MYE MWTD-S9 Operation Manual

MWTD-S9

Digital Input 900MHz

Single Channel Transmitter

Operation Manual

.manmwtds9v4

www.myeclubtv.com

CONTENTS

INDUSTRY CANADA COMPLIANCE…………………………3
MWTD-S9 ORIENTATION……………………………….…….4
SAFETY PRECAUTIONS………………………………………5
SETTING THE TRANSMITTER…………………….…………6
CONNECTING THE TRANSMITTER…………………………6
AUDIO AND AUTOMA TIC LEVEL CONTROL….……………7

SPECIFICATIONS…………………………………………….....7

MWTD-S9 MOUNTING BRACKET………………………..….8
WARRANTY…………………………………….…..…….…9/10

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules.
Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause u ndesired operation.

This equipment has been tested and f ound to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio fre quency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that in terference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television rec eption, which can be determined by turning th e
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This equipment has been verified to comply with the limits for a Class B computing device, pursuant to the FCC Rules. Operation
with non-approved equipment is likely to r esult in interference to radio and TV reception. The user is cautioned that changed and
modifications made to the equipment without the approval of the manufacturer could void the user’s authority to operate this equipment.

2

INDUSTRY CANADA COMPLIANCE INFORMATION

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.

This radio transmitter (IC: 6662A-MWTDS9) has been approved by Industry Canada to operate with the antenna types listed
below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this
device.

¼ whip antenna – maximum gain of 2 dBi, 50 ohm

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference , i ncluding interference that may cause undesired operation of the
device.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélect ri que
à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à

l'établissement d'une communication satisfaisante.

Le présent émetteur radio (IC: 6662A-MWTDS9) de modèle s'il fait partie du matériel de catégorieI) a été approuvé par
Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et
l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le ga in est sup érieur au
gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

¼ whip d'onde, le gain max 2 dBi, 50 ohm

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

3