mychway HR-T350 User Manual
Page 1 , in 12 pages
—Please read the instructions before use！
Ⅰ.Brief Introduction
E-light applies three core technology, IPL, RF, and epidermis cooling. It combines the
USER MANUAL
Page 2 , in 12 pages
advantage of IPL and RF, in one hand, the skin absorbs IPL energy selectively, and the skin also
absorbs RF energy, on the other hand, the RF-surface-touch cooling technology removing the
discomfort and complications by high heat of IPL. Therefore, the effect and safety of E-light
makes a breakthrough.
1.Principle
Applying the technique of IPL and Bi-polar Radio Frequency, the equipment acts on the
entire skin corium and connective tissue, stimulates the collagens of different depth to realign
and grow, then gets treatment effect. Bio-polar RF release energy at the same time, with the
selective absorption for the skin to light energy, various pathological tissues of corium and
epidermis creates Photothermolysis effect. Since light energy is far below conventional IPL, the
pigment tissue and vascular pathological tissue of the corium and epidermis would absorb more
energy without injuring the epidermis, and then remove these pathological tissues better and get
the effect.
2. Application：
1. Hair removal;
2. Skin rejuvenation;Wrinkle removal, fact lifting;
3. Removing freckle, age spots, sun spots, chloasma, pigmentation troubles, etc;
4. Vascular removal;
5. Acne treatment.
3. System Self-checking
The circuit of system entering the self-checking situation when the machine starts, leave
the machine carry on the self-checking for 5-10 seconds, then continue the operation.
4. System Classification
Electric shock protection：Grade1 BF Grade
Corrosion prevention liquid：ordinary
Do not use the machine in the environment mixed of flammable narcotic and air or nitrogen
oxide mixture.
5. Equipment Consist, Specification, and Accessory List
Page 3 , in 12 pages
1. Equipment Consist:
1.1. Mainframe
A. Power supply system
B. Microcomputer system
C. Monitor
D. Cooling System
1.2. E-light Handpiece
A. Intense pulsed light source, xenon lamp
B. Reflector and filter
C. Sapphire wave guide
2. Technique Specification
Light Energy: 1－50J/cm2
RF energy: 1-25J
SR Spectra: 530-1200nm
Cooling: water + air + semi-conductor
Spot size: 8×40mm
N.W.: 35kg
Voltage: 110V±220V 10%, 50~60Hz;
3. Accessory List
Parts List
Ⅱ.
St
handle
Power cord
Fuse
Funnel
Protective goggles
Patch
Key switch
Page 4 , in 12 pages
andard Treatment Process
2.1 Form filling
Fill in the blanks of the Client File, confirm the treatment program, remind the client pay
attention to some points before and after treatment.
2.2 Face cleaning
Clean the face with gentle face cream for 3 minutes.
Remind: clean the hands of operator and the handpiece with bromogeramine.
2.3 Preheating
Start the equipment after face cleaning, preheat for not less than 3 minutes (without lighting
the xenon lamp).
2.4 Shaving
Shave the unwanted hair of the treatment area(2 minutes).
2.5 Gel coating
Coating the gel evenly (2-3mm) on the skin.
Effect：light guide, cooling, anaesthetisin.
Attention: no coating on eyes, eyebrows, lips.
2.6 Eye protection
Operator: wear the safety goggles.
Patient: close the eyes, wear professional safety goggles or cover the eyes with eye patch.
2.7 Allergic test
Emit 2 or 3 light spots in the bottom of ears in safe parameter, observe for 3 minutes.
Effect: do not continue to operate if there is a allergic phenomena.
2.8 Operation
Carry on the operation with a suitable parameter to the operatee.
Attention：
2.8.1 Inform the operatee that there will be a slight pricking in operation before operating, to
avoid panic.
2.8.2 Start the operation with a low energy grade, adjust the parameters in operating while asking
the feeling of the operatee.
Loading...