4"m, hex

H201

H212 washer, 9/16"id x 1"od, flat, s/s

57

58

59

60

HP60 SPYDER™ PARTS & PRICING

D

C

B

A

1

2

3

4

5

6

7

8

E

F

HP60

SHEET 2 OF 2

Spyder

SCALE: 1:5

REV

DWG. NO.

D

SIZE

TITLE:

NAME

DATE

CHECKED

DRAWN

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS PROHIBITED.

mytee

PRODUCTS, INC.

858-679-1191

J. Cash

10/26/10

OD

DO NOT SCALE

DRAWING

73

72

71

70

69

75

74

46

45

66

45

77

78

79

76

32

32

68

24

67

9

65

32

9

59

63

60

32

59

59

60

64

63

59

61

To heater "OUT"

thru AH108S (#11)

62

54

52

53

52

53

50

51

32

36

35

34

33

49

31

37

38

28

26

30

29

26

27

39

40

41

56

38

18

55

58

57

51

18

59

60

16

To pump "IN"

thru B160 (#27)

59

9

17

1

18

15

19

16

20

21

22

23

To filter in sol tank

thru B103 (#9)

26

13

12

10

To female q.d.

thru B103 (#9)

25

24

14

To inlet on base

(#48)

42

38

18

45

9

11

9

43

44

48

47

9

8

7

4

1

2

3

6

5

10

1

2

3

1

Mytee Products

13655 Stowe Dr.

Poway, CA

92064

---1

HP60

0000 A

1/31/2011 4:44:13 PM

Z:\Engineering\GHI\GHI Projects\MYTEE\Mytee Schematics\HP60\HP60 Schematic.SCHDOC

Title

Size: Number:

Date:

File:

Revision:

Sheet of

Time:

Legal

HP60 SPYDER™ WIRING DIAGRAM

Heater 2

Green

White

Thermal Switch

GND

E571E571

L1 L2

Thermal Switch

SW-DPST

Orange

Green

White

White

Inline Conn.

White

Inline Conn.

Thermal Switch

Green

L2

Black

GND

L1 L2

Heater 1

C302

GND

Vacuum Motor 1

Thermal Switch

L1

Inline Conn.

Black

E515 E515

SW-DPST

Orange

SW-DPST

Yellow

E515

White

Green Green Green

GND

L1

L2

Inline Conn.

Green

White

Cord Input Primary

Entry Location, Top or Far Right

Black

Inline Conn.

C305

GND

L2

Pressure Pump

Black

L1

Switch

Pressure

Inline Conn.

Black

E515

SW-DPST

Blue

Black Black Black

11

NOTES

Mytee Product s I nc.
13655 Stowe Dr.
Poway, Ca. 9 20 64

www.my tee.com
PH 85 8.679.1191
F X 858.6 79.7814

© 2011 Mytee Pr oducts I nc.
Print ed in t he U.S.A .

12