My Music Group E13 User Manual

成品尺寸：50x65mm
材质：正反面印刷，128G双铜纸

FCC ID：QIFE13

正面

POWER ON

Press and hold the Multi-function button for about 3
seconds, hear prompt”Power on”, Blue light flash

TWE paring

1.Keep the distance between the device and the
Bluetooth Earbuds within 3 feet(for pairing only)

2.Press and hold the multi-function button on both
earbuds for a few seconds until you hear prompt “

Power on”, and see blue lights flashing

3.You will hear prompt”Left Channel” on Left Earbud
and “ Right Channel” on Right Earbud to begin pairing.

Connect TWE to your device

Active the Bluetooth function on your device to search
the“Sonic Capsule” and connect to it. You will hear ”
Pairing success, sort connected” from the Master
Earbud(Right Earbud-Factory default setting), and blue
lights flashing. It is ready for use.

NOTE:

Factory default setting is RIGHT Earbud as MASTER
Earbud. To reset/change MASTER Earbud, hold
multi-function button on BOTH earbuds for 6
seconds. When blue/red lights flash quickly, press
multi-function button twice on the earbud you
want to set as the MASTER Earbud.

反面

POWER OFF

Long press the Multi-function button for about 4
seconds, hear”Power off”, the two earbuds will power
off together.

HANDS FREE FUNCTION

Short press the multi-function button to answer an
incoming call / end an ongoing call;
Long press the multi-function button to refuse an
incoming call
Double press the multi-function button to call the
number that last called you
REMARK: the operation only support master earpiece.

SINGEL EARBUD PAIRING

1.Press and hold the multi-function button for about 6
seconds, until you hear “ Power on” then “Pairing”, the
blue/red lights flash quickly. (the other Earbud should
be off during this process.)

2.Active the Bluetooth function on your device to
search the “Sonic Capsule” and connect to it.

3.You will hear prompt” Pairing success, sort
connected”. It is ready for use.

CHARGING THE BLUETOOTH EARBUDS PRODUCT’S SPECIFICATIONS

Please fully charge before first use

To charge your earbuds: simply return them to the
charging station, Press the Power button one time and
the LED on charging station show blue, and close the
lid. While charging, the earbuds’s LED show red color, it
become blue color after full charged.
Charging time: around 1-1.5 hours
Play time: 2hours

CHARGE YOUR CHARGING STATION

Plug the provided micro USB charging cable into the
charging station and an active computer USB port or
USB AC adapter that is plugged into an active wall
outlet. The LED light is red color and will die out after
full charged.
Charging time: 2 hours

Bluetooth version: 4.2
Speakers: D8mm *2
Frequency response: 200HZ-200KHZ
Battery build-in earpiece: 40mAh*2
Charging Station battery: 600mAh
Charging current: 60mA DC 5V

NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment. This device complies with Part
15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.

reception, which