Page 1
Installation Guide
Product Code: MYWEO350
PRODUCT #:
MYWEO350
FEATURES:
This practical combined towel warmer and radiator wall mount design. Heat output of 200 watts. Backlit on/off switch and
matching installation accessories provided. Standard finish is polished chrome. Upgrade finishes available in Gold,
Nickel, Satin Nickel, Regal Brass, Satin Brass, Satin Gold, or Baked epoxy powder coat white finish.
ITEM:
Classic Wall Mount Towel Warmer from
Myson
Myson
SOURCE FOR PURCHASE:
SpaEquip Inc.
211 Wappo Ave
Calistoga, CA 94515
(707) 737-1100
www.spaequip.com
SPECIFICATIONS:
Dimensions: 25.25"L x 4.5"W x 33.5"H
Electrical: 120V AC, 200 Watts
Suggested Outlet: GFCI Hard wired
Plumbing: None
Notes: Mount with top 5-1/2' AFF if used to warm robes
Warranty: 5 Years
Certifications: UL
Country of Origin: Turkey
Installed By: Client's Contractor
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 1 of 11
Page 2
DIM (B)
DIM (A)
WEO100
WEO165
WEO Technical Sheet
4" (100mm)
Product Code: MYWEO350
Tamar WEO
Classic
Electric
A
WEO350
B
DIM (B)
DIM (C)
WEO140
DIM (C)
DIM (A)
DIM (F)
DIM (D)
DIM (F)
DIM (D)
+ +
+ +
DIM (E)
MYSON
DIM (F)
DIM (C)
DIM (D)
+ +
MYSON
Models
WEO100 WEO140 WEO165 WEO350
Loading
DIM-A
DIM-B
DIM-C
MYSON
DIM-D
DIM-E
DIM-F 10-3/4 ins 10-3/4 ins 11-3/4 ins 11-3/4 ins
100 watts 140 watts 165 watts 200 watts
120 volts 120 volts 120 volts 120 volts
23 ins 23 ins 33 ins 25 ins
586 mm 586 mm 838 mm 636 mm
24-1/4 ins 33-1/2 ins 33-1/2 ins 33-1/2 ins
616 mm 851 mm 851 mm 851 mm
9 ins 9 ins 10 ins 10 ins
229 mm 229 mm 254 mm 254 mm
12 ins 12 ins 13 ins 13 ins
305 mm 305 mm 330 mm 330 mm
13-7/8 ins 23-1/8ins 20-1/4 ins 25-1/4 ins
352 mm 587 mm 514 mm 641 mm
2-1/4"
55mm
Fixing Flange
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 2 of 11
Myson, Inc., 948 Hercules Drive, Suite 5 Colchester, VT 05446 1-800-698-9690 www.mysoninc.com
Page 3
Product Code: MYWEO350
ELECTRIC TOWEL WARMERS
INSTALLATION & OPERATING INSTRUCTIONS
CAUTION:
1. Read this entire instruction manual thoroughly before 6. This unit is not intended for use in a shower.
beginning installation and save these instructions.
2. BE CERTAIN ELECTRICITY IS SHUT OFF AT THE MAIN 7. To avoid a possible fire hazard, the Towel Warmer
PANEL BEFORE WIRING or servicing your Towel Warmer. Tube that has the electric wiring affixed to it must
remain in its intended position. DO NOT MOUNT
3. Your Myson Towel Warmer must be properly grounded. All THE UNIT HORIZONTALLY OR UPSIDE
wiring must be in accordance with the National Electric Codes DOWN!
and local codes and carried out by a licensed electrician. NOTE: Sticker denotes TOP of unit.
4. Follow instructions accurately to make certain the Towel 8. TO ENSURE FULL EFFICIENCY OF YOUR
Warmer is properly attached to the wall. FAILURE TO TOWEL WARMER, PLEASE FOLLOW ALL
FOLLOW THESE STEPS COULD RESULT IN PROBLEMS. THE INSTRUCTIONS CAREFULLY.
OBSERVING THE “CAUTION” NOTATIONS
5. Do not use an abrasive or chlorine-based cleaner on the FOR EACH STEP.
Towel Warmer. A mild detergent, used with a soft, damp
cloth, will restore most units to their original luster. A soft,
dry cloth may be used to polish. **Please make certain the
unit is cold when it is cleaned.
READ COMPLETELY BEFORE BEGINNING.
GENERAL: The Myson Electric Towel Warmer is permanently oil filled and has been designed to provide an all-year round service
for warming and airing towels and articles of clothing; the larger models will take the chill off a normal sized room.
TOWEL WARMERS ARE HEAVY! WE RECOMMEND THAT TWO PEOPLE INSTALL THE TOWEL WARMER!
MYSON Electric Towel Warmers require 110 VAC. Ground Fault Circuit protection is required by most building codes. Like all
electric fixtures, there may be some restrictions on proximity to water sources; consult your Local Inspector. All electric models are
UL approved with a back lit switch to indicate when the unit is ON. They are oil filled to provide a uniform heat to the full tube area.
While these units are designed for continuous operation, most installations use a timer to control the ON/OFF Cycle.
STEP 1: INSPECT MYSON TOWEL WARMER
(Note: Replacement parts are available for purchase should a part become damaged or lost during installation.)
A. Unpack the Myson Towel Warmer carefully to avoid any damage or loss of any part. When opening the box and
unwrapping the Towel Warmer, be sure that the parts that come with the Towel Warmer, (i.e. – brackets, flanges, and
mounting screws), are not accidentally discarded.
B. It is your responsibility to immediately inspect the Towel Warmer for any damage. Shipping damage should be reported
immediately to your place of purchase.
C. Check for enclosed Wire Encasement Kit (fig. 1) on the following Towel Warmer Lines: Classic, Traditional, and the
ERR, ECM & EMR750 Contemporary Electric.
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 3 of 11
Page 4
Product Code: MYWEO350
*Please note that the ERR & ECM models come with the Wire Encasement Kit box down, (at bottom of right
vertical rail), whereas the EMR750, Classic, and Traditional lines come with the Wire Encasement Kit as shown
in fig. 1, (box on right).
(ECAVH & ERHAH), and the EECOSH, ECMH3, EGAVH, and EINTH Multirails.
fig. 2: Discreet Wire Kit
IT IS YOUR RESPONSIBILITY TO IMMEDIATELY INSPECT FOR ANY DAMAGE.
SHIPPING DAMAGE SHOULD BE REPORTED IMMEDIATELY TO YOUR PLACE OF PURCHASE.
STEP 2: INSTALLATION
(For The Lines That Come With The Wire Encasement Kit Shown in fig. 1: Classic, Premier, Master Suite, Multirail models ERR
& ECM, and Space Saver.)
¨CAUTION: DO NOT TURN THE SWITCH BOX! DOING SO WILL CAUSE THE OIL SEAL TO BREAK!
Check for attached Discreet Wire Kit (fig. 2) on the following Towel Warmer Lines: Electric Inspirational Designs,
A. Mount Wire Encasement Kit to the back of the switch box with the provided screws, slipping wiring through the
tube that returns to the wall.
B. Most MYSON Classic, Premier, Master Suite, and Space Saver Towel Warmers have been designed with
integral wall flanges. These will facilitate a permanent and secure mounting of the Towel Warmer to the wall. Make
certain there is ample clearance on both sides of the Towel Warmer. The unit is supplied with the proper hardware
for installation. Be sure wall construction is appropriate for hanging. BACKING IS RECOMMENDED!
1. Locate the model of the Towel Warmer being installed on the following page. Rough-in dimensions for a
2” x 4” standard electrical box are given for each model. Rough-in the box per dimensions given,
providing 110 VAC on a dedicated 15 amp circuit to the box.
2. Align the Towel Warmer with the electric box; mount the top of the Towel Warmer loosely using the
screws provided.
3. Follow the electrical connections per directions in Step 3 below.
4. The MYSON Towel Warmer should be fixed to the wall using the screws provided.
*PLEASE SEE PAGE 6 FOR MOUNTING INSTRUCTIONS FOR THE FOLLOWING MODELS: ERR, ECM, EMR,
EINTH & ECMH
**PLEASE SEE PAGE 7 FOR MOUNTING INSTRUCTIONS FOR THE FOLLOWING MODELS: ERHAH & EGAVH
***PLEASE SEE PAGE 8 FOR MOUNTING INSTRUCTIONS FOR THE FOLLOWING MODEL: EECOSH
(For The Lines That Come With The Discreet Wire Kit Shown in fig. 2: Electric Inspirational Designs (ECAVH & ERHAH), and
the EECOSH, ECMH3, EGAVH & EINTH Multirails.)
1. Prior to hanging and connecting the Towel Warmer, the 110 VAC on the dedicated 15 amp circuit, must
be roughed-in to a standard sized outlet box in the wall. The wire box should be positioned at the lower
right corner of the Towel Warmer.
2. At this point, the mounting hardware should be located and fixed to the wall.
3. The Discreet Wire Kit will be turned to the inside when you receive the product. Loosen the two set
screws and rotate the tube to a position 90 degrees to the wall. Re-tighten the set screws.
¨CAUTION: FAILURE TO LOOSEN THE SCREWS BEFORE ROTATING THE TUBE WILL BREAK THE OIL SEAL!
4. Put the wires through the Wall Plate and fix the Wall Plate to the tube by tightening the large nut supplied
with the kit.
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 4 of 11
Page 5
Product Code: MYWEO350
5. Follow the electrical connections per directions in Step 3 below.
STEP 3: ELECTRICAL CONNECTIONS
¨CAUTION: BE CERTAIN THAT ELECTRICITY IS TURNED OFF AT THE MAIN PANEL BEFORE WIRING IS DONE!
All wiring must conform to National and Local Codes which may vary by locale.
GENERAL: The MYSON Towel Warmer requires 110VAC, 60 HZ power supply. Specific amperage is listed with the Towel
Warmer dimensions. IMPORTANT: THIS APPLIANCE MUST BE GROUNDED!
A. Electrical connections should be made as prescribed by the National Electric or Local Codes. The unit should be wired
using 14 AWG or larger copper wire, and protected by a separate 15 amp circuit breaker.
B. Make connections between Towel Warmer and house wiring using approved connectors to comply with National Electrical
Codes. LIVE (black), NEUTRAL (white), and GROUND (green).
See Page 4 for Wire Encasement Kit Installation.
See Page 5 for Discreet Wire Kit Installation.
C. Energize Towel Warmer Circuit. Turn back-lit ON/OFF switch to the ON position to energize the heating element. Please
allow 45 minutes to an hour for the Towel Warmer to come up to full heat, (140°F). *Note: Towel Warmer temperature
may vary with the ambient temperature of the room.
CAUTION: NO BARE WIRE OR WIRE STRANDS SHOULD BE VISIBLE AFTER MAKING CONNECTIONS.
IMPORTANT: THIS APPLIANCE MUST BE GROUNDED!
STEP 4: CONTROL OPTIONS
A. Manual Control: Each unit has a UL approved ON/OFF switch, which is back lit for added safety and convenience
B. Automatic Control: A UL approved automatic or manual timer or thermostat may be used. Consult the manufacturer of
these items for proper installation and connection to the Towel Warmer.
NOTE: All switches and control devices must be installed on the LOAD (black) side of the Towel Warmer circuit in compliance with
the National Electrical Codes and Local Codes.
STEP 5: OPERATION & MAINTENANCE
Your electric MYSON Towel Warmer can safely and economically be left ON continuously without any detrimental effect either to
the Towel Warmer or the articles on it.
However, when the Towel Warmer is ON, no more than two layers of towels or other similar fabrics should be draped over each rail.
Although hot to the touch, the MYSON Towel Warmer is not hot enough to scorch or burn towels or other similar fabrics.
IMPORTANT: This appliance is intended for towels and similar fabrics that are washed in water. Fabrics that contain soap, laundry
detergents, liquid fabric softeners or after bath oils residue may show what appear to be scorch marks. THIS IS SIMPLY THE
DISCOLORATION OF THE RESIDUE. As stated, the Towel Warmer does not reach sufficient temperature to scorch fabrics.
Myson, INC. is not responsible for fabric discoloration due to laundry detergents, liquid fabric softeners, soap, or after bath oils.
REMINDER ON CLEANING YOUR MYSON TOWEL WARMER
Do not use an abrasive or chlorine-based cleaner on the Towel Warmer.
A mild detergent, used with a soft, damp cloth, will restore most units to their original luster.
A soft, dry cloth may be used to polish the Towel Warmer.
Please make certain the unit is cold when it is cleaned.
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 5 of 11
Page 6
Product Code: MYWEO350
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 6 of 11
Page 7
Product Code: MYWEO350
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 7 of 11
Page 8
Product Code: MYWEO350
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 8 of 11
Page 9
Product Code: MYWEO350
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 9 of 11
Page 10
Product Code: MYWEO350
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 10 of 11
Page 11
Classic Electric Towel Warmers
Product Code: MYWEO350
Model Watts
Lekoro
ES40/1
Lekoro
ES40/2
Tamar
WEO100
Tamar
WEO140
Tamar
WEO165
Tamar
WEO350
Taw ES6/1 165
Taw ES6/2 165
Witham
ES11/1
Witham
ES11/2
Spey ES14/1 100 0.76 27" 27" 6 1/2" 1"
Spey ES14/2 100 0.76 27" 33" 6 1/2" 1"
Tamar
SEO70
100
140
100
140
165
200
165
165
70
Amps
0.76
1.10
0.76
1.10
1.26
1.75
1.26
1.26
1.26
1.26
0.63
Overall
Height (In)
6 3/4" 18 1/4" 12" 1 - 1/4"
6 3/4" 24 1/4" 12" 1 - 1/4"
24 1/4” 23” 4" 1"
33 1/2” 23” 4" 1"
33 1/2” 33” 4" 1"
33 1/2” 25 1/4” 4 1/2" 1"
36 5/8" 27 1/4"
36 5/8" 33 1/4"
27 1/4" 27 1/4" 6 1/2" 1 - 1/4"
33 1/4" 33 1/4" 6 1/2" 1 - 1/4"
19 7/8" 22 7/8” 3 1/2" 1"
Overall
Width (In)
Overall
Projection (In)
Depends on
Wall stays
Depends on
Wall stays
Tube Diameter
(In)
1 - 1/4"
1 - 1/4"
www.spaequip.com P: 707-737-1100 F: 707-737-1150 Page 11 of 11
Loading...