MXL Revelation Solo User Manual

SOLO

Professional Audio Division, El Segundo, CA

Phone: [phone]

www.mxlmics.com

Marshall Electronics



[phone]  Fax: [phone]



www.mogamicable.com  [e-mail]

Cardioid Pattern Tube Microphone

SOLO

An Introduction to the MXL Revelation Solo

Thank you for choosing the MXL Revelation Solo. Your new Revelation Solo

microphone was designed and engineered in the USA by our world-class team

of electrical and audio engineers and is built for the most critical sound ap­plications. The newest member of the MXL flagship product family, the Rev­elation Solo is an extraordinary studio microphone that delivers the warmth

and intimacy of a tube mic with clarity and punch for balanced recording.

The MXL Revelation Solo features individually selected components,

chosen for their superior sonic capabilities. Examples include the EF86

pentode tube and balanced transformer output. The MXL Revelation Solo

also includes a roll-off, phase reversal and -10dB pad.

User Manual

Warranty

Marshall microphones are guaranteed against defects in material and workmanship for three
years (except tube which is 90 days) from date of purchase. Should you encounter any problem
with this unit, promptly contact the company you purchased it from for assistance. The original
dated sales receipt will be necessary for any warranty claim. Do not send any unit directly to us
without prior authorization from our service department!

Warranty coverage is limited to repair or replacement (at our option) of the microphone, and
does not cover incidental damages due to use of this unit, nor damage caused by accidental
misuse of this product.

The MXL Revelation Solo will provide many years of outstanding service

and the finest quality recordings attainable. Before you get started, we

encourage you to review this manual. Inside you’ll find some

recording tips, tricks and specific features of the MXL Revelation Solo that

will help you obtain the best possible recording results.

Enjoy your MXL Revelation Solo!

The MXL Team

1

Professional Audio Division, El Segundo, CA

Phone: [phone]

www.mxlmics.com

Marshall Electronics



[phone]  Fax: [phone]



www.mogamicable.com  [e-mail]

10

SOLO

User Manual

Specifications

Cardioid Pattern Tube Condenser

Type: Microphone

Diaphragm: 6 micron diaphragm

Tube Type: EF86

Frequency Range: 20 Hz-20 kHz

Polar Pattern: Cardioid

Sensitivity: -40 dB re 1 V/Pa

Impedance: 140 ohms

Pre-Attenuation Switch: 0 dB, -10 dB

S/N Ratio: 76 dB

Equivalent Noise Level: 18dBA (A-weighted IEC 651)

Max SPL for 0.5% THD: 138 dB SPL

High Pass Filter: 12 dB/octave @ 125Hz

Revelation Solo Features

Carefully unpack your MXL Revelation Solo Cardioid Pattern Tube microphone to verify that
all of the components are included. Your MXL Revelation Solo includes the following:

• Revelation Solo Microphone

• 15ft 7-pin Mogami® cable

• 15ft XLR Mogami® microphone cable

• Revelation Solo power supply

• Shockmount

• Aluminum flight case

• Cleaning cloth

If any of the above items are missing or damaged, contact the company you purchased
it from for assistance.

Power Requirements

The MXL Revelation Solo uses an EF86 tube that requires a dedicated power sup­ply unit (included with your microphone). Even if your mixer has phantom power, it is
recommended that you defeat the phantom power as a precautionary measure when it
is not needed to power other mics that you might also be using.

This supply is switchable between 110 volts and 220 volts AC. In North America, the
microphone ships in the 110 volts AC position and in the 220 Volts AC position for
export. However, you always want to ensure that the power supply voltage is correctly
set for your local voltage as permanent damage to the microphone and/or power supply
may occur if the incorrect voltage setting is selected. Every Marshall Electronics MXL
microphone has been thoroughly checked before shipping; so if you do not hear sound,
check that the power supply is switched on.

Revelation Power Supply Unit
Power Requirements: 110/220 VAC, 50/60Hz

Size: 7 1/2” X 2 1/2” (mic only)

Weight: 2lbs (mic only)

Metal Finish: Dark Violet and Chrome

9

Caution

Do not “hot plug” the mic. Always ensure that the power supply is off when plugging
and unplugging the included 7-pin cable from the microphone to avoid damaging the
microphone and power supply.

Bass Roll-off Switch

Bass Roll-off
Switch

XLR Mic Output

Ground Lift
Switch

Phase Switch

7-pin Mic Cable

Power on LED

2

SOLO

User Manual

The Revelation Solo power supply features a bass roll-off switch to help reduce prox­imity effect. Proximity effect is distortion that often occurs when a sound source is too
close to the mic. Some microphone patterns boost bass as you get closer to the micro­phone; cardioid mics, for instance, tend to boost bass. The bass roll-off switch reduces
the low frequencies for a more full range sound.

Phase Switch

The Revelation Solo also includes a phase switch which allows you to reverse the polar­ity of the microphone signal by 180 degrees. This can help minimize phase issues when
recording with multiple microphones.

Polar Pattern

One of the most popular polar patterns, a cardioid microphone picks up sound from
the front of the microphone, less sound from the sides, and has good rejection of sound
to the back of the microphone. The cardioid pattern is well suited for situations when you
want to pick up specific sound sources like a guitar within an ensemble and is recom­mended for recording applications where the acoustics are good but not perfect. For
instance, a cardioid pattern is less likely to pick up ambient noise from computers and
recording equipment.

Ground Lift Switch

A ground loop is unwanted interference that can be created when multiple electronic
devices improperly share a common ground. The Revelation Solo includes a Ground Lift
switch to help prevent such occurrences. If a ground loop is audible (usually a 50-60Hz
humming noise), the ground lift switch on the front of the power supply should be set to
the ‘lift’ position.

-10dB Pad

The Revelation Solo can be used in very loud sonic environments without significant
distortion. If you hear distortion from the microphone, engage the “-10dB pad”
on the rear of the microphone to the -10dB position. You may also move the
microphone farther away from the sound source.

Shockmount

The Revelation Solo comes with a custom shockmount specifically designed to handle
its large size. Shockmounts decouple the microphone from the mic stand and the
environment and can minimize floor noise as well as
noise induced by people handling the microphone
stand. Shockmounts should be considered “standard
equipment” for all recording applications. To mount
the Revelation Solo in the shockmount, first attach
the shockmount to the mic stand. With one hand,
hold the Revelation Solo microphone inside the bas­ket of the shockmount with the threaded base of the
mic resting on the retaining nut at the bottom. With

Fig. 4C

Front View

centered over the instrument (see Fig. 4C).

1

Side
View

1

Single Microphone / Open Top: If
you are using a single microphone, it
is generally recommended that you
record from above, as placement of the
microphone in the lower center may
interfere with the performer’s ability to
access the pedals and the microphone
will likely pick up excessive pedal and
other mechanical noise. Position the
microphone just over the open top,

Recording a Drum Set

Like the piano, capturing the drums can be quite a challenge, if for no other reason than
the fact that you must be very careful to avoid positioning the microphone(s) where they
could be hit! Ideally you’ll want a minimum of two microphones for this job, though a
single microphone can be employed.

Fig. 5A

1

Front
View

Front
View

become that much more difficult to capture if the room has hard, reflective surfaces,
resulting in a muddy sound without any real definition. Further, you should always
record the drums dry and add signal processing after the fact.

2-3 Ft. apart

16-20” above performer’s head

1

2

Fig. 5B

16-20” above
performer’s head

Stereo Overhead Pair: Position the two
microphones approximately 16 – 20
inches above the performer’s head,
separated laterally by roughly 2 - 3 feet
and placed 5 – 6 feet out in front of the
drum kit. Adjust the two microphone’s
Pan position so that you achieve a
good stereo spread, though generally
not hard left and right (see Fig. 5A).

Single Overhead Microphone: Position
the microphone approximately 16 – 20
inches above the performer’s head

- centered in front of the drum set,
and placed 5 - 6 feet out in front. The
microphone’s Pan position should be
centered for mono drums (see Fig. 5B).

For best results, record the drums in
as acoustically “dead” a room as you
can. If the room is live, the sharp at­tack transients of the drum kit will only

3

8

SOLO

User Manual

Placement of the amp is another important factor. If the amplifier sits on a carpeted floor, you are
more likely to reduce the amount of brightness in the sound. Similarly, elevating the ampli­fier off the floor may result in a loss of low end. If you’re looking for a big reverberant tone,
placing the amp and microphone in the bathroom is another popular technique. The hard tiles
and other reflective surfaces can do wonders for a dull sound. In this case, move the microphone
back a few feet from the loudspeaker and crank it up!

Recording the Piano

Top View

2

Front View

Fig. 4A

The piano is one of the most challenging
instruments to record, and many problems
stem from the quality and maintenance of
the instrument itself. You’ll obtain the best

or a single

*

mic here

or a single

mic here

2

1

*

results by using an instrument that has
just been tuned and is in good mechanical

1

condition.

The piano is generally recorded using close

miking technique. Ideally, you’ll want a
minimum of two microphones. Usually, the microphone capturing the higher strings is
assigned to the left channel and the microphone capturing the lower strings is assigned to
the right channel in the final stereo mix, though the stereo spread generally is not hard left
and right. While a single microphone can be used, the lower and upper extremities of the
instrument will likely be compromised.

Grand Piano: For the upper strings, position the microphone approximately 8 inches from the
piano hammers (to reduce mechanical noise) and 8 - 11 inches above the strings, with the
Pan position set to left of center. For the lower strings, position the microphone toward the far
end (away from the keyboard) roughly 6 - 12 inches from the end and 8 - 11 inches above the
strings, with the Pan position set to right of center. Position the piano’s lid at full stick (see Fig.
4A). If you are using a single microphone, position the microphone approximately 8 inches
from the piano hammers (to reduce mechanical noise) and 8 - 11 inches above the strings

- centered over the piano’s mid point. Pan position should be centered and the piano’s lid
should be at full stick.

your other hand, rotate the retaining nut until the microphone is securely attached
to the shockmount.

Microphone Cables

The microphone cable can have a profound effect on
the sound of any microphone. Even the finest mi­crophones will sound poor if the interconnect cable
allows noise to enter or causes distortion and loss of
information. We highly recommend exclusively using
the Mogami® cables supplied with your Revelation
Solo.

Care

Dust and foreign material can degrade the performance of a microphone over time
so always store the unit in its case.

Grill

The Revelation Solo microphone uses a single layer mesh grill. This design
minimizes standing waves and harmonic distortion. Because this type of grill
leaves little protection between the user of the microphone and the capsule, we
highly recommend using a pop filter. Use of a pop filter will help protect your
microphone’s sensitive capsule, keeping it free from moisture caused by saliva

and breath condensation.

Recording Tips and Tricks

Upright Piano: With an upright piano, the two microphones are generally placed either
just over the top of the piano with the top open, or you can remove the piano’s front
panel beneath the keyboard and place the microphones below.

Front Panel Placement: For the upper strings,
position the microphone approximately
8 - 11 inches away from the strings, with

Front View

Fig. 4B

Side View

the Pan position set to left of center. For the
lower strings, position the microphone 8 - 11
inches away from the strings, with the Pan
position set to right of center (see Fig. 4B).

2 1

Front Panel Removed

Mics positioned

8-11” away from strings

7

4

SOLO

Vocals and Dialog

phone. Getting too close to the microphone tends to increase bass response and can create
problems with plosive sounds (i.e., those popping Ps, Bs, Ds, and Ts). Getting too far away
makes the microphone more subject to picking up room ambience and creates the effect of
the vocalist being in a bowl. While vocalists may need to move about in order to hit those
high notes, make every effort to maintain a constant distance from the microphone, as this
will provide the greatest tonal balance (see Fig. 1). For the most part, the microphone’s axis
(or center line) should aim toward the nose and mouth to obtain the fullest sound. It’s not a
bad idea, however, to experiment angling the microphone slightly away from dead center
so as to help minimize plosives. Further, you should always place a “pop” filter between the
vocalist and the microphone, with the pop filter positioned 3 - 4 inches in front of the micro­phone. This will greatly increase your ability to achieve the most natural sounding recordings
with minimal interference from plosive sounds. Fixing plosives with audio editing software
often creates more of a problem than the plosive itself. Use of a pop filter will also protect
your microphone’s sensitive capsule, keeping it free from moisture caused by saliva and
breath condensation. Remember—good microphone technique, proper positioning, and use
of a pop filter can make all the difference between a so-so vocal recording and a great one.

Fig. 1

Ideally, you want to record vocals in a rela­tively “dead” room. If you clap your hands
and get an echo effect, you should consider
adding some carpet, blankets, drapes, or
other sound absorbing materials. On that
note, make every effort to avoid getting
too close to the room’s walls. These hard,
reflective surfaces can easily complicate the
recording process. Move your mic setup
toward the room’s center.

Generally, you should position the vocalist
roughly 6 - 8 inches away from the micro-

User Manual

Twelfth Fret Placement: Placing the microphone roughly 2 - 4 inches from the twelfth
fret and aimed directly at the strings will generally produce a warm, full bodied sound
with good tonal balance. In addition, the sound hole’s contribution to the sound will be
moderated since the microphone is not pointed directly at it.

Bridge Placement: Similarly, you can position the microphone so it is 3 - 6 inches from the
guitar’s bridge. This will generally produce a somewhat brighter tonal quality. You should
also be prepared to experiment with positioning the microphone slightly off-axis should you
find yourself capturing too much low frequency response from the guitar’s sound hole.

The acoustical characteristics of your room will also have a pronounced effect on your
results. A “live” room will produce an overall “brighter” guitar sound, while a “damped”
room will produce more of a mellow tone. If you have two microphones, you may wish
to experiment using one in close proximity to the guitar as previously described, with the
second microphone on a stand a few feet away to capture the room’s ambience. Blending
the two sources can produce excellent results.

Recording an Amplified (Electric) Guitar

While the electric guitar can certainly be recorded directly, there are times when there is
simply no substitute for the sound of a real amplifier. Guitar amps have particular gain
stages that facilitate the popular “crunch” guitar sound. While digital modeling and pro­cessing systems certainly have their place, they may not have the same level of realism as
the sound from an amplifier. A small guitar amp can be just as effective for this application
as a stack, because you don’t necessarily need to “crank” the volume.

Instead, you want to increase the amp’s initial gain to achieve the desired amount of
overdrive.

Fig. 3

Top View

Side View

Recording Acoustic Guitar

Fig. 2

Bridge
Placement

sound hole, doing so usually increases low frequency response to the point of making the
instrument sound “boomy.”

12th Fret
Placement

Your best results for capturing the acoustic
guitar (or any similar stringed instrument)
begin with a properly tuned instrument and
strings that, while not old, aren’t so new as
to create tuning issues due to stretching.
There are two optimum points for micro­phone positioning: either near the bridge or
by the twelfth fret.

While it may seem natural to place the
microphone in front of the instrument’s

5

Mic is aimed
directly at center
of loudspeaker

Typically, a guitar amp is close miked to achieve the highest direct sound. Placing the
microphone roughly 4 inches from the grill, aimed directly at the center of the loudspeaker
will produce the most “edge” to your sound. By angling the microphone slightly off axis
and towards the wall, you can add more “room sound.” Experimentation is a key factor in
achieving the sound you are looking for (see Fig. 3).

Mic is positioned

4” from grill

4”

6