Mytee 7300-SLA Air Hog Plus User Manual

Instructions for

7300-SLA Air Hog™ Plus

Please read before use.

Register your product
at http://www.mytee.
com/support/register

Set up p. 3
General information p. 9
Parts & pricing p. 12
Wiring diagram p. 14

Model #

Serial #

Form # ADP-7300

4-14

13655 Stowe Dr., Poway, Ca. 92064

1

2

7300-SLA AIR HOG™ PLUS

7300-SLA BACK7300-SLA FRONT

1

2

3

4

1. Clear “T” handle lid

2. Lint Hog™ lter housing

3. Base

4. 3” locking casters

5. Cooling fan

8

7

5

6. Recovery tank

7. Lift handle

8. 2” Male Cuff-Lynx™
starter

9

10

16

15

6

11

14

13

12

9. Lint Hog™ cap

10. Lint Hog™ lter

11. Switch plate

12. Vents

13. Dual cords

14. Pump-out

15. Cuff-Lynx™ plugs

16. Lift handle

7300-SLA ACCESSORIES

H136 - Coupler Swivel,

2” male x 2” female vac hose

H141 - Reducer,

2” female x 1.5” female vac hose

H110 - Coupler Swivel,

2” female x 2” female vac hose

FILTERS

G008 - Pack of Piglet™

lters

REPLACING HOSE CUFFS WITH CUFF-LYNX™

Twist clock-wise to remove standard cuffs.

Twist counter clock-wise to attach Cuff-Lynx™ to vac. hose.

Once you receive your Air Hog™ Plus, you will need to replace the
cuffs on your vacuum hose. To remove old cuffs, twist clock-wise.
To attach either male, female or reducer Cuff-lynx™ to vacuum
hose, twist counter clock-wise.

3

7300-SLA AIR HOG™ PLUS

PIGLET FILTER & MESH FILTER

Insert one of the Piglet™ lters over the mesh lter opening for
added protection. Once Piglet™ is added, insert mesh lter within
the Lint-Hog™.

To remove lter.

To insert lter.

7300-SLA POWER CORD

When the Lint Hog™ mesh lter lls up or you notice a change
in performance, empty the unit, clean the mesh lter and replace
Piglet™. Insert lter back in the Lint Hog™.

7300-SLA SWITCHES

Vac 1

Vac 2

Pump

out

Plug the power cord into a 20A grounded wall outlet to use
vacuum 1, vacuum 2 and pump-out.

7300-SLA VACUUM HOSE CONNECTION

Located on the side of the Air Hog™ Plus, are the vacuum
switches and pump-out switch. For vacuums, use vacuum

switches. Turn on the pump-out switch when using the
pump-out feature.

A vacuum hose attaches to the Lint Hog™ vacuum port in the front
of the machine, using its male Cuff-Lynx™ connection. You will
need a Cuff-Lynx™ coupler or reducer to attach the vacuum hose
to the Air Hog™ Plus.

4

7300-SLA AIR HOG™ PLUS

7300-SLA REAR VACUUM PLUGS

Cap top plug to use as
a ow through booster

Cap both plugs to be

used as a stand

alone extractor

Two vacuum plugs are located in the back. The top and bottom
rear plugs, depending on how they are capped, allow the Air
Hog™ Plus to be used as a stand-alone extractor, a ow-through
booster connected to another machine, or an in-line pump-out
unit. They also seal the Air Hog™ Plus vacuum tank.

Cap bottom plug

to used as booster

with pump-out

7300-SLA PUMP-OUT

Drain

Attach a garden hose to the back hose inlet to pump dirty water
from the tank. To use the pump-out, turn on the pump-out switch
located on the side of the machine. When the pump-out is not
in use, make sure the cap is on and securely tightened to
prevent leaks.

7300-SLA ELECTRONIC FLOAT SWITCH

Electronic

shut-off

switch

prevents water

from getting

into the

vacuum stack.

VAC STACK

The Air Hog™ Plus features an electronic oat switch inside the
recovery tank. When the switch is activated by rising water in
the recovery tank, the vacuum motors will automatically shut off.
This will help to prevent water from being sucked into the vacuum
stacks and damaging the motors.

7300-SLA CLEANING OF LINT HOG™, VAC STACK

& PUMP-OUT FILTER

Vacuum

stack lter

Lint Hog™

lter

Pump-out

lter

To clean the Lint Hog™ lter, twist off the cap and remove the
stainless steel mesh lter and rinse with water. Do not strike unit
against hard surface to remove debris, damage may result.
Remove top lid for access to vacuum stack and pump-out mesh
lters. Check often for debris build up. To clean, rinse with water
and put back.

5

7300-SLA AIR HOG™ PLUS

1. USING THE AIR HOG™ PLUS AS A STAND-ALONE LOW-PRESSURE EXTRACTOR

C

B

D

Drain

A

Solution ow

Dirty water recovery

Pump-out system

* Hoses & upholstery tool not included with Air Hog™ Plus

A. Connect one end of a solution hose to a faucet, and the other end to a cleaning tool. B. Connect a vacuum hose to the Air Hog™ Plus
front vacuum port, and to an accessory such as an upholstery tool. C. Cap both rear vacuum plugs. D. Let the tank ll until vacuum is
stopped by the electronic oat switch, or use the optional pump-out feature by attaching a garden hose to the Air Hog™ Plus back hose
outlet. Dirty water will automatically be pumped out. When the pump-out is not in use, make sure the cap is on and securely tightened to
prevent leaks.

2. USING THE AIR HOG™ PLUS AS A STAND-ALONE HIGH-PRESSURE EXTRACTOR

C

#2

Drain

A

D

#1

B

B

Solution ow

Dirty water recovery

Pump-out system

®

* Hoses, Spinner

A. Connect a pressure washer (#1), purchased separately, to a water source such as a faucet. B. Connect solution hose from a pressure
washer to a cleaning tool, bypassing the Air Hog™ Plus. Connect one end of the vacuum hose to the front of the Air Hog™ Plus and the other
end to an attachment such as a Spinner® (#2), purchased separately. C. Cap both rear vacuum plugs. D. Use the optional pump-out by
attaching a garden hose to the back hose outlet and turning the pump switch on. When the pump-out is not in use, make sure the cap is on
and securely tightened to prevent leaks. Water will rise until the electronic oat switch is activated.

& pressure washer not included with Air Hog™

6

7300-SLA AIR HOG™ PLUS

#1

A

Vac/sol hose typically 50 ft.

#2

3. USING THE AIR HOG™ PLUS AS A BOOSTER WITH PUMP-OUT

C

Drain

Solution ow

Dirty water recovery

Pump-out system

Base extractor airow

* Hoses, wand & extractor not included with Air Hog™ Plus

The optional pump-out can be used in conjunction with a second, larger extractor (#1), which will be used as a pressure source.
A. Connect a vacuum hose from the Air Hog™ Plus rear top plug to the large extractor’s vacuum inlet. Connect solution hose to the larger

extractor (#1) and your cleaning tool’s QD, a wand for example. Keep the bottom rear vacuum plug capped. B. Attach a vacuum hose to
the wand’s inlet and Air Hog™ Plus front vacuum port. C. To use the pump-out system, connect a garden hose to the back hose outlet.
Turn on the pump-out switch, and dirty water will be automatically pumped out of the machine.

B

4. USING THE AIR HOG™ PLUS AS A BOOSTER AND PASS-THROUGH EXTRACTOR

Solution ow

Dirty water recovery

* Hoses, wand & extractor not included with Air Hog™

#1

A

Vac/sol hose typically 50 ft.

C

#2

A

B

The Air Hog™ Plus (#2) can be used as a pass-through extractor and to boost the airow of a second, larger extractor (#1) by
increasing its CFM by 230. A. To use the larger extractor (#1) as a fresh water source and recovery tank, connect a vacuum hose to your

large extractor and the rear bottom plug of your Air Hog™ Plus. Then connect a solution hose from your larger extractor to the QD of your
cleaning tool (#2). B. Keep the top rear plug capped. C. Clean water will travel from the larger extractor through the cleaning tool to the
cleaning surface, and dirty water will be drawn through the Air Hog™ Plus into the main extractor’s recovery tank.

7

7300-SLA AIR HOG™ PLUS

5. USE THE AIR HOG™ PLUS AS A “DAISY CHAIN” WITH PUMP-OUT FEATURE

#2

Drain

E

Vac/sol hose

typically 50 ft.

#1

C

A

D

Solution ow

Dirty water recovery

Pump-out system

* Hoses, wand & pressure washer not included with Air Hog™ Plus

The Air Hog™ Plus (#1 & #2) can be connected by hoses as a “daisy chain”. Each unit will increase the total CFM by 230. A. To
connect two Air Hog™ Pluses along with a cleaning wand, connect one end of a garden hose to a faucet, the other end to a pressure washer.
B. Using a solution hose, attach the male QD to a pressure washer and female QD to your cleaning tool. C. Add a second Air Hog™ to the
daisy chain by connecting a vacuum hose from the front vacuum port of the #2 unit to the bottom rear vacuum port of the #1 unit. D. Attach
the wand’s vacuum hose to the front vacuum port and QD of the #1 Air Hog™ Plus. E. Attach a garden hose to the back hose inlet of the
#2 Air Hog™ Plus. Turn on the pump-out switch to the #2 Air Hog™ Plus. Dirty water will be pumped out of the machine.

B

6. CREATE A “DAISY CHAIN” USING TWO AIR HOG™ PLUS UNITS AND A LARGE EXTRACTOR

Solution ow

Dirty water recovery

* Hoses, wand & extractor not included with Air Hog™ Plus

D

Large extractor

Vac/sol hose

typically 50 ft.

A

A. To operate using this set-up, use the large extractor as a fresh water source and recovery tank, connect a vacuum hose to the large
extractor and the Air Hog™ Plus’ (#1) rear bottom plug. B. Add an additional Air Hog™ Plus (#2) to the daisy chain by attaching a
vacuum hose from the #1 Air Hog™ Plus to the #2 unit’s bottom rear plug. C. Connect a vacuum hose from the front vacuum port of the
#2 machine to the cleaning tool. D. To attach a wand, connect a solution hose to the large extractor. Connect a vacuum hose to the front
vacuum port of the #2 Air Hog™ Plus. Clean water will travel from the large extractor through the wand to the cleaning surface, and dirty
water will be drawn into the large extractor’s recovery tank.

#2

Vac/sol hose

typically 50 ft.

#1

C

B

8

GENERAL INFORMATION

Dear Customer:

Congratulations on the purchase of your new 7300-SLA Air Hog™ Plus. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior quality
and technology.

Keep in mind that the Air Hog™ Plus is a high performance machine, so neglect or
abuse will cause unnecessary damage and void the warranty. However, with simple
maintenance the 7300-SLA Air Hog™ Plus will give quality performance for many
years to come.

If warranty questions arise, please consult user manual or get in touch with your
distributor. If you have questions about maintenance, replacing parts or ordering
parts, please call an authorized Mytee Products Inc. Service Center. To see an
updated list, visit our website at www.mytee.com

Before you begin using, please read your manual thoroughly.

Sincerely,
Mytee Customer Care Dept.

Grounding Instructions

This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed in accordance
with all local code and ordinances. Do not remove ground pin; if missing, replace
plug before use.

Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualied electrician or service person if you are in
doubt as to whether the outlet is properly grounded. Do not modify the plug provided
with the machine. If it will not t the outlet, have a proper outlet installed by a
qualied electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualied electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.

Please note for America use only

Grounding Pin

Figure 1

Grounded Outlet

Metal
Screw

Grounded Outlet Box

Figure 2 Figure 3

Adapter

Tab for Grounding
Screw

Parts and Service

Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the model and serial number
when discussing your machine.

Name Plate

The model and serial number of your machine are shown on the name plate located
on the back of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the model and
serial number of your machine for future reference.

Unpacking the Machine

When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to le a
freight damage claim.

Caution and Warnings

Symbols

Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.

Is used to warn of immediate hazards that will cause severe personal injury or death.

Is used to call attention to a situation that could cause severe personal injury.

Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.

To reduce the risk of re, electrical shock, or injury:

1. Read all instructions before using equipment.

2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.

3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.

4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.

6. Do not run appliance over cord. Keep cord away from heated surfaces.

7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.

8. Do not use outdoors or on wet surfaces and or standing water.

9. Always unplug or disconnect the appliance from power supply when not in use.

10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.

11. Do not use in areas where ammable or combustible material may be present.

12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.

13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.

14. Keep hair, loose clothing, ngers, and all parts of the body away from all
openings and moving parts.

15. Use extra care when using on stairs.

16. To reduce the risk of re or electric shock, do not use this machine with a
solid-state speed control device.

17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.

18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid,
alkalines, or other dangerous liquids.

19. Do not leave operating unattended.

Pre-Operation

1. Remove furniture and other items from the area you are going to clean.

2. Vacuum area and remove debris.

3. Protect cabinets, walls and painted surfaces with drop cloths or plastic.

4. Inspect power cord for damage.

Operating Instructions

1. Plug into two separate circuit 20-amp, grounded circuits. Non GFI recommended.

2. When using the vacuum, turn on the vacuum switch.

3. When using the pump-out, turn on the pump-out switch.

4. When using a wand or other vacuum attachment, or using the Air Hog™ Plug as
a standalone extractor, connect the vacuum hose to the front vacuum port in the
on-board Lint Hog™ lter. A Mytee Cuff-Lynx™ coupler or reducer will be needed.

5. Connect the vacuum hose to the Air Hog™ Plus vacuum inlet.

6. When using the auto pump-out, attach a garden hose to the hose outlet, located
on the back of the unit.

9

GENERAL INFORMATION

7. If auto pump-out is not used, let the tank ll until the electronic oat switch stops
the tank from lling. Empty tank.

8. When using with other machines, connect vacuum hose to one of two back
vacuum ports (depending on usage), and solution hose from your base extractor to
your cleaning tool.

After Use

1. Unplug.

2. Empty solution tank, if needed, rinse with clean water and dry.

3. Clean internal lters:
Pump-out lter - Remove lid on top of tank. Reach into tank and twist off pump-out
lter using a counter-clockwise motion. Rinse and dry, replace and close lid.
Vacuum stack lter - Remove lid on top of tank. Reach into vacuum stack and
remove round, mesh lter. Rinse and dry, replace and close lid.

4. Clean external Lint Hog™ lter on top of tank. Twist off housing lid. Remove stain­less steel lter. Rinse to clean, dry and replace. Note: Do not strike unit against hard
surface to remove debris. Damage may result.

5. Store in a clean, dry place.

Maintenance Schedule

Maintenance item Daily Once a week

Clean and inspect tank.
Check power cords.
Clean with all-purpose cleaner and cloth.
Clean Lint Hog™ lter
Flush with Mytee
normal chemical build-up.
Clean with compressed air.
Clean pump-out & vacuum stack lters
Inspect for water leaks and loose hardware.

®

System Maintainer to dissolve

x
x
x
x

x

x
x
x

Trouble Shooting

There is no power.

1. Make sure the machine is plugged into the proper outlet.

2. Check the circuit breaker and reset. Other items should not run on the same circuit
as the machine. The outlet circuit must be a minimum of 20-amps.

3. Check switch. If it is damaged, replace with OEM part.

4. Replace or repair loose wires.

5. Replace motor if damaged.

Pump-out does not work properly.

1. If lters are clogged, remove and rinse with clean water.

2. Check pump-out wiring. It may need to be reconnected.

3. Check pump-out switch, it may need to be replaced with OEM part.

Vacuum motor does not work properly.

1. Check to see that all vacuum hoses are tightly connected.

2. Check vacuum port caps in back to make sure they are tightened.

3. Insure vacuum lid is tightened.

4. Check that the electronic shut-off switch is in the operating position.

5. If electronic shut-off switch is activated (pointing 45º), empty tank of all water.

6. Check to see if rear plugs are tight and secure.

Water is leaking.

1. Make sure unit is unplugged before servicing.

2. If foam is coming out of the recovery tank, use a low foaming detergent and/or
defoaming agent.

3. Check to make sure debris has not been sucked through vacuum stack into the
motor. Pre-vacuuming prevents this situation.

4. If a vacuum hose is leaking, make sure Cuff-Lynx™ and Lint Hog™are securely
tightened.

5. Check hose ttings.

6. Insure all brass ttings are tightened.

FAQs

Q – What does the Air Hog™ Plus weigh and what are the dimensions?
A – Weight is 79 lbs. and dimensions are 32.5” x 17.5” x 30.5”.

Q – What comes standard with the Air Hog™ Plus?
A – Lint Hog™ debris lter, internal stainless steel lter, built-in Cuff-Lynx™ hose
connections, 25’ power cord, roto-molded polyethylene body, 6” non-marking
wheels, 2” non-marking casters. Also includes the following additional Cuff-Lynx™
hose connections:

· Part No. H136 – 2” male swivel coupler, connects to 2” female vacuum hose.

· Part No. H141 – 2” female reducer, connects to 1 ½” female vacuum hose.

· Part No. H110 – 2” female swivel coupler, connects to 2” female vacuum hose.

Q – Where do I plug in the machine?
A – Two separate 20-amp grounded curcuits are required.

Q – What machines are recommended for use with the Air Hog™ Plus?
A – The Air Hog™ Plus can be used to boost the CFM of any extractor with a single
3-stage or higher vacuum motor, including Mytee’s
Special™, Speedster
washer for increased water lift.

®

, and Breeze™ models. Can also be used with a pressure

®

M-Series™, HP, Contractor’s

Warranty

Mytee Limited Warranty Policy
Mytee Products, Inc. endeavors to provide high quality products and product support
to its customers and therefore backs up all of its new products purchased from Mytee
Products Inc. (Mytee) or any authorized Mytee distributor/service center with this
limited warranty.

This limited warranty begins on the date of the customer purchase and is valid and
available to the original purchaser only. Mytee products are for commercial use only
and are not intended for personal, family or household uses.

HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY,
EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGE­MENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY.
THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF MYTEES GOODS. THIS LIM­ITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT
ANY TIME WITHOUT NOTICE.

90-DAY PARTS AND LABOR LIMITED WARRANTY: Mytee will cover parts and labor
on all components for 90 days from the date of original purchase. This warranty cov­ers the cost of replacement and labor only, and does not cover shipping costs.

WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for
90 days from the date of original purchase. Wear parts are items which wear out as a
result of usage or the passage of time and are consumed despite attempts to main­tain them, such as gaskets, wheels, brass, cords, wires, electrical terminals, hoses,
switches, thermostats, plastisol parts, lters, bearings, brushes, solenoids, O-rings,
bulbs, heating elements, castors, or other parts deemed wear items in Mytees sole
discretion. This warranty covers the cost of replacement only and does not cover
shipping or labor costs.

1-YEAR MAJOR COMPONENTS WARRANTY: Mytee warrants that pumps, vacuum
and oor machine motors, and heaters are covered for a one (1) year limited war­ranty from the date of original purchase. This warranty does not apply and is void if
the pump, vacuum motor, or heater has worn brush motors, water damage, chemical
build-up, chemical damage, or evidence of abuse, neglect or tampering. This warran­ty covers the cost of replacement only, and does not cover shipping or labor costs.

HOUSING LIFETIME LIMITED WARRANTY: Mytee warrants that all rotationally
molded housing and tanks will be free from manufacturing defects, defects in work­manship, and defects in material for the life of the part. Replacement cost does not
include the cost of shipping or labor.

LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR
OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER
ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO
EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.

All limited warranties are void for, and Mytee does not warrant in any way, any prod­uct that evidences misapplication, improper installation, abuse, lack of maintenance,
negligence in use or care, abnormal use, alteration of design, use of incompatible
or corrosive chemicals, use in a rental service, and/or servicing, installation of parts,
or repairs by anyone other than Mytee or a Mytee authorized distributor or service
center. Mytee may make changes in products it manufactures and markets at any
time; these changes are made without obligation to change, retrot, or upgrade any
product previously sold or manufactured.
Mytee has no obligation to honor the limited warranties set forth herein unless the
original purchaser, promptly upon discovering the warranty claim and prior to continu­ing to use the product, contacts Mytee or a Mytee authorized distributor or service
center to describe the claim and to receive and follow instructions for documenting
and resolving the claim. In addition, the purchaser must provide the product to which
the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection.

10

If any provision or portion of this limited warranty policy is found to be unenforceable,
then the remaining provisions and portions shall remain valid and enforceable. If
any provision or portion of this limited warranty policy is found to be limited by law,
then that provision or portion shall be construed to make it effective within the bounds
of law. For example, if there are legal limitations on the duration of warranties, the
warranties made herein shall be construed to have the minimum duration required
by law, or, if there are legal limitations of exclusion of remedies, the exclusions
made herein shall be construed to apply to the fullest extent possible without
violating the law.

The validity, construction and performance of this warranty policy shall be governed
by the laws of the State of California, without respect to conicts of laws principles.
The exclusive jurisdiction of any legal action arising from or related to this warranty
policy shall be in the State of California and no legal action shall be commenced
elsewhere.

Return Material Authorization Procedure

It is the responsibility of any Authorized Service Center (ASC) or distributor with
written authorization to ensure the customer’s equipment is repaired as soon as
possible. Only Mytee Products Inc. or it’s authorized dealers with written authoriza­tion, service centers, and agents may make warranty repairs on these products. All
others do so at their own risk and expense.

The Distributor must follow Mytee Products, Inc. standard RMA procedure:

1. When a repair falls within the warranty time period for a piece of equipment, the
distributor will ll out a RMA/warranty claim form. This form will act as a repair order
to replace any defective parts.

2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim
form for evaluation at the customer’s expense. This shipping is non-refundable. All
warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if
warranty will be approved. Any credit for repair and/or parts will only be issued upon
evaluation and approval from Mytee Products, Inc.

3. When warranty is approved, the distributor’s account will be credited for the
replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s)
to the distributor prepaid. If warranty is denied the distributor’s account will not be
credited for any parts sent for this claim.

GENERAL INFORMATION

11

7300-SLA AIR HOG™ PLUS PARTS & PRICING

F

1

2

E

D

C

B

A

PRODUCTS, INC.

858-679-1191

Booster, TM

mytee

TITLE:

DATE

2/2014

NAME

M.LaBarbera

PROPRIETARY AND CONFIDENTIAL

COMMENTS:

CHECKED

DRAWN

REV

OD

SHEET 1 OF 3

1

DO NOT

SCALE DRAWING

7300-SLA

DWG. NO.

C

SCALE: 1:32

SIZE

2

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS

PROHIBITED.

MSRP

$3.99 ea

QTY.

1

$9.99 ea

1

3

4

DESCRIPTION

QD, 1/2" npt x 3/4" mgh, pump-out

qd, 3/4" female x female garden hose

5

6

PART NO.

NO.

ITEM

MSRP

QTY.

B204

B205B

53

54

$3.99 ea

$23.99 ea

1

1

$4.99 ea

13.99 ea

$10.00 ea

1

1

$9.99 ea

$13.99 ea

1

1

$11.49 ea

1

latch, front

nut, lock, 2", steel

plug, brass, 3/4", garden hose 1

coupler, 2" dia x 2.5" length, s/s

B221

H194

55

56

$6.99 ea

$36.99 ea

1

1

light, indicator, 125v (amber)

power cord, pigtail, 30", 12/3, black

E550

H020

H486

E512B

57

58

59

60

$0.99 ea

4

$1.99 ea

$34.99 ea

2

1

$6.99 ea

3

$3.19 ea

$1.99 ea

$1.99 ea

$62.99 ea

1

1

1 $164.99 ea

1

base, tm booster

nut, lock, 1/2" steel

tting, strain relief, cord

H220

H221

61

62

$4.99 ea

$15.99 ea

1

1

controller, circuit light

bumper, 7/8" x 1/4" head 1

E564

P571

G068

65

63

64

$0.99 ea

$2.99 ea

$8.99 ea

1

1

$2.99 ea

$6.99 ea

$0.99 ea

$13.99 ea

4 $0.99

1

3

switch, rocker, 2 position

plate, switch,8070, hp60, 7300

screw, 10-32 x 1/2" SHCS, alloy 1

screw, 10-32 x 3/4, phil at full thread

H636

67

$1.99 ft

1

E515

H389

68

69

$7.99 ea

$3.99 ea

1

1

H186

66

$2.00 ea

1

$0.99 ea

$21.49 ea

$94.99 ea

1

1

3

12

fan, cooling, 115V

guard, cooling fan, wire

screw, 10 x 5/8" hex head, zinc

controller, water level, dual pump or vac

E370

H343

H296

C317

72

71

$0.99 ea

$0.99 ea

2

18

73

$0.99 ea

$0.99 ea

2

14

70

$0.99 ea

$9.99 ea

1

$0.99 ea

$28.99 ea

2

2

$14.99 ea

1

$14.99 ea

2

wheel, 8"

axle, 15.60" x .50" dia

c-clip, 12mm, external

H239

H227

76

77

$0.99 ea

$1.99 ea

4

1

H042

78

$14.49 ea

1

plate, dual manifold, 9" x 13"

H253

79

$6.99 ea

1

bolt, 1/4-20 x 1" hex head, s/s 8

caster, 3", Black Hub, Gray Tread

H342

H667

74

75

$2.49 ea

$12.99 ea

1

1

$8.99 ft

3

$4.99 ea

6

2 $139.99 ea

$10.99 ea

1

$1.49 ea

$12.49 ea

5

1

$0.99 ea

$14.99 ea

6

2

inlet, 2"

clamp, hose, 2-1/4 dia

vac support, 3 stage, 4-1/16"

vac motor, 3 stage, low amp

vac hose, 2", black, wire reinforced

P685

H501

C302LA

PH628-11

83

81

82

80

$7.99/ft

$8.99 ea

$4.99 ea

$2.99 ea

1

1

1

bolt, 1/4x20x3/4" hex head

manifold, single vac, no gasket

cu hose, 2 X 2, wire reinforced

H544

85

$0.99 ea

$3.99 ea

2

1

P735

H202

87

86

$3.99 ea

3

1 $215.00 ea

H217

84

$3.99 ea

$0.99 ea

2

14

$0.99 ea

4

MSRP

$3.99 ea

$4.99 ea

$6.29 pak

1

1

QTY.

DESCRIPTION

1

piglet lter

Cu-Lynx, 2" to 1.5" reducer

lter bag, 3.5" metal O-ring, mesh bag

H141

G008

$11.99 ea

$36.99 ea

1

1

G076

$0.99 ea

6

PART NO.

ITEMS NOT SHOWN

$1.99 ea

$6.99 ea

4

2

n/a

$3.99 ea

1

Cu-Lynx, 2" hose x 2" fem swivel Cu-Lynx

H110

$8.99 ft

1

n/a

$3.99 ea

$74.99 ea

1

1

1

1

manual, tm vacuum booster

stop sign, register your product

power cord, ext, 50', 12/3 black

Cu-Lynx, 2" hose x 2" male swivel Cu-Lynx

E530

H136

AD127

ADM-7300

$8.99 ft

$0.99 ea

$9.49 ea

$0.99 ea

1 $187.49 ea

14

$0.99 ea

4

1

$6.99 ea

$14.99 ea

4

1

1

1

3

4

5

6

7

DESCRIPTION

pipe, pvc, 1/2" x 20'

upper bracket, tm booster

elbow, pvc 1/2" fmt x 1/2" fms

level switch, vacuum shut-o, rear threads

E373

P680

H082

P677-5

12

13

14

15

E

Cu-Lynx, 2" m cu x 2" mpt

8

H135

PART NO.

1

NO.

ITEM

body, lint hog, new style

gasket, 3.25" i.d. x 5.88" o.d.

cap, 6", threaded, w/ 2" npt

P561

G031

3

2

lower bracket, tm booster

basket, strainer, 4.5 DIA x 12.5

screw, 10-32 x 1" phil pan head, s/s

H359

H231

H081

P563A

4

5

6

7

F

elbow, inlet assembly 2"

adapter, pvc, 2" fslip x 2" mpt

gasket, vac motor - Mytee Lite

screw, 10-32 x 1/2" phil pan head, s/s 13

P567

H230

A926

G004-A

8

9

10

11

washer, 1/4" at, s/s

washer, 1/4" lock, s/s

adapter, pvc, 1/2" fpt x s

adapter, pvc, 1/2" fslp x 1/2" mpt

P572

P679

H210

16

17

18

mesh lter, auto dump, 1/2" npt

nut, lock, 1/4-20, nylon insert, s/s

bolt, 1/4-20 x 1/2", hex head, zinc

H213

H201

H216

H333

19

20

21

22

D

pipe, pvc, 2" 1

nipple, brass, 3/8" x close

washer, 11/16"id x 1-1/2"od x .075, s/s

bushing, brass, 1/2"mpt x 3/8" fpt, hex

B210

23

elbow, brass, 90 deg, 1/2" barb x 3/8" fpt

B216

B236

H299

24

25

26

elbow, 45 deg, 2" pvc

adaptor, pvc 2, fmsl x fmt

P684

27

screen, mesh lter, 2-3/8" dia

P683

G021

P682-9

28

29

30

C

12

cu-lynx, 2" plug

bracket, front, small

tank, truckmount booster

bolt, 1/4x1-1/2", hex head zinc

Cu-Lynx, 2" mpt x 2" female cu

P537

H316

H379

H124

G022 lter, foam, 2-3/8" x 1"

31

32

H121

33

34

35

36

gasket, 7", vac lid

handle, breeze and dx

washer, 1/4"id x 1"od, at, s/s

washer, buna 1-1/8" od x 3/16" id

pump out, 115v

lid, vac tank, clear, 7"

screw, #8 x 5/8 phil oval, s/s

nut, kep, #10-32 zinc

sol hose, 1/2", 3045psi, black

bolt, 1/4-20 x 3/4" serrated hex ange, zinc

H768

H211

H485

G052

37

38

39

B

H304

G091

G090

40

41

42

43

C381

PH615-25

45

44

H273

46

Part prices are subject to change.Order parts at: www.mytee.com/products/7300-s-air-hog-plus-vacuum-booster

7

ferrule, 1/2", brass

sol hose, 1/2", 3045psi, black

coupling, 3/4" fpt x 1/2" fpt

bushing, hex, 3/8" mpt x 1/2" fpt

adapter, brass, 1/2" barb x 1/2" mpt

screw, 10-32 x 1-1/4", phil at full thread, black oxide

H185

47

B173

PH615-8

49

48

A

B132

50

B270

51

8

B271

52

7300-SLA AIR HOG™ PLUS PARTS & PRICING

F

1

E

D

C

B

A

PRODUCTS, INC.

858-679-1191

Booster, TM

mytee

TITLE:

DATE

2/2014

REV

OD

SHEET 2 OF 3

1

DO NOT

SCALE DRAWING

7300-SLA

DWG. NO.

C

SCALE: 1:32

SIZE

2

80

80

84

85

87

86

83

3

82

80

21

37

81

8

79

67

46

66

65

63

62

37

61

60

59

11

68

46

64

58

11

66

70

51

72

71

46

44

75

to lter

21

26

thru B236

73

18

"OUT"

to pump-out

74

thu B132

50

76

77

78

69

NAME

M.LaBarbera

CHECKED

DRAWN

PROPRIETARY AND CONFIDENTIAL

COMMENTS:

2

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS

PROHIBITED.

3

52

53

24

4

35

54

55

56

57

50

18

48

49

51

B270

hose thru

to garden

5

43

45

46

14

16

17

15

4

13

47

19

20

18

24

25

26

24

23

22

21

18

33

32

29

30

31

27

28

5

42

6

41

40

37

38

39

35

34

1

2

36

44

"IN"

to pump-out

thru PH615-25

6

3

7

8

F

E

4

12

11

8

9

6

5

7

7

10

8

D

C

B

A

13

7300-SLA AIR HOG™ PLUS WIRING DIAGRAM

E-515 E-515

C-317

Cooling

Fan

L2

L1

L2

L1

Out

Pump

C-381

VAC 2

C-302LA

4/11/2014

G

Ground to

G

Metal Plate

7300-SLA

115 Volt System

L1

E-515

G

L2

#E-370

relays

Float

Switch

115V

L2

L1

VAC 1

C-302LA

G

14

NOTES

15

NOTES

Mytee Products Inc.

13655 Stowe Dr.

Poway, Ca. 92 06 4

www.my te e. co m

© 2014 Mytee Products Inc.

Printed in the U.S.A.

16