Myson SELECT, T6, DECOR, COLUMN, BENCH Technical Manual

01.11.2011

MYSON

heatingthroughinnovation.

Column Radiator Series

Installation & Technical Guide

02

COLUMN.

MYSON COLUMN radiator's aesthetically sophisticated design was conceived for
technologically superior heating. Their design form makes them suitable for a wide range

of architectural applications from retro to modern.

Contents/Warranty

03
04

05

06
07
08

12

Myson, Inc. Limited Warranty

Myson, Inc warrants the following products against defects in material and workmanship to the original owner for the
duration listed from date of installation or three months after date of shipment, whichever comes first.

The remedy in all cases shall be to repair or replace the product at Myson’s discretion upon verification of a factory defect. If
replacement is required, and an exact replacement product is no longer available, Myson reserves the right to furnish a
similar product of equal value.

NO REMOVAL, SHIPPING OR INSTALLATION EXPENSES ARE REIMBURSIBLE

The original purchaser is responsible for determining the suitability of the Myson product for their installation. Installation
and troubleshooting should be performed by a competent technician with knowledge of hydronic heating and/or basic
electricity.

Damages occurring during shipment, transit, storage or handling, abuse, neglect, accident, misapplication, incorrect power
line voltage, mproper water source or connection, fire, flood or other Acts of God are not covered. Freight damage claims

MUST be made within 10 days of receipt from Myson. No Exceptions.

STEEL PANEL RADIATORS -- SELECT, T6, DÉCOR, COLUMN AND BENCH

The duration of warranty for steel panel radiators is 5 Years.

•

Painted finishes will not peel or flake from the surface of the radiator

•

The body of the radiator and its welded joints will not leak when the product is properly installed and maintained
according to Myson's instructions.

What is not covered:

•

Rust occurring from improperly sealed threaded connections or oxygen corrosion

•

Electrolytic corrosion caused by failure to flush the system properly after initial installation

Contents

What is covered:

Important information
Product description
Model overview / connection dimensions

Piping & rough-in

Wall bracket position information
Optional Floor bracket information

Heating outputs / weights / water content

Piping arrangements
Valve selection

Heat output factors / System start - up

13

9 - 10

11

Important Information 03

BEFORE YOU BEGIN

SAFETY PRECAUTIONS

Rad

iators are hot when in use, and as such, present a

risk of burns

to

users

on

prolonged

contact.

The

temperature

of

a

radiator

is

dependent

on

the

temperature

of

the

system

water,

as

set

by

the

system installer or user. Installers and users
should ensure that those who may come into close proximity to hot radiators are aware of the risk of burns. Installers
and users should take all necessary steps to minimise the risks of burns. If the risk is significant, consideration should be
given to installing low surface temperature radiators, or to placing guards in front of the radiators.

For the correct installation of radiators it is essential that the fixing of the radiator is carried out in such a way
that it is suitable for intended use AND predictable misuse. A number of elements

need to be taken into
consideration including the fixing method used to secure the radiator to the wall, the type and condition of the wall
itself, and any additional potential forces or weights that may happen to be applied to the radiator, prior to
finalising installation. IN ALL CASES IT IS STRONGLY RECOMMENDED THAT A SUITABLY QUALIFIED

PROFESSIONAL INSTALLER OR SIMILAR TRADESPERSON CARRIES OUT THE INSTALLATION.

INTRODUCTION

The Myson Column Radiator will keep any room in comfort and style. We at Myson Inc. thank you for your purchase of the
Column Radiator. Each radiator combines Myson’s compact design and advanced steel construction with a durable baked
epoxy/polyester enamel powder coat finish. Myson’s sleek styling and thorough testing provides attractiveness and
dependability. Myson’s goal is to assure the highest performance, quality, reliability and outstanding customer service.

CAUTION

Step 1 Read this entire instruction manual thoroughly before beginning installation.
Step 2 To ensure full efficiency of your Myson Décor Steel Panel Radiator, please follow all

the instructions carefully .

Step 3 Failure to follow these instructions will invalidate the manufacturer’s warranty.

APPLICATION

Myson radiators are only for use in recirculating closed loop hydronic-heating systems. These radiators are not recom­mended for gravity systems. DO NOT USE STEAM IN THESE RADIATORS.

INSPECT FOR DAMAGE
NOTE: Inspect materials for concealed shipping damage. You only have 10 days to file a freight claim. If items are

damaged or missing, please call Myson at 1-800-698-9690.

INSPECTION FOR COMPLETENESS

Unpack the radiator carefully to avoid damage or loss of parts. The Column Radiator will come with the following parts:

• Wall mounting bracket kit

• Plastic inserts for noise suppression

• Stainless steel solid plug

• Vent plug

IT IS STRONGLY RECOMMENDED THAT A SUITABLY QUALIFIED PROFESSIONAL
INSTALLER OR SIMILAR TRADESPERSON CARRIES OUT THE INSTALLATION.

Myson products are designed to be installed by professional tradespeople. Myson instructions are meant to be thorough;
however it is assumed that the installer has the appropriate technical knowledge related to building codes, standard trade
practices, and proper use of the tools of the trade. Should a homeowner without such knowledge or skill take it upon him/
herself to attempt the installation, Myson will not be responsible for any damages, injuries or unsatisfactory performance of the
Myson product used.

DESIGN AND LAYOUT CONDITIONS

Myson Column Radiators should only be used with a properly sized recirculation pump closed loop hydronic heating system.
Please consult national and local codes for specific restrictions that may be imposed on your installation. Position your radiator
away from your circulator pump to avoid either excess pressure that could force water out the air vent or excess suction that
could draw air into the system. The preferred positioning for the Column radiator is below a window where it can minimize
downdrafts from glazed areas.

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

Radiators

2 - COLUMN:

Standard Heights: 18, 24, & 79 inches (45, 60, & 200 cm)

Coatings:

1. Undercoat: electrophoretic, using water-soluble paints,
conforming to

DIN 55900 part 1, stoved at 329

° F;

2. Finish: electrostatic powder coating, conforming to DIN 55900 part 2,
i

n a state-of-t

he-art facility. (On request, and at a supplementary charge,
a range of RAL and sanitary ware colours can be offered.) This
particularly

r

obust coating is stoved at an object temperature of

356° F

.

Packaging: 1. Cardboard packaging

2. Edge protection

3. Shrink foil

COLUMN product description

Quality certificates

MYSON offers its customers strong
brands that meet highest quality
standards. All the production sites’
production processes are certified ac­cording to ISO. The quality and perfor­mance specifications of the convectors
and heating panels have been verifi ed
by recognised European institutions.

The standards that the quality certifi ­cates require us to maintain give you
security, the best heating performance
and premium product quality. For the
MYSON warranty conditions, please
refer to the table of contents page of
this manual.

Strong brands of the highest quality

Connections:
4 x internal thread G 1/2“ BSP,
welded-in for supply and return.
Vent and drain plugs (or dummy
plug) are included

Maximum positive
operating pressure:

145 psi

Maximum operating
temperature:

max.

72psi

max.

04

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

PRODUCT DESCRIPTION

12 - 3045

Overall Height [cm]

Number of Columns

Number of Sections



Additional sizes and models are available as special order

Tested to positive
pressure:

188.5 psi

248° F

5

5

5

Manufacture

MYSON COLUMN radiators are
manufactured using a unique

laser

welding proce

ss that virtually eliminates

the visible

welding

points

associated

with

the

traditional

methods

of

manufacturing

this

type

of

radiator.

The

clean

finish

significantly

enhances the

aesthetic qualities of the radiator.

Tube Details

Precision, D-

profile steel

tube is used

for

all

outside

surfaces

which

ensures

high

outputs

and

soft,

rounded

edges

for

maximum

safety.

All

MYSON

COLUMN radiators are

manufactured and tested to EN 442.

Paint Finish

Every MYSON COLUMN radiator
undergoes a multi-stage pre-treatment
process followed by an epoxy polyester
primer coating. A stoved

epoxy

polyester powder coat in white (RAL

9016) is applied to all front and rear
surfaces

allowing the MYSON
COLUMN to be fitted without further
painting.

MYSON COLUMN radiators carry a 5 year
guarantee against defects caused by
faulty materials or manufacture.

3 - COLUMN:

Standard Heights: 12, 18, & 24 inches (30, 45, & 60 cm)

4 - COLUMN:

Standard Height: 24

inches

(60 cm)



See pages 9 & 10 for standard number of sections and outputs

ABOVE EXAMPLE:
12 Sections, 3 Column, 18"High

COLUM

N model overview / connection dimensions

Dimension and Mounting Quick Reference

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

05

Length equals the number of
sections times 2"
Example:

56 sections times 2"

equals 112"

2"

1"

1 1/4"

1 1/4"

All tappings are 1/2" BSPT

C

L

LKD16AN

C

L

1 3/4"

1 3/4"

Shown with DAV12 and
LKD16AN valves. See page 12
for additional valve choices .

DAV12

4"

3/4"

1-3/16"

2-5/16"

3-1/4"

5/8"

2"

1/2"

Position 2

Position 1

Column Radiator Wall Brackets

4 Column

5 1/2"

3 Column

4"

2 Column

2 1/2"

Pipe centers from finished wall are
dependent on which mounting slot is
selected on the mounting bracket and
the number of columns.

2 Column 3 Column 4 Column

Position 1 Min: 21/2"

31/4"

4"

Position 2 Max:

27/8"

35/8"

43/8"

To obtain pipe centers using Myson
valves multuply the number of
sections by 2" and add 3.5".
Example: A 12 section radiator would
be 12 x 2"+ 3.5" = 27.5"

MYSON COLUMN RADIATOR
ROUGH -IN SPECIFICATIONS

COLUMN piping & rough-in

H and V models

Suitable for mono-flo, home run or 2-pipe systems

Rough-in dimension shown at right is for a TRV and a
LKD valve or a pair of LKD valves.
When using FF valves add 3-5/8" to overall length.

Recommendation:
Radiator tappings and valve spuds are 1/2"BSP.
Professional expertise is required when sealing these
"straight" threads. Failure to properly seal the
connections will result in leaks resulting in property
damage.

NOTE ! Myson is not responsible for damage resulting from improper workmanship.

NOTE ! Rough-in information is given for Myson control valves. Valve specifications vary by manufacturer.
Myson will not be responsible for damage or repair of property resulting from the use of non-Myson valves.

06

Overall Length + 3-1/2"

LKD16AN

FF16WAC

TRV

•

All installations require 2 valves per radiator

•

All valves are ½” BSP thread for connection to

the
radiator and ½” NPT thread for connection to the
system (also includes compression nut and ferrule
for connection to ½” copper)

•

Valves are available in 3 basic patterns: angle,
straight, and inverted angle (TRV only)

•

Basic Installation: use 2 – LKD16AN (angle) or
LKD16SN (str

aight) manual valves, nickel plated with

screwdriver stops and caps

•

Basic upgrade: use 1 - FF16WAC and 1 - FF16LAC
manual valves, angle only, chrome plated

with white
handles (FF16WAC is adjustable for balancing,
FF16LAC is fixed open but can be closed for service)

•

TRV (thermostatic radiator valves) are available for
automatic temperature control of individual radiators:
available in 3 body patterns,

with or without
thermostatic head (sensor), use in conjunction with
LKD or FF

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

NOTE: See page 5 or 7 for rough-in from finished
wall to pipe centers.

See page 12 for additional valve information

All MYSON COLUMN radiators
are manufactured with an internal
baffle. The tapping with the
baffle is identified with a RED
plastic cap, all others being
BLUE. It is important that the
supply inlet is connected to

the

tapping identified in RED.

MYSON COLUMN radiators are suitable for the use of
BBOE (Bottom Bottom Opposite

End), TBSE (Top

Bottom Same

End) and TBOE (Top Bottom Opposite
End) connections. TTOE (Top Top Opposite End)
connections cannot be used.

A

ll systems must be designed with

suitable pipe sizing

and

with adequate

pump head. Failure to do this
may lead to trapped air and cold spots because of
insufficient pressure and water flow will not drive the
air from the radiator. The taller and more tubes a
radiator has, the more likely this is to happen.

The installation work must be carried out with
precautions taken to avoid

contamination

which

could

lead

to

corrosion.

If a corrosion

inhibitor

or
other water treatment is to be used, the
Manufacturer’s Instructions must be strictly followed.

The MYSON COLUMN radiator's large diameter
steel tu

be contruction ensures a negligible
pressure drop through the radiator. The pressure
drop through the radiator can be ignored in the
design of most hydronic systems.

2" 13/16"

5

/8"

3

/4"

13

/32"

3

/16"

1

/4"

15

/64"

9

/16"

19

/32"

9

/64"

9

/16"

11

/16"

3

/16"

11

/16"

1

/2"

13

/16"

3

/8"

2

5

/

16

"

3

1

/

4

"

11

/32"

1

/4"

25

/32"

Radiator
Bracket

Angle Wall

Bracket

insert

Ensure tight

fit here

19/32"

27/

16"

7

/16"

A

(see table below)

25

/32"

13/16"

7

/16"

3

/4"

1"

1

/2"

15

/32"

Wall &

Bracket

Wall &

Radiator

A = Distance between Wall & Center

Wall Bracket &

Radiator Bracket

25/32"

7

/16"

17/32" 2 1/2" 3 1/4"

4"

13/16"

7

/16"

1 5/8" 27/8" 3 5/8"

4 3/8"

2 column 3 column 4 column

Operating Pressures

Every MYSON COLUMN radiator is tested to a pressure of
13 bar (188.5 psi) and is suitable for a working pressure of up to
10 bar (145 psi).

Radiator Brackets

Floor Bracket SK

Mounting Brackets (supplied with every radiator) - Wall Brackets

Fixing Brackets - Clamped Floor Bracket FK

COLUMN Mounting Bracket Detail

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

07

39/16"

2

15

/

16

"

4

3

/

32

"

5

/

16

"

Dimensions of base-plate

for Floor Bracket SK

Two-part cover for base-plate
in white plastic 45/16" x 55/16"

Complete system for free-standing
radiators, from 2-6 column up to
1000mm height. Painted to RAL 9016.

Includes:

- 3mm thick base-plate for fixing to
either finished or unfinished floor

- upright support 35 x 10 x 1.5mm,
fixing set with adjustable bracket,
security fixing, anti-vibration insert

- adjustable bottom support with
spacer and security fixing,
anti-vibration insert, white plastic
end stop for top of upright.

Height of

Upright

Order Code

18"

24"

30"

Base-Plate Cover

Height of

Radiator

12"

18"

24"

5

0-20046

5

0-20061

5

0-20076

COVERSK

Floor Bracket SK (Optional)

COLUMN Floor Bracket Detail

49/16"

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

The table on the right gives
recommendations for the
number of brackets to be used
with each radiator.

The strength of the wall should
be checked for its load-bearing
capabilities before installation.

Type

2 to 4 Column

Number of Sections

0 - 20

21 - 40

4 6

Up to 39” Height: Wall ­Mounted Angle Brackets - RW
Radiator Bracket - RH

4

6

Floor Mounting Floor
bracket - SK

2 3

4 6

Over 39” Height: Wall ­Mounted Angle
Brackets - RW
Radiator Bracket - RH

4

6

08

Height
24in

Height
18in

Height
79in

Architecture Range - Bench Radiator

4 COLUMN

Height
1

2in

Height
1

8in

Height
2

4in

Height
24in

H

L

4 COLUMN3 COLUMN2 COLUMN

2

1

/

2

in

4in

5

1

/2 in

Fixing Brackets

Product Code: FK1021
Product Code: COVERFK

COLUMN Sizes & Outputs

Length inc. seat Height inc. seat Depth inc. seat Output Output

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

NOTES:

1. All dimensions are nominal.

2. Heat outputs are based on

1800F AWT and 680F EAT (mean water to air

temperature of 1120F)

3. For heat outputs at other temperatures see page 13.

2 COLUMN

No. of Sections

Weight (lbs)

Ou

tput (Btu/h)

Order Code

24

12

19.8

1485

12 - 2045

32

16

26.5

1980

16 - 2045

40

20

33.0

2474

20 - 2045

47

24

39.6

2969

24 - 2045

55

28

46.2

3464

28 - 2045

72

36

59.4

4454

36 - 2045

24

12

25.9

1925

12 - 2060

32

16

34.6

2567

16 - 2060

40

20

43.2

3209

20 - 2060

47

24

52.0

3850

24 - 2060

55

28

60

.5

4492

28 - 2060

12

6

41.4

3006

6 - 2200

16

8

55.2

4008

8 - 2200

20

10

69

.0

5010

10 - 2200

24

12

82.8

6012

12 - 2200

30

15

103.5

7515

15 - 2200

Water Content (gals)

1.68

2.24

2.80

3.36

3.92

5.00

2.10

2.80

3.50

4.20

4.90

3.00

4.02

5.02

6.02

7.53

Length (in)

3 COLUMN

No.

of Sections

Weight (lbs)

Output (Btu/h)

Order Code

32

16

27.5

2380

16 - 3030

40

20

34.4

2975

20 - 3030

56

28

48.2

4265

28 - 3030

72

36

62.0

5355

36 - 3030

24

12

29.6

2674

12 - 3045

32

16

39.5

3565

16 - 3045

40

20

49.4

4456

20 - 3045

48

24

59.3

5347

24 - 3045

56

28

69.3

6439

28 - 3045

24

12

41.4

3566

12 - 3060

32

16

55

.2

4

755

16 - 3060

40

20

69

.0

5944

20 - 3060

48

24

82.8

7132

24 - 3060

56

28

103.5

8321

28 - 3060

Water Content (gals)

2.42

3.02

4.23

5.44

2.41

3.22

4.02

4.83

5.63

3.

00

4.

02

5.02

6.02

7.5

3

Length

(in)

72

36

88.9

8021

36 - 3045

7.24

No.

of Sections

Weight (lbs)

Output (Btu/h)

Order Code

24

12

51.6

4

213

12 - 4060

32

16

68.8

5618

16 - 4060

40

20

86.0

7022

20 - 4060

48

24

103.2

8

426

24 - 4060

Water Content (gals)

4.00

5.33

6.67

8.00

Length (in)

09

Architecture Range - Bench Radiator

BEN

CH Sizes & Outputs

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

No. of Sections

Weight (lbs)

Output (Btu/h)

Order Code

53 x 19 x 14

5

75

3528

23-05-6100

53 x 21 x 14

6

8

7

4231

23-06-6100

61 x 19 x 14

5

85

4185

23-05-6120

61 x 21 x 14

6

99

5022

2

3-06-6120

73 x 19 x 14

5

1

46

6452

23-05-6150

73 x 21 x 14

6

1

61

7530

23-06-6150

85 x 19 x 14

5

1

72

7868

23-05-6180

85 x 21 x 14

6

1

90

9182

23-06-6180

9

3 x 19 x 14

5

1

86

8895

23-05-6200

Water Content

(gals)

3.75

4.49

4.41

5.28

4.52

6.50

5.34

7.64

5.90

Dimensions (in)

LxHxW

93 x 21 x 14

6

2

05

10383

23-06-6200

8.42

3"

1

3

/8"

Thermostat

H

14

9

/16"

11

13

/16"

5

5

/

16

"

A

15

/

16

"

5

5

/

16

"

1

3

/

16

"

2

3

/4"

2

15

/16"

3

15

/16"

Thermostat

1

/2" Valve Body

Detail "A"

Y

Radiator Length + 13

3

4

"

Technical Data

Radiator Length - 2

9

/16"

Radiator Lenth + 1

3

/8"

3

15

/16"

NOTE: All dimensions are nominal.

Radiator Length

39

3

/

8

39

3

/

8

47

1

/

2

47

1

/

2

59

1

/

16

59

1

/

16

70

7

/

8

7

0

7

/

8

78

3

/

4

78

3

/

4

Rough - in (cc)

36

13

/

16

36

13

/

16

44 11/

16

56

1

/

2

68

5

/

16

76

3

/

16

(in)

(in)

44 11/

16

56

1

/

2

68

5

/

16

76

3

/

16

X

10

Typical hydronic system types

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

11

The following drawings are general examples.

Consult a certified heating professional for your specific application.

RADIATOR optional piping arrangements

RADIA

TOR valve selection

Valve application

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

12



All installations require 2 valves per radiator



All valves are ½” BSP thread for

connection to the radiator and
½” NPT thread for connection to the system (also includes compression nut
and ferrule for connection to ½” copper



Valves are available in 3 basic patterns: angle, straight, and inv

erted angle (TRV only)



Basic Installation: use 2 – LKD16AN (angle)

or LKD16SN (straight)

manual valves, nickel plated with screwdriver stops and caps



Basic upgrade: use 1 ‐ FF16WAC and 1 – FF16LAC manual valves, angle
only, chrome plated with white handles (FF16WAC is adjustable for
balancing, FF16LAC is fixed open but can be closed for service)



TRV (thermostatic radiator valves) are available for

automatic temperature control of individual
radiators: available in 3 body patterns, with or without thermostatic head (sensor), use in conjunction
with LKD or FF



TRV remote sensors and adjusters

available for special applications



DCK12 – 4” chrome nipple with

compression connection available for use with all Myson valves,

includes escutcheon (connects valve to heating system)



DAV12

– same as

DCK12

with addition of integral ball stop angle valve



Deco

rative pipe covers and escutcheo

ns

available in chrome or white (use

to cover exposed copper pipe used in radiator installation)

LKD16AN LKD16SN FF16WAC FF16LAC TRVanglew/HEAD

RemoteSensorRemoteAdjuster TRVstraight TRVinvertedangle TRVHEADonly

DCK DAV

COLUM

N C

onversion Fact

ors / Start-up & Maintenance

Heat output factors / Start - up and Maintenance

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

13

Failure to flush system of debris and flux may cause premature radiator failure, which
can result in leaks and property damage NOT covered under the Myson Warranty.

Step 1 Fill and vent the system.

Step 2 Run the system for two (2) hours at full temperature with all radiator valves in the open position.

Step 3 Shut off and drain the system while the water is still hot.
Step 4 Refill the system.
Step 5 Reheat, vent, and balance the system.
Step 6 Once the Décor Radiator is filled with water the system should be left filled.
Step 7 System should be checked for leaks on seasonal start-ups. Leaks must be repaired

as automatic system fill valves allow fresh water/oxygen into the system attacking radiators
internally.

SYSTEM START-UP

MAINTENANCE &

CLEANING

1

Once

operating,

avoid

the introduction of fresh water and oxygen to the system to prevent corrosion.

2 An occasional wiping with a damp cloth using a non-abrasive detergent can protect the finish of your

Myson Décor Panel Radiator.

3 The use of abrasive cleaners will damage the surface of your radiator and void the

manufacturer’s warranty.

Heat Output

The heat outputs for all MYSON COLUMN radiators can be found on pages 9 and

10. The tabulated figures are quoted in accordance with EN 442 for a mean water to
air temperature of 1120F. This is based on an average water temperature of 1800F
and an ambient air temperature of 680F. When the difference is not 1120F, the
output should be multiplied by the appropriate factor from within the table below:

Aver. Water Temp.

0

F

Ambient Air Temp.

0

F

190 68

180 68

170 68

160 68

150

68

140 68

120 68

Water to Air

(D

elta T 0F)

Conversion Factor

122

1.14

112 1.00

102

.91

92 .79

82

.68

72

.58

52

.38

NOTES

Notes

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

14

NOTES

Notes

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

15

heatingthroughinnovation.

MYSON

Myson Inc./Rettig USA 45 Krupp Drive, P.O. Box 1460, Williston, VT 05495 www.mysoncomfort.com

COLUMN 3/2014