Muztag Q10 Instruction Manual
Gas Fire Patio Heater
Q10
Instruction Manual
Please read the manual BEFORE you unpack or install the fire
2
TABLE OF CONTENTS
Warning
3
Getting Started
4
What’s Included
5
Assembly Procedures
6
Product Drawing
8
Heater Stand and Location
8
Gas Requirements
9
Leakage Test
9
Lighting Instructions
10
After Use and Storage
10
Cleaning and Maintenance
10
Troubleshooting Checklist
11
Spare Parts
12
Warranty
13
Contact
14
3
WARNING
PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION AND INSTALLATION
REPAIRS SHOULD ONLY BE DONE BY A QUALIFIED TECHNICIAN ONLY
Do not use this appliance for indoors, as it may cause personal injury or property damage. THIS APPLIANCE
MUST ONLY BE USED OUTDOORS.
Do not connect the heater to any gas supply until it has been fully assembled.
This outdoor heater is not intended to be installed on recreational vehicles and/or boats.
Appliance should be located on a solid surface.
Maintenance and repair should be carried out be a qualified technician.
Improper installation, adjustment, alteration can cause personal injury or property damage.
Do not attempt to alter the unit in any manner. Any modifications may be dangerous and are not permitted.
Do not store or use petroleum or other flammable vapors or liquids in or near the heater unit.
The whole gas system, hose, regulator, pilot or burner should be inspected for leaks or damage before use,
and at least annually by a qualified technician.
All leak tests should be done with a soap solution. Never use an open flame to check for leaks.
Do not use the heater until all connections have been leak tested.
Turn off the gas valve if smell of gas is detected and immediately shut off any gas supply.
Do not move heater while it is operation.
Do not move the heater until temperature has fully cooled after it has been turned off.
Control compartment, burner and circulation air passageways of the heater must be kept clean.
Frequent cleaning may be required as necessary.
All gas cylinders should be turned off when the heater is not in use.
Check the heater immediately if any of the following occurs:
The heater does not reach temperature.
The burner makes popping noises during use (a slight noise is normal when the burner is extinguished).
Smell of gas in conjunction with extreme yellow tipping of the burner flames.
The burner does not ignite or continues to go out
The gas regulator and hose assembly must be located in the cylinder cabinet where gas cylinder is installed.
Any guard or other protective device removed for servicing the heater must be replaced before further use.
Adults and children should stay away from high temperature surfaces to avoid personal injury or property
damage. WARNING: Accessible parts may be very hot.
Children should be carefully supervised at all time when they are in the area of the heater.
Clothing or other flammable materials should not be hung on the heater or placed on or near the heater.
Do not use the heater for any form of cooking.
Do not throw anything into the heater.
Do not leave the heater unattended whilst in operation.
Do not use heater in excessively windy conditions.
Do not user heater in excessively rainy conditions, as this could lead to damage to components.
Ensure the gas supply is isolate and shut off when not in use and gas control valve is in the OFF position.
Follow all instructions regarding the use of LPG and Butane bottles. Please contact your local gas supplier for
further advice if needed.
WARNING: Flames from the heater are almost invisible in direct sunlight.
4
GETTING STARTED
Please read instruction thoroughly before using the appliance.
The gas heater will arrive in one box containing the appliance with burner already installed, adjustable feet,
surrounding safety glass with brackets, valve ignition key, standard propane regulator, 60cm gas hose, glass and
lava rock fuel beds and rain cover.
Remove the appliance from packaging. Carefully place it down on the floor, keeping it upright for ease of
assembly.
Extreme care should be taken when handling the heater, to ensure the gas pipes, thermocouple lead, gas
valve or burner are not damaged or loosened in anyway.
Please note: ALL heaters have been burn tested and leak tested prior to leaving the factory. Although each
unit is cleaned, there may be the odd scorch mark around the pilot and main burner gas jets.
Specification
The gas heater is designed to work with the following gas types.
Gas Type
LPG - G31 Propane
LPG - G30 Butane
Appliance Category
I 3+
I 3+
Supply Pressure
37 mbar
28-30 mbar
Heat Input
Max. 14KW
Max. 14KW
Maximum Flow Rate
1000g/hr
981g/hr
Gas Bottle & Regulator
The appliance includes 27mm clip-on regulator with 8mm inlet and 60cm of gas hose. This has a flow rate
capacity of 1.5kg/hr and operates a supply pressure of 37mBar. It is suitable for most domestic propane gas
cylinders available at garden centres, retailers and gas suppliers.
Other regulators are available depending on the gas type and cylinder size. Please ensure that a suitable
regulator with a minimum flow rate capacity of 1.3kg/hr and relevant supply pressure is used. Please contact
your local gas supplier for further advice if needed.
The gas hose should be checked regularly to ensure it is in good condition and it is recommended that it is
replaced in accordance with standard practices.
Propane or Butane
Although the heater will work with either propane or butane, there is a difference between the two gasses.
Butane cannot be used in temperatures below 5°C, whereas propane can be used all year round. We would
recommend propane
5
WHAT’S INCLUDED
Appliance Heater
Adjustable Feet
Surrounding Safety Glass
and Brackets
Standard Propane
Regulator & 60cm Gas
Hose
Glass and Lava Rock Fuel
Beds
Rain Cover
Gas Valve Safety Ignition
Key
Loading...